Search Documents

By David B. Reger

The value of carbon ratios in determining the boundaries of possible oil deposits appears to have passed the hypothetical stage. The theory that the ratio of fixed carbon in pure coals is an invariable index of incipient metamorphism in both surface and underground rocks and that it may be applied in defining the limits of petroleum, advanced by David White,' has been received with keen interest by many petroleum geologists. Detailed isocarb maps have been prepared of the Pennsylvanian area of North Texas and Eastern Oklahoma by M. L. Fuller.² A similar map of the coal-bearing area of West Virginia is given here. An isocarb3 is a line showing an equal fixed-carbon percentage, pure coal basis; the term has been proposed by David White to supersede a less expressive nomenclature. The term carbon ratio is applied to the pereentage of carbon in pure coal after water and ash have been eliminated. As a comparatively small number of analyses have been made on this basis, it is usually necessary to compute the ratio by dividing the fixed carbon of the proximate analysis by the sum of the fixed carbon and volatile matter of the same analysis. Many thousands of proximate analyses have been made by the West Virginia Geological Survey, covering nearly every county in which coal is found. Numerous others have been made by the U. S. Geological Survey and the U. S. Bureau of Mines, but as uniformity of results is best secured by adhering to one set of analyses, the tests of the West Virginia Survey have been cxclusively used.

Jan 1, 1921

By R. J. Mechin

IN the early part of 1934, the St. Joseph Lead Co. purchased from the Kadco Corporation three dust-removal units, two suitable for raise work, and the other for drifting operations. The equipment was installed at the Balmat mine, in St. Lawrence County, New York. The Kadco dust-control system can be briefly described as one in which hoods, through which the drill steel is drawn, control the dust at the drill hole, the dust is conveyed through rubber hose or pipe to a collector, where it is removed from the air stream, and the air is then available for recircula-tion in the working place. As during the last few years a number of studies had been completed for the purpose of determining whether or not the dust was effectively removed by the Kadco system, and as the dust counts taken in these tests apparently indicate that it was, the St. Joseph Lead Co. was only inter-ested in obtaining data to show the efficiency of drilling, expressed in terms of minutes per foot drilled, when -using Kadco equipment, in comparison with the former method of drilling dry in a raise and drilling wet in a drift. Comparative dust counts were taken at Balmat, however, by the Metropolitan Life Insurance Co. to show the difference in the dust content of the air in which the operators worked when drilling dry, wet, or with the Kadco equipment.

Jan 1, 1935

By William R. Rumbold

When I was in South Africa during the latter part of 1904, there were three known tin-fields, which may be called the Cape Town, the Bushveld, and the Swaziland fields. The Cape Town Tin-Field. This district is situated near Kuils river, 20 miles west of Cape Town, and 5 miles from Kuils River station on the Cape Town & Stellenbosch railway. The deposits are in granite, intrusive in the Malmesbury beds, which are supposed to be of Silurian or Cambrian age. The granite, resisting denudation better than the surrounding shales, has formed low-lying hills, the highest of which, the Bottlelary Berg, is 1,510 ft. above sea-level. The rock consists of quartz, orthoclase feldspar, and biotite mica; tourmaline is also present. The feldspar occurs in large crystals. The rock is generally decomposed on the surface, and the decomposition sometimes extends as deep as 100 ft. This formation—granite intrusive in Silurian shales— extends for many miles to the northeast, but so far as I know the Kuils River deposits are the only ones now known to occur in it, though probably further prospecting will reveal other deposits. This particular discovery was accidental; alluvial tin being found in the course of boring for oil. The Kuils River Deposit. This deposit comprises both lode and alluvial tin. The lode strikes N-S., and dips about 30' E. into the hill. It is 5 ft. wide, and composed of dense white quartz, in which pinkish-gray cassiterite is distributed in large crystals. The vein also contains considerable quantities of wolframite. Fig. 1 is a rough plan of the relative positions of the lode and the alluvial deposit, the latter, as shown, following the course of a stream, while the lode crops out on the hillside ,

Jan 1, 1909

By John Pew

PRIOR to the development of the bulk-oil carrier, practically all transportation of oil was in barrels and in cans contained in wooden cases; the latter was known as case oil. In the year 1885, approximately two hundred million gallons of petroleum were exported from this country in barrels and about one and three-quarter millions in bulk; less than twelve years later, the shipment in barrels had decreased to nearly one and three-quarter million gallons, while the transport of bulk oil had increased to four hundred eighty-four million gallons. The first modern tanker, the "Glückauf," was built in England in 1886. Her hull, which was 300 ft. long, was divided into compartments by transverse bulk-heads, these compartments being divided by longitu-dinal center-line bulkheads extending throughout the oil spaces. There was a pump room forward of the boiler room, thus providing a cofferdam or safety space. Between the main and upper decks, a narrow trunk extended the full length of the' oil spaces, the trans-verse and longitudinal bulkheads being carried to the upper deck. This allowed for the expansion of the oil from a rise in temperature, and if the tank below the main deck was kept full, the danger of the oil moving with the roll and pitch of the vessel was considerably reduced. Spaces for the carriage of light oil were provided on each side of the vessel outboard of the expansion trunk, while water ballast was carried under the machinery compartments fore and aft. Although vessels previously had been built to carry oil next to the skin of the ship, it is claimed that the "Glückauf" was the first one constructed on the new principle outlined.

Jan 12, 1922

By Leo Dana

INTRODUCTION THE object of this paper is to discuss the factors and conditions that affect the observed values of the melting points of refractory materials and to describe practical methods for the determination of these points. While it appeared to be necessary to discuss some of the general properties of silicates and refractories, these subjects have been entered into only in so far as they relate to the melting point and its determination. Refractory materials such as fireclays, firebricks, and minerals generally, may be considered to be composed of compounds of metallic oxides, solid solutions of the oxides, the pure oxides, or mixtures of the three classes together with small amounts of a variety of chemical compounds. The oxides of silica and alumina occur most commonly in refractory materials; in combination with. these, oxides of the alkali earth, the alkali, the iron group, and the rare earth metals are frequently found.

Jan 9, 1919

By J. S. Jacobi

Treating copper ores by heap-leaching and similar hydrometallurgical means is a time-honored practice, which was well known even in the 19th century. Later the method lost ground to better ore dressing processes, particularly selective. flotation. More recently there has been a distinct reversion to leaching techniques, particularly for scavenging operations in old mining stopes, in connection with LPF systems, irrigation of tailings dumps and similar situations. These hydrometallurgical techniques will gain further ground because processing is simple and permits better extraction of copper, particularly from low-grade or partly oxidized ores. In the lixiviation of primary ores at some major operations, copper-bearing liquors may undergo re-circulation in heap-leaching arrangements or the ores may be subjected to systematic percolation treatment. The liquors resulting from this source usually are quite strong (above 10 gpl copper) and copper would normally be reclaimed by electrowinning or cementation. These processes fall out- side the scope of this paper which is concerned with recovery of copper from weak 1iquor.s containing from 0.1 to about 3 gpl copper.

Jan 9, 1963

By Paul Weir

Bleaching clays have been used extensively in the oil-refining industries for a number of years. Their use in water purification is relatively recent and less extensive. They are frequently classified as (1) those naturally active and (2) those active after artificial activation with acid. Fuller's earths fall within the general group of bleaching clays and gradually the commercial term "fuller's earth" has been applied to natural clays originating, for the most part, in the southeastern section of the United States. Bentonitic clays are usually classed as activable and are prevalent in the southwestern section of the United States.l Bleaching clays vary considerably in chemical and physical properties throughout the country, or even in different parts of one deposit (Table 1). The fuller's earth type of clay is characterized by a lack of plasticity, relatively adsorbent, foliated structure, and does not swell to form a

Jan 1, 1942

By Jos D. Weeks

On the extreme fringe of' the great Appalachian coal-basin is a long narrow detached coal-field, which is, in some respects, one of the most important in the United States. This field, about 90 miles long by 2½ to 16 miles wide, extends from the southwest corner of Somerset county, Pennsylvania, through Allegany and Garrett counties, Maryland, Mineral, Grant and Tucker counties, West Virginia, into Randolph county, West Virginia. In this distance four distinct sub-districts are recognized, the Wellersburg in Pennsylvania, the Cumberland-Georges creek in Maryland, and the Elk Garden and the Upper Potomac in West Virginia. The output of coal from the whole field including steam, domestic, smithing and coking-coal of the best quality, is about 4,500,000 tons annually. It is the nearest to tide-water of all the bituminous coal-fields which supply the great coal-markets of the Northern Atlantic seaboard ;

Jan 1, 1895

By C. Willard Hayes

One of the most productive iron-ore districts of the southern Appalachians lies in the vicinity of Cartersville, in northwestern Georgia, where the ore-deposits are so directly related to the stratigraphic and structural features of the region that a description of its geology possesses economic as well as scientific interest. Stratigraphy.—The area shown on the accompanying map, Fig. 1, occupies the southeastern portion of Bartow county, Georgia. It is about equally divided between the older crystalline and metamorphic rocks which occupy the Piedmont plateau and Appalachian mountains on the east, and the Paleozoic formations which occupy the Appalachian valley on the west. The line separating these two groups of formations enters the mapped area near the northeastern corner, and, pursuing a somewhat irregular diagonal course, leaves it, as shown on the map, near the southwestern corner. This line marks

Jan 1, 1901

By John E. Dowis

Ore distribution being what it is, many of today's mining companies are forced to develop foreign reserves to satisfy the demands of their customers. This necessity complicates the economic picture for a company, because management must look well be- yond grade and tonnage to determine the feasibility of developing a foreign orebody. Above all, the taxes on such a development must be assessed. The difference that taxes can make in mining profits will be illustrated here for three countries-Canada, Mexico and the United States. For purposes of comparison, identical orebodies will be assumed to occur in all three countries. Only the taxes on these properties will vary. Grade, tonnage, gross income, production costs and production rates will all be the same. The discussion will be limited to federal taxes, because state and provincial taxes are usually negligible by comparison. Assumptions relative to the orebody and the nature of the company undertaking the operation are as follows: (1) Copper is the only value to be recovered. (2) Sixty million tons of ore have been delineated. (3) Underground mining is required, and the production rate will be 3 million tpy. (4) The life of the property is 20 yr. (5) Operations in Mexico or Canada will be handled by a subsidiary of a U.S. parent company. (6) The subsidiary will offer stock.

Jan 1, 1970

By E. C. Wright

FOR many years the cost of making pig iron and steel in the Birmingham district has been about the lowest in the United States. The close proximity of the important raw materials such as coal, iron ore, limestone, and the large available scrap supply made it possible to assemble all of the important ingredients necessary for steel-making with only nominal costs for transportation. Both iron ore and coal were being mined in this district at one time for about $1 per ton from underground operations. At that time mining wages were low everywhere and the labor rate in the South was considerably below that of other mining districts. This situation persisted until the emergence of labor unions as an economic and political force, emigation of southern labor to northern plants, and continued growth of industry in the South in the years following the depression of 1932. Since that time union organizing of miners and steel workers throughout the nation has increased labor costs in mining and steelmaking. This influence has been felt particularly in underground mining operations since the proportion of labor cost to total cost is still high. The previous advantage in basic labor rate in the South has been almost entirely eliminated by the equalization of labor rates in basic industries by national unions.

Jan 12, 1950

By William G. Pariseau

A plasticity theory for anisotropic geologic media has been applied to the problem of quasi-static wedge penetration of rock under confining pressure. Numerical evaluation of the governing system of stress equations in the transversely isotropic and orthotropic cases using representative material properties shows that the consequences of initial anisotropy for the penetration process are by no means trivial. In the transversely isotropic case, a threefold increase in the vertical force required for penetration to a unit depth occurs as the inclination of the axes of anisotropy are rotated through 90° with respect to the penetration path. The horizontal force required varies from zero to a maximum at approximately 60° then back to zero as the axes of anisotropy are rotated. The maximum is of the order of magnitude of the force required in the isotropic case. Similar results are observed in the orthotropic case. Practical aspects of the post-elastic phenomena associated with anisotropic rock indentation within the context of drilling problems include: bit yaw, hole deviation and bending stresses in the drill rod, all of which vary with strata dip but which can be quantitatively evaluated given the bit geometry, interface friction and rock properties. In a broader context, the analysis reveals the necessity for well conceived experimental work and sound theoretical research concerning post-elastic behavior of geologic media as a function of confining pressure, the effects of induced anisotropy, and the variation of strength parameters with loading path changes in the post-elastic range.

Jan 1, 1971

By L. M. Johnson, C. G. Janes

INTRODUCTION In May, 1966, the General Services Administration (GSA) announced a program to encourage additional domestic production of copper in the interest of national security. Upon learning of the copper production expansion program, Duval Corporation entered into negotiations with GSA for development of the Sierrita copper-molybdenum property under the program. Agreements between the GSA and Duval Sierrita Corporation, a wholly owned subsidiary of Duval Corporation, were concluded in 1967, with the Sierrita Concentrator beginning operation in 1970 at a designed capacity of 72,000 STPD. Subsequent additions and modifications have expanded capacity to 90,000 STPD. This property, located approximately 20 miles south of Tucson, Arizona, represents an investment including working capital of about $200 million. These funds were provided from an $83 million loan from GSA, repayable in copper valued at 38 cents per pound, $48.75 million of bank loans subject to U. S. Government V-loan guarantees, and Company capital contributions. Current general operating statistics for the concentrator are listed below: [Ore Grade 0.32% Cu., 0.030"/. Mo. Daily Tons Milled 90,000 STPD Annual Copper Product ion 94,600 Tons Annual Molybdenum Production 15,000,000 Lbs. Annual Silver Production 1,135,000 Ounces]

Jan 1, 1976

By G. W. Tracy, R. D. Carter

A method based on an approach by Hurst' is developed for calculating water influx behavior. Using this method, superposition calculations may be eliminated. The principal diflerence between this method and that of Hurst is that, over finite intervals of time, constant oil-productton rates are assumed by Hurst whereas constant water influx rates are assumed in the presently described method. By adopting the assumption of constant water influx rate for finite time periods, a method is developed for calculating water influx behavior which lends itself to convenient combination with the material balance equation in the Schilthuis form. Above the bubble point, an equation is given for the explicit step-wise calculation of pressure history for a prescribed oil-production history. Use of this method of calculating water influx behavior should result in a considerable saving of time as compared to superposition calculations when the calculations must be made without using a digital computer. The connection is shown between the method described herein and the method developed by van Ever-dingen and Hursr2 (which requires superposition cal-culations). Also, results obtained using the two methods are compared.

By R. K. Adams

The availability of digital computers costing less than $15, 000 makes them economically attractive as versatile research and experiment tools. Several such installations at Oak Ridge National Laboratory have shown that improvements in research productivity and experimental control accuracy can result from the proper application of a small digital computer. However, careful attention must be paid to several potentially expensive problems in 1) interfacing the experiment to the computer and 2) programming the computer. Two specific applications of very small computers to metallurgical testing and research are described. One is a system for data acquisition and precise temperature control associated with a thermocouple testing program, and the other is a system for pulse calorimetry determination of the specific heat of metals over wide temperature ranges and in the neighborhood of metallurgical transformations. The data acquisition system which uses a PDP-8/S computer monitors signals from up to 264 low-level thermocouple signals at two scanning speeds: 10 readings per second for long-term drift data, and 500 readings per second for transient data. The pulse calorimetry system which uses a PDP-8 computer accepts up to 6 signals of 0- to 10-v range and because of a larger analysis program, uses a bulk memory (magnetic disc) in addition to core memory.

Jan 1, 1969

By J. M. Johns

INTRODUCTION The Climax Mine is located on the continen¬tal divide, on Fremont Pass, about 145 Km south west of Denver, Colorado. Molybdenum, along with the by products, tungsten, tin, and pyrite are produced from both the open pit and under¬ground operations. The underground operation utilizes a panel caving mining system, and produces in excess of 27,000 mt per day. In the mid 1930's, the Climax mine began changing from a grizzly level layout to the slusher drift system which is still in use to¬ day. Over the years, the slusher drift layout has been refined to correct, improve, and sim¬plify minor operational problems. In common with most older hardrock mines, the development equipment used at Climax was the standard rail mounted, pneumatic mining machinery. This type of equipment remained in use, at least to some degree, until about four years ago. For production, 112 Kw electric slushers were used, while mine traffic was rail with trolley locomotives. Beginning about ten years ago, Climax began

Jan 1, 1981

By G. W. R. Kuzyk, John D. Smith

Tantalum Mining Corporation of Canada Limited has been mining tantalum ore from the Bernic Lake pegmatite dyke since 1968. The shallow nature of the dyke and relatively high strengths of the various rock types led to the choice of a room and pillar mining method. Rock mechanic studies have indicated that the original pillar dimensions of 50 feet x 50 feet are conservative for existing rooms. Therefore, a plan to reduce the size of pillars using rock mechanics instrumentation to monitor the resulting stress on pillar remnants and stope backs was devised. The paper describes the test work done on the rock types within the pegmatite dyke. The use of Irad stress cells and extensometers in monitoring the stress in pillars is described. The actual results of the program to date are presented.

Jan 1, 1983

By Riki Kobayashi, Donald L. Katz

The dew point of natural gas which has been in equilibrium with gas hydrates has been reported to be lower than that obtained for natural gas in equilibrium with water1,? Hammerschmidt' reports a lowering of the dew point of 13 F for a natural gas in equilibrium with hydrate at 380 F and 525 psi. Records and Seely2 likewise show that the dew point of gas leaving hydrate separators' is as much as 150 F below the separator temperature. This paper presents the reasons for the observed differences between the equilibrium temperatures and the dew point temperatures. Descriptions of the dew point determination by the Bureau of Mines and ASTM tester3 indicate that the dew point is taken as the temperature at which liquid water droplets first begin to appear on the cooled mirror surface even though the temperatures involved are below that required for the formation of gas hydrates or ice. PRESSURE-TEMPERATURE DIAGRAM FOR METHANE-WATEK SYSTEM Fig. 1 presents a schematic pressure-temperature diagram for the methane-water system" for some constant pressure between the critical pressures of pure methane and pure water i.e., pressures frequently encountered in pipeline operations. The possible equilibrium relations are shown by the heavy solid lines. Curve AE represents the saturated water content or dew point of gas in equilibrium with a water-rich liquid solution while curve EF represents the dew point of gas in equilibrium with hydrates. In addition the dotted line DE labelled "metastable dew point" is introduced to explain the apparent discrepancy betwceen the dew point determination and gas-hydrate equilibria. Thermodynamics place certain restrictions on the location of line DE6, namely, that (1) the concentration of water along the line DE be greater than the concentration of water along EF or that the metastable line split the angle formed by the intersection of line GE and EF

Jan 1, 1956

By Stein Wennberg, Snorre Tessem

INTRODUCTION The mine is situated in the middle of Norway 150 km north of the town Trondheim. The iron ore deposits were discovered in 1906 and have been continuously mined since. The first owner was A/S Nordiske Grubekompagni. In 1912 Fosdalens Bergverks-Aktieselskab was established; since World War II it has been a wholly state-owned company. The location is advantageous, with mining facilities, ore dressing plant and stockpile situated near the northern head of the Trondheimsf jord. The iron ore always occurs in Ordovician lavas and sediments, now altered to greenschists, keratophyres and limestone. The ore bearing zone is 150 km long. The deposits consist of two parallel linear ore bodies lying one above the other in the same stratigraphic horizon which dips 70' to the south. The upper body is 50-100 m high, the lower one 250 m high, while the distance between the two bodies in the East mine varies between 20 and 60 m. The ore width varies between 5 and 8 m. The ore bodies strike WSW and plunge between 10' and 15" in this direction. To date continuous ore has either been worked or opened up along a total strike length of 10 km. Until 1969 all ore was mined in the western part of the deposit called the Western mine. In the spring of 1969 production started in a new mine, the Eastern mine. The ore bodies in this new mine are geologically the same as in the old mine, but they have been displaced 700 m downwards along a major fault in the Fosdalen valley.

Jan 1, 1981

By R. P. O’Shea

AS part of a program to investigate phase relationships in ternary systems containing semiconducting elements and compounds, an X-ray survey of alloys in the system Pb-Te-Bi was carried out which revealed that the pair PbTe-Bi probably formed a quasibinary system. This portion of the ternary was examined fully by thermal analysis, X-ray, and microscopic procedures. More than twenty-five alloys were made by melting together the proper combinations of the elements in quartz tubes at a temperature of 1000o C. The compositions which were high in PbTe content were prepared in evacuated, sealed, quartz tubes, allowed to freeze in vacuum, and then transferred to Crucibles for thermal analysis. The bismuth-rich alloys were made directly in the crucibles under a protective gas cover. The starting elements were obtained from the American Smelting and Refining Co. and had a purity greater than 99.99 pct. Cooling curves were made with about 50 g of alloy in graphite crucibles which were placed in a covered quartz container in which a protective atmosphere of helium or nitrogen was maintained. The thermocouple protection tube was made of mul-lite and served as a stirring rod when connected to a reciprocating stirring motor. Temperatures were

Jan 1, 1962