Search Documents

By Robert H. Richards

The group of four papers on ore dreseing read at the Butte meeting, all of them dealing with the recent developments at the Great Falls and Washoe plants of the Anaconda Company, form an extremely important contribution to the subject of ore dressing. It proves the efficacy of the new hindered-settling principles first brought out in a paper entitled Close Sizing Before digging' and later elaborated in a paper entitled Development of Hindered-Settling Apparatus: and it is the first large demonstration on this class of mill that has been made. It must be very gratifying to all mill men to have these papers at hand, charged with careful investigations and results pointing to the conclusions reached; the papers cannot fail to be a great help to every designer of mills and to mill men who are working on this class of concentration. The papers have dealt with their subjects so completely and have demonstrated every point from beginning to end in each case so thoroughly it leaves little for the commentator to say in the way of criticism. Therefore it seems best to him to confine himself to adding a few points of history which he believes will be interesting to the readers. Referring to the paper by Mr. Wiggin, and to the fact that the Richards hindered-settling pulsator classifier was turned down, the writer wishes to say that this classifier was the first of its kind that had ever been introduced, and since that time it has undergone great developments which he believes would overcome the difficulties encountered in the test,. In fact, there was one test made at Great Falls which with the Wilfley tables and vanners brought all the tailings down to 0.36 per cent. copper except the fine slime. Since that time, and since the classifier has been further developed, in one Colorado mill it proved a wonderful amalgam catcher, catching in all

Jan 1, 1914

Key elements of open-pit design fixing the ultimate pit limits are stripping ratio, pit slope angle, and grade cutoff. Results of exploratory and development drilling should be reduced to horizontal sections corresponding to level spacing. It is advisable to interpolate the actual drillhole values to a uniformly spaced 50-ft grid system. Vertical sections can be and are used to approximate the fixing of pit limits, but horizontal sections must be used to optimize a pit design. To develop a pit design requires the establishment of the break-even stripping ratio. This ratio is applied only at the surface of the final pit and must not be confused with the over-all ratio, which is always less; otherwise there would be no profit in the operation. The break-even stripping ratio is determined by the formula: [ ]

Jan 10, 1967

By John P. Ashby

Mine production blasting is a process of destruction of rock masses in order that ore may be extracted. Many open pit operations are faced with the apparently conflicting requirements of providing large quantities of fragmented rock for the processing plant and of minimizing the damage inflicted upon the surrounding pit slopes. A reasonable compromise between these two conflicting demands may often be found by means of simple engineering of production blasts. Many operations tend to rely too heavily upon traditional wall control techniques to alleviate a problem already created by the production blasts. Various production trends including use of larger blastholes and patterns have tended to aggravate the situation. These practices only serve to emphasize the need for engineered improvements. Central to blasting engineering is the process of systematic trial and evaluation. Changes to the blasting system should be made singly, starting with the simplest. This paper discusses simple changes involving drill pattern control, effective use of blastholes and explosives, adequate delaying including use of down-the-hole sequential techniques, effective utilization of free faces, and avoidance of "choked" situations. By directing explosive effort where it is needed, such changes generally result in a significant improvement of slope conditions and of production blasting cost and performance.

Jan 1, 1983

By Horace Tharp Mann

Jan 1, 1926

By Klaus W. John

The geologic factor of greatest significance in rock mechanics and rock engineering is considered to be the geologic structure represented by joints, faults, and other planes of weakness. This geologic structure differentiates between the rock element and the rock system composed of these elements. Only during the last decade has the difference of the technological properties of element and system been recognized but this appears to be more in theory than in engineering practice. If rock mechanics is to achieve real significance in engineering practice, it has to provide methods of analysis which are realistic compromises between the best representation of the actual conditions and pragmatic engineering. The rock mechanics practitioner has to face the fact that many geological engineering and rock mechanics problems may be too complex to allow rigorous analysis but at the same time are deemed satisfactory for the construction of major structures. Ultimately, the geotechnical engineer or the engineering geologist has to express the effect of geologic factors in quantitative, even if approximate, terms and provide numerical data on strength and deformability of rock systems to be utilized in construction. Qualitative evaluations, quantitative descriptions of geologic features as such, and comparisons of specific test results are always of interest but may not suffice as basis for engineering decisions and designs. The present efforts of the rock mechanics group at the Karlsruhe University, Federal Republic of Germany, are based on a systematic combination of geomechanical models and numerical analyses based on the finite element approach. This group considers that at the present stage

Jan 1, 1970

By F. Weinberg

INTEREST is currently being directed toward grain boundary morphologies in zinc in terms of grain boundary facetingl and grain boundary energies.' Some years ago the present author attempted to measure grain boundary energies in 99.999 pct purity Zn as a function of boundary angle, using the standard procedure of measuring equilibrium angles of the boundary traces at triple points. This followed an investigation he carried out on preferential melting of |H (112) Fig. 1—Electron transmission micrograph of a stacking fault, grain boundary intersection in copper. GRAIN BOUNDARY STACKING FAULT Fig. 2—Schematic representation of the intersection of Fig. 1, indicating inclination angles 0 and trace angles $. specimens were prepared by the Bollman technique in an electrolyte of 70 pct methanol, 30 pct HNO3 main-tained at -30°C. The interfacial free energy of the high angle grain boundary and of the stacking fault is assumed to be thermodynamically equivalent to the corresponding in-terfacial tensions. In terms of the true dihedral angles & between the intersecting interfaces, the equilibrium of interfacial tensions in the direction parallel to the stacking fault yields: ysF = -ygb(cos F1+ cos ±cosF2) Here, ysF is the stacking fault free energy and ygb is the grain boundary free energy, assumed equal on both sides of the intersection. Forces acting normal to the grain boundary, of the form ??gb/?F,l are assumed negligible as the grain boundary remains straight for a considerable distance on either side of the intersection. The micrograph of Fig. 1 may actually consist of several closely spaced stacking faults on the same slip plane. The actual point of intersection between the grain boundary and the first stacking fault, and the equilibrium configuration of the intersection, should not be affected by the presence of the other faults, as

Jan 1, 1970

By A. T. Miesch

The purpose of this paper is to explore relations between the distribution and composition of uranium deposits on the Colorado Plateau and mineralogic, chemical, and lithologic aspects of their host rocks. The paper also appraises the host-rock sandstones as possible sources of elements in the uranium deposits. Other possible sources of elements are not discussed. Uranium deposits on the Colorado Plateau consist largely of sandstone and small amounts of mud-stone impregnated with uranium and vanadium miner- als and a suite of minor accessory minerals containing copper, lead, zinc, silver, iron, cobalt, nickel, yttrium, molybdenum, selenium, and arsenic, in addition to other elements locally. The deposits consist of clusters of closely spaced ore bodies which commonly aggregate several thousand tons, but range in size from less than one ton to several million tons. With only rare exception, the deposits show no close relation to fractures. The ore bodies are generally tabular in layers nearly parallel to the bedding in the host rocks, or they cross bedding at large angles to form roll structures. Absence of fracture control necessitates that the ore and associated elements were transported to the deposits by way of interstitial pore spaces in the sandstones. This points to the general process of lateral secretion as a possible mechanism of ore formation, and suggests the host-rock sandstones as a possible source of the metals. Roll structures in the ore

Jan 1, 1962

[ ]

Jan 1, 1938

By A. C. Dorenfeld

Ores of the Mammoth mining district, some 45 miles northeast of Tucson, Arizona, are treated by Mammoth-St. Anthony, Ltd. The ores now treated come from a complex system of veins and faults, comprising three mines, in close proximity: The Mohawk, Mammoth and Collins. The ore treated in the past was oxide ore, which contains economic amounts of gold, silver, lead, molybdenum, and vanadium (as wulfenite and vanadanite). The lead-zinc sulphide ore has never been treated before. The Ore The sulphide ore contains galena, sphalerite, marmatite, pyrite and some chal-copyrite, covellite, chalcocite and bornite, as well as small amounts of gold and silver. The value of the ore is principally in the lead and zinc content. The lead-zinc sulphides are substantially liberated at a minus 65-mesh grind. However, a large part of the chalcopyrite and other copper minerals is not freed, but remains as pin points on the sphalerite. Economically, the copper is unimportant. The gangue is a rhyolite granite, with very little limestone. There is no molybdenum or vanadikm in the sulphide ore. History of Sulphide Treatment Test work on samples of the sulphide ore was conducted by several equipment companies, the Arizona Bureau of Mines and the company's laboratory. Results of this test work indicated that for some reason, which at the time could not be explained, recoveries would be only about 65 per cent lead and 50 per cent zinc. Notwithstanding this, because of the nation's need for metals, the management built a 150-ton treatment plant. The mill was started in June 1942. During December 1942, using the standard method of treating lead-zinc ore, the monthly results were as shown in Table I. These results were poor. Too much lead was in the zinc concentrate, and too much zinc in the lead concentrate. It should be noted here. that prior to December attempts were made to depress the sphalerite with large and varied amounts of cyanide, zinc sulphate, and sodium sulphite with poor results.

Jan 1, 1947

By W. G. Pfann

WHEN a molten zone traverses a long, solid ingot in a level, open boat the ingot becomes tapered. While the taper may be slight after one zone pass, it can be appreciable after repeated zone passes, even to the extent of causing an overflow of matter at the end of the boat. It will be shown here that such matter transport by a molten zone arises from the volume change on melting and that it corresponds in magnitude and direction to the magnitude and sign of the volume change. It will be shown also that the mechanism of matter transport is basically similar to that of solute transport by a molten zone, which has been discussed elsewhere,1,2 and that the two processes can be described by similar equations. Finally it will be shown that matter transport can be prevented by inclining the ingot at a critical angle. Contraction on melting results in forward transport, that is, transport in the direction of zone travel; expansion on melting results in reverse transport. The way in which forward transport arises from the contraction on melting may be seen as follows: At the starting end of a solid horizontal ingot of uniform rectangular cross section of height h., form a molten zone of length 1, as shown in Fig. 1. The height h of the liquid will be h. where a is the ratio of density of solid to that of liquid. Advance the molten zone, at constant length, a distance dx. The volume of solid melted will be hdx; the volume of solid frozen will be Izdx, because the height of the freezing solid will tend to be equal to that of the liquid. The resultant change, dv, in liquid volume will be the difference in these quantities multiplied by the density ratio. Hence the following equation may be used for a zone at any distance x from the origin: which is valid in all but the last zone length in the

Jan 1, 1954

By M. R. Louthan, C. L. Angerman

In polycrystalline Zircaloy-2 the orientation of zirconium hydride precipitates is influenced by an applied stress during hydride precipitation; hydride platelets are oriented nearly parallel to a compres-sive stress and perpendicular to a tensile tress. 1,2 A similar effect has been observed in the Ti-H system, where precipitation of the low-density hydride platelets occurred on habit planes made energetically favorable by the application of stress. 3 Recently, stress activation of hydride habit planes in zirconium and Zircaloy-4 was also demonstrated. The hydrides precipitated on {101l), {112l} and (2131) planes in both zirconium and Zircaloy-4; however, no platelets were found near the prism-plane positions in the Zircaloy-4 samples. Investigations at the Savannah River Laboratory, using polycrystalline Zirc_aloy-2 samples, have confirmed the (101l) and (1121) habit planes but also showed that the prism planes were active hydride habit planes. Using single-surface stereographic analysis and back-reflection Laue techniques, most of the previously reported habit planes for a zirconium were observed.4"1 and one additional plane, the (1013) plane, was noted, Table I. All the habit planes observed had the form (101l) or { 112l) indicating that these planes are the habit planes for hydride precipitation in poly-crystalline Zircaloy-2. The specimens used in these studies were cut from large-grained weld areas of seam-welded tubing and were hydrided in either a static steam autoclave at 400°C and 1500 psig or in a modified Sieverts apparatus at 400°C.

Jan 1, 1967

By H. I. Smith

The technical and safety press have devoted much space in support of or in opposition to the use of booster and auxiliary fans in coal mines. The Mine Safety Board of the U. S. Bureau of Mines has given the matter consideration, and the Mine Ventilation Committee of the A. I. M. E. is now seeking a discussion of the merits and demerits of such fans to guide it in formulating recommendations. In this paper I will set up some principles on which I believe most engineers will agree and from which we may work toward a decision, though as to what that decision shall be there may be a difference in opinion. Before stating the points on which I believe there is accord, I will distinguish between booster and auxiliary fans. Definition of Booster and Auxiliary Fans In discussing underground fans G. S. Rice1 distinguishes between those used to increase the amount of air passing a given point and those used to augment the ventilation locally. He describes a booster fan as one which is installed to handle the entire air current passing a given

Jan 1, 1927

By G. W. H. Norman, A. H. Miller

This survey is one of the more recent tests of geophysical methods of prospecting by the Dominion Observatory and the Geological Survey of Canada, of which the purpose is to find out what application such methods may have to geological problems in Canada. The Malagash salt deposit lies on the north shore of Nova Scotia about 40 miles east of the New Brunswick boundary, arid forms a part of faulted and folded Carboniferous strata. The salt beds are exposed only in the mine workings, which are about 1000 ft. deep and at one place extend for 1000 ft. along the strike. Lack of rock exposures, complicated folds, and faults make it impossible to predict the location of salt away from the mine. A survey of an area in the vicinity of the mine was therefore undertaken to find out whether the salt could be located by the torsion balance and whether its extension from the mine workings could be traced. As the gravitational effects at Malagash may be fairly typical of those at other concealed salt deposits in the Carboniferous rocks of the Maritime Provinces of Canada, the survey has a direct bearing on prospecting for other deposits. The survey was made in 1934 by A. H. Miller in collaboration with Dr. W. A. Bell, of the Geological Survey of Canada. Observations began on June 15 and were completed four months later, on Oct. 15. Definite gravitational effects including a lowering of gravity were observed over the deposit. The survey also disclosed one other area of low gravity cast of the mine hut whether this area is underlain by a large body of salt is not yet established.

Jan 1, 1938

By Y. C. Liu

IN the study of the rolling recrystallization of face-centered-cubic metals, a most unusual observation is the frequent occurrence of a sharp re-crystallization texture of cube orientation. Although the general conditions under which this texture occurs are known,2,3 its origin is still not well understood. Based on the observed relationship between the {110}<112> deformation texture and the (113}<211> recrystallization texture, regardless of the effect of alloying elements2,4,5 or the symmetry of the deformation texture,&apos; there is a strong indication that a specific component of the deformation texture is related to a specific component of the recrystallization texture. Using the rotational reorien-tation relationship as a means of correlating the deformation and recrystallization textures, it was proposed that the deformation component which related the cube texture has {358)<523> indices."&apos; The investigation reported here was undertaken to seek experimental evidence for the validity of this proposition. Experimental Procedure Two copper single crystals having an initial orientation within 2" of (358) [523] indices were prepared in the manner described in Ref. 5. The purity of the copper was between 99.94 and 99.97 pct. The original dimensions of the crystals were as follows: specimen A, 0.465 in. thickness, 0.844 in. width, and 0.955 in. length; specimen B, 0.535 in. thickness, 1.120 in. width, and 1.36 in. length: Rolling was done on a laboratory rolling mill according to the following schedule: 0.010 in. per pass to 50 pct reduction in thickness, 0.005 in. per pass to 70 pct reduction inthickness, 0.002 in. per pass to 85 pct reduction in

Jan 1, 1958

By W. J. Taylor

FURNACE-MEN who have not taken advantage of the use of dynamite in certain blast-furnace troubles, as explained by Mr. Witherbee in his valuable papers read before the Institute some years since, cannot appreciate the quick relief and great advantage that may be derived at times from its judicious employment. Before giving my experience in the use of high explosives in blastfurnace troubles of certain kinds, I will record a method I have used with marked success in " blowing down." Had I not understood, however, the use of powder, I would have " salamandered " effectually the first time I tried it. Early in my straight-furnace experiments, last summer, at the Chester, N. J., Furnace, I wanted to blow down to within 3 or 4 feet of the tuyeres. To do this with a down-comer not lined, and without putting in any limestone to keep the gases cool enough to do no harm, was not an easy task. We could keep the bell and hopper cool by filling them with water, say 12 inches deep; but before we got the stock down 15 or 20 feet the pyrometer in the gas-flue on top mas up to 1300°, and the clowncomer was red-hot, with the heat still rising. In this emergency my assistant, Mr. N. M. Langdon, urged the trial of a plan lie had often advocated, viz., the introduction of water in some way under the bell in the proper quantity, in order that its evaporation might absorb and reduce the heat of the escaping gases to a point where it would not do any harm. He thought the bell

Jan 1, 1885

By P. W. George

The rapid increase in cost of discovering new orebodies by churn drilling in the Tri-State district has led to some attempts to lessen the expense by using geophysical methods. Electrical prospecting was tried three or four years ago, but no successful results were recorded. In 1926, the Federal Mining and Smelting Co. engaged the North American Exploration Co., of Houston, Texas, to make some tests with the torsion balance. At first, it was thought that the most favorable conditions for discovery of ore deposits with the torsion balance would be in locations where the ore was known to occur at rather shallow depths, therefore the first trial was made at Ducnweg, east of Joplin, where some zinc ore had been developed at a depth of 130 ft. The gravity gradients at 61 stations on a tract of about seventeen acres indicated plainly one large zone of maximum gravity and a smaller narrow zone of minimum gravity. Fourteen churn-drill holes, half of which struck ore, show that all the ore found was located outside the zones of maximum and minimum gravity. In the zone of maximum gravity the limestone beds were closest to the surface, and the first chert beds encountered were at the greatest depth. The results (shown in Table 1) indicated that the gravity of the limestone was greater than the gravity of the fractured chert together with its orebodies, and probably also greater than the bouldery soil and clay on top of the limestone. A cross-section of the Duenweg lease is shown in Fig. 1.

Jan 1, 1929

By R. Jr. Schuhmann

PROBLEMS in expressing, interpreting, and using size-distribution data recur in many phases of mineral dressing; therefore it is desirable that size analyses be ex-pressed in such a form, either numerically or graphically, that comparisons can be made readily. The size distribution of comminuted material is a result of a specific physical operation on the material and therefore should be governed by some definite physical principle, or cause-effect relation. Although this principle has not been dis-covered, it has been found that the size distribution of comminuted, homogeneous solids may be expressed by relatively simple mathematical equations. Two equa-tions in particular, proposed by Gaudin1 and by Rosin and Rammler,2 respectively, have stood out, both having wide demon-strated ranges of application. The form and the method of application of the two appear almost irreconcilably different on the surface, but, as will be shown, they are asymptotic in the fine sizes when expressed in the same units. This paper gives the results of a further study of the Gaudin and Rosin-Rammler relations, made with the object of develop-ing a form of size-distribution equation that will be more usable and more signifi-cant-particularly in comminution studies, both for interpreting the nature of size distribution and for evaluating surface. The work is summarized in the following:

Jan 1, 1940

By Robert J. Linney

Reserve Mining Co. produces 5 million tons of iron ore pellets per year. The finished product runs about 65.50 pct Fe, with 7.75 to 8.00 pct SiO2. Less than 12 pct arrives at the blast furnaces smaller than 3/8 in. This plant was originally designed to produce 3.75 tons annually-not 5 million. To handle the increased tonnage a fifth fine crushing line was added, and some very minor changes were made.

Jan 9, 1959

By Giovanni Barla

In engineering analyses, rock is frequently treated as a homogeneous, isotropic, and linearly elastic medium. However, rock material exhibits, in most cases, physical nonlinearity, time-dependency, and anisotropy. In some instances, anelasticity due to nonmechanical effects, such as density and temperature changes, must also be taken into account. The influence of these different anomalies in the physical behavior of a rock material is often neglected. An estimate of the discrepancies which are introduced when classical theory of elasticity is used is consequently required. The easiest theoretical path by which these discrepancies can be analyzed is to vary the constitutive equations of the rock material. The constitutive equations, representing various physical experiences with different types of media, define a class of ideal substances. Assuming different constitutive equations for the description of the rock physical behavior, one can establish a sensitivity analysis to determine how much information is contained in elastic theory for reliable design purposes. The method may be applied also using numerical techniques (e.g., finite element or finite differences) which, because of the nature of the formulation, require one to assume in each case the rock constitutive equations. Theoretical and experimental work is needed to be able to perform such analyses with confidence. Adequate and practical procedures for the determination of the material functions which enter the various constitutive equations must be established. This paper presents such an attempt with respect to the simulation of some behavior patterns of rock material. It is felt worthwhile to stimulate activity in this field and it is hoped to contribute to this objective.

Jan 1, 1970

By Walter W. Bradley

Barite, or barytes as it is sometimes called, belongs to one of the lesser groups of nonmetallic minerals, of which 15 to 20 varieties are mined in California in amounts varying in value from a few hundred to almost half a million dollars annually. Commercial production of barite in California, according to the records of the State Mining Bureau (now Division of Mines), began in the year 1910 with shipments totaling 860 tons, valued at $5640 f.0.b. rail shipping point. With the exception of the years 1924 and 1925, when no shipments were made, the output has varied, reaching a maximum of 17,993 tons, worth $90,617, in 1927. The 1928 output was 13,406 tons, worth $55,888 f.0.b. rail shipping point, bringing the state total to the end of 1928 to 59,972 tons, valued at $313,930. Consumption of BaRitE in United States Crude barite sold or used by producers in the United States for the year 1927 amounted to 248,219 tons, valued at $1,594,423, according to the U. S. Bureau of Mines.l In addition, there was imported, principally from Germany, a total of 70,274 tons, valued at $253,284. Manufactured products from these tonnages combined were distributed in 1927 (the latest year for which figures are at present available) as follows: ground barite, 57,658 tons; lithopone, 174,083 tons; barium chemicals (including carbonate, 4,960 tons; chloride, 3,541 tons; binoxide and sulfate or blanc Jixe combined, 13,354 tons). Missouri accounts for nearly 50 per cent of the domestic crude barite, followed by Georgia and Tennessee, with lesser amounts from Arizona, California, Nevada, South Carolina, and Virginia. Occurrence and Uses of Babite2 Barite, also called "heavy spar" and "tiff," is theoretically composed of 65.7 per cent of barium oxide (BaO) and 34.3 per cent of sulfur

Jan 1, 1931