Search Documents

By James D. McClung, H. J. Gluskoter, M. R. Geer

INTRODUCTION The purpose of coal preparation is to improve the quality of coal to make it suitable for a specific purpose by (1 ) cleaning to remove inorganic impurities; (2) sizing-crushing or screening, or both; or (3) special treatment, such as dedusting. The properties and quantities of impurities in coal are of major importance in the design and operation of steam generating equipment. Al- though boilers are often designed and equipped to use a wide range of coals, no boiler will perform equally well with all types of coals. All coals have certain properties that place limitations on their most advantageous use. These limitations are especially stringent for many of the older installations. Because of a general lowering of quality of raw coal in recent years, the need for coal cleaning has significantly increased. Among the factors contributing to the need for increased coal preparation are (1) increased demand for quality brought on by market and environmental requirements; (2) increased extraneous dilution caused by mine, health, and safety laws; and (3) depletion of the higher-quality coal seams.

Jan 1, 1979

By P. W. George

This paper presents geological data regarding deposits of over 7,500,000 tons of fine-grained sulphide ore in barite gangue. A series of pyroclastics and arkoses was intruded by sills of quartz porphyry in connection with batholithic intrusions of granite 3 miles from Buchans. Gentle folding, with fracturing acid shearing of tuff beds and intruded quartz porphyry, accompanied and followed the intrusion of granite and porphyry. The sulphide-barite mineralization is localized primarily in fractured and sheared tuff beds, but also in the sheared quartz porphyry. Two structures have proved particularly favorable for mineralization-one, the center of an anticline; the other, a series of weak, incompetent tuff beds intruded by thin sills of quartz porphyry and located between strong beds of arkose. During the folding the weak tuff with intruded quartz porphyry was intensely sheared and contorted and subse-quently mineralized by sulphides and barite.

Jan 1, 1937

By E. A. Gulbransen, J. W. Hickman

One of the important factors that determine the resistance of a metal or alloy to further chemical reaction is the structure of the superficial oxide film. A thorough understanding of the physical and chemical structure as well as the stability of the oxide film formed on the surface as a function of time and temperature of the chemical reaction might furnish clues as to the nature of the reaction process and the protective nature of the film. A comprehensive program has been undertaken to study these phenomena. This paper summarizes the structure of the oxide films formed on the metals iron, cobalt, nickel, chromium and copper at temperatures up to 700°C. Before the introduction of the electron diffraction technique, it was necessary to use either direct chemical analyses or X-rav diffraction analyses to determine the nature of the oxide film formed on the metal or alloy. Chemical analyses yields information on the percentages of the several atomic species present in the film while X-ray diffraction analyses yield information on the atomic geometry. In special cases the information obtained may be identical, but in general both viewpoints are necessary. Much of the early work was carried out on the oxidation of bulk samples where thick films were obtained. The products were identified after cooling to room temperature by X-ray diffraction and chemical analyses. Although much useful information has been obtained in this manner. little could be learned about the character of the protective oxides during the period when the films were actually protective. Evidence concerning the chemical structure of thin oxide films has been made possible by the development of the electron diffraction reflection technique. In this method the most fruitful investigations have been made by carrying out the reaction in situ at the temperature at which the film is actually protective. Literature The oxidation of iron has been extensively investigated by X-ray and electron diffraction. Jackson and Quarrelll found that oxide films formed and examined at the same temperature differed considerably from those allowed to cool to room temperature. The results showed that below 400°C the oxide that was stable in intimate contact with iron was Fe³O4; between 515° and 900°C. the stable film was FeO. Above the upper change point of iron the oxide was found to be Fe³O4. From 400' to 515°C., FeO, Fe³O4 or a mixture of the two oxides was found. Recrystallization of the air-formed film below 400' and above 900°C. led to the formation of Fe3O4. In the range where thicker films consisted of FeO, the air-formed film was converted to a new hexagonal oxide not previously described.

Jan 1, 1947

By Robert D. Pike

In November 1939, on behalf of the Harbison-Walker Refractories Co., the author undertook the study of the problem of utilizing the dolomite of northwestern Ohio for the manufacture of calcined magnesia suitable for use in refractories. Grateful acknowledgment is made of the unfailing assistance and encouragement throughout this work from the executive and technical staff of Harbison-Walker Refractories Company. The dolomite of the Niagara formation that is exposed or near the surface of a wide area in northwestern Ohio1 constitutes a vast supply of almost pure dolomite. It offers a virtually unlimited supply of cheap raw material of uniform dependable analysis for the manufacture of magnesia. A typical analysis of dolomite from the vicinity of Luckey, Ohio, follows: Stone Completely Calcined CaO(Sro)a............. 30.35 57.806 Mgo................... 21.55 41.050 SiO2. ................... 0.30 0.572 R2O3................... 0.30 0.572 Ignition loss............. 47.50 a SrO about 0.06 pct. Brines containing magnesium chloride or sea water can be reacted with calcined dolomite to produce magnesia.2'3 In such reactions the MgCl2 of the brine supplies some of the magnesia and the amount of dolomite required is thereby reduced by an equivalent amount, but brines of commercial importance containing magnesium chloride are some distance away from the purest grades of the dolomite of northwestern Ohio. It was decided therefore to concentrate upon the development of a suitable process for separating the lime and magnesia of dolomite, depending upon the dolomite itself as the sole source of magnesia. This would make it possible to place a plant at the dolomite quarry, thus eliminating the cost of transporting the stone and also rendering the calcined magnesia available at a most convenient production point, considering the cost of delivery throughout the steel industry. The selection of a process depending solely upon the dolomite as a source of magnesia also necessarily entails production of the lime content of the dolomite as a by-product. It was recognized that if such a lime by-product could be produced in a suitable form, a plant location in northwestern Ohio would also be advantageous for marketing the lime. The problem, therefore, was the discovery and development of a low-cost process for separating the magnesia and lime of the dolomite of northwestern Ohio and producing each in a form relatively free from the other, and meeting the respective requirements of established markets. A satisfactory solution of this problem has been found, and it is the

Jan 1, 1948

By Robert D. Pike

In November 1939, on behalf of the Harbison-Walker Refractories Co., the author undertook the study of the problem of utilizing the dolomite of northwestern Ohio for the manufacture of calcined magnesia suitable for use in refractories. Grateful acknowledgment is made of the unfailing assistance and encouragement throughout this work from the executive and technical staff of Harbison-Walker Refractories Company. The dolomite of the Niagara formation that is exposed or near the surface of a wide area in northwestern Ohio1 constitutes a vast supply of almost pure dolomite. It offers a virtually unlimited supply of cheap raw material of uniform dependable analysis for the manufacture of magnesia. A typical analysis of dolomite from the vicinity of Luckey, Ohio, follows: Stone Completely Calcined CaO(Sro)a............. 30.35 57.806 Mgo................... 21.55 41.050 SiO2. ................... 0.30 0.572 R2O3................... 0.30 0.572 Ignition loss............. 47.50 a SrO about 0.06 pct. Brines containing magnesium chloride or sea water can be reacted with calcined dolomite to produce magnesia.2'3 In such reactions the MgCl2 of the brine supplies some of the magnesia and the amount of dolomite required is thereby reduced by an equivalent amount, but brines of commercial importance containing magnesium chloride are some distance away from the purest grades of the dolomite of northwestern Ohio. It was decided therefore to concentrate upon the development of a suitable process for separating the lime and magnesia of dolomite, depending upon the dolomite itself as the sole source of magnesia. This would make it possible to place a plant at the dolomite quarry, thus eliminating the cost of transporting the stone and also rendering the calcined magnesia available at a most convenient production point, considering the cost of delivery throughout the steel industry. The selection of a process depending solely upon the dolomite as a source of magnesia also necessarily entails production of the lime content of the dolomite as a by-product. It was recognized that if such a lime by-product could be produced in a suitable form, a plant location in northwestern Ohio would also be advantageous for marketing the lime. The problem, therefore, was the discovery and development of a low-cost process for separating the magnesia and lime of the dolomite of northwestern Ohio and producing each in a form relatively free from the other, and meeting the respective requirements of established markets. A satisfactory solution of this problem has been found, and it is the

Jan 1, 1948

By C. H. Benedict

Largest and most important of the milling plants under construction during the year is the Morenci plant of the Phelps Dodge Corp., in Arizona, where plans are being rushed for production in 1942. Grate mills will be used for fine-grinding, and in the pilot plant, classifiers of the spiral type have the preference for the closed- circuit work. The flotation units will be chiefly of the pneumatic type, with some mechanical units as auxiliaries. The Fagergren, Pan American, and Agitair machines were left in the competition as the year closed. If the absence of European markets for finished products has dislocated the mining industry, fortunately the lack of raw materials required in the beneficiation of ores has not been serious. except possibly as to the inability to import flint grinding pebbles. Some of the less important gold mines still use pebbles for grinding as is also the practice in the comminution of nonmetallics used in various industries. T the Calumet & Hecla in the Lake A Superior copper district pebbles have been used exclusively in open- circuit grinding in the Hardinge mills treating the

Jan 1, 1941

By H. A. Meyerhoff, R. J. Colony

Deposits of iron are widely scattered in the folded Cretaceous rocks and the associated igneous intrusives of Puerto Rico. Most of them are too small for commercial development, but a few have aroused some scientific and economic interest, among them the large body of residual limonite at the west end of the island near Mayagüezl-6 (Fig. 1) and the mixed hematite and magnetite deposit on the southern slopes of the Sierra de Cayey, about four miles north of Arroyo.7"9 Neither of these orebodies has been developed, nor have investigations of the widely distributed deposits of magnetite, which include all the remaining occurrences of iron deserving of economic consideration, proceeded beyond the exploratory stage. With the possible exception of the mixed deposit near Arroyo, the magnetite is directly associated with andesitic and dioritic intrusives, which invade the Cretaceous rock section, and the bulk of it, occurring in calcareous sediments, is clearly of contact-replacement origin. The small deposit on Rio Portugües, north of Ponce, is found in a limestone band near its contact with an andesite dike.10,11 Two deposits of unde-

Jan 1, 1935

By F. Weinberg

It has been suggested, for some time, that the behavior of metals under high-temperature creep conditions is strongly influenced by the behavior of the grain boundaries present in the material. This has led to a number of investigations1-6 in which attempts were made to measure the properties of the grain boundaries themselves, both to determine their contribution to the creep process and to obtain further knowledge of their intrinsic structure and properties. The present investigation was undertaken to extend the observed data under more closely controlled experimental conditions and to attempt to clarify sonie of the discrepancies in the literature. A brief report of the preliminary results has been published.7 EXPERIMENTAL PROCEDURE For the present investigation, controlled orientation specimens were used having plane boundaries which terminated at the specimen surface. Trierys-tal specimens were used instead of the bicrystal type of Puttick and King,' in order to simplify the gripping technique required to apply a shear stress along the boundary. The aluminum used was obtained from the Aluminum Francaise and was of 99.994 pct purity, containing 0.002 pct each of Cu, Fe, and Si. The aluminum tricrystals were grown horizontally from the melt, in graphite boats, and in an argon atmosphere, following the technique developed by Chalmers.' The orientation of the tricrystals was controlled by using seed crystals separated by mica inserts. Thermal conditions were adjusted to produce tricrystals having boundaries which were macroscopically straight, parallel to the growth direction, and perpendicular to the top surface. Following growth, the tricrystals were carefully cut with a jeweller's saw to the test specimen shapes shown in Fig. l(a) and l(b). In Fig. 1(a), the boundaries subjected to shear stresses are indicated AB and CD: Points A and C are the ends of the mica inserts separating the seed crystals; points B and D are at lateral cuts made in the specimen. It was found that the slots left by the mica inserts at A and C had to be enlarged slightly, by cutting, to ensure that the boundary terminated freely at these points. A shear stress was applied to the boundarks by gripping the upper two legs in file-faced Inconel grips and suspending a weight from the lower part of the specimen held in similar grips, as shown schematically in the diagram. The test specimens shown in Fig. 1(b) were cut from long

Jan 1, 1959

By H. A. Meyerhoff, R. J. Colony

Deposits of iron are widely scattered in the folded Cretaceous rocks and the associated igneous intrusives of Puerto Rico. Most of them are too small for commercial development, but a few have aroused some scientific and economic interest, among them the large body of residual limonite at the west end of the island near Mayagüezl-6 (Fig. 1) and the mixed hematite and magnetite deposit on the southern slopes of the Sierra de Cayey, about four miles north of Arroyo.7"9 Neither of these orebodies has been developed, nor have investigations of the widely distributed deposits of magnetite, which include all the remaining occurrences of iron deserving of economic consideration, proceeded beyond the exploratory stage. With the possible exception of the mixed deposit near Arroyo, the magnetite is directly associated with andesitic and dioritic intrusives, which invade the Cretaceous rock section, and the bulk of it, occurring in calcareous sediments, is clearly of contact-replacement origin. The small deposit on Rio Portugües, north of Ponce, is found in a limestone band near its contact with an andesite dike.10,11 Two deposits of unde-

Jan 1, 1935

By C. E. Wood, E. P. Barrett, T. L. Joseph

The invention of the Bessemer converter process in 1856 added great impetus to the manufacture of steel and is one of the outstanding contributions to process metallurgy. Although the process of refining pig iron by passing air through the molten metal bears the name of Henry Bessemer, it should be mentioned in passing that William Kelley of Eddysville, Ky., worked on the process as early as 1847. Kelley was granted a patent on the process in 1857, inasmuch as he was able to prove priority in discovery.' After considerable litigation in 1865 the respective interests of Kelley and Bessemer were combined. On Sept. 10, 1856, Robert Mushet of England obtained his first patent on the application of manganese to cast steel. Mushet anticipated trouble in purifying iron by passing currents of air through it: His patent specified that steel made in this way often contained flaws and was red short or cold short. Mushet understood the refining of pig iron into steel well enough to realize the difficulties likely to be cncountered from oxidation of the iron. Mushet was not only an inventor; he was also an investigator. He understood the principle of selective oxidation which takes place in the converter process, and he realized therefore that the remedy for over-oxidation was attainable if a suitable metal could be found at a reasonable cost and in sufficient quantities. His first experiments were made in small crucibles holding a few ounces of metal. Later his work was conducted on a larger scale and with complete success. Manganese had been used in making steel a quarter of a century before the converter

Jan 1, 1927

Jan 1, 1924

Part 1. Coal Part 2. Industrial Minerals

Jan 3, 1977

By M. F. Hawkes, R. F. Mehl

The rate of isothermal transformation of austenite to pearlite depends upon the rate of nucleation, N, and the rate of growth, G, of pearlite in austenite. Values of N are given in terms of the number of nuclei forming in unit time per unit grain boundary area of unreacted austenite; values of C are given in terms of the linear rate of radial growth. Variations in the isothermal rate with temperature result from variation of N and G with temperature. Depth of hardening of a steel depends fundamentally upon values of N and G; changes in carbon and alloy content effect changes in N and G and thus affect depth of hardening. Quantitative studies are available on N and G for the formation of pearlite in plain carbon eutectoid steels.3 Systematic studies in this field are necessary if the phenomena are to be well enough known to furnish a proper basis for full rationalization and for theory. Accordingly, the studies are continuing, both with respect to the effect of alloying elements upon the values of N and G in the formation of pearlite and to the values of N and G for the formation of ferrite in hypoeutectoid steels. The present paper is the first relating to the effect of alloying elements upon the values of N and G for pearlite. It offers special interest since cobalt is known to have an anomalous effect upon the rate of formation of pearlite, accelerating it, whereas all other elements retard it.4 It will be shown that cobalt increases both N and G for pearlite and that this effect is inherent in the Fe-Co-C system and not dependent upon factors relating to austenite heterogeneity nor upon any recognizable adventitious factor. Inasmuch as the rate of diffusion of carbon in austenite and the interlamellar spacing of pearlite are variables related to G and possibly to N (in a manner not yet certain), measurements of the effect of cobalt upon them are also reported here. In the course of the work, measurements were made on the effect of cobalt upon the marten-site temperature and these are given. COBALT AS AN ALLOYING ELEMENT IN STEEL Properties of Cobalt Cobalt resembles iron more closely than does any other chemical element. Its atomic number is 27, hence it is the element immediately following iron in the periodic system. The two differ in atomic structure only in the fact that cobalt contains seven electrons instead of six in the third, or transition, level of .the third shell. The next shell, which is the

Jan 1, 1948

By C. A. Heiland W. E. Pugh

The principle underlying the majority of magnetic intensity variometers is a comparison of the force to be measured with another force of known magnitude. The known force may be (a) of a magnetic nature, such as magnetic fields produced by magnets or coils, or (b) of a mechanical nature, such as (1) the elastic forces of wires, or (2) the force of gravity, such as employed in bifilar magnetometers and magnetic balances. In instruments of such type, usually a magnetic system is employed, free to move about either a horizontal or vertical axis, on some sort of a suspension. If the earth's magnetic field alone were present, such a system would adjust itself into the direction of the field or that of its components. Owing to the simultaneous action of the comparison force, however, the magnetic needle assumes a position that differs from the direction of the magnetic force; for all such instruments, the angle of deflection is given by tan = FIX, where F is the known and X the unknown earth magnetic force component. In other words, the magnetic system merely serves as an "indicator" for the position of balance of the two forces. Considering the matter from this point of view, it is not immediately obvious why the temperature of such a magnetic system should modify the results. In magnetic instruments, we may distinguish two different effects of temperature: (1) a magnetic effect and (2) a mechanical effect. The first is due to the fact that the magnetic moment of a magnet drops with an increase in temperature. This drop is characterized by the temperature coefficient of the magnetic moment (see equation 1). The second effect is due to the change in the torsion of suspension wires with temperature or to the expansion of lever arms of masses acting on magnetic balances.

Jan 1, 1934

By M. F. Hawkes, R. F. Mehl

The rate of isothermal transformation of austenite to pearlite depends upon the rate of nucleation, N, and the rate of growth, G, of pearlite in austenite. Values of N are given in terms of the number of nuclei forming in unit time per unit grain boundary area of unreacted austenite; values of C are given in terms of the linear rate of radial growth. Variations in the isothermal rate with temperature result from variation of N and G with temperature. Depth of hardening of a steel depends fundamentally upon values of N and G; changes in carbon and alloy content effect changes in N and G and thus affect depth of hardening. Quantitative studies are available on N and G for the formation of pearlite in plain carbon eutectoid steels.3 Systematic studies in this field are necessary if the phenomena are to be well enough known to furnish a proper basis for full rationalization and for theory. Accordingly, the studies are continuing, both with respect to the effect of alloying elements upon the values of N and G in the formation of pearlite and to the values of N and G for the formation of ferrite in hypoeutectoid steels. The present paper is the first relating to the effect of alloying elements upon the values of N and G for pearlite. It offers special interest since cobalt is known to have an anomalous effect upon the rate of formation of pearlite, accelerating it, whereas all other elements retard it.4 It will be shown that cobalt increases both N and G for pearlite and that this effect is inherent in the Fe-Co-C system and not dependent upon factors relating to austenite heterogeneity nor upon any recognizable adventitious factor. Inasmuch as the rate of diffusion of carbon in austenite and the interlamellar spacing of pearlite are variables related to G and possibly to N (in a manner not yet certain), measurements of the effect of cobalt upon them are also reported here. In the course of the work, measurements were made on the effect of cobalt upon the marten-site temperature and these are given. COBALT AS AN ALLOYING ELEMENT IN STEEL Properties of Cobalt Cobalt resembles iron more closely than does any other chemical element. Its atomic number is 27, hence it is the element immediately following iron in the periodic system. The two differ in atomic structure only in the fact that cobalt contains seven electrons instead of six in the third, or transition, level of .the third shell. The next shell, which is the

Jan 1, 1948

By J. H. Hollomon, L. D. Jaffe

The hardenability concept has become widely used during the last few years for the choice and substitution of steels. Before the work of Grossmann,1 the systems for predicting hardenability from chemical composition could be used only over a narrow range of composition. Grossmann introduced a comprehensive system, which has been effective in calculating the hardenability of most types of moderate or low-alloy steels. However, occasions often arise that require the calculation of the hardenability of high-alloy steels from their chemical compositions. Experimental determinations of the hardenabilities of such steels indicate that the Grossmann system predicts much greater hardenabilities than are realized. The fact that cases do arise in which the Grossmann method does not apply indicates that the fundamental hypothesis of the system may not be generally applicable. It seems advisable to re-examine not only Grossmann's system but also the concept of hardenability itself. Hardenability If steel parts are to possess a martensitic structure after quenching, they must first be austenitized and then cooled through the pearlite and bainite transformation ranges sufficiently rapidly to avoid the formation of pearlite, bainite, and pro-eutectoid products.* If, on cooling, these transformations are avoided, the resulting structure can consist only of martensite (and retained austenite). The hardenability of a steel is measured in terms of the severity of the cooling conditions necessary to avoid the pearlite and bainite transformations. The less rapid is the cooling necessary to prevent the formation of bainite and pearlite, the higher is the hardenability. The pearlite and bainite reactions appear to be differently affected by the alloying elements. Not only is this indicated by the published isothermal transformation data, but recent work by Zener2 affords a rational interpretation of the differing effects of the alloying elements. Manganese,3 for example, appears to decrease the rates of the pearlite and bainite transformations by equal percentages, while molybdenum45 is approximately 10,000 times more effective in retarding the pearlite than in retarding the bainite transformation, on the basis of isothermal measurements. In some steels, the formation of bainite restricts the formation of martensite while

Jan 1, 1947

By L. D. Jaffe, J. H. Hollomon

The hardenability concept has become widely used during the last few years for the choice and substitution of steels. Before the work of Grossmann,1 the systems for predicting hardenability from chemical composition could be used only over a narrow range of composition. Grossmann introduced a comprehensive system, which has been effective in calculating the hardenability of most types of moderate or low-alloy steels. However, occasions often arise that require the calculation of the hardenability of high-alloy steels from their chemical compositions. Experimental determinations of the hardenabilities of such steels indicate that the Grossmann system predicts much greater hardenabilities than are realized. The fact that cases do arise in which the Grossmann method does not apply indicates that the fundamental hypothesis of the system may not be generally applicable. It seems advisable to re-examine not only Grossmann's system but also the concept of hardenability itself. Hardenability If steel parts are to possess a martensitic structure after quenching, they must first be austenitized and then cooled through the pearlite and bainite transformation ranges sufficiently rapidly to avoid the formation of pearlite, bainite, and pro-eutectoid products.* If, on cooling, these transformations are avoided, the resulting structure can consist only of martensite (and retained austenite). The hardenability of a steel is measured in terms of the severity of the cooling conditions necessary to avoid the pearlite and bainite transformations. The less rapid is the cooling necessary to prevent the formation of bainite and pearlite, the higher is the hardenability. The pearlite and bainite reactions appear to be differently affected by the alloying elements. Not only is this indicated by the published isothermal transformation data, but recent work by Zener2 affords a rational interpretation of the differing effects of the alloying elements. Manganese,3 for example, appears to decrease the rates of the pearlite and bainite transformations by equal percentages, while molybdenum45 is approximately 10,000 times more effective in retarding the pearlite than in retarding the bainite transformation, on the basis of isothermal measurements. In some steels, the formation of bainite restricts the formation of martensite while

Jan 1, 1947

By L. S. Darken

IT has been known for sometime that in an ionic lattice, such as that of Ag2S or FeO, the migration velocity of the anion may differ markedly from that of the cation, the cation being usually the more mobile. It has been shown, for example, that during the formation of silver sulfide tarnish on silver, the tarnish layer grows principally by the motion of silver cations through an essentially stationary silver sulfide lattice. Similarly, the growth of wüstite scale on iron proceeds principally by motion of iron ions, this being accomplished with the aid of vacant iron lattice sites into which the iron may readily move. Likewise investigations of solid solutions of various salts show that there is usually considerable difference in the mobility of the different cations. Measurements of the mobility of various metals in liquid mercury indicate that the various metals move at different rates relative to the mercury. In view of the foregoing it seems reasonable to suppose that when any single phase solution is acted upon by a field, the atoms of different elements respond in different ways; in particular, that the force arising from a particular concentration gradient in a binary alloy would cause the atoms of one component to move with a drift velocity which is in general different from that of the atoms of the other component. The recent experiments of Smigelskas and Kirkendall1 support this viewpoint, since they found, in essence, that during diffusion in alpha brass zinc moves appreciably faster than copper. This was evidenced by the relative motion of inert molybdenum wires. Such a phenomenon is incompatible with the place interchange theory of diffusion proposed by several authors, most recently by Birchenall and Mehl.2 This theory has, however, also been questioned3.4 for other reasons, principally because of the high energy required for direct atomic interchange. The rather large difference between self-diffusivity, as determined by tracer technique, and mutual diffusivity, as determined with the aid of another element at low concentration, might also be interpreted as favoring the above idea; however, Birchenall and Mehl have pointed out that there is another possible interpretation of this difference; this is discussed later. A rather interesting and pertinent observation was made by Schwartz,5 who noticed that tungsten lamp filaments, heated by direct current, commonly fail by necking down in the region at the temperature gradient near the positive end, with a concomitant swelling at the corresponding position near the negative end. He introduces considerable auxiliary evidence to show that this phenomenon is occasioned by the motion of tungsten cations which migrate in the high temperature region from the positive end toward the negative end. The mechanism of this migration is not clearly understood. If, however, this experimental evidence be accepted, we are forced to conclude that alloying elements in the tungsten may migrate by the same or a similar mechanism, whatever it may be, at a greater or lesser rate, thus giving rise

Jan 1, 1948

By Allan J. Clark

It is nearly three years since the metallurgy of the Homestake ore was discussed with considerable thoroughness, in a paper1 read before the Institution of .Mining and Metallurgy. Certain changes have been made in this period which are perhaps of sufficient interest to justify a brief description, and it is chiefly with such details and miscellanies that this paper will deal. In the circumstances, a certain amount of repetition is inevitable, but matter treated of in the former paper will be referred to here only when it is necessary for the sake of coherency. For full descriptions of equipment and technique, the former paper should be consulted. The mineralized slates and schists which constitute the ore vary considerably in composition, but the unoxidized ore, perhaps constituting the major part of the reserves, contains either chlorite or hornblende (cummingtonite), with quartz, carbonates of lime, magnesia and iron, and arsenopyrite, pyrite, and pyrrhotite. Ferrous minerals predominate, and this fact has been an important factor in determining the metallurgical treatment. With one or two exceptions the minerals noted are of relatively high specific gravity, and the ore as a whole is exceptionally heavy, many determinations giving an average specific gravity of 3.00. This high specific gravity presents one decided advantage, when the cost of treatment is compared with operations elsewhere, in that the ton, almost universally the basic unit, represents a volume probably less by 10 per cent. than that of many gold ores. On the other hand, this high gravity renders more difficult the discharge of pulp from mortars, its distribution on amalgam tables, and its transportation in launders. In the same way, as attesting the usual balance of such variations of different ores, it may be noted that the needle-like fibers of hornblende (cummingtonite), interlacing throughout the mass, render the ore more difficult to crush than would be anticipated, but on the other hand assist

Jan 1, 1916

By R. A. Hadfield

It seems a specially fitting opportunity to present a paper on the alloys of iron and aluminum at the New York meeting of this Institute, owing to the fact that America has, more than any other country, originated and developed the manufacture of cheap aluminum. The Cowles, Castner, and Hall systems have all originated in the ever-busy brain of our cousin across the water. The problem of cheaply producing this valuable metal has been a difficult one, but to the writer it seems that the more arduous the task the greater the delight with which our American friend attempts to overcome the difficulties surrounding it, and the more vim he throws into the work. Another and equally striking proof of this is to be found in the recent appearance of the already wellknown remarkable work, The Mefallurgy of Steel, by Mr. H. M. Howe, of the Institute of Technology, Boston, Mass. It is to be hopel that this Institute will not be slow to recognize by some special mark its appreciation of this signally valuable and original work. The writer has been led to describe the following experiments, believing that so far no full and exact report has yet been presented to this Institute as to the effect of aluminum alloyed or combined with the metal iron. It has been a special object to make the material as far as possible a true alloy or combination of aluminum and iron, with as small quantities as possible of other disturbing ingredients, such as silicon, manganese, etc. In the material described in these experiments, the total amounts of other elements present (sulphur and phosphorus being disregarded as present in such small quantities) do not exceed about 0.5 per cent. Such material may therefore be probably taken as fairly illustrative of the effect of the metal aluminum upon iron. Since completing the experiments the writer

Jan 1, 1891