Search Documents

By N. Mao

This paper presents the results of a research effort to develop a technique for estimating in situ stresses by measuring stress-induced velocity anisotropy around a borehole. Relevant parameters required to make the estimate were identified and measured in the laboratory on a 35.6 cm (14.0 in) cube of Nugget sandstone with a 10.2 cm (4.0 in) diameter hole, under biaxial loading. Two pairs each of radially and tangentially polarized transducers were placed inside the hole with displacement directions either parallel or perpendicular to the principal stress directions. With this configuration, relative travel times were measured by both a pulsed phaselocked loop technique and a cross correlation of digitized waveforms. The biaxial velocity data were used to back-calculate the applied stress. The standard deviation of the differences between the calculated and applied stresses is 0.62 MPa (90 psi) for a stress level up to 8.63 MPa (1250 psi).

Jan 1, 1984

By William Braden

This paper is presented in the hope that it will be instructive in view of the future large expansion of the mining industry in the west-coast countries of South America. There is a more or less general impression that the Spanish-American workman is inferior to the American, but after some years of experience and observation I doubt the correctne~s of this view. Taking into consideration all the elements which make for efficiency of labor, it has been found, particularly in Chile, that under proper organization native labor yields as much, man for man, and more, dollar for dollar, than in the Western United States. If a manager is willing to accept unreservedly the costum-bres del pais, without combating intelligently and patiently the ones tending to inefficiency, he should expect no better results than he deserves. He must conscientiously insist that a " square deal" be given and exacted; that liquor be excluded from camp as far as possible; that comfortable quarters and other uplifting elements of life be provided; and that past and existing methods and customs shall not be over-ridden rough-

Jan 1, 1910

US 4,183,899 - Flow process for chlorinating ilmenite. A laminar flow of a mixture of ore, a carbonaceous reductant, and chlorine gas or other chlorinating agent is passed through a reaction zone maintained at a temperature of 1350 to 1950°C and a product stream Including titanium tetrachloride is withdrawn from the zone. The atomic ratio of carbon to oxygen in the feed mixture is greater than 1:1, and the molar ratio of chlorine to titanium solids In the product stream is between about 0 5.1 and 2:l. Titanium chlorides and metallic iron are recovered separately from the product stream. J.P. Bonsack, assigned to SCM Corp, Jan. 15, 1980 21 pp. (423-79). Filed. 3-10-78 (885,442).

Jan 1, 1982

By ir. H. Eraly

At the Zolder mine a S/7 computer is used for two purposes : - to monitor production at the coal face - to monitor the distribution of mine cars. By using sensors attached to equipment at the coal face and at the loading points, the computer provides realtime information and also summarized reports, which help management to control production better. The computer will display this information to the control room, where two operators monitor all production events and the availability of the right numbers of mine cars at every production face. All benefits obtained from the system are described.

Jan 1, 1977

By Sanjoy Shome

Recent legislation and the heightened environmental awareness of the public have brought about constraints in the location, process selection and operation of the modern electrolytic refinery. The modern electrolytic zinc process incorporating pyro, hydro, and electrometallurgy has emissions, effluents and residues which are acceptable only under severely restricted discharge conditions. Due to the necessity of maximizing zinc recovery, the additional cost of the environmental equipment has to be minimized, which may be achieved by intelligent process and location selection as well as by proper operation of the plant for maximum return to the Owner and minimum damage to the environment.

Jan 1, 1977

By George J. Conroy, James H. Green

Results of a long-term program of electrical parameter measurement in underground coal mine working sections, performed by The Pennsylvania State University under US Bureau of Mines (USBM) sponsorship, are utilized as the basis for an analysis of the electrical energy requirements during operation. A model section is hypothesized, developed from the average or most representative characteristics as determined from tabulations of the measurements. Performance factors of the model section's machine complement are then analyzed, particularly with regard to the energy required per ton of raw coal cut and delivered from the section. Results are given in kilowatt -hours per ton.

Jan 1, 1980

By M. L. Jeremic

Observations of ground behavior in mining the Choka Dulkan ore body have been described. Ore recovery was limited to approximately 60% because unconsolidated hydraulic fill did not permit either the widening of stope spans nor secondary ore recovery from pillars. Stope undercutting induced high stress concentrations. However, as extraction progressed, ground conditions improved but before extraction was complete they deteriorated again. After completion of a stope, the remnant rib and crown pillars continued to be deformed by other stresses for some time.

Jan 1, 1979

EDWIN M. CHANCE (communication to the Secretary?).-The subject of miners' lamps. has long interested me and it would seem that the thought that has been given to it by the Bureau of Mines, and the users

Jan 6, 1917

By Ben B. Cox

Oil produced in Iraq for export during 1938 was 31,354,090 bbl., or a daily average of 85,901 bbl; This is an increase of 182,614 bbl., or 0.5 per cent over 1937. All oil exported was produced from the Kirkuk field. The Khanaqin Oil Company, Ltd., a subsidiary of the Anglo-Iranian Oil Company, Ltd., continued to supply local market requirements from its Naft Khaneh field in the Transferred Territories. Slightly more than 32,000,000 bbl. was produced in Iraq, a small part of which was used in field operations. During the year 12 wells were completed and 9 wells were drilling at the end of the year. Of the completions, 5 were producers and 1 was an oil-water level observation well in proved fields, and 6 were listed as failures. Basrah Concession The outstanding event of the year was the granting, by the Kingdom of Iraq, of a 75-year concession embracing approximately 89,000 sq. miles to the Basrah Petroleum Company, Ltd., a British company with French and American participation. The concession covers all parts of the Kingdom, its territorial waters, islands, submerged lands, and its interest in the Neutral Zone separating Iraq and Saudi Arabia that

Jan 1, 1939

Jan 1, 1935

By Mario L. Villa

Oil activities and the petroleum industry in general have suffered severely in this country as a result of present war conditions. War has imposed a very heavy and unpleasant burden on the shoulders of those whose duty it is to keep .Argentina supplied with the necessary oil to meet industry's growing demands. Since 1940, imports of manufactured products from Europe and the United States have fallen to a minimum, making it necessary to manufacture as many of them as possible locally. This has brought about the establishment of many new industries and the enlargement of already existing plants, creating new demands for fuel that drain heavily the country's stocks, which already were overtaxed because of the diminished supply imported. To cope with this problem, a plan for an intensification of oil-field activities was drawn up by Yacimientos Petroliferos Fiscales (Argentine Government Oil Fields) which included the drilling of many new

Jan 1, 1943

By David G. Chedgy

The Meadow River No. 1 preparation plant, owned by Sewell Coal Co. which is a subsidiary of the Pittston Co., was commissioned in the spring of 1974. A survey of the environmental noise levels was conducted, and the dominant noise sources identified. An engineering program was initiated to reduce the prevailing levels to a point that the operator's exposure would be within compliance with the MESA regulation for ear protection. The program was continued until compliance was achieved and the attenuation factors for each abatement device recorded. The highlights of this program will be presented with a discussion of the practicality of the devices utilized.

Jan 1, 1977

By R. E. Sabaski

Total grinding mill system life is dependent upon the original selections and specifications of its components: the mill, its drive, drive motor, motor control, and power system. This paper discusses the complex considerations involved and the critical decisions which must be made by the buyer, the mill manufacturer, and by the gear vendor during the proposal and ordering stages. Interrelations between the mill manufacturer and the gear vendor, application of ACMA standards, how drive standards and specifications are refined through steady-state and computer-simulated torsional analyses are included, along with correlational field testing, as demands for larger sizes challenge the current state of the art.

Jan 1, 1984

By Robert Mehl

THE system cadmium-mercury has attracted much attention, chiefly because of its importance in the study of electrochemical standard cells. The constitutional diagram, as it is accepted today, is essentially that FIG. 1.-BIJL'S DIAGRAM FOR CADMIUM-MERCURY ALLOYS. developed by Bijl1 (Fig. 1), though there has been a great amount of work done on the system by other workers.2 A year ago the senior author published a paper on the crystal structure of the system, in which were described determinations of crystal structure

Jan 1, 1929

By C. Le Neve Foster

The object of this paper is to offer a few suggestions for improving the mining and mineral statistics presented by the governments of various nations on both sides of the Atlantic. At the present time one may fairly complain of' two evils—lack of uniformity in some cases and want of completeness in others. The consequence is that the statistics are either less plain than they might be, or are useless for comparisons, or fail to present a faithful picture of the state of the mining industries of a country. The principal subjects upon which information is desirable are: the amount and value of the mineral products raised and the number of the mining population. With these data it is possible to form an estimate of the importance of the mining industries of any given

Jan 1, 1894

By Benjamin C. Koskiniemi

Introduction When evaluating any ore body, one of the first questions concerns the ore reserves. In the case of an open pit mine, this is not possible to answer reliably until the ultimate (final) pit limits have been established. Techniques used in designing an ultimate pit are classed as (1) manual, (2) computer, and (3) combined manual-computer. This chapter will describe how manual techniques can be utilized in designing an ulti¬mate pit Certain economic and design criteria must be established before the actual design begins In order to begin designing an ultimate pit, it will be assumed that the engineer already has the following data available (1) vertical sections, (2) horizontal sections for each level, (3) stripping curve, (4) bench height, (5) bank slope angle between levels, (6) level berm width, (7) roadway width, (8) pit slope angles at ultimate pit limits (estimated average including roads and ramps and between roads and ramps), and (9) minimum width of pit bottom

Jan 1, 1979

By Joseph G. Wargo

An investigation of trends in exploration expenditures for a selected group of mining companies was undertaken for the interval 1968-1971. These trends were compared with financial factors that are associated with various groups of companies and the implications of these trends are indicated. The sample consists of 21 mining companies, of these, 19 are listed on the New York Stock Exchange and 2 are listed on the American Exchange. Twenty are American, one is Canadian. All are fundamentally "mining companies" in that they derive the bulk of their income from the ex- traction, sale, and at times, fabrication of metals from their own mines. This is in contrast to companies which have mineral exploration departments but derive the bulk of their revenues from sources other than mining, such as oil and gas sales. No companies which can be considered strictly as exploration companies are included in the sample. This definition held up in 1968, however, its strict application became more difficult through the years. In 1971, three or four of the companies were changing their character in that they were phasing out of the mining business and deriving a substantial part of their income from activities other than mining.

Jan 5, 1973

By Gloyd M. Wiles

Since D. C. Jackling was famous for his adeptness at organizing and training teams of operating personnel, the subject of mine management is particularly appropriate for a Jackling Lecture. In fact, it is doubly appropriate because in very basic ways Jackling's career changed the nature of the tasks and challenges facing a mine manager. Management of mines, of course, is the art of finding and winning minerals economically from the earth's crust, and it involves the use of all the engineering sciences. But also of prime importance is a skill which is not yet a science-the area of management often referred to as human engineering. Since expenditures on staff and labor may well involve more than 50% of the direct costs of operating a mine, ability at human engineering is just as important as the ability to plan and put into effect the most efficient operating procedures.

Jan 5, 1962

By John B. Farish

This brief paper is designed to place on record some interesting occurrences, recently observed during an examination of the Golden Age Mine, in Boulder county, Colorado. Leaving the little village of Jamestown—or Jimtown, as it is more generally called—located in the canon of James creek, the road winds up a steep mountain composed of the coarse gray granite, with occasional belts of gneiss, common to all the mineral-bearing sections of Boulder county, to the summit of the front range of the Continental Divide. Here are located the mines known as the Golden Age and the Sentinel, the relative locations of which are shown in Fig. 1. The Golden Age location covers the outcrop of a quartz-porphyry dike, which cuts through the granite country-rock with a strike of about N. 70' E. This dike varies in width from a few feet, as at a point between the main shaft and the Hill shaft, to about 50 feet,

Jan 1, 1891

By J. E. Lawver, W. D. Carrier

During the past 20 years, millions of dollars in research effort have been spent to improve methods of phosphate clay dewatering and disposal. Although to date no proven large-scale system has been developed that will result in ultimate below ground storage without the use of at least temporary dams, considerable progress has been made and a variety of techniques are being tested, some on a large scale. This paper summarizes the use of mathematical and centrifuge (physical) models that can analyze and evaluate various systems for the consolidation of phosphatic clays. These provide a powerful tool for engineers responsible for land management and mining waste disposal.

Jan 1, 1985