Search Documents

By F. E. Lathe, L. Hodnett

This paper summarizes extensive data supplied by 40 copper converter plants in 18 countries, and includes a partial analysis and comments on the effect of converter slag composition and temperature on the fomzation and elimination of magnetite and the life of basic and neutral refractories. APRELIMINARY draft of this paper, including data from 26 companies which had submitted replies to a questionnaire, was presented at the Annual Meeting of the AIME held in New York in February, 1956. Publication was delayed in the expectation that additional replies would be received, and justification for the subsequent delay may be found in the fact that the present revised paper contains data from 40 converter plants situated in 18 different countries. The suggestion that a questionnaire be sent to the major copper and copper-nickel plants outside the U.S.S.R. and associated countries arose at the Los Angeles Annual Meeting in February, 1953, where several papers dealing with converter construction and operation were presented. In private discussions which followed, a group of metallurgists and refractories engineers raised the question why practices varied so much at different plants. Why did magnesite brick give superior service to chrome-magnesite in some plants but chrome-magnesite prove superior in others? Would metallurgical studies point the way to the development of still better refractories? Could magnetite formation be prevented in converter slags and reverber-atory furnace mattes? If this was feasible, why was a heavy circulating load of magnetite tolerated, when, in all probability, it increased copper losses in the reverberatory slags and, in some cases, made it necessary to shut down the furnaces periodically to clean out the accumulated magnetite? Was the sole purpose of coating brick with magnetite that of

Jan 1, 1959

By O. P. Arora, M. Metzger

Single-phase aluminum containing 1 to 600ppm copper was studied in 7 to 26 pct HCl. The corrosion rate in the autocatalytic stage was resolved into a constant intrinsic component and an acdelerating autocatalytic component, and attention was focused on the part of this stage where the corrosion rate could be described by a simple empirical relation. Autocatalytic corrosion in this period was localized and its rate increased rapidly with copper content and with the strength and chlaride content of the acid. The effects of adding cupric ion to 16 pct HCI were functionally and quantitatively inconsistent with the autocatalytic rates observed. A theory of these rates was given based on the deposition in nzetallic contact with the aluminum of part of the copper introduced by corrosion. It has long been known in a general way that aluminum containing sufficient copper suffers in hydrochloric acid an autocatalytic acceleration of corrosion resulting from the introduction into the acid of copper ions and their reduction on the specimen as elemental copper, which provides cathodes of low hydrogen overvoltage.'-3 In a previous paper, this phenomenon was identified in single-phase high-purity material at copper levels as low as 20 ppm and an empirical equation describing autocatalytic corrosion rates in 16 and 20 pct HC1 was presented. In the present work the range of acid strength and chemistry studied was extended, a more accurate empirical equation for the autocatalytic rate was determined, and a theory of this rate was formulated. A major source of interest in this system is the intergranular corrosion, which is also strongly influenced by copper content,= and an objective of the present work on general corrosion was to provide a basis for studying the role of copper content in intergranular corrosion, which is experimentally much less accessible.

Jan 1, 1963

By Alden B. Greninger, Victor G. Mooradian

Microscopic examinations of quenched (beta) 60:40 copper-zinc and quenched (beta) 74:26 copper-tin alloys have frequently disclosed long, thin parallel bands or markings within the polyhedral beta grains. Apparently, it has been accepted that these markings are mechanical twin bands, although there is no published account of experimental data that might tend to substantiate this belief for the copper-zinc system, and only meager evidence has been submitted for the copper-tin system. Johnsonl0 commented upon the markings he observed after deforming a quenched brass of 55.6 per cent copper and 44.4 per cent zinc. Clark's papers4 on the heat-treatment of Muntz metal contain many photomicrographs of markings in beta brass; these she referred to as Neumann bands (inasmuch as repolishing and re-etching failed to remove them) and stated that markings present in Muntz metal as quenched were the result of shock imparted during the polishing operation. Van Wert18 first suggested that these parallel markings in quenched beta brass (60:40) might be alpha precipitated along certain crystallographic planes of the matrix lattice. He showed that upon reheating the specimens to temperatures below 800" C., obvious precipitation of alpha within the large beta grains first occurred at the markings. In a discussion of this paper, Phillips stated (pp. 505-507) that in his opinion the markings observed by Van Wert were mechanical twins resulting from contraction strains produced during the quenching operation. In a study of segregate structures in beta copper-tin, Smith17 observed that in the quenched beta phase (containing 74.92 per cent Cu) parallel . bands or markings very similar to those in metastable beta brass could be

Jan 1, 1938

By Alden B. Greninger, Victor G. Mooradian

Microscopic examinations of quenched (beta) 60:40 copper-zinc and quenched (beta) 74:26 copper-tin alloys have frequently disclosed long, thin parallel bands or markings within the polyhedral beta grains. Apparently, it has been accepted that these markings are mechanical twin bands, although there is no published account of experimental data that might tend to substantiate this belief for the copper-zinc system, and only meager evidence has been submitted for the copper-tin system. Johnsonl0 commented upon the markings he observed after deforming a quenched brass of 55.6 per cent copper and 44.4 per cent zinc. Clark's papers4 on the heat-treatment of Muntz metal contain many photomicrographs of markings in beta brass; these she referred to as Neumann bands (inasmuch as repolishing and re-etching failed to remove them) and stated that markings present in Muntz metal as quenched were the result of shock imparted during the polishing operation. Van Wert18 first suggested that these parallel markings in quenched beta brass (60:40) might be alpha precipitated along certain crystallographic planes of the matrix lattice. He showed that upon reheating the specimens to temperatures below 800" C., obvious precipitation of alpha within the large beta grains first occurred at the markings. In a discussion of this paper, Phillips stated (pp. 505-507) that in his opinion the markings observed by Van Wert were mechanical twins resulting from contraction strains produced during the quenching operation. In a study of segregate structures in beta copper-tin, Smith17 observed that in the quenched beta phase (containing 74.92 per cent Cu) parallel . bands or markings very similar to those in metastable beta brass could be

Jan 1, 1938

By AIME AIME

CONVENTION plans for the A.I.M.E. Regional Meeting to be held on the Minnesota Iron Range Aug. 12 to 1.5 are being completed to give the visiting member?s from all parts of the country a wide variety of technical and recreational features. High spots of the social events are the official dinner, dance, luncheon and golf: and of course, special provision is being, made for the entertainment of visiting ladies. The technical sessions will fit in with scheduled trips to view all phases of mining, beneficiation and transportation of iron ore. Men from the West and Southwest will find much of interest in the detail of the mining operations. A trip to the steel plant of the

Jan 1, 1941

By H. H. Richardson, E. H. Dix

Of all the alloying elements used in commercial aluminum alloys, copper stands out as by far the most important, and it is perhaps for this reason that the constitution of the aluminum-copper system has received the attention of a number of experimenters covering a period of approximately 20 years. It would be expected that during this time the equilibrium relations would have been thoroughly and exactly worked out. In a general way this is true, but there is a surprising lack of agreement in the details of the high aluminum end of the diagram, particularly in regard to the solid solubility of copper in aluminum, which has been given variously as 2 per cent. to 5 per cent. at the eutectic temperature. The importance of this is much greater than might at first appear to one unfamiliar with modern commercial aluminum alloys. This is true because, with one exception, the susceptibility of the strong alloys to heat treatment depends, in part at least, upon the solid solubility relations of copper in aluminum. In 1919, Merica, Waltenberg, and Freeman1 published the first detailed information on these solubility relations. They found that the solubility of copper decreases with falling temperature from about 4 per cent. at 525" C. to about 1 per cent. at 300" C. and is apparently still diminishing at lower temperatures. In 1921 there was published a brief account of the results obtained in the National Physical Laboratory, Teddington, England.2 This laboratory, however, reported that 5 per cent. of copper is soluble in aluminum at 540" C., and that this amount decreases to about 3 per cent. at 20" C. In the same year Ohtani and Hemmi3 reported a solubility of 4.8 per cent. copper at 520" C., 2.6 per cent. at 460" C. and 1.5 per cent. at 420" C.

Jan 1, 1926

By AIME AIME

IN A STATEMENT summarizing general conditions in the Federated American Engineering Societies, the executive secretary, L. W. Wallace, expresses the belief that the Federation has made substantial progress. At the annual meeting of the American Engineering Council, to be held in Washington Jan. 5 and 6, this progress will be shown by reports covering activities in many fields. "Unquestionably," says Mr. Wallace, "the Federa¬tion has made favorable and permanent contacts in Washington. Through the, activities of Congress and of the new Federal administration. we have had the opportunity to render some really constructive service. We feel, however, that the great body of engineers are not adequately informed of the organization of the Federation, of its aims and purposes and of its activities.

Jan 1, 1921

By AIME AIME

THE best meeting ever held, was the opinion expressed by a number of those who attended the annual meeting of the Institute in New York, Feb. 18 to 21, and there was an atmosphere of friendliness and good fellowship about it that fully justified the feeling. In numbers it was not quite so large as last year and unless the Engineering Societies should build for themselves a new building it is probable that no meeting can be larger, in respect to numbers, than that held in 1928, which was only made possible by the circumstance that the eighth floor of the building happened to be, temporarily vacant at the time. The number of rooms available for -sessions that were provided when the building was built long ago proved inadequate, and it is only by the expedient of obtaining the temporary use of the board and committee rooms of other societies that it is possible to arrange for the over 40 sessions that must be spread over the four days of the meeting. The-fifth floor, where. a buffet lunch is served each-day, has reached its full capacity and it seems quite evident that any future development of Institute meetings must be along the lines of quality, not size.

Jan 1, 1929

By J. E. Tobey

THERE are a lot of good things about this great industry of ours. Let us stop commiserating and consider some of the things that are right in this business. Coal is number one in the basic material industries. Our civilization owes more to it than to any other basic commodity. We are literally immersed in the benefactions of coal. In cur man-made world it is indispensable and we are constantly surrounded by objects, materials, and services which owe their existence to coal. Practically all the important materials, such as iron, steel, brick, cement, lime, rubber, glass, cotton, and wood have felt its magic touch.

Jan 1, 1939

By J. Moore Samuel

THE prospective change in ore receipts at the Copper Queen reduction works necessitated a careful study of conditions to determine the most economical method of smelting. The first step, calculating the known, probable, and possible results, showed the economy of a unimetallurgical flow sheet f which the three pyrometallurgical stages would be roasting, reverberatory smelting, and converting. The past and future ore receipts (not including converter flux) are as follows: AVERAGE MONTHLY FUTURE MONTHLY RECEIPTS, 1918 RECEIPTS TONS PER PER CENT. OF TONS PER PER CENT. OF MONTH TOTAL RECEIPTS MONTH TOTAL RECEIPTS Ore 84,553 82.3 43,000 44.0 Gravity concentrates 16,375 15.9 25,500 26.0 Flotation concentrates 1,883 1.8 29,400 30.0 Total 102,811 100.0 97,900 100.0 Of the 102,811 tons per month received in 1918, only 28,945, or 28 per cent., was treated in the roasters and an average f 14.1 roasters out of 20 were in operation; the remaining ore was treated in the blast furnaces. The change to "all reverb." practice, therefore, called for considerable additional roaster capacity, which could be obtained either by building additional units, or by remodelling the present units so as to give increased unit capacity. In view of the progress in roasting practice since the construction of the Copper Queen roaster plant and the heavy investment in that roaster plant, the second plan seemed to be the more desirable. The Copper Queen roaster plant consisted of twenty six-hearth, McDougall roasters, 18 ft. in diameter, equipped with cast-iron arms that originally were water cooled but now are air cooled. They have no top dry hearth and the feed is discharged through the top arch, near its periphery, by plunger feeders from two bins at opposite sides of the roaster.

Jan 7, 1921

By Sheldon P. Wimpfen, Ralph H. Sweefser

FOR centuries the pumping of water has been one of the chief problems to be overcome by the persistent men who win the mineral wealth of the world. Profitable operations have often been forced to suspend activities as the mine penetrated well below the water table or when sudden rushes of water were encountered. To operate below the local water level requires continuous pumping equal in volume to the amount of water flow¬ing into the mine workings. Often the water to be removed exceeds the tonnage of valuable material produced. To be above local water level is a valuable asset. Modern mining practice permits nothing short of the extraction of the last pound of profitable ore from a mineral deposit. In the days before the development of mechanical and electrical power as we know it today. water in any quantity was a major

Jan 1, 1948

By C. WIFLARD HAYES

(New Haven Meeting, February, 1909.) I DESIRE to make it perfectly clear at the outset that I fully realize the hazardous nature of any attempt to estimate the quantity of iron-ore or any other mineral in the ground. I should not have had the temerity to venture upon an inventory of the iron-ore supplies of the United States except for the requirements of the Conservation Commission. During the preparation of this inventory I have been impressed by the wide diversity in estimates of those best qualified to. hold an opinion, and I am therefore prepared in advance for criticism of my figures. Inasmuch as this report was prepared in large part for unprofessional readers, I considered it necessary to classify and describe the commercial iron-ores in a somewhat elementary manner, in order to explain the reasons for the large element of uncertainty in the estimates. I have therefore given a chemical and a geological classification of iron-ores, which place the commercial deposits in six classes: (1) magmatic segregations in basic igneous rocks; (2) contact-deposits formed in connection with igneous intrusions; (3) concentration-deposits; (4) replacement-deposits; (5) bedded-deposits, and (6) gossan-deposits. The iron-ores are further distinguished under two classes available and not available. This classification is in large measure arbitrary, and it, is evident that it will vary front time to time. In the available class are placed those ores which can be worked at a profit under conditions essentially as they exist at present. Since it depends wholly on the question of costs, the various factors which affect cost will determine the classification of any particular deposit. Actual production, * Abstract of Report prepared for the Conservation Commission. t Chief Geologist, United States Geological Survey. .

Apr 1, 1909

By Joseph E. Pogue

FOR a number of years the petroleum department of The Chase National Bank has been making a continuing study of the financial aspects of thirty oil companies. (See Pogue and Coqueron, "Financial Analysis of Thirty Oil Companies," pamphlet, The Chase National Bank, November 1945, for data covering eleven years, 1934-1944, and the list of the companies making up the group. See also "Capital Employed in the Petroleum Industry," by the same authors, M&M, November 1944.1 This group represents a large sample of theAmerican petroleum industry, covering about two thirds of the business. Certain aspects of this study concern the capital employed in crude oil production, the main features of which arc presented in this paper.

Jan 1, 1946

By E. H. Erwin Gartner

The Rhenish lignite deposit in the Nordrhein-Westphalia province of the German Federal Republic covers an area on the left bank of the Rhine River of about 970 sq miles (Fig. 1). Here, in the Miocene era, some 20 million years ago a lignite seam was formed and later broken, through tectonic movements into several blocks, some thrown down into depths of over 1,500 ft. This deposit consists of a single seam, in places up to 300 ft thick, but averaging about 150 ft. In a few areas, it is split into as many as five seams, separated by barren strata. It contains about 60 billion tons (2000 lb/short ton) of lignite which, however, being relatively young geologically, has, because of approximately 60% moisture, 2 to 8% ash, and low sulfur, a net calorific value of 3,340 Btu. That calorific value increases, however, with rising thickness of the cap rock. About one-third of the yearly production of 90 to 100 million tons of raw lignites is converted into briquets. Raw lignite is pulverized and dried to about 18% water content and then pressed without binder into briquets under a pressure of about 14,000 psi. The briquets are being used primarily for residential heating; their sales, however, have been declining sharply since 1963. On the other hand, the volume of raw lignite used in steam power plants has been rising steadily and amounts at present (1968) to about two-thirds of the total production. Huge steam power plants, such as Frimmersdorf, shown in Fig. 2 (which, with an installed capacity of 2,600 MW [megawatt], represents the world's largest steam power plant) with a generating capacity of up to 300 MW per unit and a total installed capacity of over 6,000 MW, contribute about 26% of the total electric power production of the German Federal Republic.

Jan 1, 1969

By Robert J. Linney

In the latter part of the year 1943, it was decided to experiment with diamond-drill blast holes in the Old Bed magnetite mine at the Mineville mines of the Republic Steel Corporation, in sections of the ore body where vertical dimensions were large and where development for sublevel bench stopes had already been done. Other possibilities of application for this drilling method were in the reclamation of old floors and pillars in the pitching folds of the Lower Old Bed ore body and in the reclamation of large vertical pillars in the "21" Bonanza-Joker ore body. The cross sections and views of the two ore bodies will show the conditions to which the diamond-drill method has been applied. The Lower Old Bed magnetite ore body is lenticular and dips approximately 30° toward the southwest and strikes generally southeast and northwest. An intensely folded structure, which pitches generally on an axis approximately at right angles to the strike, is continuous from the uppermost old workings down to the present bottom of the mine, and probably continues with depth. On successively lower levels this folded structure becomes greater in vertical dimensions and the two folds are closer together in a horizontal dimension. As shown in Fig. I, this folded structure gives to parts of the ore body considerable vertical dimensions, which provide areas that were developed for sublevel bench stoping above a slushing drift, as shown in Fig. 2. It was in one of these previously devel-oped sublevel bench stopes, No. 26 on the 1185-ft. level, that the diamond-drill blast-hole method was applied for mining the upper sublevel. The lower sublevel was underhand-bench-drilled to the finger raises of the scram drift below. The roof of this stoping area began to break and spall on the lower sublevel, causing the roof to become inclined. Along the hanging wall of the stope this reached an elevation about half way between the two sublevels. A smooth schistose seam in the hanging wall causes the ore to break away freely. Therefore, if bench mining had been carried on in the upper sublevel, a dangerous condition of poorly supported benches would have resulted. When the drillers were slashing across the sublevel te footwall and hanging wall to make a bench, spdlling roof of the opening below would probably have carried away part of the bench, and would have left a dangerous place in which to continue underhand benching. A 6 by 8-ft. raise had been driven between the lower stope and the upper sublevel about 200 ft. from a manway. It was decided to use this raise for a starting cut and to arrange holes as shown in Fig 3, so that a slot would be opened across the ore body between the footwall and hanging wall. This slot would then be used for the purpose of breaking into the ore, by blasting vertical rings of holes drilled at right angles to the axis of the pitching folds as nearly as possible. Layouts of this slot drilling and the rings adjacent are

Jan 1, 1946

MEETING OF SAN FRANCISCO SECTION Twenty members were present at the meeting of the San Francisco Section, May 20, 1919. Chairman Bradley being in Alaska, vice-chairman, T. A. Rickard, presided. Prof. Frank H. Probert gave a short account of the activities of the governmental commission, consisting of himself, George S. Rice, and F. G. Cottrell, which recently visited Europe, and studied the coal, iron, salt, and chemical industries. When the work is finished reports will he issued. He gave a resume of the history of. the changes in nationality of Alsace-Lorraine and 'described the importance of the region for coal, iron, and potash. With the return of these provinces France will have an annual output of more iron ore than she has coke to smelt it with; hence, the importance of the Saar coal field. With these new mines France will take the predominant position in the iron and steel-industry formerly held by Germany. Many details were given of the devastated mines of France, and of their former value, production and the destruction that overtook them. Noteworthy is it that much of the damage was done as late as Oct. 28, 1918, for the express purpose of ruining the country industrially. The damaged area of the Valenciennes coal basin embraced twenty-four concessions, three were damaged by artillery bombardment, but have resumed operations since the' armistice, nine had their surface: equipment destroyed by battle, pillage, and sabotage, while twelve concessions at the eastern-end of-the field suffered from wilful, systematic destruction. Of the 285 shafts in the district, 172 were flooded either by: turning surface streams into them, or, by wrecking the cuvellage; thus, admitting water and quicksand from the water-bearing strata above the coal measures. Two hundred and thirty-five surface plants were damaged, many of them to such an extent that they must be scrapped. These properties gave employment to 135,000 men before the war and, even admitting the remote possibility of getting workmen, the terrible destruction and devastation makes housing and living a difficult problem. It will probably be from 3 to 5 years before the mines are drained and information obtained as to underground conditions; to attain the pre-war output may require from 12 to 15 years.

Jan 8, 1919

"World Mining and Metals Technology" is the title of this year's SME-AIME Fall Meeting and Exhibit in Denver, Sept. 1-3, where a record number of exhibits are scheduled for display. The international theme is particularly appropriate, for in addition to the annual SME session, the Third MMIJ-AIME Joint Meeting will be held.

Jan 8, 1976

By Wheeler North

THE United Eastern Mining Co.'s property is located in the Oatman, Gold Roads mining district of Mohave County, Ariz. The mine and mill are some 26 mi. (41.8 km.) southwest of Kingman, the nearest railway connection. The ore consists of a mixture of calcite and quartz with some andesite. The values, which are mainly gold, alloyed with approximately 34 per cent., by weight, of silver, are extremely fine so that fine grinding is a most important factor in extraction. The milling process, briefly, consists of single-stage, coarse-crushing, two-stage ball milling in cyanide solution, followed by combined mechanical and air agitation, and by straight counter-current decantation. The Merrill zinc-dust precipitation method is used to recover the values, and is preceded by the Crowe vacuum treatment of the solution. The most notable features of the plant are the absence of filters, and the use of short peb mills loaded with steel balls, for fine grinding. As originally designed, the capacity of the mill was to be 200 tons per day, although the grinding end was to be capable of handling double that amount. By adding extra agitators and thickeners and by some alterations to the grinding end, the daily capacity has been raised to 285 tons. This, it is hoped, may be increased to 300 tons during the warm months of the present year. TONNAGE MILLED PER DAY 1917 average 234 Maximum month 272 Minimum month 146 1918 average 253 Maximum month 276 Minimum month 217 As this article primarily deals with plant operations, those interested in the mechanical description are referred to the article by Mr. Otto Wartenweiler,1 the designing engineer, which gives the details and costs of design and construction. The following changes have been made since that article was published:

Jan 8, 1919

By Sidney Sigel, J. Gardner Brooks, Irvin R. Kramer

In 1942 Grossmannl proposed that the hardenability of a steel may be calculated from its chemical composition by considering the base hardenability associated with its carbon content and grain size and multiplying this base by factors for each element present. Since Grossmann's original publication, several investigaton2-6 have reexamined the multiplying factors for the individual elements and in general have found that the multiplying principle is valid. However, some of the individual factor curves developed have been in poor agreement. Inasmuch as the carbon-factor curve obtained by Grossmann was dependent Lipon the factors for all the other alloying elements present in the steel, it logically followed that his results were in need of correction in the light of the new data available for manganese, silicon, and the other alloying elements. Furthermore, in order to avoid the possibility that errors in the manganese, silicon, or other curves might influence the carbon-factor curve, investigation of iron-carbon alloys containing little or no manganese and silicon was necessary. That the effect of carbon on hardenability was greater than indicated by Grossmann is shown by a comparison of the diameters of completely hardened rounds of iron-carbon alloys with the ideal critical diameter calculated from Grossmann's factors. These alloys have a greater hardenability in a finite quench than predicted by Grossmann's factors for an infinite quench (Table I). Among the other important variables that were in need of further investigation were the effect of deoxidation practice on the grain-size correction curves and the effect of stable carbide-forming elements on the depth of hardening. Most Of the work by Kramer, Hafner, and Toleman4 was done on silicon-killed steels. It was not known whether Gross-mann's grain-size correction curves, determined on aluminum-killed steels, was valid when applied to steels with different deoxidation practice. More data on the

Jan 1, 1947

By J. Gardner Brooks, Sidney Sigel, Irvin R. Kramer

In 1942 Grossmannl proposed that the hardenability of a steel may be calculated from its chemical composition by considering the base hardenability associated with its carbon content and grain size and multiplying this base by factors for each element present. Since Grossmann's original publication, several investigaton2-6 have reexamined the multiplying factors for the individual elements and in general have found that the multiplying principle is valid. However, some of the individual factor curves developed have been in poor agreement. Inasmuch as the carbon-factor curve obtained by Grossmann was dependent Lipon the factors for all the other alloying elements present in the steel, it logically followed that his results were in need of correction in the light of the new data available for manganese, silicon, and the other alloying elements. Furthermore, in order to avoid the possibility that errors in the manganese, silicon, or other curves might influence the carbon-factor curve, investigation of iron-carbon alloys containing little or no manganese and silicon was necessary. That the effect of carbon on hardenability was greater than indicated by Grossmann is shown by a comparison of the diameters of completely hardened rounds of iron-carbon alloys with the ideal critical diameter calculated from Grossmann's factors. These alloys have a greater hardenability in a finite quench than predicted by Grossmann's factors for an infinite quench (Table I). Among the other important variables that were in need of further investigation were the effect of deoxidation practice on the grain-size correction curves and the effect of stable carbide-forming elements on the depth of hardening. Most Of the work by Kramer, Hafner, and Toleman4 was done on silicon-killed steels. It was not known whether Gross-mann's grain-size correction curves, determined on aluminum-killed steels, was valid when applied to steels with different deoxidation practice. More data on the

Jan 1, 1947