Search Documents

By M. van Swaay, C. E. Birchenall

Palladium has a large capacity for the dissolution or occlusion of hydrogen; the gas also diffuses very rapidly through the metal. Palladium thimbles are widely used in the laboratory for purification of hydrogen by diffusion. The use of palladium filters could be extended to several large-scale applications if greater stability of the permeation process could be attained. In this paper a number of aspects contributing toward this goal are discussed, and new data on solubility and diffusivity are given. Palladium sheets of 0.005, 0.010, or 0.020 in. thickness were prepared by three procedures: casting and rolling, sintering palladium powder, and sintering palladium powder to which 0.1 pct thorium oxide had been added. Half-inch diam circular specimens were cut and clamped in a stainless steel holder provided with knife edges to seal the palladium sheet with soft copper gaskets. The seals were tested for leaks at l0-5 mm Hg. No difficulties from this source were encountered even after many temperature cycles in the system. The holder was silver-soldered to Kovar-glass seals and attached to the system through glass ball joints. Each joint was sealed with Apiezon wax and was adjacent to a cold trap. In several experiments the holders were fused directly into the system, eliminating the ball joints, to show that the wax did not affect the filter. Three filter holders were supported in holes in a stainless steel cylinder, which also acted as a temperature equalizing block inside the resistance wound furnace. The measuring thermocouple was inserted in one of the holders. A potentiometric controller with control thermocouple on the furnace heater winding maintained ± 0.2oC. Electrolytic hydrogen was purified and stored as shown in the flow diagram, Fig. 1. It could be admitted to either or both sides of the palladium specimens. Only a mechanical pump was used, for even high pumping speeds would not bring the pressure on the off-gas side of the filter below 10 to 50p Hg owing to the rapid hydrogen flow through the filters. A series of steady-state permeability studies allowed identification of several conditions of permeability loss. A constant fore pressure was maintained while the low-pressure face was pumped. After enough time had elapsed for a steady flow to be established the pump was cut off, and the rate of pressure increase in a thermostated bulb was measured to determine the flow rate. The time delay method of Daynes1,9 was adopted since it offered the possibility of determining solubilities and diffusivities. For each measurement both sides of the filter were evacuated for 15 min, which gave about 10-4mm Hg residual pressure. Hydrogen was admitted to one side or the other of the filter at a fixed pressure. The pressure on the off-gas side was observed as a function of time. A

Jan 1, 1961

By D. Webster

It has been found that cold work and annealing treatments greatly retard subsequent grain growth and re-crystallization in thoria-dispersed nickel and NiCr. It is suggested that this is due to cavities which form at the particle-matrix interface durilzg cold work. Some of' the cavities formed are stable at elevated temperatures and prevent the mouement of large-angle grain boundaries. The movement of these boundaries at elevated temperatures is known to start recrystal-lization and when they are pinned by voids recrystal-lization is made more difficult. TD Nichro,me had a maximun resistance to recrystallization when the initial structure was coarse-grained and had a low dislocation density. A precipitation reaction occurred between 700° and 1200° F in cold-worked TD Nichrome. It has been shown by Grant and his coworkers1-3 that a large part of the strength of dispersion-hardened materials is a result of the cold-worked structure produced during fabrication. In a comparison of the strength of cold-worked copper with and without an oxide dispersion, Grant4 has demonstrated that there is little difference in strength at room temperature. The function of the dispersion is essentially to maintain the cold-worked structure at higher temperatures than is possible in the base material. The dispersion accomplishes this by making recrystallization more difficult. The mechanism by which this is achieved is discussed in this paper. The fabrication history of the material has been found to greatly influence recrystallization behavior and this aspect is discussed in some detail. I) MATERIAL Three different thoria-dispersed materials were examined. 1) DuPont 2 pet thoria-dispersed nickel (TDNi) in 0.050-in. seeet. Thoria particle size is in the range 100 to 2500A. 2) DuPont 2 pct thoria-dispersed nichrome (20 pet Cr, 80 pct Ni) (TDNiC) in 0.125-, 0.060-, and 0.040-in. sheet. In the as-received condition these sheets have

Jan 1, 1969

By G. P. Boomslitter

In previous discussions on stresses in hoisting ropes, little has been said concerning the effect of the elasticity of the rope itself on the stresses due to acceleration. Laschinger1 has calculated acceleration stresses for several cases but he has ignored the elasticity of the rope as a factor, except as it compresses the drum and stretches itself as it winds thereon. He also deals with steam plants and he shows the effect of the "jerky" start of the engine. This effect would actually be reduced by the elasticity of the cable. With the advent of the motor-driven hoist, new conditions have arisen. The jerk mentioned by Laschinger has been eliminated and smoother starting made possible. But the elastic properties of the rope seem to introduce considerable periodic acceleration stresses in the rope. The following discussion of acceleration stresses is based on the assumption of a constant acceleration at the drum. To be exact, the mathematical work is based upon the assumption that the top is moving upward with a constant acceleration, and ignores the fact that the cable is shortening as it winds. However, the effect of the shortening would be inconsiderable during the first part of the acceleration period. Most hoisting engineers make the assumption of constant acceleration at the drum. Under the older method of calculating acceleration stresses, this would be true with a constant torque motor. But if stresses vary, as this paper attempts to show that they do, constant torque would not give constant acceleration, although the velocity-time curves obtained in the full size test herein described showed that they approach rather closely to this condition, at least as nearly as could be measured. Theoretical Discussion According to elementary physics, the force required to accelerate a Wf body of weight W at the rate of f ft. per sec.2 is wf . To raise the body Wf with acceleration of f ft. per see.2 the total force required is I + Wf, in if

Jan 1, 1927

AT the meeting of the Board of Directors held on June 25, 1926, and in response to numerous in-dividual suggestions for changes, a committee on Re-vision of the Constitution and By-Laws of the Insti-tute was appointed, consisting of C. F. Rand, Archi-bald Douglas and H. Foster Bain. Various confer-ences were held, much correspondence conducted and a preliminary draft was prepared. It proved imprac-ticable to complete the work in time to submit the matter to the membership for approval or disapproval at the annual meeting in 1927, and the Committee was continued with instructions to prepare a report as a basis of action in 1928. After Mr. Rand's death George Otis Smith was appointed in his place and the tentative draft herewith submitted has been pre-pared in its present form by Messrs. Smith, Douglas and Bain, though not differing in any material mat-ter from an earlier draft approved by Mr. Rand. In preparing this the Committee has kept in mind primarily the desirability of simplification and of making the By-Laws conform to the actual practice of the Institute as worked out through experience. The Constitution and By-Laws adopted in 1912, and which with minor amendments only still govern the Insti-tute, are full of specific provisions regarding pro-cedure; such as that laid down for guidance of the Papers and Publications Committee. Many of these have proved unworkable and in practice have not been always strictly followed. It now seems wise to write into the Constitution and By-Laws only the general fun-damental principles to he followed and to provide for such easy change in methods of following them out as will permit efficient conduct of the business. It is this thought that has guided the Committee in rewrit-ing many of the sections. With this in view also the Constitution, as such, has been shortened to the brief-est feasible statement of fundamentals. All matters relating to means of making these principles effec-tive have been put into the By-Laws or in the hands of committees whose work is subject to control and whose rules are subject to approval or disapproval by the Board of Directors. Many suggestions for changes have come to the Committee that have not been incorporated in this draft. Some of these are in themselves excellent but have not been incorporated here because the Commit-tee discovered no sentiment for them such as would be likely to secure their approval, or found them out of harmony with the general plan followed herein.

Jan 9, 1927

By J. H. Henderson, H. J. Ledbetter, N. B. Gove, J. D. Griffith

INTRODUCTION The results of a series of laboratory flood tests using liquid Iso-butane to displace refined oils from test cores are pre- ented and interpreted on an empirical bask. The study Revealed the similarity of the miscible liquid displacement to that of the immiscible-fluid displacement mechanism. The efficiency of the iso-butane flood decreased markedly as the oil Viscosity increased. but the effect of injection rate on the effectiveness of the primary production stage was negligible over the range investigated. The presence of free-gas saturation prior. to iso-butane breakthrough increased the volume of iso- Butane required to recover a given percentage of the oil present. Injection of liquid i.e.-butane prior to water follicle sculpted in a marked improvement in oil recovery by the water flood. INTRODUCTION The production of petroleum is often enhanced by the injec-1i1)n of extraneous fluids into the reservoir. It has been suggeited that the injection or cycling of a wet gas or a liquefied petroleum gas would he instrumental in increasing the effic.ienr!; of oil recover! to a greater degree than the commonly injected fluids. dry pas and water. Although instances of injection of light liquid hydrocarbons are not unknown, a systrmatic recording of the result is unavailable and superfi- cially, the practice gives the impression of being economicaIIy unsound. For specific types of displacement, analytic: solutions have been advanced which aid in understanding the physical mechanisms involved. However, there is no generalized theoretical concept which permits adequate prediction of displacement efficiency from a knowledge of readily measured reservoir rock and fluid properties. The Buckley-Leverett approach to oil displacement by an immiscible phase is an admirable analysiy of that type of mechanism. Dykstra and Parsons have introduced a useful concept in their evaluation of the role of the mobility ratio and its merit in rationalizing displacement phenomena. Everett, Gooch and Calhoun3 in their report on the effect of viscosity ratio and miscibility have pointed out the lack of a comprehensive theoretical approach and the desirability of investigating the mechanism of miscible-miscible displacement. In lieu of a well-developed theory concerning miscible-111isci1)le displacement and in view of the scarcity of engineering information on actual LPG injection trials, the limited program of laboratory experimentation described below was undertaken. OBJECTIVES The original broad objectives of the program, to study the oil recovery process using LPG as the displacing phase, defined the direction and scope of the laboratory tests. The specific objective. of the experimentation were to evaluate

Jan 1, 1953

By Ian Wark

IT has been shown1 that in the absence of heavy metal salts, the nature of the alkali used to promote differential flotation-whether caustic soda, lime or sodium carbonate-is unimportant. The hydroxyl ion is the active depressant upon which differentiation depends, and the pH value determines whether a film of collector forms on any given mineral surface. Even when sodium cyanide is used in conjunction with alkalies, it is the pH value and not the nature of the alkali or its concentration that is important, for upon the pH value alone depends the fraction of the added sodium cyanide that is present as cyanide ion, which is the true depressant. When heavy metal salts become dissolved from partly oxidized ores, or are added intentionally as activators, conditions are different, and metallurgists have found that lime and sodium carbonate do not give identical results, even when added in amounts sufficient to produce the same pH value. In the few instances in which we had attempted to confirm this view, we had failed to do so, for, with nothing to guide us, we had inadvertently chosen solutions that gave contact curves of a "stand-ard type," which correspond to conditions of ready floatability. Now, however, we find that, in the presence of copper salts, and within a restricted range of reagent concentrations, the nature of the anions present is important, and that sodium carbonate does influence the results, apart from the usual effect due to its influence on pH value. With the recognition of this anion effect, and with the control of temperature already introduced,' it appears that the factors of major importance in connection with this set of reagents have been taken into consideration, and that the results obtained and the conclusions drawn from contact tests will be of more immediate value to the operator.

Jan 1, 1939

By Kjell Lidin, Christer Nordström

INTRODUCTION LKAB produces iron ore in several mines in northern Sweden, and has been doing so for nearly 100 years. Total production to date is 600 million tonnes of finished products of various kinds (pellets, lump ore, fines). Close to 400 million tonnes have been produced by sublevel caving. This method has been the company's standard method for more than 20 years. A review of the development of equipment over the past 15 years and an outlook up to about 1990 leads to the following general re- flections concerning probable trends. Trends for all equipment are increasing precision and stricter environmental requirements will necessitate cabs, remote control etc to an increasing extent. Conventional sublevel caving can be broken down into the following unit operations: 1. Planning incl prospecting drilling. 2. Horizontal drilling. 3. Fan drilling. 4. Charging and blasting. 5. Loading and haulage at sublevels. 6. Ore drawing in chutes. 7. Rock reinforcement. 8. Production service. This lecture will deal in brief with each of these unit operations and the trends we are experiencing for them. A number of slides illustrating equipment

Jan 1, 1981

By C. G. Rhodes, D. Kramer

High-field critical transport current density (J) measurements at 4.2 °K as a Junction of applied magnetic field (H) were made on samples of cold-rolled and annealed columbium with H parallel to J. Microscopic examination of the samples revealed a well-defined planar fiber structure produced by the cold rolling. J was found to he lower when fibers are parallel to the direction of magnetic field penetration than when they are perpendicular. This effect may he a consequence of the interaction of flux movement with fiber boundaries. THE severe changes in microstructure brought about by cold working superconductors leads to profound changes in their superconducting behavior. In particular, the ability of a superconductor to carry a transport current with zero resistance (the maximum value of this current density will be called "J" in the presence of large external magnetic fields (to be referred to as "H") is greatly influenced by the microstructure. In the case of columbium, LeBlanc and Little1 and Autler et a1.2 have observed an increase in J due to cold work. LeBlanc and Little also observed an anisotropy in J in cold-rolled columbium strips, which Hake et al.3-6 have shown to depend upon the angle between H (H ? J) and the rolling plane. An increase in J due to cold work has been found in a variety of high-field superconducting alloys3'4'7-9 as has the anisotropy effect.10 First explanations of why cold work raised J invoked the idea that dislocations carried the high-field supercurrents,8,11 since cold working drastically increases the dislocation density and presumably the number of supercurrent paths. However, recent ideas on the nature of high-field superconductivity together with new experimental evidence reveal that the bulk of certain superconductors can remain superconducting in high fields while carrying high transport currents. These later developments have been discussed by Berlin-court and Hake12 and a comprehensive review has been prepared by Berlincourt.13 According to the ideas of Gorter14 and Anderson,15 one would expect that the influence of microstructure on high-field supercurrent density will depend on tine interaction between microstructure and penetrating flux and on the direction of the Lorentz

Jan 1, 1965

The finding of gold, in enriching quantity, along the streams that issued from the western foothills of the Sierra Nevada was the prelude not only to the birth of an organized mining industry in California but to the intensive exploration of the entire Pacific slope; it presaged the feverish exploitation of the mineral resources that the ubiquitous prospector soon uncovered all over our western domain. At first when this migration began, as typified by the rush of 1849, there was no time to examine the signs of ore that were to be detected along the track of adventure, and, it must be added, not many in that motley crowd of gold-seekers were qualified to interpret the signs if they had lingered to look at them. Such intelligent curiosity as a few of them possessed was directed to the finding of gold chiefly, if not exclusively; and their good sense in this respect can not be impugned, because in a new and remote country the less valuable metals and minerals are unlikely to be worth the winning. Many of those that came to California crossed the alkaline wastes and sagebrush prairies that extend between the Great Sal? Lake and the ramparts of the snow-clad Sierra; when coming overland they found it convenient to halt on the eastern slope and to pitch their camp in the valley of the Car- son river before they began the tedious ascent of the mountains and the final entry into the land of gold. One of the trails most used by these immigrants followed the Carson river to the mountain meadows south of Lake Tahoe and then descended among the pine-woods of Placerville, where they went to work with pan and shovel in the gold-bearing streams

Jan 1, 1932

By E. G. Leonardon, D. C. McCann

The search for oil has required, and without a doubt supplies, a tremendous amount of information on the structure, composition, physical properties, and history of sedimentary rocks. The earliest and most complete source of knowledge is the sample or core of the rock itself, the uses of which are well known. The purpose of this paper is primarily to discuss a new method for obtaining these cores, and to illustrate its use in connection with electrical logs. Most cores have been obtained through a special adaptation of rotary drilling, and the results have been remarkably good, considering the mechanical problems involved. Unfortunately, because of the time and expense, this method cannot be used for the entire length of the drill hole. Even though ingenious contrivances have been evolved in order to reduce the time spent in round trips, such as wire-line coring equipment, mechanical coring still remains too expensive to be carried out continuously. In practice, therefore, one is finally compelled to estimate the probable depths of the more interesting horizons and, allowing a wide margin of safety, to core through those sections only. It is true also that interesting results have been obtained by examining the cuttings brought to the surface by the mud circulated in the well during the process of drilling. Be that as it may, the inescapable fact remains that key horizons may be passed inadvertently, for one reason or another, while the drilling operations are being performed. The only continuous record of the formations encountered is that furnished by electrical surveys. Obviously, it would be desirable to make the electrical survey first and to take the samples from the wall of the hole according to the indications on the electrical log. In this way, it would be possible to core only the exact sections desired, eliminating the otherwise inevitable estimates as to the point at which to start coring, and thereby reducing to a minimum this expensive operation. At the same time this method would provide a maximum of useful samples. A device for taking samples of the formation from the walls of a hole therefore offers the possibility of recovering cores from zones otherwise lost as a source of this type of information. Furthermore, by coring

Jan 1, 1939

By Russell W. Dayton

The metallurgical polarization microscope has been utilized in several researches in the last few years, thus attaining a fair degree of prominence, but little has been written in a manner suitable to a metallurgist concerning the theory of this instrument. In this investigation the theory was carefully studied, and the results are presented here in a detailed manner, yet as simply as possible. The theory is discussed with particular reference to the three chief functions of the instrument: (1) determination of anisotropy; (2) effect of strain; and (3) identification of inclusions. Each of these is investigated experimentally, with especial attention to the mechanism of producing any effect. Where possible, the discussion is supplemented by photomicrographs. The instrument used had numerous defects as a polarization microscope; these and their remedies are discussed. In the microscopic study of transparent mineral sections (chalcography) the use of polarized light has aided tremendously in the identification of a mineral. The determination of strain in transparent substances (photoelasticity) by the use of polarized light has lately become a commercial process, used in testing finished glass articles. The success of the use of polarized light with opaque materials has not been so great. The magnitude of the effects obtained is much less than that of the corresponding effects with transparent materials, and the mechanical difficulties are much greater. Königsberger,"' i in 1909, was the first to apply polarized light to the microscopic study of opaque substances; Endell and Hanemann(2) were the next, in 1913. In 1919 and 1920, Wright(3,4) prepared two papers on the subject. In the first he developed the detailed mathematical theory from the viewpoint of the electromagnetic theory of light, and in the second described the various methods in use, giving improvements of his own. Schwarz(5)

Jan 1, 1935

By Charles S. Barrett

This paper is a progress report covering metallographic applications of the electron microscope that have been made during the past year at Carnegie Institute of Technology. An account is presented of the techniques that have been most satisfactory, the difficulties encountered, the resolution obtained, and the peculiarities that have been noted in the microstruc-tures. About 1200 exposures have been made during the year on the instrument, which is an RCA type B2 transmission microscope,' and a number of these have been selected to illustrate the results obtained. prints are also included showing the common types of falsities—to borrow a term from the biological field, the "artifacts." ln brief, the paper is a record of our attempt to determine the value of the electron microscope in the study of the structure of metals and alloys. In addition to comments on techniques and the quality of photomicrographs obtainable with them, the paper discusses the nature of the etch attack on a few metals, and the possible relation between the fine structure revealed by etching and the mosaic block structure of the grains, since numerous papers and reviews are available on the subject of imperfection in crystals, the comments here may be very brief; in fact, are restricted almost entirely to points having to do with recent theories relating the strength of metals to imperfections and to spacings of slip lines. Specimen Preparation and Photographs Mechanical polishing by hand was used throughout this work. Precautions that must be taken in microscopy at high magnification, which have been well explained by Vilella in his book on Metallographic Technique for Steel, are likewise important with the electron microscope. This applies particularly to the need for these polishing and etching (each successive polish becoming less severe and each etch lighter), since the fina1 etch should in general be no heavier than is used for oil-immersion optical microscopy and in many instances should be much lighter (compare Figs. 6a and 7a, 6d and 7b). An extremely light etch, of course, is incapable of cutting through a flowed layer of appreciable thickness. Unquestionably it would be very advantageous in each instance to compare the structures obtained by electrolytic polishing with those obtained by mechanical polishing, but difficulties with the electrolytic method have prevented this in the following collection of prints. The choice of etchant is important, of course; for example, picral proved superior to nital for tempered martensite. With the exception of Figs. Ib and 16, the replicas used were of silica, deposited upon polystyrene and floated from the polystyrene in ethyl bromide according to the method of Heidenreich and Peck.2 The samples were mounted in Bakelite, polished and etched, then the polished Bakelite

Jan 1, 1944

By W. A. Hutchins

Water laws important to the mining industry are those which govern or affect the right to use water, to dispose of water after using it in mining or milling, and to discharge waste material into watercourses. They include statutes and court decisions having general applicability, as well as others that pertain specifically to mining. THE INDUSTRY'S CONTRIBUTION TO WESTERN WATER LAW Despite sharp differences of opinion, the water law the Spaniards brought to the Southwest appears to have included some form of appropriation of water. The Mormons, who settled in Utah in the mid-nineteenth century, also developed a system of appro-priative water titles. But by far the most profound impact on western water law was made by the gold-seekers who flocked to the Sierra Nevada foothills of California after the discovery of gold in 1848. Much of the gold was extracted from the ground by hydraulic or placer mining, and so the miners' rights to the use of water became fundamentally important. Since there was no organized government in the foothills and no laws other than those made by the miners, they helped themselves to the land, the gold, and the water needed to work their claims.1 They established and enforced regulations governing the acquirement and holding of mining claims and their rights to the water they needed.' In 1879 Justice Field, former Chief Justice of the California Supreme Court, spoke for the U. S. Supreme Court in saying that the miners were "emphatically the law-makers, as respects mining, upon the public lands in the State."" Rules of the California mining camps were based on two essential principles: 1) priority in discovering claims and appropriating water by diverting it from streams and putting it to use, and 2) diligence in working claims and applying water in mining. The customs so developed, which were copied in mining areas of other states and territories, were enacted into law in one western jurisdiction after another. They form the basis of what is called the arid-region doctrine of prior appropriation of water, which received the attention of Congress in legislation recognizing and protecting appropriations of water for mining, agriculture, and other purposes on the public domain.' In several western states a great number of water cases decided in the early years involved relative rights to the use of water for mining purposes or for milling connected with mining." The miner's inch, the customary unit for measuring water in the mining camps, is still used in various western communities, although its relation to the cubic foot per second varies from one area to another. Undoubtedly, the miners of a century ago made the major contribution to the appropriation doctrine as it is now recognized and applied throughout the West. What inspired the California gold-seekers to develop these principles? Thoughtful writers have pointed out that their regulations and customs were strikingly characteristic of much earlier mining enterprises in the Old World.D It is said that the right of free mining and free use of flowing water therefor —so similar to the California conditions and practices—-was a part of the customs of Germanic miners in the Middle Ages, that it spread from middle Europe to other countries and colonies, and that the doctrine of prior appropriation was widespread in the important mining regions of the world. Certainly the Forty-niners came to California from many countries. It does not tax the imagination to consider that they may have brought with them some knowledge of the old Germanic customs and applied this knowledge in their new environment. RIGHTS TO USE OF WATER IN GENERAL In the West, rights to the use of water of watercourses fall into two categories—appropriative and riparian. The doctrine of prior appropriation is recognized in each of the 17 western states. The riparian doctrine is recognized concurrently with the appropriation doctrine in some of these states but has been abrogated in the others. The riparian doctrine prevails generally throughout the East, although there is now considerable interest in developing something else. Generally speaking, the appropriation doctrine has been highly developed in the West, whereas the principles of riparian doctrine have been comprehensively established in only a few states throughout the country. The subject of water rights is a big one. Space permits no more than a brief discussion of aspects that bear upon the title of this article. RIGHTS OF PRIOR APPROPRIATION Fundamental to the doctrine of prior appropriation is the principle first in time, first in right. Although in some states there are statutory exceptions. the original and still generally prevailing rule is that the first one who initiates a right to divert and use water of a stream, and who completes his undertaking with reasonable diligence, acquires thereby the first right of appropriation of the specific quantity of water involved. Each succeeding right in point of time is junior to all earlier rights but senior to all later ones. The practical effect of this priority system is that when the water supply is not enough for all, the earliest rights must be fully satisfied before any water may be taken by those later in time. Acquirement of Appropriative Rights: Each of the 17 western states has a statute under which water may be appropriated pursuant to a prescribed procedure. Generally, the first step to be taken by the intending appropriator is to file application in the office of the State Engineer for a permit to make the appropriation. In most but not a11 states, valid ap-

Jan 1, 1961

By Charles S. Barrett

This paper is a progress report covering metallographic applications of the electron microscope that have been made during the past year at Carnegie Institute of Technology. An account is presented of the techniques that have been most satisfactory, the difficulties encountered, the resolution obtained, and the peculiarities that have been noted in the microstruc-tures. About 1200 exposures have been made during the year on the instrument, which is an RCA type B2 transmission microscope,' and a number of these have been selected to illustrate the results obtained. prints are also included showing the common types of falsities—to borrow a term from the biological field, the "artifacts." ln brief, the paper is a record of our attempt to determine the value of the electron microscope in the study of the structure of metals and alloys. In addition to comments on techniques and the quality of photomicrographs obtainable with them, the paper discusses the nature of the etch attack on a few metals, and the possible relation between the fine structure revealed by etching and the mosaic block structure of the grains, since numerous papers and reviews are available on the subject of imperfection in crystals, the comments here may be very brief; in fact, are restricted almost entirely to points having to do with recent theories relating the strength of metals to imperfections and to spacings of slip lines. Specimen Preparation and Photographs Mechanical polishing by hand was used throughout this work. Precautions that must be taken in microscopy at high magnification, which have been well explained by Vilella in his book on Metallographic Technique for Steel, are likewise important with the electron microscope. This applies particularly to the need for these polishing and etching (each successive polish becoming less severe and each etch lighter), since the fina1 etch should in general be no heavier than is used for oil-immersion optical microscopy and in many instances should be much lighter (compare Figs. 6a and 7a, 6d and 7b). An extremely light etch, of course, is incapable of cutting through a flowed layer of appreciable thickness. Unquestionably it would be very advantageous in each instance to compare the structures obtained by electrolytic polishing with those obtained by mechanical polishing, but difficulties with the electrolytic method have prevented this in the following collection of prints. The choice of etchant is important, of course; for example, picral proved superior to nital for tempered martensite. With the exception of Figs. Ib and 16, the replicas used were of silica, deposited upon polystyrene and floated from the polystyrene in ethyl bromide according to the method of Heidenreich and Peck.2 The samples were mounted in Bakelite, polished and etched, then the polished Bakelite

Jan 1, 1944

By Russell W. Dayton

The metallurgical polarization microscope has been utilized in several researches in the last few years, thus attaining a fair degree of prominence, but little has been written in a manner suitable to a metallurgist concerning the theory of this instrument. In this investigation the theory was carefully studied, and the results are presented here in a detailed manner, yet as simply as possible. The theory is discussed with particular reference to the three chief functions of the instrument: (1) determination of anisotropy; (2) effect of strain; and (3) identification of inclusions. Each of these is investigated experimentally, with especial attention to the mechanism of producing any effect. Where possible, the discussion is supplemented by photomicrographs. The instrument used had numerous defects as a polarization microscope; these and their remedies are discussed. In the microscopic study of transparent mineral sections (chalcography) the use of polarized light has aided tremendously in the identification of a mineral. The determination of strain in transparent substances (photoelasticity) by the use of polarized light has lately become a commercial process, used in testing finished glass articles. The success of the use of polarized light with opaque materials has not been so great. The magnitude of the effects obtained is much less than that of the corresponding effects with transparent materials, and the mechanical difficulties are much greater. Königsberger,"' i in 1909, was the first to apply polarized light to the microscopic study of opaque substances; Endell and Hanemann(2) were the next, in 1913. In 1919 and 1920, Wright(3,4) prepared two papers on the subject. In the first he developed the detailed mathematical theory from the viewpoint of the electromagnetic theory of light, and in the second described the various methods in use, giving improvements of his own. Schwarz(5)

Jan 1, 1935

By F. H. Wilson, R. M. Brick

With the papers of Palmer and Smith1 and of Burghoff and Bohlen,2 published in 1942, understanding of the problem of the development of ears on deep-drawn brass cups was brought to the point where, from a practical standpoint, producers of brass sheet could keep earing under control. However, these very practical results raised questions concerning the reasons for the observed behavior. Since plastic deformation is fundamentally a function of crystallographic slip, these reasons must be considered in the light of the textures to be found in the annealed sheet. Various attempts have been made. to interpret the mechanism of ear formation by correlation with the preferred orientation and the anisotropy of the sheet. However, none of these has satisfactorily explained why ears are usually found in the rolling and transverse directions for copper but at 45' to these directions for brass. This paper offers additional data on these two related subjects and has been divided into two sections The first section provides a survey of the recrystallization textures of brass as affected by annealing temperatures and prior reductions, and an account of the caring behavior which accompanies these textures. The second section reports new data on the anisotropy that accompanies a characteristic texture for brass and endeavors with partial success to establish the factors that account for the difference in earing behavior between copper and brass Earing BehavioR oF Brass Review of Textures The recrystallization texture of severely rolled brass was first reported by Bass and Glocker.3 The preferred orientation to which this texture, obtained from metal annealed at 500°C., was most akin was (II3)[I12] This texture has been confirmed by Bauer, von Göler and Sachs;4 Brick;' Brick, Martin and Angier;6 and Cook and Richards7 who, in general, used annealing temperatures under 500°C. Bass and Glocker3 also reported the recrystallization texture at 850°C. to be the same as at 500°C. They analyzed their textures by means of single photograms obtained with white radiation. The photo-grams for both temperatures are reproduced in their paper, and there is a strong similarity between the two. However, for the latter temperature, the number of spots registered on the film was remarkably large for the grain size to be expected, and the authors made no mention of using a technique that would integrate a large enough area of the specimen to produce so many spots. The only other attempt to determine textures resulting from high temperature

Jan 1, 1945

By William Kelly, F. H. Armstrong

The object of this paper is to describe the electric equipment at the iron-ore mines of Penn Iron Mining Co., Vulcan, Mich. and of Republic Iron Co., Republic, Mich.; to give the results of tests; and to discuss the methods in use from an operating as well as from an efficiency standpoint. Electricity was introduced at the Penn mines for pumping, hoisting, and compressing air in the spring of 1907, upon the completion of a hydro-electric plant built by that company on the Menominee river about 4 miles from the mines. This plant was described in a paper1 presented before the Lake Superior Mining Institute. A paper2 presented at a meeting of the same Institute describes some of the operating features, and the safety devices of the electric hoist at the Curry shaft were briefly described in the Proceedings of the First Co-operative Safety Congress held under the auspices of the Association of Iron and Steel Electrical Engineers at Milwaukee, Wis., Sept. 30 to Oct. 5, 1912. Generating PoweR Plants After the success of electrical operation was assured, a second set of water wheels and generator was installed at the falls, for which provision had been made in the original design and in the construction of the foundations, and later three additional wires were added to the main transmission line, doubling its capacity and reducing the line loss. The general conditions of this installation are particularly favorable for hydro-electric operation. In the neighborhood of three-fourths of the power used is for mine pumping, which in the main is regular and continuous. For air compressing, power is used for about 18 hr. a day for five days, and 9 hr. for one day in the week, though occasionally when shaft sinking is going on a very small amount of compressed air may be

Jan 1, 1915

By Allan T. Gwathmey, J. Bruce Wagner, Kenneth R. Lawless

Between 250°and 550°C in oxygen pressures of 10 to 760 mm Hg, the relative oxide thicknesses formed per unit time on the (100), (111), (110), and (320), decreased in this order. The predominant oxide orientation was (001)Fe3O4 and [110] Fe304 A small amount of a-Fe2O3 which exhibited a fiber pattern was observed in all oxides except those formed at 250°c in low oxygen pressures. IN order to understand the properties and behavior of thin films, particularly their role in oxidation reactions, there is needed more experimental information on their structure, composition, and kinetics of formation on clean surfaces of known geometry. The present study was undertaken to obtain such information for thin oxide films formed on single crystals of a body centered cubic metal, iron. Crystals in the form of spheres were used in order to expose all possible crystal planes to the reactant gases simultaneously. Using this procedure the relative rates of oxidation of all planes could be estimated, and those exhibiting, maximum or minimum oxidation rates could be selected for a more intensive study of composition and expitaxy. Since the three types of information were obtained from the same experiment using a single crystal substrate, any differences between rate, composition, and expitaxy on the several planes may be attributed to the influence of the substrate structure. EXPERIMENTAL The starting material for this study was Armco iron rods, 6 in. long and 3/8 or 1/2 in. in diam. The analysis was reported to be 99.8 pct Fe, with major impurities listed as carbon 0.018 pct, manganese 0.027 pct, phosphorous 0.005 pct, sulfur 0.029 pct, silicon 0.005 pct, and copper 0.11 pct. These rods were cleaned with ether and heated in an atmosphere of moist hydrogen at 950°C for three days. The purpose of this treatment was to decarburize the iron and to provide a consistent, uniform grain size for the growth of single crystals. Crystals in the form of rods, up to 1/2 in. in diam and 2 in. long, were prepared by a method similar to that reported by Leidheiser and Buck.2 Spherical crystals, 3/8 and 1/2 in. in diam and having a handle about 1/4 in. in diam by 112 in. long, were machined from the single-crystal rods. After machining, each crystal was etched in aqueous nitric acid to remove the cold-worked metal at the surface. Before each experiment, the crystal was polished mechanically with metallographic papers through number 4/0, and electropolished in a perchloric acid-acetic anhydride mixture by the method of Jacquet and Rocquet.3 The crystal was washed in running distilled water for at least 5 min. The excess water was blotted with a soft paper tissue, and the crystal was placed in an all-glass reaction vessel (See Fig. 1). The crystal was heated at 550°C in hydrogen for at least 8 hr prior to the oxidation in order to reduce any surface oxides and to help relieve any stresses in the metal. For the structure and composition studies, flat faces were cut parallel to (loo), (111), and (110) planes on the iron crystal spheres. The orientation of these faces was checked by a back-reflection X-ray diffraction technique. The faces were within 2 deg of the desired orientation. The flat faces were treated as described above except that prior to electropolishing they were given an additional polish on metallographic felt saturated with twenty-minute levigated alumina. After the crystal was heated in hydrogen for at least 8 hr, the temperature was adjusted to the desired value, and the hydrogen was evacuated. Commercial oxygen which had been purified by successively passing through tubes containing magnesium perchlorate, Ascarite and magnesium perchlorate was admitted to the desired pressure as measured by a mercury manometer. A resistance-wound furnace surrounded the oxidation chamber, and a temperature controller maintained the temperature within ±3°C. The furnace was provided with a small window for observing the crystal. The changes in thickness of the oxide films were followed by observing the interference colors. The oxidation was allowed to proceed until the desired oxide thickness was attained on a given crystal plane. The experiment was terminated by evacuating the oxidation

Jan 1, 1962

By J. D. Price, G. V. Woody

MANY producers of by-product coke have spent considerable time and given considerable thought to the use of a substitute for low-volatile coal as an admixture with high-volatile coking coal for charging high-temperature by-product coke ovens. Generally speaking, there are two principal reasons for this, one being occasioned by the lack, in certain localities, of low-volatile coal delivered at a cost sufficiently low to permit its use, and another being the desirability of finding a substitute product with a delivered cost lower than the cost of the low-volatile coal. It was for the first of these reasons that the Colorado Fuel and Iron Corporation was particularly interested in this subject. This paper deals with the experimental work and the results obtained by that company in producing and using low-temperature char. OVERCOMING DEFECTS IN COKE FROM COLORADO COALS Colorado coking coals are all of the high-volatile type and were all laid down during he Cretaceous period, which makes them something like 80 million or so years younger, geologically, than eastern coals. They behave, when coked alone, something like the Pittsburgh-seam coals. They make a very brittle, highly cross-fractured, fingery coke of fair shatter value but quite low in resistance to abrasion. Mixed with a low-volatile coking coal such as Pocahontas or certain Oklahoma coals, they make a coke that is equal to virtually any of the eastern cokes. The inferior quality of Colorado coke has long been recognized, and a considerable amount of time, effort and money has been spent upon investigations of means for improving its physical properties. While it has been found that some improvement in quality of coke can be secured by the adjustment and control of such variables as pulverization, moisture content, oven temperature and bulk density of charge, and through the addition of certain inert materials such as pulverized coke breeze, pitch, high-volatile noncoking or semicoking coal, the benefits so gained have been comparatively small. There are no low or medium-volatile coking coals available within a reasonable freight-cost distance. Therefore a substitute for low-volatile coal was developed through low-temperature carbonization-or, more correctly speaking, through the partial devolatilization-of high-volatile coals. The blending of this lower volatile char with the high-volatile coking coal distinctly improves the quality of coke made from Colorado coal. There is nothing especially new about this idea. In 1908 a Japanese patent was taken out by Kotaro Shimomura, whose claim was: The method of making a nonfingery coke out of bituminous coals, without using natural coals of low-volatile matter; according to which a certain coal is heated at a temperature between about 300°C. and about 600°C. so as to leave about 15 to 25 per cent volatile matter in the coal; this coal is mixed with the

Jan 1, 1944

INTO their great Pacific Northwest counting house went the members of the Industrial Minerals Division recently, to count their blessings amidst the scenic grandeur and mineral wealth of the State of Washington. From their vantage point in Seattle, those who attended the IMD's fourth Pacific Northwest meeting turned their sights to the South and Southeast, scanned Montana, Idaho, Oregon and Utah, and predicted a very healthy economic future for their region. The praises of Idaho's booming phosphate industry were sung by Earl W. Murphy, secretary of that State's Chamber of Commerce. He said the establishment of Fort Hall, on the banks of the Snake River near Pocatello, first turned the eyes of the world toward what is now the center of the greatest known deposits of phosphate rock-the section adjacent to the common corners of Idaho, Wyoming and Utah. With the founding of Fort Hall, Mr. Murphy said, historians will also rank the construction of the first electric furnaces for the production of elemental phosphorous as equally significant in the commercial history of the West. Those furnaces were installed only last year by the Westvaco Chemical Div. of the Food Machinery & Chemical Corp. at Pocatello, at a cost of $8 million.

Jan 7, 1950