Search Documents

By Barbara A. Thompson

A previously reported high-resolution method for the location of boron-rich areas in metallurgical and biological specimens was been adapted for general use on a routine basis. The rnetlzod utilizes neutron activation and autoradiograpizy. Alpha-particles emitted by boron nuclei upon neutron capture are recorded on a photographic emulsion. The resulting a-particle tracks show the location of boron-rich areas. Experimental techniques, interferences, and limitations of the method are discussed in detail. The method is most useful where there is marked segregation of boron. In this type of sample, the segregation can be observed when the nominal boron concentration is as low as 0.0006 pct. THE positive identification and location of boron-rich areas in metals is frequently of great interest in metallurgical work. Unequivocal identification is often difficult to make by conventional metallo-graphic methods. Recently, a method has been described which accomplishes this objective by neutron activation and autoradiography.l-3 The method can be described briefly as follows. Upon neutron capture, a -particles are emitted by boron nuclei according to the following reaction: ,Blo + n - ,a4 + 3Li7 + 2.4 mev The energy is dissipated as kinetic energy of the products. By irradiating a boron-containing sample in contact with a photographic emulsion and subsequently developing this emulsion, a-particle tracks are obtained whose location corresponds to the location of boron-rich areas in the sample. Two factors combine to make the reaction extremely specific for boron. The first is the unusually high (755 barns) cross section of boron for thermal neutron capture. The second is the higher neutron energy required to produce (n, a ) reactions in essentially all other nuclei except lithium. These two factors make the method specific for boron by six to seven orders of magnitude when a predominantly thermal neutron source such as the Brookhaven reactor is used. The reported limit of detection of this method is of the order of 0.01 pct B., The present work was originally undertaken to determine whether this limit could be lowered by use of a thinner emulsion. However, initial experiments showed that in order to use the method at all, it was necessary to reestablish the optimum experimental conditions in terms of the available irradiation facilities. It is the purpose of this paper to describe these experimental conditions in detail, to discuss the factors influencing sensitivity, and to evaluate several techniques for increasing sensitivity. EXPERIMENTAL A) Preliminary Experiments—The first measure-ments were made using samples of crystal oriented silicon steel containing various concentrations of boron. In the later experiments, samples of various high-temperature alloys such as M-252, hcoloy 901, Nichrome V, and so forth, were used. Faraggi, et al.,2 reported that the lower limit of sensitivity in this type of sample was about 0.01 pct B using nuclear emulsions of 50- u thickness. but that it should be possible to extend this limit by the use of thinner emulsions. Accordingly, we first used Kodak Auto-radiographic Stripping Film (Permeable Base) which has an emulsion thickness of only 5 µ. This was mounted on the metallographic specimens according to the technique described by Boyd.4 The emulsion remained in contact with the metal surface throughout exposure and development. Since the emulsion is transparent after development, the autoradiograph and metal surface can be viewed simultaneously and any correlation between film blackening and structure of the metal can be made directly with no problems of realignment. Because the silicon steel is readily attacked by moisture alone, it was necessary to apply a protective coating to the metal surfaces before mounting the emulsion. The coating was made extremely thin in order to absorb as few a-particles as possible. Boyd4 and Gomberg5 have discussed various plastics used for this purpose; however, none was sufficiently impermeable to prevent chemical attack of the steel during the developing process. This attack resulted in the production of gross chemical artifacts in the emulsion. It was, therefore, necessary to use the method of Wolfsberg and John6 as follows. A very thin (approximately 1 µ) coating of Plexiglas II was applied by dipping the sample in a 2 pct solution of Plexiglas II in dichloroethylene. Then, because the emulsion will not adhere to Plexiglas 11, a thin coating of Parlodion was applied in a similar manner using 2 pct Parlodion in iso-amyl acetate. No protective coating was necessary with the high-tem-

Jan 1, 1961

By Norman B. Pilling, George P. Halliwell

The effects of lead and tin up to maximum contents of about 0.1 per cent. each, in the presence of oxygen between 0.04 and 0.30 per cent., have been studied. Tin is retained efficiently in the oxidized condition, whereas lead is not. An approximate relation between the lead-oxygen and tin-oxygen contents is deduced which, if observed, permits the presence of these elements without detrimental effect. Excess of lead beyond this limit affects ductility and rolling properties adversely and an excess of tin correspondingly diminishes the conductivity. It is shown that copper carrying a combined lead and tin content of several hundredths per cent., yet fully equal in quality to electrolytic wirebar, may be produced under commercial conditions. Tin is not normally found in more than bare traces in current grades of American electrolytic copper, and lead is rarely found to more than a few thousandths per cent. In the electrolytic refining of copper these metals do not present great difficulty in separation and their presence in any considerable amount in copper that has been refined by this method need not be tolerated. On the other hand, the effect of these elements is not entirely academic, as a considerable tonnage of scrap copper liberally contaminated with them has been reclaimed by the fire-refining process into metal with a residual lead and tin content of several hundredths per cent., yet having excellent working properties and fully equal in quality to current grades of electrolytic wirebar. Such copper has been found entirely suitable for use in the manufacture of electrical apparatus. In the absence of oxygen, tin is known to depress the conductivity rapidly, and lead to impair ductility and the rolling properties, yet the effects of these metals on commercial grades of copper—i. e., copper containing from 0.03 to 0.10 per cent. of oxygen—apparently has not received systematic attention. Occasional reference is made to the fact that in the presence of oxygen lead may be tolerated, yet Addicks says,1 in regard to overpoling: "The unstable condition can be controlled by adding certain substances, notably lead, in small quantities, but as mere

Jan 1, 1926

By G. W. Healy, W. D. Forgeng, N. R. Griffing

The liquidus surface of the C-Cr-Fe system to 1900°C has been mapped from carbon solubility and freezing point measurements, metallographic observations, and published data. In the graphite field, the surface drops precipitously to meet a slope descending from the Cr3C2-C join through the mixed carbide fields to a meandering eutectic valley; this flows from the Cr-C to the Fe-C edge. On the low-cavbon side of the valley, the surface rises to the chromium corner. 1 HE purpose of this inquiry was to gain a more complete knowledge of the C-Cr-Fe liquidus surface. This required an extensive study of carbon and chromium-rich alloys which, in the past, have received the least attention. Sanbongi el al.1 measured the solubility of carbon in liquid alloys containing up to 25 wt pct Cr at temperatures of 1460" and 1545°C and found that it increased with chromium content and temperature. Lucas and wentrup2 also made solubility experiments in graphite crucibles, but at higher chromium contents in the range of 38 to 80 pct and at temperatures of 1550" to 1700°C; however, their experiments were relatively few, and the effect of temperature was not consistent. The present investigation included compsitions ranging from 0 to 94 pct Cr and 1.4 to 11.7 pct C at temperatures up to 1800°C. Saturation experiments in graphite crucibles, thermal analyses during freezing, and metallographic and X-ray diffraction studies were employed to obtain desired information which, together with published data from other investigations about the binary edges and the ternary system at lower carbon levels, made possible the construction of a comprehensive C-Cr-Fe liquidus surface. C-CR-FE LIQUIDUS SURFACE The derived ternary liquidus surface is shown in Fig. 1 where the solid curves are liquidus isotherms. The dashed curves and the binary edges are the liquidus field boundaries of the primary crystals, the arrows along these boundaries indicating their direction with decreasing temperature. Each intersection of three internal boundaries is the composition of liquid involved in four-phase isothermal equilibrium with the three primary crystals whose liquidus fields touch there. It may be observed that a total of six four-phase equilibria occur at melt temperatures. The general topography of the liquidus surface consists of a eutectic valley sloping down from the Cr-C edge at 3.2 pct C to the Fe-C edge at 4.25 pct C. The liquidus surface rises in two directions from the valley, one hillside terminating at the Cr-Fe edge while the opposing hillside rises toward the carbon corner out beyond the top edge of Fig. 1. Both hillsides are interrupted by intersections of surfaces or joints representing the liquid colmpositions of various three-phase equilibria. Seven primary crystals occur, namely a(bcc), ?(fcc), graphite, (Fe, Cr)3C capable of dissolving as much as 15 pct Cr, and three different chromium carbides in which iron is partially soluble by substitution for chromium. The composition ranges of the primary l~hases at melt temperatures are shown

Jan 1, 1962

By H. N. Hall

Various factors must be considered in an engineering evaluation of gravity-drainage reservoirs. Among these are: (1) the effect of producing rate on total oil recovery; (2) the effect upon well productivity and ultimate recovery of the pressure level maintained during the producing life of the reservoir; (3) the economic advantage of full or partial pressure maintenance; and (4) estimate of the rate of gas production and injection and the possible purchase of gas under conditions of full pressure maintenance to ascertain compressor facilities needed. All of these factors can be evaluated only when a reliable method is employed for determining reservoir performance in gravity-drainage reservoirs. The purpose of this paper is to present a general method for calculating the performance of a gravity-drainage reservoir. This method is applicable for conditions of complete pressure maintenance, partial pressure maintenance and normal pressure depletion. Provisions are made to take into account variations throughout the reservoir of reservoir configuration, changes in permeability and fluid composition. Based on the method presented in this paper, an IBM 650 computer program has been developed. The past performance of an actual gravity-drainage reservoir producing under conditions of declining pressure and no gas injection was duplicated using this program. INTRODUCTION In tilted reservoirs the production of oil is influenced by drainage of oil from upstructure to downstructure locations. When this downstructure drainage of oil is sufficient to cause effective segregation of the gas and oil in a reservoir, the reservoir is usually classified as a segregation drive or gravity-drainage reservoir. (Discussion will be restricted to gravity-drainage reservoirs which have no encroachment of edge water.) The important feature in gravity-drainage reservoirs is the density difference between reservoir oil and gas. These phases tend to segregate in the reservoir with the result that in the gas cap the oil saturation is maintained at a higher level by drainage of oil from the gas-cap area. Oil can be produced from the oil zone at a low gas-oil ratio and reservoir energy is thereby conserved. The standard material balance in not adequate for predicting gravity-dramage reservoir performance because it does not take into account the difference in saturation above and below the gas-oil contact. Several authors'.' have presented methods for calculating the performance of gravity-drainage reservoirs in which reservoir pressure is maintained constant by gas injection into the gas cap. Using some simplifying assumptions, these methods can be employed with a desk calculator to give acceptable results. The problem of predicting the performance of gravity-drainage reservoirs under the conditions of declining reservoir pressure is many time more complex than that of constant pressure. fierefore, attempis to develop a method suitable for desk calculation have required excessively simplified assumptions. In the past several years, highspeed digital computers have become more widely available for reservoir engineering problems. These corn puters are well suited to problems such as the prediction of the performance of gravity-drainage reservoirs with pressure decline. Many of the simplifying assumptions necessary for hand computation can be eliminated so that a realistic approach to the gravity-drainage process can be made. CONCEPTUAL PICTURE OF OIL MOVEMENT IN GRAVITY-DRAINAGE RESERVOIRS Before attempting to develop an analytical treatment for conditions occuring in a gravity-drainage reservoir, a concept should be formed concerning the movement of fluids in the reservoir as oil is produced. A review of the literature'.' shows that it is customary to classify gravity-drainage operations into two categories—(1) with complete pressure maintenance, and (2) with declining pressure. The same line of reasoning will be followed in presenting the concept of the movement of fluids in the reservoir because it is easier to visualize the movement of fluids under conditions of complete pressure maintenance. After discussing complete pressure maintenance, an analogy will be made between that and the case of declining pressure. It should be kept in mind throughout that the final aim for the problem of solving gravity-drainage performance with digital computers will be to develop a general program for any kind of gravity-drainage reservoir. COMPLETE PRESSURE MAINTENANCE One feature which is generally common in gravity-drainage reservoirs is a gas cap located at the top of the structure. This is shown in Fig. 1(a). Fig. l(b) shows oil saturations that might occur through the reservoir. In the gas cap, oil saturation is lower than

By Stuart S. Forbes

Changes and additions made to the Canadian Copper Refiners Ltd. electrolytic refinery between 1949 and 1955 are reviewed. The effect of high current density on current efficiency and section work is discussed. OPERATING and physical changes which have been made to the electrolytic tank house of Canadian Copper Refiners Ltd. suggest a review of present conditions. Previous papers1 a have described the general arrangement. Since then, expansion, closer anode spacing, and higher current densities have increased annual cathode capacity from 112,000 to 182,000 tons. A recent extension to the tank house, begun in the spring of 1954 and completed in August 1955, was undertaken to handle the monthly production of about 3,000 tons of anodes from Gasp6 Copper Mines. The anticipation of these additional receipts and large stocks of unrefined copper caused by the increase in custom smelting at Noranda made it necessary to increase production without immediately available additional cell capacity. Accordingly, from December 1954 through March 1955, the tank house was operated successfully at a current density of 24.0 amp per sq ft. Again, as of September 1955, one of the two tank house circuits is being operated at this high density. Although other refineries may operate at current densities higher than 24 amp per sq ft, none is doing so with anodes which contain silver and gold content as high as those being refined at Canadian Copper Refiners Ltd. General Arrangement The original building consisted of two parallel bays, each 660 ft long and 60 ft wide, with a 24 ft pump bay extending along the west side of the building. A previous expansion, completed in 1939, was to the west of the original building and consisted of two 60 ft parallel bays 240 ft long. The length of these two bays was extended in 1954 to 540 ft, adding one stripper and 12 commercial sections to No. 2 electrical circuit. Space is still available for an additional six commercial sections and one stripper section. Construction on these seven sections started in September 1955, and will be completed early in 1956. The tank house capacity will then be 206,000 tons of cathodes per year. In the two tank houses there is a total of 900 cells distributed as follows—commercial, 468; stripper, 36; total, 504 in the No. 1 tank house (No. 1 circuit): commercial, 360; stripper, 36; total, 396 in the No. 2 tank house (No. 2 circuit). Section arrangement consists of nine cells to a tier and two tiers or 18 cells to a section. Anodes, weighing 620 lb each, are cast with a Baltimore groove and are refined by the multiple system. Solution enters each cell through a bottom inlet at one end and overflows at the top of the opposite end. Rate of solution flow through the cells is controlled by valves at each section to 4.5 gpm. Electrical power to the tank house is now provided by nine 675 kw motor generator sets. Each set consists of a 135-12 v 5000 amp dc generator, driven by a 980 hp 2300 v synchronous motor. When No. 1 circuit is operated at 22,000 amp, five sets, at 4400 amp each, are connected in parallel. As the maximum allowable current on No. 2 electrical circuit has recently been set at 18,000 amp, only four sets are connected in parallel on No. 2 circuit. A tenth set, now being installed, will be reserved as a spare, for use in either circuit as required. Recent Changes In 1949, the annual capacity of the tank house was increased from 112,000 to 132,000 tons by closing the

Jan 1, 1957

By Nathaniel Arbiter, Norman L. Weiss

Factors now accelerating the trend to larger concentrators and larger equipment units are reviewed. After almost 40 years of stability with unit sizes less than 100 cu ft, 200 and 300-cu-ft flotation-cell units are now operating and a 500-cu-ft machine is being built. The design of these cells is considered, as is the design and operation of flotation circuits against the background of the need to achieve greater process efficiency while holding down operating and investment costs. Particular attention is paid to the scale-up problem. With the newer cells having five to ten times higher unit capacities, the advantages resulting from this in sampling, mill operation nnd control, testing and plant layout are indicated, as well as the broad direction for changes in the overall design of 50,000 to 100,000-tpd concentrators. A comparison is given of the available larger cells of U.S. manufacture with analysis of differences and similarities. After almost 60 years of application in this country, froth flotation is still by far the most important process for concentrating metallic ores as well as a number of nonmetallic ores including fluorspar, phosphate rock, and potash. Its use on iron ores and coal is increasing. In the metals groups, the largest plants and the greatest progress are found in copper and molybdenum mills, and the section of this paper that deals with applications will be found most pertinent to that field. During its long reign, the flotation process has passed through several phases of evolution and has achieved progress in economy, efficiency. and simplicity of operation. Much of today's success in the flotation of low-grade ores can be attributed to that progress. Even more important to us than our ability to cope with today's conditions are tomorrow's problems, which we can contemplate with some prescience and confidence. Our annual production of copper, lead, zinc, and molybdenum—to mention only the most important metals occurring in the U.S. as sulfides- must be held at a high level in the face of a declining grade of ore. It is probable that the tonnage of such ores mined and processed will double in this country before the turn of the century. Not only will many of the existing flotation mills be enlarged again and again, but larger mills will be built here and abroad to meet our needs. At this moment, in fact, there are at least three proposed new foreign mills or expansions that envision 100,000-tpd milling rate on copper ores. Table 1' shows the trend in copper ore grades in U.S. in recent years. Table 2' shows the projected annual growth rate of consumption 1966-1985. A study by one of the authors 25 years ago showed that of 32 copper mills in North America with more than 100-tpd capacity, only eight had capacities exceeding 10,000 tpd. The average for these eight was 25,000 tpd. These included the three giants of that day, Magna, Arthur, and Morenci; the other five averaged a little over 10,000 tpd. Today instead of the eight mills with capacities exceeding 10,000-tpd capacity we have 25, and the mill with less than 1000-tpd capacity is fast becoming extinct. Much less range is found in lead and zinc mills, which are still generally small except for the few with over 1000-tpd capacity in Missouri, Utah, and Idaho, and a few zinc ore mills in the same size category. Molybdenum and potash operations are the fastest growers in North America today, but when one considers the projected increase in consumption of copper together with the projected decrease in grade of ore (3% annually), he can foresee that copper ore milling will soon lead the list. Technological improvements to meet the challenge of lower-grade ores have taken the wholly predictable path toward bigger equipment. In mining, shovels, draglines, scrapers, and trucks have led the way; in ore processing, we have seen a rapid increase in size of grinding mills, flotation cells, and pumps. Twenty-five years ago, for example, the 10-ft-diam ball mills treating 2000 tpd at Morenci were considered the giants, but today some grinding mills in similar service have five times that capacity. The specific matters to be dealt with in this paper are 1) the underlying principles that affect flotation-machine design, and the conditions required to produce

Jan 1, 1971

By Reginald Williams

THE amount or value of the precious metals consumed in dentistry is probably amazing to most people. It falls very little short of that which is consumed in jewelry. Inasmuch as the ultimate destination is in the human mouth, dental alloys enjoy some importance because life and health depend upon restorations made with them. Prosthetic dentistry has made wonderful progress in the last few years. The manufacturers who supply the metals also deserve commendation. This industry which deals with metals to go-into people's mouths is comparatively new. There is no literature on the subject, and little or no precedent by which to be guided. It was only by close cooperation with the dentist or prosthetic technician that desirable physical properties were produced, as-nearly as possible, in the metals which were available and permissible. It is true that there were and still are conflicting opinions among the dentists as to the physical properties they require. Sometimes they request the impossible, such as alloys which are exceedingly stiff and springy, yet will bend or adjust easily. Even in this latter instance, progress has been made by supplying methods of heat-treatment whereby metals may be softened or hardened at will. (Figs. 1 and 2.) The demands made upon manufacturers are extremely varied. They must supply metals of tensile strengths ranging from approximately 30,000 to 100,000 lb. per sq. in. and over. The latter metals must be workable and in many instances capable of extreme deformation. They must not be affected by mouth conditions, nor should they oxidize greatly when molten, at red heat, or during a soldering operation. In addition to physical, specifications, color demands must also be met. The firm of which I have the most, knowledge manufacturers 11,553 standard stock articles of precious metals, taking into consideration formulas, finenesses, grades, colors, gages, lengths, sizes and weights. If special demands are taken into consideration, the number would be in excess of 25,000. Wrought metals are manufactured in a great many alloys of different sizes and shapes, such as plate, bar, rod, wire, sheet, strip, mesh and foil. There are also other products of importance.

Jan 1, 1928

By W. A. Klikoff, I. Fatt

The concept of fractional wet wattability is examined. Fractional water wettability of a reservoir rock is defined as the fraction of the internal surface urea that is in contact with water. Capillary pressure and relalive permeability of unconsolidated sand are shown to be functions of fractional wettability. INTRODUCTION The petroleum industry has long recognized that wettability of reservoir rock has an important effect on multiphase flow of oil, water and gas through reservoirs. As early as 1928 the American Petroleum Institute sponsored a study of wettability as part of API Project 27 at the U. of Michigan.' Despite 30 years of research, there is still little exact knowledge of the wettability of reservoir rocks. There are two parts to the wettability problem. After agreeing to a uniform nomenclature in regard to wettability,' the first question to be answered is, "What is the in situ wettability of a given reservoir rock?" If this can he answered the next question is, "What part does wettability play in determining the characteristics of multiphase fluid flow through the rock?" This paper represents an oblique attack on the problem of wettability. No attempt is made here to answer the basic question of wettability in situ. instead the consequences of the concept of fractional wettability are examined. Multiphase flow in sandpacks is shown to he highly influenced by fractional wettability. Jennings' has given 3 definition of wettability and the other terms used in discussing wettability. These terms must be applied to the physical situation existing In reservoir rock. A survey of the pertinent literature from 1928 to 1956 indicates that the concept of a contact angle was applied to reservoir rock in the same way it would be applied to a flat, homogeneous surface. Attempts were made to state quantitatively the wettability of a reservoir rock in terms of a contact angle which was presumably constant at all points on the very rough and heterogeneous interior surface of a porous rock. Calhoun, et al,3-6 prepared synthetic consolidated and un-consolidated porous media in which they claimed there was a known uniform contact angle. They then showed the effects on the capillary pressure and relative permeability characteristics of varying this angle. The API Project 47 at the U. of Texas' and others' have made extensive studies of an indirect approach to the contact angle through the use of heat of wetting data. Even if successful. however, this approach also states the wettability of porous rock in terms of a contact angle which is uniform over the entirc surface. If the angle varies from one part to another on the internal surface, there is no way of determining from the measurements the area distribution of contact angles. In 1956 Brown and Fatt5 suggested that the concept of a contact angle, as applied to reservoir rock, be abandoned. This suggestion was made because it is known that the internal surface of most reservoir rocks is composed of many different minerals, cach with a different surface chemistry and a different capacity to adsorh surface active materials from reservoir fluids. Furthermore, the operation of a contact angle in determining the form of a fluid-fluid interface is difficult to picture in the very complex geometry of a pore. Brown and Fatt proposed that the wettability of reservoir rock be stated in terms of the fractional internal surface area that is in contact with water or oil. All surfaces on which there is water are called water-wet; surfaces on which there is oil are called oil-wet. The fractional water wettability is then stated as a number which represents the fraction of the internal surface that is in contact with water. A symmetrical statement can be made for the fractional oil wettability. The concept of a fractional wettability as previously stated has in its favor the recognition of the heterogeneous mineral composition of most reservoir rocks. Another point in its favor is that fractional wettability can be measured quantitatively with relative ease. Hol-brook and Bernard10 se a simple dye adsorption test to obtain fractional wettability of reservoir rocks. Amott11 uses a combination of imbibition and displacement to arrive at a wettability index of reservoir rocks which seems related to fractional wettability in the range 0.25 to 0.75 fractional water wettability. Jennings" has shown the changes in relative permeability that take place when a porous material is changed from unity to zero fractional water wettability. He also shows that reservoir rocks in their natural state, but at room temperature and atmospheric pressure, have relative permeability characteristics which would indi-

By C. N. J. Wagner, E. N. Aqua

The bee alloys of the terminal solid solution of rhenium in niobium were investigated by X-ray diffraclion methods. The analysis of the broadening of the powder pattern peaks from the niobium-rich alloys, cold-worked by filing, showed evidence for faulting on (211) planes. The alloys with larger rhenium concentrations were brittle, and fractured when filed. The analysis of the shapes of the diffraction profiles from powders produced by hammering with steel plates) of these brittle alloys indicated that the broadening was due predominantly to platelets bounded by clibe planes. This result was consistent with the Laue patterns from single-cleazlage facets which showed evidence for clearage fracture on {100} planes. The influence of faulting on the mechanical properties of face-centered cubic (fcc) metals and alloys, i.e., how faulting affects the various dislocation configurations in fcc metals, is well-known.' The important question is whether or not faulting occurs in body-centered cubic (bcc) metals and alloys, and, furthermore, if faulting does occur, to what extent it affects the mechanical properties. Theoretical calculations indicate that the stacking-fault energy is rather high in most bcc metals.2 The results of sev-eral studies using transmission electron microscopy have indicated that faults are present in well-annealed and lightly deformed bcc metals and alloys, such as tungsten,3 vanadium,4 and Mo-Re alloys.5,6 These faults, as have been observed, may be stabilized by the presence of interstitial (C,N,O) atom segregation to the extended dislocations. In addition, there is considerable X-ray diffraction evidence for faulting in bee metals,7-8 using the same techniques that were successful for the study of faulting in fee metals and alloys.7 This X-ray diffraction method is currently the only technique applicable for the investigation of faulting in metals with high stacking fault energies, i.e., when severe amounts of deformation are required to produce sufficient amounts of faulting to be detectable by X-rays. The thinned films of heavily deformed metals will become opaque in the electron microscope due to the high dislocation densities present. In a previous investigation of faulting8 in bee metals of group Vb and VIb, the authors observed that niobium was ductile when filed at room temperature, and showed the highest density of faults on the (112) family of planes. A niobium-base alloy system was therefore chosen to study the effect of alloying on the occurrence of faults in a bcc alloy. There is a large range of terminal solid solubility of rhenium in the alloys of the bee refractory metals. All of the Group VIb-rhenium alloys, i.e., Cr-Re, Mo-Re, and W-Re, exhibit solid solution hardening without loss of ductility.9 In fact, the ductility reaches a maximum for alloys with compositions near to the limits of solubility. This enhanced ductility has been attributed to the lowering of the stacking-fault energy in the alloy; i.e., the increased amounts of twinning provide an additional mode of deformation, resulting in the observed high ductility.' Because of this demonstrated effect of rhenium in bee alloys, it was decided to study a series of alloys of Nb-Re. Using the same X-ray diffraction methods as described in the previous investigation,' one is able to identify the possible causes of broadening of the powder pattern peaks, e.q., particle size, microstrains, stacking faults, and/or twin faults. The separation of these various contributions to the measured peak shape is accomplished by the Warren-Averbach analysis.7 I) EXPERIMENTAL PROCEDURE A series of seven bee solid solution alloys containing from 2.5 to 21.5 at. pct Re (remainder niobium) were prepared at the General Electric Research Laboratory. Buttons, weighing 25 g, were alloyed from electron-beam-melted niobium chips and random rhenium sheet by arc melting in a water-cooled copper crucible, under an argon atmosphere. The buttons were inverted and completely remelted to promote homogenization. The nominal alloy compositions are listed in Table I. Samples of the cold-worked alloys were obtained by filing to produce a powder for the X-ray study. Alloys too brittle to be filed were hammered with steel plates. The resultant filings or brittle impactings were screened through 150-mesh classifiers and compacted to the required shape for the diffractometer holder. The X-ray diffraction peaks were automatically recorded by fixed time counting at uniform 28 intervals, or by continuous registration with a ratemeter. In all cases, the (110)-(220) and (200)-(400) pairs of peaks and the (211), (310), (222), and (321) reflections were measured on a GE-XRD5 diffractometer using CuKa radiation with nickel filter or MoKct radiation and a LiF monochromator in the diffracted beam. The first part of the data reduction, completed with the aid of a series of programmed computations,10 was the analytical resolution of the Kol component of the diffraction profile. Subsequent computations were then made with reference only to the resolved Kol peak shape. These included the measurement of the

Jan 1, 1967

By E. S. Bumps, W. F. Craig, M. Baeyertz

Metallurgists have looked at fractures macroscopically for many years and have evolved a vocabulary in which such words as "cleavage," "brittle," "shear," "ductile," "granular," "fibrous," and "silky" are used to describe the appearance of the fractured surface; but the meaning of these words in terms of metal structure is not well established. Observations of the structural meaning of "brittle" and "ductile" fractures in plate steels have been made, notably, by Kramer and coworkers1 and by Tipper.2 Grossman3 has studied the fracture of tempered martensite and combinations of ferrite and martensite. Notwithstanding these and other less concerted attacks on the problem, present understanding of fracture rests more on assumptions and logic than on experiment. It is the purpose of this paper to add a little to the growing fund of experimental observations of the nature of fractures in steel. The particular fractures to be described were obtained in conventional impact testing of an ordinary structural steel shape. In impact tests of the Charpy type, the specimens fail in a characteristic manner that depends on the steel and the temperature of testing. With ordinary structural and many other steel products, an appropriate range of testing temperature will cause a considerable change in the energy absorbed before fracture. This change is known as the energy transition and is accompanied, more or less closely, by alteration in the appearance of the fracture. At testing temperatures below the transition, the terms "brittle," "cleavage," or "granular" are used to describe the fracture; above it, "ductile" or "shear" are often used. Within the transition, the fracture changes from "brittle" to "ductile" by a progression in appearance, wherein the "brittle" portion of the fracture becomes restricted to a smaller and smaller central area of the fracture, as the testing temperature is raised and the "ductile" type of fracture is approached. All this is well known to metallurgists. The specimens under consideration are of the conventional V-notch Charpy type. They were taken from a structural steel shape of the following analysis: C Mn P S Si 0.17 0.46 0.009 0.029 0.03 Both longitudinal and transverse specimens were tested and examined. Fig 1 shows the energy values plotted against testing temperatures in the usual way. The curves for both longitudinal and transverse specimens show an energy transition, although the maximum energy absorbed at testing temperatures above the transition is greater in the case of the longitudinal specimens. Fig 2 illustrates the changes in the macroscopic appearance of the fractures that are associated with the energy transitions shown in Fig 1. Macrographs of the fractured surfaces of the specimens have been identified with the fracture ratings at intervals on each fracture curve. The numerical fracture rating on the ordinate of Fig 2 indicates the percentage of the area of each fracture that was considered to be "brittle" on macroscopic observation. Such rating of the fracture type in impact tests is now customary in many laboratories. Hereafter the specimens will be identified by reference to Fig 2 as 90 pct "brittle," 80 pct "brittle," and so on, in accordance with this macroscopic evaluation of the appearance of the fractured surface. The discussion of the fractures is divided into three parts. The first two are concerned with the mode of fracture and its relation to general structural features. As the same metal-lographic features occur in both longi-

Jan 1, 1950

This listing of members is arranged to show company affiliation The primary breakdown is by state or country, then by company name and political subdivision At the end of each major group is a general list showing members affiliated with schools or colleges and those who did not indicate any company affiliation The listing, for countries outside United States, is broken down generally by continents and alphabetically within the continent by countries The various countries are indexed on the preced¬ing page *-The asterisk indicates members available for consulting work Anyone desiring to be listed with AIME as available for consulting work can do so by sending a written request to the office of the Secretary.

Jan 1, 1952

By J. F. Poland

Location of Basins and Geologic Features of Occurrence: The major ground-water resources of California occur and are stored in the many large alluvium-filled valleys of the state. The deposits of Quaternary age which hold the ground water commonly are called valley fill. Meinzerl has discussed the characteristic features of this fill and showed that for western United States its distribution is concentrated chiefly in western Utah, Nevada, central Oregon, California, southern Arizona, and central New Mexico (see fig. 1). For California the principal ground-water basins are shown on fig. 2. Except for the Mojave Desert and the "Basin and Range" Valleys (fig. 2, Nos. 23 and 23A), which are not shown individually, the basins outlined on fig. 2 contain all the large reservoirs in valley fill within the state. The Sacramento and San Joaquin Valleys (fig. 2) together comprise the Great Central Valley of California, which has an area of about 18,000 square miles. The Sacramento Valley contains about 5000 square miles of valley lands, approxi- mately equal to the area of Connecticut; the San Joaquin Valley embraces about 13,000 square miles, equivalent to the areas of Massachusetts and Connecticut combined. Both the area and the ground-water use in the Central Valley is far greater than for all the other shaded alluvial basins of fig. 2 added together. Except for the Sacramento Valley, all the major ground-water basins of the state are south of Sacramento. The valley fill in these ground-water basins has been transported by streams and most of it has been laid down in alluvial fans, producing the typical alluvial-fan structure of aquifers radiating as tongues from a prismatic pile of coarse, permeable debris at the canyon mouths; these aquifers are encased down slope by poorly sorted materials consisting of a clayey matrix with imbedded pebbles and boulders, interbedded with flood-plain silt. In the deeper inland structural valleys, the alluvial deposits interfinger at depth in the valley bottoms with horizontally bedded lacustrine sand, silt, and clay. The San Joaquin Valley is a good example. In the coastal valleys exposed to the sea, such as the Los Angeles coastal plain, the alluvial fans pass coastward into lagoonal and thence to shallow marine deposits. In all these basins, the gravel is coarsest and most permeable near the apexes of the fans, but tongues or lenses of clean gravel and sand may extend for many miles down the fan. Thus, these water-bearing structures are in a position to absorb stream flow near the canyon mouths and to transmit it through the buried radiating conduits.

Jan 1, 1951

By William B. Senseman

FoR reasons well known to mining engineers, wet grinding is quite universal in plants having to do with the extraction of metallic values from crude ores. In the processing of the nonmetallic and industrial minerals, dry grinding is the more common method. The crude materials usually contain less moisture than is required for wet grinding and the products usually are marketed in dry form; most of them as powders. To grind wet, therefore, would entail the addition of water and an expense for drying the product, which is not justified. Furthermore, the material would be a dried cake that would still have to be pulverized or disintegrated before use. For producing fine products, air separators have largely replaced the earlier practice of sizing with screens and bolting reels. Mills in which the air-separating feature is an integral part of the design are now commonplace. Mill designs are many and air systems have developed along various lines, but for the purpose of this discussion, only the fundamental idea need be emphasized— the idea of using air for sizing and removing pulverized material from a grinding mill. About 20 years ago, when the use of mills equipped with air separation had become common practice, heated air or gas was introduced to such a system for the removal of moisture. The purpose of this discussion is to outline the developments and trends that have followed this experiment. It is an important development, for mills equipped with air separation are now universally used for pulverizing not only nonmetallic and industrial minerals, but a great variety of other materials. All such mills are essentially the same. Dried material is pulverized, removed by an air stream, trapped in a cyclone collector, and relatively clean air from the cyclone is returned through a fan to the mill. There is no theoretical need for a vent from the system. The practical need is to vent the air that leaks into the system; and, since the cyclone is not 100 per cent efficient as a dust collector, this vented air carries some dust with it. The initial attempt at drying was made on a system like that described, by the addition of a furnace. The minus pressure within the mill draws hot gas from the furnace. Infiltration air, along with the drying gases and evaporated moisture, is vented as before. The first application was made to a mill used for pulverizing coal. The coal contained very little moisture, so very little drying effect was needed for the success of this experiment. Actually, some calculated efficiencies of over 100 per cent were obtained before due allowance was made for the conversion of mill power into useful heat. When moisture is low, the heat obtained from the conversion of milt power is an appreciable part of that required. That drying can be effected in the short time interval available in a grinding mill of this type is better understood by visual-

Jan 1, 1948

By R. M. Brick, R. G. Treuting

DESPITE the basic importance of slip in the plastic deformation of metals, and the considerable experimental investigation, thought, and speculation that have been devoted to the fundamental nature of these processes, surprisingly few data have been reported regarding the microscopic appear- [ ] ance and distribution of slip lines,[$] the external manifestation of the slip process. Photographs hitherto reproduced in the literature are in general at low or unspecified magnifications with no correlation to the prior shear. A single-crystal cylindrical tensile specimen of alpha brass about ½ in. in diameter, one of many previously prepared by H. L. Burghoff,1 was available for study. A plane about 3/16 in. wide, parallel to the specimen axis and normal to the plane containing the slip direction and the specimen axis, was ground and metallographically polished along the entire 5-in. gauge length. Heavy etching produced a surface free of both scratches and flow. The specimen was strained in tension until slip markings first became visible on the polished surface (Figs. I and 2). Restressing the crystal caused additional markings to appear at an initially lower [ ] stress than previously was required. Stretching the specimen to produce a dense concentration of slip lines caused such variations in level in the polished surface (normal to the slip direction) that microscopic study at higher magnifications became impossible. After annealing 15 hr. at 850°C., the specimen recrystallized to form two grains with a boundary approximately normal to the specimen axis and about midway along its length. Each was X-rayed, and two planes were again polished along the length of the specimen, in this case each parallel to the slip direction in one of the two crystals. A light longitudinal scratch parallel to the specimen axis was drawn down the center of each plane. A Huggenberger extensometer was attached to the crystal A, whose slip plane would have the higher resolved shear stress of the two, and the specimen was again strained in tension.

Jan 1, 1941

By Oliver C. Ralston

A definite field of usefulness has developed for the brine-leaching processes of removing lead from ores and other products, so this paper reviews the developments, both in practice and in research, that have taken place since the publication of two earlier papers on this subject.' Several commercial plants are now in operation and a number of semi-commercial test plants have been operated in an effort to determine the limitations of brine leaching and to compare the results with other forms of treatment. Briefly, the brine leaching of lead depends on the fact that lead chloride and lead sulfate are soluble in saturated sodium-chloride solutions. In dilute brines, the solubility of the lead salt is less than in pure water; but in the strong brines, the solubility is greater than in pure water due, supposedly, to the formation of a double sodium-lead chloride. This is seen in Fig. 1, which shows the results of M. Demassieux2 on the solubility of lead chloride in sodium-chloride solutions of different concentrations and at three temperatures. The curves are not those given by Demassieux but are calculated from his results in order to convert them to units common in metallurgical work. The right-hand branch of each curve shows that if the solution is kept in contact with solid sodium chloride the lead chloride can be almost entirely displaced from solution, but that brines which are saturated with sodium chloride, but are not in contact with the solid salt, have a very high solubility for lead chloride. The diagram gives the analysis of the solution in grams of lead per liter, although the substance actually in solution is lead chloride. At 100" C. as much as 100 gm. of lead per liter can be obtained; but at lower tem-

Jan 1, 1924

By Walter L. Maxson, Fred C. Bond

THIS paper is a continuation of two earlier papers, l, 2 and presents new data on the grindability of various ores and other materials-the results of several years of intermittent research work on the nature of grinding and interpretation of test results. It is divided into five parts: 1. The tabulated results of several hundred grindability tests on a wide variety of ores. 2. A method of correcting screen analyses and calculating from them the surface and other properties. 3. A description of a new method of measuring the "surface energy" of an ore by pendulum impact tests. 4. Test results. 5. A general discussion of the test results and their application to grinding problems. 1. GRINDABILITY OF VARIOUS ORES This part is a continuation of the paper listed as reference No. 1. The method of testing is described in detail in that paper. The sample to be tested is crushed to all through 6 mesh in rolls set at x6-in. opening in closed circuit with a screen. Of this sample 700 C.C. is ground dry in a laboratory ball mill under constant conditions of mill speed and ball charge in closed circuit with a screen of the desired size at 250 per cent circulating load. The mill is cylindrical, 12 by 12 in., and rotates at 70 r.p.m. It contains a charge of 285 iron balls weighing 20,125 grams and ranging from 1 ½ to ¾ in. in diameter. Each test is continued for a sufficient number of periods to establish equilibrium at 250 per cent circulating load, or until the composition of the circulating load is constant for successive periods. Tests are conducted at the mesh size to which the ore is to be ground in practice, and the results are expressed as the net production in grams of screen undersize per revolution of the mill. This is designated as the

Jan 1, 1938

By Leon W. Dupuy

Many articles have been written describing peculiar and particular types of drilling. Little correlation has been made between the character of ground to be drilled and sampled and the type of drilling most desirable for procuring satisfactory samples. In development work, the engineer and metallurgist often desire the recovery of a sample in as physically natural a condition as possible, particularly when the sample must provide material for process tests as well as chemical and physical analyses. This paper describes the results of experimentation in drilling unconsoli-dated materials carrying titanium minerals in the Magnet Cove area, Ark. The drilling was most difficult in that the ground varied much in consistency, and it was vitally necessary to recover a physically natural sample. Ordinary churn drilling recovered a sample that could be analyzed chemically, but the sample was not in its natural state. The problem was successfully solved by utilizing and further developing methods used in the oil and clay industries. In the Magnet Cove area of Hot Spring County, Ark., the titanium minerals include rutile, brookite, ana- tase, leucoxene, and others. They occur in soil, clays, and altered rocks adjacent to novaculite in contact meta-morphic deposits. In preparing titanium minerals for use in the industry, it is necessary to know the physical characteristics of the ore. Also it is believed that the particular physical character of the titanium mineral used is just as important as the chemical character. Brookite and rutile, for example, are the same chemically but differ in crystalline structure. In preparing titanium minerals for market, beneficia-tion is necessary. For the millman to make a satisfactory laboratory test, the sample he uses must be as nearly of the same physical character as he would have from mine run ore. In the past at Magnet Cove, churn drilling had been done on the properties, and assays of total titania had been obtained. It was found, however, that the total titania was indicative merely of the presence of titania but did not tell the metallurgist the character of the material or even give him the slightest indication of what he might expect to recover. When the Bureau of Mines entered the field in the winter of 1947 and 1948, it was therefore necessary that a natural sample be recovered. LIMITATlONS IN ORDINARY PRACTICE The churn drilling that had previously been done had shown that the occurrence of titanium-bearing mineral was somewhat widespread. The samples were, however, completely beaten up and in a finely powdered state. The minerals had been slimed, and such ore dressing tests as were made from the churn-drill samples were found to be worthless. Test pitting and outcrop sampling had provided satisfactory samples of surface ore but did not represent the entire ore body. A quantity of rutile had been produced from the surface residual concentrations in the westerly part of the cove, but production ran into metallurgical trouble as depth was attained. Representative deep samples upon which ore dressing research might depend were needed.

Jan 1, 1950

Continued Discussion of the papers of Van Hise, Emmons, Weed and Lindgren, Bans., xxx., 27, 177, 424, 578. See also the papers of Vogt, Kemp, Rickard, Blake and Lindgren, at pp. 125, 169, 198, 220, 226, and also the final contribution of Prof. Van Hise, p. 284 of the present volume. All the foregoing, together with the discussion here following, are included in the special volume, "The Genesis of Ore-Deposits," issued this year by the Institute. H. Foster Bain, Des Moines, Iowa (communication to the Secretary):* The zinc- and lead-deposits of the Mississippi valley, which it has been my fortune to study, give particularly good examples of many of the principles of ore-deposition formulated by Prof. Van Hise. Perhaps there is nowhere clearer evidence supporting his fundamental tenet., that ore-bodies are to be regarded as a result, and as merely one of the phases, of the work of underground waters. The facts regarding the mines of the upper Mississippi valley have been given in some detail for Wisconsin by Prof. Chamberlint and, more recently, for the mines west. of the Mississippi by the Iowa Geological Survey.‡ Fortunately, also, the processes of underground water-circulation have been studied in some detail in connection with the investigation of artesian waters throughout the region.$ In Missouri and Arkansas the mines and ore-bodies have been much studied ; but the general problems of the circulation of underground waters have been neglected. During the season just closed the writer has been engaged in a re-study for the United States Geological Survey of the zinc- and lead-deposits of the Ozark region, with special reference to those of the . Joplin area; and his full report is now in preparation. It has been interesting to note how fully the statement that the orebodies result from the general action of underground waters is

Jan 1, 1902

Jan 1, 1881

By William B. Senseman

FoR reasons well known to mining engineers, wet grinding is quite universal in plants having to do with the extraction of metallic values from crude ores. In the processing of the nonmetallic and industrial minerals, dry grinding is the more common method. The crude materials usually contain less moisture than is required for wet grinding and the products usually are marketed in dry form; most of them as powders. To grind wet, therefore, would entail the addition of water and an expense for drying the product, which is not justified. Furthermore, the material would be a dried cake that would still have to be pulverized or disintegrated before use. For producing fine products, air separators have largely replaced the earlier practice of sizing with screens and bolting reels. Mills in which the air-separating feature is an integral part of the design are now commonplace. Mill designs are many and air systems have developed along various lines, but for the purpose of this discussion, only the fundamental idea need be emphasized— the idea of using air for sizing and removing pulverized material from a grinding mill. About 20 years ago, when the use of mills equipped with air separation had become common practice, heated air or gas was introduced to such a system for the removal of moisture. The purpose of this discussion is to outline the developments and trends that have followed this experiment. It is an important development, for mills equipped with air separation are now universally used for pulverizing not only nonmetallic and industrial minerals, but a great variety of other materials. All such mills are essentially the same. Dried material is pulverized, removed by an air stream, trapped in a cyclone collector, and relatively clean air from the cyclone is returned through a fan to the mill. There is no theoretical need for a vent from the system. The practical need is to vent the air that leaks into the system; and, since the cyclone is not 100 per cent efficient as a dust collector, this vented air carries some dust with it. The initial attempt at drying was made on a system like that described, by the addition of a furnace. The minus pressure within the mill draws hot gas from the furnace. Infiltration air, along with the drying gases and evaporated moisture, is vented as before. The first application was made to a mill used for pulverizing coal. The coal contained very little moisture, so very little drying effect was needed for the success of this experiment. Actually, some calculated efficiencies of over 100 per cent were obtained before due allowance was made for the conversion of mill power into useful heat. When moisture is low, the heat obtained from the conversion of milt power is an appreciable part of that required. That drying can be effected in the short time interval available in a grinding mill of this type is better understood by visual-

Jan 1, 1948