Search Documents

By Morris Muskat

A general theory has been developed for the effect of permeability stratification on the efficiency of the gas-injection phase of cycling operations. It has been applied to three special types of permeability variation; namely, exponential, probability, and linear. In the case of the exponential permeability distribution the effect of areal pattern sweep efficiency was also taken into account. The exponential permeability distribution can be characterized by the ratio of the maximum to minimum permeability, which has been termed the stratification constant. Curves were calculated for the variation in total wet gas recovery and total gas throughflow, to give that recovery to various abandonment limits of the wet gas content in the produced gas, as a function of the stratification constant. The cumulative wet gas recovery decreases monotonically as the stratification constant increases and is generally higher at the lower values of the wet gas content abandonment limits. The total gas throughflow first rises to a maximum as the stratification increases, and then ultimately declines. The effect of the areal sweep pattern efficiency is relatively minor as compared to that of the stratification constant, except in the region of low values of the latter where the formation is substantially uniform. The probability distribution can be characterized by a "variation" parameter varying from o to I as the formation changes from strict uniformity to extreme variability. The curves of total wet gas recovery and total gas throughflow to different abandonment limits of wet gas content versus the variation parameter have the same general characteristics as for the exponential permeability distribution. In the linear permeability distribution the ratio of maximum to minimum permeability also serves as a stratification constant index defining the distribution. The curves of total wet gas recovery and gas throughflow to fixed abandonment limits versus the stratification constant are similar to those for the exponential permeability distribution. However, for the higher values of the stratification constant the recoveries and throughflows do not asymptotically fall to o as in the latter, but approach constant values determined by the abandonment limit of wet gas content in the produced gas. Introduction It is becoming generally recognized that one of the most important factors determining the economic feasibility of cycling operations is the areal continuity and permeability distribution of the producing formation. While the effects of areal variations in permeability, porosity, thickness, and well pattern on the sweep efficiency can be evaluated by electrical model studies,' those due to permeability stratification require separate treatment. Several studies have been reported2,3 on the' influence of permeability variations on the wet gas recovery by cycling. In these, however, discontinuous permeability variations either have been assumed explicitly, or the analysis has been carried through as if they were discontinuous. While, in fact, the actual permeability profiles will undoubtedly be discontinuous, recent develop-

Jan 1, 1949

By C. D. Cochran, F. H. Deily, M. M. White, Victor Horner

A laboratory study of the effects of physical and easily measured rheological properties upon dynamic filtration was carried out. The purpose was to determine the factors affecting dynamic filtration and thus learn how to control this important property. The recommended procedure for determining the amount of fluid loss prescribed by API Code RP 29 "Field Procedure for Testing Drilling Fluids,"' is very useful for mud conditioning purposes, but inadequate for comparing filtration properties of different muds under dynamic conditions. Where dynamic filtration control becomes important for purposes such as logging and coring, other means of evaluating filtration properties are needed. A special device and testing technique were developed to provide reliable data on filtration characteristics of different fluids under dynamic conditions. Liquid saturated rock samples were drilled with a microbit, and the amount of connate liquid displaced by the fluid being investigated was measured. The empirical testing procedure was considered reliable. A large number of laboratory-prepared and field-mixed dritling fluids with a wide range of physical properties were studied. These properties included: (I) shape of consistency curves, (2) apparent viscosity, (3) plastic viscosity, (4) yield value, (5) density, and (6) API filter loss. Test results indicate that very little, if any, trend could be established between changes in these fluid properties and dynamic filtration. INTRODUCTION During the process of drilling, excessive loss of liquid from the mud to the formation is undesirable for many reasons. Filtration can reduce production-zone permeability, cause sloughing of formations, affect electric log curves, and render the fluid data obtained from cores unreliable. Thus, it is very important that we gain a knowledge of the factors that control filtration. It is generally agreed that in any type of filtration (static, dynamic, or combinations thereof), the mechanics of filtering depend in great part upon the composition of the fluid. Moreover, it is also true that the physical and rheological properties are influenced by the composition of the fluid. Indirectly, then, it was hypothesized that a relationship existed between dynamic filtration and physical-rheological properties, two effects of a common cause—fluid composition. This paper discusses an attempt to relate filtration-while-drilling to physical and easily measured rheological properties. It is believed that the results of this study may prove useful to others in the industry who are working on the problem of understanding filtration. The industry accepted practice for determining fluid loss from drilling mud is described in API Code RP 29. The practice is to measure the amount of filtrate that passes during a given interval of time from a quiescent drilling fluid under applied pressure through a piece of filter paper. This is primarily a test of static filtration properties. Other investigators have studied filtration under dynamic conditions. Williams5 and Pro-kop5 studied radial filtration and filter-cake buildup by circulating fluid through a porous cylinder under conditions similar to actual mud flow. Nowak,4 Krueger,3,4 and Vogel3 studied the effect of filtration upon permeability by flowing mud past the face of rock Samples. In their tests, the bit action was simulated by mechanical scrapers that kept the filter cake from building up. Ferguson and Klotz2 studied three types of filtration: static, dynamic, and beneath-the-bit. They investigated each type separately, using a model well in which bottom-hole hydraulics and mechanics were closely approximated.

Jan 1, 1958

By Percy Barbour

The town of Goldfield, Nevada, with the exception of six stone buildings, was burned to the ground to-day. One man is dead from causes attributed to the fire. A woman is missing and is believed to have perished and several persons were treated for burns as the result of the conflagration believed to have been of incendiary origin which started in the old Tenderloin District. The water supply was not sufficient and dynamite only scattered the frame structures and added kindling to the flames which were fanned by a forty-mile wind. Newspaper Dispatch, July 6. No former Goldfield resident could read that dispatch with unmixed feelings. About two o'clock one morning the crowded train from San Francisco landed me in Goldfield no more hours late than it habitually was. The desert air was clear and crisp and bracing but the pandemonium of cab and bus drivers did not drown out the sounds of music and merriment which floated from the blaze of light which was Goldfield about three-quarters of a mile from the station. As I stood in the ferry house, at the foot of Market Street, awaiting the Oakland Ferry, an old friend of mine, down to see who was departing for the greatest boom town of this generation, informed me that if I had made no reservation for quarters in Goldfield, I would be unable to obtain any, even chairs in the hotel lobbies were renting for $4 per night, and volun-teered the use of his room there for my convenience until his return. He described the house and location, which I identified without difficulty, but found no one to direct me to the room. I peered through a glass door into a room which seemed to be unoccupied and timorously entered and turned on the electric light., I found mail on the dresser addressed to my friend,

Jan 8, 1923

By R. M. Leibrock, R. P. Vincent, C. W. Ziemer

The Stanolind flowmeter, which employs a hot-wire anemometer connected in a Wheat-stone bridge circuit, has proved useful for determining the relative productive ability of individual sand members of gas wells. The operation of this instrument in measuring gas velocities in the well bore above each producing member has provided both a direct and accurate means of analyzing reservoir performance. Results of tests conducted with the well flowmeter in the Hugoton gas field of western Kansas have indicated some rather unusual production characteristics. In two cases it was found that all or the greater part of the total gas produced was coming from one section in wells where four "pay" sections had been perforated individually. These actual measurements contradict in many instances the indications of data obtained from electric logs and from core analysis; the fact that these latter sources often give incorrect results, demonstrates the necessity of a method, such as is provided by the well flowmeter, for accurately determining the amount of gas coming from each producing member. Introduction In any gas well where a number of pay sections have been perforated individually and are producing to a common outlet, the question arises as to the relative amounts of gas being passed through each set of perforations. In the past it has been the policy to depend on core analysis to estimate relative productivities, or, where the sections were not cored, to obtain some idea of production characteristics from electric-log studies. The weaknesses in these methods are readily apparent and indicate the need for more reliable means of measuring gas flow from each zone. The Stano-lind flowmeter* was developed for this purpose. Preliminary tests were made with the instrument in the Katy gas field near Houston; however, the bulk of the routine work with the well flowmeter has been confined to the Hugoton gas field in western Kansas, where results obtained have been encouraging. A description of the instrument, the field technique employed in testing, and a few of the results obtained in the Hugoton area are discussed in this paper. Description or Instrument The well flowmeter is 1¾ in. od and 7 ft long; it is entirely self-contained, can be run through tubing as small as 2 in. id in wells with high pressure (4500 psi) and temperature (210°F) and is lowered on a wire line commonly used for other instruments of the bottom-hole type at falling rates up to 500 ft per minute. It will detect gas flow as low as 10 ft per minute linear velocity, and yet withstand and record velocities of 1000 ft per minute without damage to the detecting element. Killing the well is not required nor desirable for running a production profile when using the instrument, and it is necessary to stop flow for only a short time. The detecting element of the instrument is a hot-wire anemometer connected in a

Jan 1, 1948

By William E. Ford, Edward Salisbury Dana

THIS Appendix contains a series of tables, more or leas complete, of minerals arranged according to chemical composition or to certain prominent crystallograhic or physical characters. These, it is believed, will be of service not only to the student, but ago to the skilled mineralogist. The type used in the printing of the mineral names indicates their relative importance. Table I is a complete list of the species named in this book arranged fist according to the prominent basic elements which they contain and secondly according to their acid radicals. Table II is of Minerals arranged according to their System of Crystallization The other tablets make no claim to completeness, being limited often to common ah important species. For an exhaustive system of Determinative Tables based particularly upon blowpipe and chemical characters, the student is referred to the work of Professors Brush and Pen- field, mentioned on p. 330.

Jan 1, 1922

By Oliver Bowles

ALTHOUGH Oliver Bowles retired as chief of the nonmetal economics division of the Bureau of Mines last year, that retirement has not lessened his active interest in the field of nonmetallic minerals, in writing, nor in his hobby, cultivation of African violets. Excellent co-ordination of the timing of a professional meeting and a flower show permitted him on at least one occasion to attend technical sessions and take in the African violet exhibition which happily arrived simultaneously in one city. Dr. Bowles celebrated his seventieth birthday on Jan. 10, 1947, and

Jan 1, 1948

By R. C. Mahon

Operators concerned with the destruction of their piping by acid mine waters will be interested in the method by which this problem was solved at the Cardiff mine of the Homer group. Rubber lined, or acid resisting metal pipes were found too expensive. Casting concrete lining in pipe would have required a minimum thickness of one inch, thus excessively reducing the pipe's diameter, as well as taking twenty four hours per length of pipe. The Naylor Pipe Co. of Chicago, having experimented with centrifugal lining of pipe with concrete, provided information which eventually solved the problem. An experimental plant was constructed as shown, and the following procedure developed : (1) Kerosene is used to remove the interior oil coating of new pipe. Closed with blank flanges, the pipe is revolved for eight minutes at varying speeds. Stopping and starting the motor achieves a good washing action. The kerosene is then drained off, and similar washing action with caustic soda removes any excess. Swabbing in done with burlap fastened to a 1/2-in. pipe. (2) The aggregate, made of one. part quick-setting cement and two

Jan 1, 1949

By AIME AIME

Council may deal with any matter of general interest, for which joint action of two or more of its member societies would have been appropriate, if Council had not been established. Council may initiate and carry through projects of the general character defined in the By-Laws, for which the necessary financial provision has been made. Council may take up, and in its discretion act upon, any matter of general interest referred to it by any member society or by any other society, national, state or local, or by any branch of Government, or by any individual or group of individuals.

Jan 1, 1920

By M. C. Leverett

Knowledge of the theory underlying the behavior of mixtures of fluids in reservoir rocks is essential to the proper solution of certain types of problems in petroleum production, but is as yet incompletely developed. The object of this paper is to show the application of well established thermody-namic and physical principles to these problems, and thus to assist in the development of the basic theory. For convenience the problems to be considered here may be divided into two groups: 1. Static problems, involving only the static balance between capillary forces and those due to the difference in densities of the fluids; i.e., gravitational forces. 2. Dynamic problems, involving analysis of the motion oi mixtures of immiscible fluids in porous media under the influence of forces due to gravity, capillarity, and an impressed external pressure differential. Capillary Equilbrium in Sands Under this heading the static type of problem will be discussed and the results of experimental investigations on the capillary properties of unconsolidated sands will be presented. Although the discussion of this section is, in a sense, prefatory to the treatment of problems of mixture flow, the concepts developed here have considerable intrinsic importance apart from their ap-plication to flow problems. For, it is reason-able to postulate that the reservoir fluids are, owing to their long existence in undis- turbed mutual contact prior to exploitation, in substantial equilibrium. It follows that their distribution in the reservoir at the time of tapping should be entirely predictable from the theory of capillary equi librium, provided certain experimentally measurable properties of the reservoir rock are known. Knowledge of the distribution of the several fluids in the reservoir is, ol course, helpful in the estimation of reserves and in other problems. It is to be emphasized that throughout the discussion of capillary statics it is assumed that the fluids are in equilibrium from the capillary standpoint. Thus, water, where it is referred to as being in a reservoir, will be understood to be interstitial water, present at the time of drilling the reservoir, commonly termed "connate" water. The theory developed here is perfectly general for any porous solid, whether a carefully prepared unconsolidated sand or a natural sandstone from an oil reservoir. At present, however, only problems involving clean, unconsolidated sands can be made to yield numerical solutions, since only such sands have been adequately investigated experimentally. Experimental evaluation of the pertinent properties 01 natural reservoir rocks will permit the extension of the numerical treatment to problems involving these materials. We shall now consider in some detail the static equilibrium of fluid mixtures in porous solids: that is, the manner in which the reservoir fluids are distributed vertically whell the Forces due to capillarity are just balanccd by those due to gravitation.

Jan 1, 1941

By J.W. Halley

The effects of tin on steel have become increasingly important because of the necessity of using poorly detinned scrap, tin cans, and terne plate, in the open hearth. Since a tin can contains about 1.5 per cent tin, it would be possible to have up to 0.75 per cent tin in steel made with a 50 per cent scrap charge. In order to use tin-containing scrap, it is necessary to know the effect of tin on various grades of steel. The following investigation is by no means comprehensive but covers a number of steels in which tin content is important. Published Work A number of investigations of the effects of tin on rolling quality and physical properties have been published. It has been found that tin increases strength and hardness and reduces ductility and notched impact resistance. The decrease' in ductility and notched impact resistance becomes more marked as the carbon decreases. McKimml found no change in Olsen ductility, Kockwell hardness, yield strength, tensile strength or elongation in cold-reduced strip containing up to 0.124 per cent tin. A tin content of 0.1j per cent gave difficulties in rolling and increased the hardness but 0.21 per cent tin showed no change in properties from material containing very little tin. No explanation of this contradiction is offered. Andrew and Peile2 investigated steels containing 0.10 to 0.25 per cent carbon and up to 0.63 per cent tin. They found an increase in tensile strength of from 100 to 200 lb. per sq. in. for each 0.01 per cent tin on normalized samples. The elongation and reduction of area were decreased and the notched impact resistance was reduced markedly. Quenched and drawn samples did not show embrittling if water-quenched from the draw temperature of 1148°F. (620°C.). They could find no evidence of tin under the microscope. Whitely and Braithwaite3 investigated the effect of tin on rail steel containing 0.55 to 0.60 per cent carbon. They found that 0.08 per cent tin caused a marked decrease in elongation, notched impact resistance and the degree of bend. The tensile strength was increased in some tests and not in others. Bolsover and Barraclough4 investigated the effect of tin up to 0. 50 per cent on a 0.35 per cent carbon steel and on several alloy steels with from 0.30 to 0.40 per cent carbon. They found a comparatively uniform decrease in notched impact resistance with increasing tin on quenched and drawn samples. If the samples were quenched from the drawing temperature or reheated to the drawing temperature and quenched, the embrittling was much less severe. Steels containing molybdenum suffered much less embrittlement than other steels. Experimental WoRk Effect of Tin on Low-carbon Rimmed Steel Increasing quantities of tin were added to four ingots of a heat of the following ladle analysis: carbon, 0.08 per cent; manganese, 0.39; phosphorus, 0.009; sulphur, 0.025.

Jan 1, 1943

By J. A. Hafford, J. K. Kerver, J. G. Richardson, P. M. Blair, J. S. Osoba

This paper presents the results of laboratory measurements of relative permeabilities to oil and gas on small core samples of reservoir rock by five methods, and describes the influences of such factors as boundary effect, hysteresis, and rate upon these measurements. The five methods used were the "Penn State," the "single core dynamic," the "gas drive," the "stationary liquid," and the "Hassler" techniques. In those methods in which the results are subject to error hecause of the boundary effect, the error may be minimized hy the use of high rates of flow. In order to avoid complexities introduced by hysteresis, it is necessary to approach each saturation unidirectionally. Observed deviations of relative permeabilities with rate can be explained as a manifestation of the boundary effect, and disappear as the boundary effect vanishes. The results indicate that all five methods yield essentially the same relative permeabilities to gas. Of the four methods applicable to the determination of relative permeability to oil, three, the Penn State, single core dynamic, and gas drive, gave relative permeabilities to oil which were in close agreement. The Hassler method gave relative permeabilities to oil which were consistently lower than the results obtained by the other methods. INTRODUCTION The relationship between the effective permeability of a reservoir rock to each of the fluids flowing through it and the corresponding fluid saturation is an important characteristic of the reservoir rock. Knowledge of this characteristic is and gas reservoirs and of the ultimate recovery to be expected extremely important in the prediction of the behavior of oil under various operating conditions. These effective permeabilities are usually expressed as the "relative permeability" to a fluid phase, defined as the ratio of the effective permeability to the permeability of the rock to a single phase at 100 per cent saturation. Relative permeability-saturation relations are not the same for all kinds of reservoir rock, but may vary from formation to formation, and within the different portions of a heterogeneous formation. In studying the performance of a specific reservoir, it is necessary, then, that the relative permeability characteristics of the individual portions of the reservoir be measured. These measurements may be made in the laboratory on small core samples from the reservoir. Various techniques have been proposed for the measurement in the laboratory of relative permeability-saturation relations. In varying degree, difficulties attend the use of all of the methods which have been proposed. It is the purpose of this paper to discuss the factors which influence the measurement of relative permeability, the difficulties encountered in several methods, and to present comparative results obtained by the use of various techniques. FACTORS WHICH INFLUENCE THE MEASUREMENT OF RELATIVE PERMEABILITY It is necessary that the relative permeability data measured in the laboratory yield the same relative permeability-saturation relationships that would govern the flow of fluids through the sample if it were to occupy its original position in the reservoir. Since the core sample upon which the laboratory measurements are made is not surrounded by similar core material as it was in the reservoir, an error in measuring the relative permeabilities may arise from the "boundary effect" which results from a discontinuity in capillary properties of the system at the effluent end of the core. Again, the rates of

Jan 1, 1951

By Dwight H. Seely, Louis R. Records

A process for low-temperature dehydration of natural gas utilizing Joule-Thomson effect in expansion through a throttling orifice has been tested in a full-scale field installation. The results of these tests are presented in the form of performance curves from which the process may be easily evaluated. The effect of separation temperature on condensate recovery from the process is also shown. INTRODUCTION The transportation of natural gas from producing well to the consumer has always encountered the problem of hydrate prevention. This problem has become increasingly important in the past ten years due to the rapid increase in produced gas volumes, production pressures, transportation pressures and distance from producing wells to consumer. Natural gas, as normally produced from gas or gas-condensate wells, is saturated with water vapor at well-head conditions of temuerature and pressure. The solution of the hydrate problem require; but one basic process — dehydration of the gas to a water content which will result in a water dew-point below the minimum temperature to be encountered from the producing well to the point of consumption. Much of the recent development of gas and gas-condensate reserves in the Gulf Coast Area has been in locations which are accessible only by water. High well-head pressures, pipeline construction and maintenance costs and the desirability of final central gas-condensate separation facilities have stimulated the development of dehydration equipment which can be installed at each well and which will permit hydrate-free transportation of both gas and condensate in the same line to central facilities. There are four types of natural gas dehydration processes now used: 1. Adsorptive processes. 2. Absorptive processes. 3. Chemical reaction processes. 4. Refrigeration processes. The first three of these processes are indirect in that they require use of adsorbents, absorbents or reactive chemicals. These materials require regeneration and part of the total gas stream is consumed in the regenerative process. Indirect processes have a wide range of flexibility as defined by allowable operating pressure and temperature, but most are not easily adapted to automatic operation. The refrigeration process described in this paper was designed for installation at the producing well-head. It requires no regenerative cycle and with normal well-head temperatures no external source of heat. The flexibility of this process is limited only by the pressure drop which may be allowed between well-head and transportation line. THEORY There are three basic physical concepts involved in the low temperature dehydration process. These are: 1. Formation of hydrocarbon hydrates. 2. Joule-Thompson effect resulting from the expansion of gaseous mixtures through a throttling orifice. 3. The equilibrium composition characteristics of water vapor and gaseous hydrocarbon mixture.. The chemical composition and physical structure of hydrate; have been described by several investigators.3,4,5,10 Specific conditions of temperature, pressure and composition as well as the requirements for turbulence and presence of free water necessary for hydrate formation have been described by Katz.6 Natural gas hydrates, as they are found in plugged gas pipe lines, have the appearance of packed snow. The mass of these hydrates has low continuous porosity and permeability. Joule-Thomson effect. or the reduction in temperature which occurs when natural gas is throttled throusll a restrictive orifice, is the basic phenomenon which permits efficient use of refrigeration for the purpose of dehydrating natural gas. Joule-Thomson coefficients for gafeous mixture; of methane with ethane and with butane have been reported by Buder.-I~olzer, Sage and Lacey.2 Brown1 predicted temperature drops for pressure drops from enthalpy-entropy calculations. Aside from this work there were no fundamental data found which would be applicable to natural gas mixtures of varying spe-

Jan 1, 1951

By H. H. Kaveler, W. R. Evans, Jack Tarner

The geological features, development history and engineering detail of the Shuler Field and the results of approximately two years of unitized operation of the Shuler Jones Sand Pool, were discussed in a prior publication.' The purpose of this paper is to present the results of pressure maintenance in the Shuler Jones Sand Pool after nine years of unit operation. GENERAL INFORMATION The Shuler Jones Sand Pool is located in and about Section 18, Township 18 South, Range 17 West, Union County, Ark. The pool was discovered .in September, 1937, unitized in February, 1941, and subjected to gas injection operations in July, 1941. Water was first returned to the reservoir in July, 1944. The reservoir is an anticlinal trap covering about 4,000 acres. The 154,000 acre-ft of sandstone initially consisted of approximately 150,000 acre-ft of productive oil zone and 4,000 acre-ft of gas-cap. The average depth of production is 7,400 ft. Maximum closure of the reservoir is 135 ft and the oil column lies between a gas-oil contact at -7,270 ft and a water-oil contact at -7,370 to -7,380 ft. The field is approximately four miles long. east and .west, and one and one-half miles wide. The sand grains are angular and vary from fine to medium size. The porosity of the sandstone averages 20.2 per cent. The specific permeability averages 400 md. Some zones have as high as 30 per cent porosity and specific permeability of 4,000 md. The reservoir rock is not uniform in character but consists of sandstone zones interspersed with shale. The variation in rock characteristics is evident in the electric log and core analyses presented in the original publication. Asphalt present in the pore space of the sandstone limited the reservoir to the southeast and apparently blocked any encroachment of water from that direction. The initial reservoir pressure at a subsea depth of 7,300 ft was 3,520 psi. The reservoir temperature was 198ºF. Initially, the solution gas volume was 765 cu ft per bbl and the reservoir volume factor was 1.45. The gas solubility and formation-volume-factors of the reservoir liquid are related with reservoir pressures above 300 psi as follows: Solution gas, cu ft per cu ft, S = 0.0334 P + 18.65 Formation volume factor of reservoir oil, FVF = 8.0 x 10 -5 P + 1.168 Gas volume factor, standard cu ft of gas equivalent to one cu ft of gas at reservoir conditions of temperature and pressure, F = .062 P - 4 Pressure (P) measured in psia. The equation for the gas volume factor presented above is based on a direct measurement of a sample of the gas and is a correction of that used in the original paper. The gravity of the oil produced is from 32 to 34" API. CALCULATION OF INITIAL OIL IN PLACE The Jones Sand production history is interesting because it lends itself to analysis by material balance. Production statistics from discovery of the Jones Sand through 1949 and material balance calculations of the initial stock tank oil in place are shown in Table I. The usual procedure in testing the application of material balance calculations is to compute the apparent initial volume of oil in place, using production and pressure information obtained at different time periods. If the apparent oil in place volumes computed increase with successive time periods, water encroachment is indicated and approximations must be mads to correct for its influence. The first requirement in utilizing such calculations is reliable reservoir pressure, accumulated gas, oil and water production, and PVT data. Calculations of apparent oil in place in the Jones Pool, based on field data

Jan 1, 1951

By A. M. Kivari

Operations at the cement plant of the Permanente Corporation, in the hills about 45 miles south of San Francisco and 12 miles west of San Jose, are interesting to the members because of the adoption of modern hydrometallurgical methods for handling and beneficiating raw materials. Closed-circuit grinding, classification, hy-droseparation, flotation, agitation, and thickening are familiar terms at this cement plant. These methods make it possible to process refractory limestone into suitable materials for the mallufacture of modern cements. Construction of the plant, having originally a design capacity of 7000 bbl. of cement per day, was started in June 1939, and the first clinker was ground on the following Christmas Day. At present the capacity is about 12,000 bbl. of finished cement per 24 hr., most of the production being low-heat cement. † About 3I30 tons of limestone, 620 tons of clay and I00 tons of gypsum are required daily for this output. Occasionally iron oxide is added to the clay to obtain the desired composition. This, together with the gypsum, is purchased from outside sources. up to the present time, the ccrporation has produced low-heat, normal, moderate-heat, moderate-sulphate-resisting, high-early-strength, oil-well, modihed-oil-well, and plastic cements. Most of the present production is for Shasta Dam, near Red- ding, Calif., the total demand being 5,800,000 bbl. of cement. Following are some of the cement require ments of the Shasta Dam specifications: Per Cent Chemical composition: Loss in ignition.......... 2.25 Insoluble residue......... 0.75 SO3.................... 2.25 MgO................... 5.'' Uncombined lime in clinker (CaO)......... I.25 Percentage of iron oxide to alumina ratio....... I.5 Compound composition: Tricalcium silicate (3CaO.SiO2)........... Not more than 35 Dicalcium silicate (zCaO.SiO2)........... Not less than 40 and not more than 65 Tricalcium aluminate (3CaO.Al2O3).......... Not more than 7 Tetracalcium aluminofcr- rite (4CaO.Al²O³.Fe²O³) Not more than 20 Fineness: The average specific surface in the bin sampled shall be not less than 1800 sq. cm. per gram and no individual sample less than 1600 sq. centimeters. Compressive strength: The average compressive strength in pounds per square inch of three mortar cubes composed of one part cement and 2.75 parts fine testing sand, by weight, shall be equal to or greater than the following:

Jan 1, 1942

By Erskine Ramsay

The following description of the Alabama coal-,fields is taken (with slight omissions) from the report " On the Warrior CoalField, by Henry McCalley, A.M., C. and M. E., Assistant State Geologist:" The coal lands of Alabama are of the great coal basin of the Ohio, or of the great Appalachian coal-field, and are estimated at 8660 square miles. They formed one connected field prior to the great Appalachian revolution, when there was pushed up through them long, narrow, anticlinal ridges which have been denuded into the present well-known anticlinal valleys, and thus this great field has been divided up into three more or less distinct parts. These parts were named by Prof. Tuomey, in 1849, the Warrior, the Cahaba and the Coosa coal-fields, respectively, from the names of the rivers which drain them. They are of very unequal size, the Warrior, with an area of 7810 square miles, being nearly ten times as large as the other two combined, and about two-thirds as large as the coal-area of Great Britain. This Warrior field is the most northwestern of the three coal-fields of Alabama, and comprises all of the coal-measnres in Alabama, northwest of the Alabama Great Southern railroad, or all of those drained by the Warrior and Tennessee rivers. The greater part of this field, almost all of it away from the present railroad lines, has never received more than a surface-examination. Still, we have in the Warrior coal-field one of the richest coal-basins of this or any other country. As a whole, the Warrior coal-field is a broad, shallow, tray-shaped depression, sloping towards the southwest, and with its southwest end covered by a newer formation and its southeast side, especially, complicated by folds and fractures. As is the case with all of our Coal Measures. it is composed of a series of sandstones. conglomerates, shales, slates and coal-seams, with some little limestone at several horizontal positions, but contains no thick bed of this last rock like the Measures of Pennsylvania and other States. The thickest conglomerates are near the bottom and top of the series, and hence these coals might be said to belong mainly to the

Jan 1, 1891

By Dwight H. Seely, Louis R. Records

A process for low-temperature dehydration of natural gas utilizing Joule-Thomson effect in expansion through a throttling orifice has been tested in a full-scale field installation. The results of these tests are presented in the form of performance curves from which the process may be easily evaluated. The effect of separation temperature on condensate recovery from the process is also shown. INTRODUCTION The transportation of natural gas from producing well to the consumer has always encountered the problem of hydrate prevention. This problem has become increasingly important in the past ten years due to the rapid increase in produced gas volumes, production pressures, transportation pressures and distance from producing wells to consumer. Natural gas, as normally produced from gas or gas-condensate wells, is saturated with water vapor at well-head conditions of temuerature and pressure. The solution of the hydrate problem require; but one basic process — dehydration of the gas to a water content which will result in a water dew-point below the minimum temperature to be encountered from the producing well to the point of consumption. Much of the recent development of gas and gas-condensate reserves in the Gulf Coast Area has been in locations which are accessible only by water. High well-head pressures, pipeline construction and maintenance costs and the desirability of final central gas-condensate separation facilities have stimulated the development of dehydration equipment which can be installed at each well and which will permit hydrate-free transportation of both gas and condensate in the same line to central facilities. There are four types of natural gas dehydration processes now used: 1. Adsorptive processes. 2. Absorptive processes. 3. Chemical reaction processes. 4. Refrigeration processes. The first three of these processes are indirect in that they require use of adsorbents, absorbents or reactive chemicals. These materials require regeneration and part of the total gas stream is consumed in the regenerative process. Indirect processes have a wide range of flexibility as defined by allowable operating pressure and temperature, but most are not easily adapted to automatic operation. The refrigeration process described in this paper was designed for installation at the producing well-head. It requires no regenerative cycle and with normal well-head temperatures no external source of heat. The flexibility of this process is limited only by the pressure drop which may be allowed between well-head and transportation line. THEORY There are three basic physical concepts involved in the low temperature dehydration process. These are: 1. Formation of hydrocarbon hydrates. 2. Joule-Thompson effect resulting from the expansion of gaseous mixtures through a throttling orifice. 3. The equilibrium composition characteristics of water vapor and gaseous hydrocarbon mixture.. The chemical composition and physical structure of hydrate; have been described by several investigators.3,4,5,10 Specific conditions of temperature, pressure and composition as well as the requirements for turbulence and presence of free water necessary for hydrate formation have been described by Katz.6 Natural gas hydrates, as they are found in plugged gas pipe lines, have the appearance of packed snow. The mass of these hydrates has low continuous porosity and permeability. Joule-Thomson effect. or the reduction in temperature which occurs when natural gas is throttled throusll a restrictive orifice, is the basic phenomenon which permits efficient use of refrigeration for the purpose of dehydrating natural gas. Joule-Thomson coefficients for gafeous mixture; of methane with ethane and with butane have been reported by Buder.-I~olzer, Sage and Lacey.2 Brown1 predicted temperature drops for pressure drops from enthalpy-entropy calculations. Aside from this work there were no fundamental data found which would be applicable to natural gas mixtures of varying spe-

Jan 1, 1951

By E. W. Newman

During 1943 and 1944, there was an urgent need for certain grades of optical calcite (Iceland spar) for instruments for ' military uses. To find a supply of this material, prospecting was carried out in Montana, California and Colorado. Although some production was obtained by the work in California, the best results were from prospecting the large calcite veins of south central Montana. The bulk of the optical calcite mind during World War II has come from that area. The Bureau of Mines took an active part in the search for optical calcite in Montana. It examined most of the known calcite veins in the 70-mile distance between Wilsall, on the Shields River: and Absarokee, on the Still water River, and conducted exploration on several of the deposits. The Geological Survey also took an active part by mapping many of the veins. Actual mining of the calcite was performed at first by Calcite Operators, Inc., and later by the Metals Reserve Co., through an agent. A sorting plant was established at Clyde Park, where custom material could be sold. These activities stimulated mining by private operators. To be suitable for military uses, the calcite mined had to meet rigid specificstions as to both size and quality. Individual crystals had to be clear and transparent and if in the form of rhombs had to measure at least 7/8 in. on each edge. Some color and a few inclusions in the calcite were allowable, but material with incipient or developed cleavages, or showing twinning other than parallel to the base, was unacceptable. History of Deposits The existence of large veins of calcite in south central Montana has long been known, and for many years the farmers of this region have used the common vein calcite for producing grit for chicken feed. According to reports, the fist optical calcite produced from Montana came from the Cartwright deposit near Grey-cliff,' but until recently the mining of optical calcite in Montana has been limited to spasmodic searching for small crystals suitable for making nicol prisms for saccharimeters and microscopes, or for mineral specimens. The possible need of substantial amounts of optical calcite for military uses began to appear late in 1942 and early in 1943, therefore the Polaroid company began searching for a source of supply in Montana and California. Work on the Wade property near Clyde Park was started on a small scale in the fall of 1942, by .4. H. Hansen, of Clyde Park. During the winter and spring of 1943, a modest quantity of optical calcite was mined and shipped to the Polaroid Corporation, Cambridge, Mass. Most of this was produced from the "Hansen vug," which was found close to the surface. Early in the summer of 1943, mining on the Wade property was undertaken by Calcite Operators, Inc., a company organized for mining optical calcite from the

Jan 1, 1948

By Y. Nakada, B. Chalmers

The work-hardening behavior of surface layers of aluminum and gold single crystals was investigated by alternately deforming and then removing a thin surface layer by electropolishing or by etching. Aluminum crystals exhibited lower flow stresses after the surface removal; gold crystals did not. Abrasion of surface eliminated easy glide in both gold and aluminum crystals. By alternately deforming and removing the surface layer, it was shown that the abraded crystals work-harden preferentially under the abraded layer. It is suggested that this phenomenon is caused by the difficulty of propagating dislocations through the abraded layer. It has been demonstrated in numerous cases'-3 that the plastic behavior of metals in either single-crystal or polycrystal form is sensitive to the environment and to the condition of the surface; it has also been reported4-6 that single crystals of some metals, when deformed in tension, exhibit more work hardening near the surface than in the interior. A third type of effect that has been attributed to the special part played by the surface in plastic deformation is the influence of the dimensions of the specimen on the various parameters that define its plastic-deformation characteris- tics.?-'' Many of these experiments were made on aluminum, on which an oxide film is always present under available experimental conditions; many of the effects have been attributed to the oxide film, either in terms of its higher elastic moduli, which would cause local stress redistribution, or its higher strength, which would oppose the escape of dislocations at the surface of the metal. On the other hand, it has been suggested II,12 that the mere presence of a surface should be sufficient to produce the observed results. A rigorous examination of this question could, in principle, be carried out by comparing the behavior of aluminum with its oxide film with that of the same material without oxide. This experiment would present great difficulties. The most practical alternative is to compare aluminum with gold, which has no crystalline surface film at room temperature, and to study the effects of various surface treatments on gold. The experiments described in this paper fall into two groups, the objectives of which were to determine 1) whether single crystals of gold shared the property of aluminum that the removal of a surface layer after some plastic deformation reduced the flow stress for further deformation and, since the result of this was negative, 2) whether a surface treatment could be found that caused gold to behave in this way. I) EXPERIMENTS AND RESULTS All the tests described below were carried out on single crystals of about 6 by 6 mm cross section and of sufficient length to provide a gage length of about 10 cm.

Jan 1, 1964

By S. T. Wlodek, John Wulff

Dense, adherent, and ductile coatings of chromium can be applied to Molybdenum by selectively freezing out the chromium solute from a supersaturated copper-or tin-rich liquid alloy. The successful exploitation of this technique depends on the control of variables common to any freezing process. Under the most favorable combimtion of supersaturation, nucleation, and mass-transfey, coatings as thick as 0.004 in. can be obtained. In exploratory experiments it was found that a coating of chromium may be applied to molybdenum by immersing the molybdenum body in a supercooled copper-chromium or tin-chromium melt and selectively freezing out the contained chromium onto the molybdenum body. Supercooling of the liquid metal plating bath can be achieved by cooling, or the maintenance of thermal or concentration gradients in the melt. The technique is similar to conventional dip-plating procedures where the sample is immersed in a molten bath of the pure plating medium, except that in these studies, the plating medium consisted of a dilute solution of chromium in liquid tin or copper. The success of this method requires that the base material to be plated be isomorphous with the coating and insoluble in the plating bath. In addition, the plating bath, while having an appreciable solubility for the coating component, must have negligible solid solubility in the solid plate. Such relationships exist in the molybdenum-chromium, chromium-tin, and chromium-copper systems. Liquid tin and copper are satisfactory as the plating solvent, because although chromium is appreciably soluble in both of these liquid metals, solid inter-solubility is almost negligible, and no compound formation occurs. The same relationships exist between molybdenum and copper or tin except that the solubility of molybdenum in liquid tin or copper is insignificant. It is this combination of solubility relationships, as well as the completely isomorphous nature of the molybdenum-chromium system, which allows the formation of a chromium coating on molybdenum by the selective freezing mechanism. Since the main deterrent to the widespread use of molybdenum for high-temperature structural applications is its poor oxidation resistance, the formation of a dense and ductile chromium coating on molybdenum may well be of commercial significance. In addition, the basic principle of coating formation by selective freezing should be applicable to other metallic or even nonmetallic systems. The precipitation of the solute from a liquid metallic solution, for the formation of a protective coating, has not been previously considered in the literature. Frequently, however, a similar phenomenon has been described in the corrosion of metallic heat exchangers by liquid metals1 wherein temperature gradients in the liquid metal heat-transfer medium result in the formation of layers or deposits of metallic residue2 in the cooler portions of the system. Impregnating techniques using liquid baths have been tried as a plating process. Semchyshen and Barr, for instance, have successfully diffused chromium into molybdenum by immersing the molybdenum specimen in a liquid tin-chromium or copper-chromium alloy. This simple holding technique fails to produce a layer of pure chromium and requires prolonged immersion to allow for the diffusion-activated enrichment of the molybdenum. During the course of this investigation, most of the phase relations published for the copper-chromium4 and molybdenum-chromium4 systems, were found reliable. It was necessary, however, to investigate the solubilities of chromium and molybdenum in liquid tin as well as the solubility of molybdenum in liquid copper. These determinations were made by a simpie weight loss technique on materials of the same purity as used in the plating studies. The results of these solubility studies are given in Tables I and I1 and indicate that although the solubility of molybdenum in liquid

Jan 1, 1961

By H. I. Najarian

This paper is a companion piece to the description of the electrothermic process that begins on page 141. It will be confined to a brief story of the development. of the Weaton-Najarian vacuum condenserf at this plant, together with up-to-date design and operating data. The Josephtown smelter was designed primarily for production of zinc oxide. However, the development of a method for production of zinc metal had always been under consideration, and accordingly one of the original eight units of the elcctro-thermic furnaces built in 1930 was set up to produce metal. The design of this furnace was identical with that of the oxide furnaces except that in place of oxide tewels opening into oxide manifolds, conventional conical clay condensers—similar to condensers used in horizontal retort smelting—were installed around the periphery of the furnace and in several tiers vertically for condensing the zinc vapors. The early experimental work in trying to condense zinc out of the mixtures of zinc vapor and carbon monoxide gas from the electrothermic furnaces indicated that, while the gases from electrothermic smelting would condense in surface-type condensers, the formation of blue powder was excessive and condenser efficiency low. Furthermore, operating a large unit of electric furnace with several hundred small condensers, with attendant high labor cost and unfavorable operating conditions, did not appeal to us. We also realized that a single unit of surface condenser capable of condensing 12 torg tons of metal per day would be of huge dimensions and possibly difficult of control. So we took as our aim the development of a method whereby a single condenser unit of reasonable dimensions would condense zinc, in one step, from the large volume of gases that the electric furnaces produced. We set about searching for knowledge on zinc metallurgy and design of zinc condensers in particular. Our study of the prior art focused our attention on the oft-repeated statement by earlier experimenters, that the most efficient way to condense metallic vapors, such as zinc vapors, was to bring the vapors into "intimate contact" with molten metal; but the methods offered for securing this "intimate contact" in any practical manner left much to the imagination. We were handicapped by not having some-one on the Josephtown smelter staff who could lay claim to being an expert zinc metallurgist and could give guidance from actual experience on the practicability of various schemes that haunted our imagination. Laboratory Experiments However, we had an expert ex-steam engineer in the person of George I?. Weaton, manager of the Josephtown smelter, who had had long experience with steam-jet condensers and would reiterate his belief at every opportunity that the logical and the most efficient way to condense zinc would be with a jet-type condenser. We became intrigued by the possibilities of a zinc con-

Jan 1, 1944