Search Documents

By G. W. P. Rengstorff, L. E. Olds

High purity molybdenum ingots containing controlled amounts of a single impurity element (oxygen, nitrogen, or carbon) were prepared. These ingots were tested for ductility by bending test specimens at various temperatures. The relationship between the plastic behavior of the ingots and their chemical composition has been determined. MANY proposed applications for molybdenum require ductility at or near room temperature. At the present time, it is possible to obtain wrought molybdenum with considerable ductility only if special fabrication techniques are used to control the grain structure. Starting with are-cast or powder metallurgy ingots, the usual methods for obtaining ductility rely on fabrication procedures that result in fibered microstructures in the finished product. Recently, it has been found that the ductility of either powder metallurgy or are-cast molybdenum can be improved by uniform recrystallization of the metal to a very fine equiaxed grain structure.' The need for a fibered or a fine grained structure may limit the practical usefulness of molybdenum. For example, welding. which may be used in fabricating the metal, generally produces coarse grained structures that lead to brittleness. This applies, certainly, to currently available commercial molybdenum. Although commercial molybdenum is brittle when the grains are coarse, it has been shown experimentally that fine grained structures are not always essential for ductility. For instance, as-cast molybdenum with a coarse columnar grain structure is ductile if it is sufficiently pure.' Because high purity cast molybdenum has good ductility even when coarse grained, it is probable that the brittleness in coarse grained commercial molybdenum is caused by the impurity content of the metal. Although the general effects of impurities on the cold ductility of molybdenum have been known in a qualitative manner for some time, no quantitative evaluation of these effects has been available. The present investigation was made in order to determine more accurately the effects of oxygen, nitrogen, and carbon on the cold ductility of cast molybdenum. Oxygen has long been known to be detrimental to ductility, although the minimum amount which will embrittle molybdenum has been open to speculation. Parke and Ham" showed that ingots with oxygen contents above 0.003 pct could not be forged. Maringer and Schwope have described the embrittle-ment of molybdenum wire by oxygen. A discussion on the effects of heat treatment on the distribution of oxygen in molybdenum has been given by Perry, Spacil, and Wulff." Although nitrogen would also be expected to have harmful effects on ductility, no extensive work has been done previously to determine whether this is so. However, Tury and Krausz" found that wires presumably with less than 0.007 pct N were brittle. Carbon is added to commercial cast molybdenum for deoxidation. Parke and Ham" have shown that molybdenum containing as much as 0.06 pct C could be forged if the oxygen was kept below 0.003 pct. Also, Bruckart and others' found that the room temperature ductility of sintered molybdenum improved with carbon contents up to 0.84 pct. However, Rengstorff and Fischer' found that residual carbide particles in cast molybdenum apparently had an unfavorable effect on room temperature ductility.

Jan 1, 1957

By W. A. Doble

Opinions differ as to whether the water-wheel almost universally known as the Pelton type belongs to the impulse, the tangential, the reactive, the jet or the percussion class, or to a cross between two or more of these classes. The fact is, that for an almost infinitesimal part of a second the axis of the jet of water strikes the bucket of this wheel at a true tangent to its base-line. The percussion of the water, striking the bucket, imparts an impulse to the wheel, causing rotation; and generally the bucket is so shaped that the direction of the jet is

Jan 1, 1900

By F. Lynwood Garrison

It is not intended to make in the present paper any deduction or to formulate any theories from the results obtained by experiments. The further expenditure of considerable time and labor would be required to obtain a sufficient basis for positive assertions as to the microscopic structure of the different varieties of iron and steel, and the structural changes which take place in them. It is therefore my purpose at this time to offer simply a synopsis of the general results arrived at in a few months' work, a brief description of apparatus used, and a few hints as to the preparation and preservation of the material which it is intended to investigate. The study of the microscopic structure of iron and steel is not altogether new. Some attention has been given it in both England and Germany. But the foreign publications on the subject have thus far been confined, so far as I am aware, to two papers, one by Herr Martens, of Berlin, contributed to the Verein zur Befoerderuny des Gewerbfleisses and the other a lecture by Dr. H. C. Sorby of Sheffield. Dr. Sorby, it seems, was induced to investigate the subject as bearing on the structure of meteoric iron ; and the results he obtained are certainly very interesting. At the Boston meeting of this Institute, in February, 1883, Mr. J. C, Bayles called attention to the subject in a neat and exceedingly interesting paper, in which the work of Messrs. Martens and Sorby was summarized,* and original suggestions were added. It is at present difficult to say what will he eventually the practical value of the microscope, thus employed, in the sciences of engineering. The role which it seems most likely to play is that of' an adjunct to the testing-machine, and not (as some have supposed) a rival to the chemical laboratory. That it will be a most valuable accessory seems, to say the least, highly probable. I need hardly go at length into the details of preparing the material for examination. Mr. Bayles has described the process in such a plain and comprehensive manner that if his instructions are

Jan 1, 1886

[NORTH AMERICA UNITED STATES ALABAMA AUBURN Sturm & O'Brien, Consult. Engrs. °Sturm, Rolland G. BESSEMER Granger, W. C. BIRMINGHAM Air Reduction Sales Crockett, John M. Amer. Cast Iron Pipe Co. Carter, Sam F., Jr. Donoho, C. K. Anderson Elec. Corp. Davis, Moss V. J. B. Clow & Sons Neptune, Maurice D. Connors Steel Div. °Sandelin, Robert W. Hayes Aircraft Corp. Ricketts, W. E., Jr. Willhelm, A. Clyde, Jr. McWaine Cast Iron King, O. H. Worthington, B. W. Shook & Fletcher Sup. Co. Gearhart, Thomas A. Southern Res. Inst. Dismukes, Edward B., Wheelahan, Edmund J. Thomas Foys Miller, Ralph M. Union Carbide Metals, Co. Brandler, Edgar A. U. S. Pipe & Fdry. Co. Clay, Donald H. Unaffiliated Berg, H. A. Caldwell, H. A. Gilmer, H. U. Harris, Thomas H. Templeton, J. B.]

Jan 1, 1961

By G. Howell Clevenger

FORMERLY great divergence of opinion existed in regard to the influence of copper in steel, as affecting its various physical properties. More recently the investigations of Stead,1 Breuil,2 Wigham,3 Burgess and Aston,4 Ball and Wingham,5 Miiller,6 Dillner,7 and others have shown fairly good agreement in the major points. Copper steel has been shown by these investigators to possess special properties which make it valuable for certain uses. The general range of composition of the useful alloys of copper and iron, and of copper, iron, and carbon, has been quite definitely established, for the former by Burgess and Aston,8 and for the latter by Breuil 9 and Stead.10 Stead 11 has removed one difficulty in reconciling certain of the earlier data by calling particular attention to the influence of carbon in copper steels. Another point which caused confusion in the earlier investigations, particularly in regard to " red-shortness," was the presence of sulphur. Failure to note the presence of sulphur often led to attributing " red-shortness " to the presence of small amounts of copper. Turner 12 has called attention to the fact that where copper exists in an iron ore it often occurs as the sulphide, so that the presence of copper in steel made from such ores might also, necessarily, mean the presence of sulphur. It is evident that the effect in this case might be quite different than where pure copper was added.

Jan 10, 1913

By R. M. Rose, K. A. Jones

Resistive measurements ulere made on superconducting niobium single crystals in transverse magnetic fields. Crystals were grouln in both high and ulfrahigh vacua, doped with stnall quantities of oxygen, and annealed in ultrahigh vacua at temperatures from 900' to 1350°C. Maxima in the fluxoid pinr~ir~g force were observedfor the [100] and [210] directions. The increase of the critical current density with dissoved oxygen was seen to saturate at relatively low concentration. This behavior, and the variation of J, and residual resistivity (as a function of oxygen content and annealing) of both clean and dirty gassy) crystals, is seen as a consequence of the formation of clusters with (210)~b habit planes and (200)ffo common boundaries. These suboxide clusters are apparenlly stable at high temperatures and very low oxygen concentrations. It is generally known that dissolved oxygen at concentrations well below the solubility limit sharply increases the critical current density of superconducting niobium.' Such a result would not be expected if Nb-0 solutions were random, not even as the result of segregation on the scale usually encountered in solid solutions. According to the Kim-Anderson theory of flux creep,' the critical transport current density is determined by the pinning force Fp associated with some feature of the microstructure. As the Lorentz force. a or (J X R), of the transport current in the magnetic field approaches Fp, flux creep and then flux flow occur. The pinning force is expected to be quite small if the heterogeneity involved is significantly smaller than tte range of coherency which for niobium is circa 250~.~ Although the strain field of an individual oxygen atom in the niobium lattice is relatively large, it does not seem plausible that individual atoms could be so effective as to account for the data. Also, ~ramer~ found that straining and strain aging specimens containing small amounts of oxygen on occasion decreased the residual resistivity. A possible explanation for the above behavior may be found in the work of van Ooijen and van der Goot,= who found that annealing changed J, for niobium foils containing oxygen, and they attributed the changes to ordering of the oxygen atoms. This phenomenon has been observed by other investigators using X-ray and PROCEDURE Cylindrical 4-in.-diam niobium single crystals with axial orientations [ill], [110], [112], and [oo~] were grown from pure niobium, see Table I for analysis, in an ion-pumped ultrahigh-vacuum system using the electron beam floating zone technique. Total pressure during growth was lo-'9 torr: the oxygen partial pressure was less than lo-" torr, as determined by a mass spectrometer. These crystals will be referred to as the "clean" crystals. Similar crystals were also grown in another system at a pressure of 5 X 10"6 torr. These crystals will be referred to as the "dirty" crystals. Specimens 14 in. long were cut from the as-grown crystals and one end was polished down to no. 600 carbide paper smoothness. A back-reflection Laue photograph was then taken in order to fix the crystallo-graphic directions transverse to the crystal. The critical current density J,, the current density necessary to produce a voltage drop of 1.0 pv between voltage leads placed a in. apart, was determined as a function of the magnitude and direction of the transverse magnetic field and of the oxygen concentration. The technique and experimental arrangement was essentially similar to that of Tedmon et al.' In the remainder of this paper, the azjmuthal angle $ for the field H is referenced to the [ I101 direction in all four crystals, and oxygen was added in small equal increments by anodization and annealing.7 The resistivity ratio, RR, of the resistance at room ternperature to that at 4.2"K (H =7.00 kG) was determined as well.

Jan 1, 1970

By J. G. Baragwanath

CUBA'S lateritic iron ores, occurring on the northern coast of that island, though known to the Spaniards. did not receive any general attention until the close of the Spanish-American War. Preliminary studies of these deposits at that time indicated that the limonite contained small percentages of nickel and chrome, and it ryas subsequently discovered that although the average nickel content was only approximately 0.6 per certain limited areas of ore were suffiniently high in nickel to be considered commercial provided a suitable process fur its recovery could be developed. Early in 1937, Pardners Mines Corp. began a series of investigations which led to the development of such a process. Coincidentally, this company acquired option' on certain properties in the Levisa Bay and Moa Bay regions and conducted a systematic campaign of exploration by test pits and hand-auger holes in the course of which an aggregate of 90.000.000 tons of ore was developed in eight deposits.

Jan 1, 1945

By Guillermo Zuloaga

The iron deposits of the Imataca Range of Venezuela, which occur along the Orinoco River, in the northern border of the Guayana Highlands, have lately attracted attention on account of their economic possibilities. Many deposits occur in this area; some of slight economic importance and others that may rank with the largest masses of high-grade iron ore of the world. The geology and the character of the ores seem to be remarkably similar to those of the large iron deposits of Brazil. In the investigation of the Venezuelan deposits a definite relationship has been found between the mineralization of the large orebodies and igneous intrusions, especially norites and granites. The following paper is the result of a field and laboratory investigation of the ore deposits. The field work was done during the months of February and March of the year 1929, partly in the company of Prof. W. H. Newhouse. The laboratory studies have been made in the Massachusetts Institute of Technology, under the supervision of Professor Lindgren and Professor Newhouse. GENERAL GEOLOGY OF GUAYANA HIGHLANDS General Geography and Physiography The Sierra de Imataca proper occupies a narrow belt along the south bank of the Orinoco River, in the northeastern part of the State of Bolivar and in the western part of the Delta Amacuro Territory of Venezuela. The State of Bolivar is generally known as the Venezuelan Guayana, as it forms part of the same physiographic province of the Guianas and northeast Brazil. In general the Venezuelan Guayana is an extensive plateau, sloping gently towards the Orinoco River to the north and towards the Atlantic Ocean to the east. In the northern part mountains are rare, and consist mainly of elongated low hills. Towards the British Guiana-Brazil boundary, table mountains with vertical cliffs are found forming the ranges of Parima, Roraima and Pacaraima. General Geology The Guayana Highlands are the northern extension of the Brazilian Archean shield. Only a few scattered masses of sediments remain on its

Jan 1, 1935

By Guillermo Zuloaga

The iron deposits of the Imataca Range of Venezuela, which occur along the Orinoco River, in the northern border of the Guayana Highlands, have lately attracted attention on account of their economic possibilities. Many deposits occur in this area; some of slight economic importance and others that may rank with the largest masses of high-grade iron ore of the world. The geology and the character of the ores seem to be remarkably similar to those of the large iron deposits of Brazil. In the investigation of the Venezuelan deposits a definite relationship has been found between the mineralization of the large orebodies and igneous intrusions, especially norites and granites. The following paper is the result of a field and laboratory investigation of the ore deposits. The field work was done during the months of February and March of the year 1929, partly in the company of Prof. W. H. Newhouse. The laboratory studies have been made in the Massachusetts Institute of Technology, under the supervision of Professor Lindgren and Professor Newhouse. GENERAL GEOLOGY OF GUAYANA HIGHLANDS General Geography and Physiography The Sierra de Imataca proper occupies a narrow belt along the south bank of the Orinoco River, in the northeastern part of the State of Bolivar and in the western part of the Delta Amacuro Territory of Venezuela. The State of Bolivar is generally known as the Venezuelan Guayana, as it forms part of the same physiographic province of the Guianas and northeast Brazil. In general the Venezuelan Guayana is an extensive plateau, sloping gently towards the Orinoco River to the north and towards the Atlantic Ocean to the east. In the northern part mountains are rare, and consist mainly of elongated low hills. Towards the British Guiana-Brazil boundary, table mountains with vertical cliffs are found forming the ranges of Parima, Roraima and Pacaraima. General Geology The Guayana Highlands are the northern extension of the Brazilian Archean shield. Only a few scattered masses of sediments remain on its

Jan 1, 1935

By Donald C. Barton

The theory of gravitation is based on Newton's law that any two bodies exert a mutual attraction which is proportional to the product of their masses and inversely proportional to the square of the distance between them; i. e., A = KMRm2 (1) where K is a constant, M and m are the respective masses of the two bodies, and R the distance between them. In the earth's gravitational system, the earth is one of the bodies; the other may be any body within or without the earth. In theoretical discussions and calculations,in regard to gravity, that other body usually is taken as a unit of mass: in the C:. C:. S. system, a body of one gram in mass. Gravity and Level Surfaces Gravity is defined in geophysics as the force of attraction exerted by the earth, towards itself, on a body of unit mass. The intensity of gravity is usually expressed in dynes of force or in centimeters of acceleration In geophysical work in America, most commonly it is expressed in dynes (per gram) with the "per gram" understood and not directly expressed. In geophysical work in Europe, most commonly it is expressed in centimeters per second per second (cm. /sec.2) and less commonly lrierely as centimeter-gram-second units (c. g. s). At sea level, the intensity of gravity amounts very nearly to 980 dynes. The vertical is the direction along which the attraction of gravity is exerted at any point. In most cases, it is very nearly, but not quite, perpendicular to the earth's surface. The path that would be taken by a body falling freely through space toward the earth is vertical at each point and may be spoken of also as ('the vertical," or as the line of the vertical, or as a line of force of gravity. At the earth's surface it comrrlonly is very nearly, but not quite, a straight line.

Jan 1, 1929

By R. Ebeling, M. F. Ashby

The paper is in two parts. The first develops the formulae and method needed to calculate the size, nu)nber, spacing, and volume fraction of hard or inert particles in the interior of a specimen from measurernents made on an extraction replica; throughout, the spread of- particle sizes in a single specimen is taken into account, and the extraction efficiency of the replica is considered. A method for testing whether the particles are randotnly distributed in space is described, and the spacing of randomly distributed particles is discussed. The second Part describes the application of the method to copper containing spherical particles of silica; the description includes an estimate of the errors involved, and a comparison of this with alternative methods. All parameters except uolume fraction can be determined satisfactorily, and the method offers advantages over other electron-,rzicroscopic techniques when dealing with hard particles in a softer matrix, or inert particles in a chem-ically less inert matrix. 1 HE experimental measurement of sizes and numbers of discrete particles of a second phase embedded in a matrix material from opaque, plane sections has been considered by many authors, notably by Fullman.' It is assumed that, when the specimen is sectioned, the particles are also sectioned, so that the diameters of the circles of intersection of particles with the plane of the cross section ("surface diameters") are measured. It is difficult to derive the distribution of true particle diameters ("volume diameters") from measurements of the distribution of "surface diameters" on a plane section. The measurement of size and numbers of small second-phase particles by transmission electron microscopy through thin foils of matrix containing the particles has been described by Cahn and ~uttin~' and by ~illiard.~ Because of overlap and the fact that particles which intersect the foil surface may be sectioned whereas those in the bulk of the foil are not, it is again difficult to measure the true distribution of particle sizes. The use of replicas for this sort of measurement has not been analyzed in detail. A replica made from an opaque cross section, thus replicating the circles of intersection of particles with the plane of section, is analyzed by Fullman's method and suffers from the same difficulties. Under certain circumstances, however, extraction replicas can be used, and offer a special advantage in that they make the determination of the true distribution of particle diameters particularly simple. It is the purpose of this paper to describe this extraction replica method. Consider the example of an alloy consisting of SiOz particles, whose mean diameter is about 1000A, dispersed in a copper matrix. When the alloy is sectioned and mechanically polished, the particles are not sectioned, because they are much harder than the matrix, and so will be either left in the surface or pulled out whole, and because the particle size is smaller than the abrasive size of even the finest abrasive. The particles are chemically inert in solutions which chemically etch or electropolish the matrix, so that chemical treatments do not section the particles either. (Experimental measurements of particle shape in this alloy confirm this—truncated particles are never seen.) Small, hard or inert, particles are therefore not sectioned when the specimen is sectioned and polished. An extraction replica taken from this polished surface shows the true "volume" diameter of each extracted particle; the distribution of diameters seen on the replica is the surface distribution of true "volume" diameters, and the volume distribution of true "volume" diameters is easily derived from it. The extraction replica method is not subject to the difficulties associated with sectioning of particles, and avoids the problem of overlap from which the transmission method suffers. The method is well-suited for studying hard particles in a soft matrix. Examples are provided by internally oxidized alloys, oxide-dispersion strengthened metals like T.D. Nickel, and carbides, nitrides, and strong intermetallic compounds in metals. It should be possible to adapt polishing techniques in alloys containing softer but inert particles to avoid sectioning the particles (say by electropolishing or etching). The method is tested and illustrated in Sections 8 and 9 by applying it to a dispersion of spherical SiO2 particles in a copper matrix. I) SYMBOLS Symbols are defined where they first appear in the text. Volume fractions of particles are denoted by the symbol f, particle diameters by x, center-to-center particle spacings by D, and numbers of particles by N. Mean particle diameters and standard deviations about these means are denoted by x and a. Both arithmetic (subscript A) and geometric (subscript G) means are employed. In this paper we measure the distribution of true diameters of particles which touch or pass through a random-plane section of the specimen. We may want to know the distribution of particle diameters in the

Jan 1, 1967

By Vasily P. Muravjev, Gennady I. Razgildeev

The theory of reliability is a powerful mathematical tool for determining optimum selection of components and application of electrical power to coal mines. In order to make this tool useful, statistical material on equipment life must be gathered and all failures carefully recorded. Statistical data can be applied to new apparatus design and can be used to determine optimum configuration of network and maintenance to reduce costs. Reference is made to underground power systems in the USSR. Technical progress in the last few years has occurred in the design and application of highly productive coal mining and transporting machinery. One of the most important problems facing mining engineers is to increase the availability of the machine to obtain higher productivity. However, machine failures and breakdowns of electrical power supply components cause serious delays in the coal-winning processes. In spite of the fact that electrical equipment and the power supply contribute only a small percentage of direct mine costs, electrical failures as well as power supply delays can result in severe indirect losses. It is necessary, therefore, to consider reliability and safety in the application of electrical equipment underground. To obtain the best results, it is necessary to investigate and evaluate the reliability of the electrical mining components (starters, breakers, motors, cables, etc.) and optimal methods for minimizing maintenance, the desired result being equipment which is efficient and safe. Electrical equipment reliability directly influences economics: the lower the reliability the more frequently failures occur, causing serious working delays and possibly huge economic losses. By the same token, while increasing the number of preventive maintenance calls per unit time might result in fewer failures, thus reducing delays, the cost of making more frequent maintenance inspections will increase; this is one aspect to be discussed in detail. Obviously, failures of identical types of electrical equipment (starters with the same current and voltage, etc.) are influenced variably by different working conditions, environments, quality of the apparatus, maintenance procedures (personnel, frequency, quality), load, and other factors. Hence, the lifetime of identical types of equipment will vary depending upon usage in terms of the foregoing factors. Thus for a given type of electrical component, these factors must be considered quantitatively; the interaction of all these factors are evaluated quantitatively by a statistical method using probability theory. Equipment reliability must be quantitatively determined from a study of equipment life, since no one laboratory test can reproduce all working conditions and environmental effects. Nevertheless, reliability theory applied to electrical mining equipment is a very powerful mathematical tool for selecting as well as evaluating certain parameters. It is necessary to select several reliability parameters so that one can obtain an expression for the total overall economic situation in terms of cost, taking into consideration damage caused by electrical equipment failure and cost of maintenance. To accomplish this result, such characteristics as apparatus lifetime, breakdown idle time, and losses (damages) can be determined quantitatively on a statistical basis. For identical electrical equipment working under similar conditions, the previously mentioned reliability factors are random variables and therefore can be characterized readily by a probability density function. Investigations carried out by the authors in the Kuznetsk Basin (Kuzbas) in West Siberia, USSR, show that the reliability factors of electrical mining equipment are well described by the exponential, normal, or Erlang's distribution in most cases. Mining electrical equipment life is well-described by the exponential law. The distribution of lifetime density is

Jan 1, 1971

By C. H. Brehaut, W. N. Taylor, R. S. Douglas, H. A. Shannon

THE name for this new method of mining is derived from a composition of Horizontal, Radial, Diamond, and the drilling is from raises. This method, worked out at Copper Mountain, B.C., is believed to be distinct in many features from other known methods. GEOLOGY The ore deposits of Copper Mountain are related to the Copper Mountain stock, which is an ideal example of the magmatic differentiation in that it grades from a basic gabbro at the border to an almost pure orthoclase-pegmatite core. The "contact" ore bodies lie along the contact of the gabbro and an older complex of volcanics and sediment termed the "Wolfe Creek" formation. These older rocks, collectively referred to as greenstone, had been fractured prior to the intrusion of the stock and were highly metamorphosed during the intrusion. The "outlying" ore bodies are somewhat different in character, though a similar structural pattern prevails. It is believed that a deep-seated magma of which the Copper Mountain stock is a part has given off solutions that caused a partial granitization of some of the volcanics. Mining problems are caused further by the presence of a series of soft barren dikes intersecting a great many of the ore bodies, which are about 30 ft. wide, strike north-south, and dip at a high angle to the east; and are further increased by the presence of four major faults, with a great many minor faults running at acute angles from them. Fault zones average 8 ft. in width, and consist of gouge and breccia. They strike northeast and dip steeply to the northwest. The faults cut through the ore zones and the dikes, and continue on into the gabbro. The general mine structure with two types of ore bodies, bounded by weak walls and intersected by several series of soft barren dikes and major faults, indicated that a method of mining should be devised that would remove the ore at low cost with the least disturbance of the waste walls and dikes. THEORETICAL ESTIMATE OF STOPING WITH THE DIAMOND DRILL After consideration of various methods, the most suitable one appeared to be horizontal drilling to break the ore in a manner similar to shrinkage stoping. Drilling vertical holes or rings from a bench and breaking to an open slot was eliminated because the weak walls of ore, dike or waste would not permit this type of opening. It was then decided to drill either horizontal radial holes from a raise or parallel holes from a slot cut across the ore body. After discussion, the latter method was believed unsuitable, for the following reasons:

Jan 1, 1945

INCREASING realization that pouring and ingot-mold practices involve many factors of fundamental importance to ingot quality and general steel-mill operations has caused these phases of steelmaking to become major concerns of operators and metallurgists engaged in control of quality and costs. Methods of pouring steel from the ladle into the ingot molds have some direct effects on ingot quality. The mold itself governs solidification and dimensions of the ingot and in so doing exerts some very tangible influences not only on ingot quality but also on product yields and general steel-mill processing. In addition, practices are employed in the handling of molds during daily open-hearth operations that are important to quality and production costs. Therefore, pouring and mold practices must be considered highly specialized and important steps in steel-mill operations. MOLD DESIGN Mold design is difficult to discuss in a precise manner because it varies greatly throughout the industry, both in theoretical concepts and practical application, and few well developed data are available. Most ingot molds are designed to meet conditions peculiar to a given plant wherein quality standards are dictated by end-use requirements, which may differ considerably even for the same grade of steel. The mold designer must also consider the equipment available to process ingots and the product obtained from them. Such equipment, used for stripping, heating, blooming and finishing operations, is seldom, if ever, exactly the same in any two steel plants. Thus, pronounced contrasts in mold designs can be expected to continue, even among plants making strictly comparable types of product, particularly because some producers are just beginning to realize the benefits possible from specialized designs. Certain fundamentals are used in mold design but even these

Jan 1, 1964

DISCUSSION, A. Y. Bethune presiding M. E. Wadsworth and W. M. Fassell (University of Utah, Salt Lake City)—The authors of this paper should be complimented on the experimental techniques they have employed to investigate the rate of solution of galena in sodium hydroxide solution. Studies of this type are important not only as a practical means of leaching normally non-leachable substances, but also to determine the mechanism of solution at the solid-aqueous solution interface. There is some question, however, as to the conclusions which have been drawn by these authors concerning their proposed mechanism. Unfortunately, the contribution of OH- was not definitely established in their work, and concentrations less than 0.5 N NaOH evidently were not investigated. The pressure data at 123°C and 0.5 N NaOH were used to determine pressure dependency and the subsequent model proposed was taken as correct on the basis of the three points presented in Fig. 5 of the paper. In developing the

Jan 1, 1954

By Edward H. Robie

NEVER before have the annual company reports in the mineral industry field exhibited the typo-graphical art so abundantly as does the current crop. Time was when most company reports made a drab appearance and dry reading, mostly confined to financial data and text that gave little information to the public or technical men. Now, the dollar statistics assume less importance. Considerable information is given on what is going on at the company's plants, new equipment being installed, new methods, properties under development, ore reserves and grades, and similar information of interest to professional men working in the field. We have one suggestion for further improvement: The names of the officers and directors of the company are always given, but only a few companies give the names of the principal operating officials. We think, in the case of a mine for example, that the name of the general manager, his assistant, the mine and mill superintendents, and any other top operating officials who have been largely responsible for the success of operations, are worthy of mention. The reports are now widely read and this recognition is due them. Conspicuous among the annual reports that we happen to have seen, in point of typographical attractiveness, are that of the Texas Co., celebrating its fiftieth anniversary with a gold-plated cover and gold printing inside; and that of Noranda Mines Ltd., with a red and black cover that would attract attention anywhere. Comment on economics, taxes, and labor give an excellent picture of what our industry is facing. Consider the following, from the report of the Union Oil Co. of California:

Jan 1, 1952

By R. V. Horrigan

High purity ZrC14 (25 to 200 ppm of metallic impurities) can be readily prepared in simple apparatus by thermal decomposition of alkali chlorozirconate fused salts at 500° to 600°C and at atmospheric pressure. Suggested phase diagrams for the systems NaCI-ZrC14 and KCI-ZrCI, are presented. ALKALI chlorozirconate compositions — anhydrous fused mixtures of ZrCl4, NaC1, and KC1— are manufactured commercially and are used by the magnesium industry to introduce zirconium into magnesium alloys. Zirconium refines the grain size and improves the physical properties of many important magnesium alloys. In the course of working with chlorozirconate compositions of high ZrCl4 content, it was noticed that these salts decomposed progressively itwaswith increasing temperature to yield considerable amounts of a ZrCl4 sublimate of high purity together with a solid chlorozirconate residue. Further research led to: 1—improvements in the

Jan 1, 1956

By Daniel Hanson

FoR most of their practical applications metals are required to withstand stresses of appreciable magnitude: indeed, it id because they possess the quality of resisting stress without becoming permanently deformed that they find such extensive use in the service of man. Metals and alloys must, in service, usually behave as elastic substances—or nearly so. It is not difficult to satisfy this condition at ordinary temperatures. Iron and its alloys, especially the steels, are at normal temperatures excellent elastic bodies, capable of satisfying most of the mechanical requirements of the engineer: where electrical, chemical or other properties are impor-tant, which cannot be met by steels, it is usually possible to find a non-ferrous alloy such as nickel, copper or aluminum, which will prove satisfactory. When the metals or alloys are not inherently sufficiently elastic, cold-working or heat-treatment may develop elastic properties to a sufficient extent for practical needs. By means of relatively simple, rapid tests we can measure such properties as elastic modulus, limit of proportionality and proof stress, upon which design can be based with confidence. The case of the soft metals, such as lead and tin, is well known to be exceptional. They possess no definite limit of elasticity, and the value of proof stress or tensile strength depends to a great extent on the speed with which the test is carried out. Design here must be based on other considerations than a well-established theory of the proportionality of stress and strain. It is now generally recognized that steels and non-ferrous alloys possess at temperatures not greatly exceeding that of the atmosphere, characteristics quite different from those existing at ordinary temperatures, and that they assume qualities similar to those of the soft metals. Not only have they no limit of elasticity, but the proof stress and the ultimate stress depend on the time of application of the load. Flow under load may persist for long periods of time, possibly indefinitely, and the determination of a true maximum stress becomes a matter of great difficulty.

Jan 1, 1939

Jan 1, 1957

By Daniel Hanson

FoR most of their practical applications metals are required to withstand stresses of appreciable magnitude: indeed, it id because they possess the quality of resisting stress without becoming permanently deformed that they find such extensive use in the service of man. Metals and alloys must, in service, usually behave as elastic substances—or nearly so. It is not difficult to satisfy this condition at ordinary temperatures. Iron and its alloys, especially the steels, are at normal temperatures excellent elastic bodies, capable of satisfying most of the mechanical requirements of the engineer: where electrical, chemical or other properties are impor-tant, which cannot be met by steels, it is usually possible to find a non-ferrous alloy such as nickel, copper or aluminum, which will prove satisfactory. When the metals or alloys are not inherently sufficiently elastic, cold-working or heat-treatment may develop elastic properties to a sufficient extent for practical needs. By means of relatively simple, rapid tests we can measure such properties as elastic modulus, limit of proportionality and proof stress, upon which design can be based with confidence. The case of the soft metals, such as lead and tin, is well known to be exceptional. They possess no definite limit of elasticity, and the value of proof stress or tensile strength depends to a great extent on the speed with which the test is carried out. Design here must be based on other considerations than a well-established theory of the proportionality of stress and strain. It is now generally recognized that steels and non-ferrous alloys possess at temperatures not greatly exceeding that of the atmosphere, characteristics quite different from those existing at ordinary temperatures, and that they assume qualities similar to those of the soft metals. Not only have they no limit of elasticity, but the proof stress and the ultimate stress depend on the time of application of the load. Flow under load may persist for long periods of time, possibly indefinitely, and the determination of a true maximum stress becomes a matter of great difficulty.

Jan 1, 1939