Search Documents

By L. R. Weisberg, E. A. Miller

Single-crystalline films of silicon of good quality were vacuum-deposited on sapphire. The improved crystallinity was achieved by the strict exclusion of oxygen from the evaporation system, including the use of a "oxygen-free" silicon source. To minimize possible contamination of the source, the silicon was sublimed from the solid at about 1390° C. using a simple electron bombardment system to heat the silicon. This resulted in deposition rates of about 5 to 7 µ per hr and film thicknesses of 4 to 20 µ. The vacuum during deposition was ordinarily about 5x 10-8 Torr, DESPITE the success achieved in the chemical vapor deposition of silicon on sapphire using Silane,1-4 vacuum deposition has not provided comparable properties. For example, Chu et a1.5 vacuum-deposited silicon on single-crystalline substrates of A12O3, Sic, ThO2, and other compounds, and, although some epi- but the use of ultrahigh vacuum (about 1 to 3 x10-9 Torr) during deposition did not significantly improve the results in the oxygen-free system. The crystalline quality of films deposited on (0001) sapphire was found to be considerably superior to (1102) sapphire surfaces. Using (0001) sapphire, single-crystalline films were deposited at temperatures as low as 780° C and as high as 1075°C, with the best crystalline quality obtained at about 1000°C. At this temperature, hole mobilities over 250 sq cm per v-sec were achieved. taxy was indicated, single-crystalline films were not produced. More recently, Salama, Tucker, and young6 evaporated silicon on single-crystalline sapphire, but only poor crystallinity was observed, and low carrier mobilities were measured. In the present experiments, good-quality single-crystalline films of silicon on sapphire have been achieved by specifically excluding oxygen from the evaporation. This included not only the use of a "clean" vacuum system but, of special importance, the use of an oxygen-free silicon source. This has also been shown to provide a dramatic improvement in silicon homoepi-taxy.7 As a result, silicon-on-sapphire films with hole mobilities over 250 sq cm per v-set were achieved, and single-crystal films were grown as low as 780°C and as

Jan 1, 1969

By G. M. Ritcey, A. W. Ashbrook, E. G. Joe

Solvent-in-pulp extraction of uranium from acid leach slurries of flotation concentrates is described. Solvent extraction was carried out in a 10 in. diam pulsed-plate column. The extractant was a 0.1 M tertiary amine (General Mills Alamine 336) in a kerosene diluent containing isodecanol as an emulsion suppressor and third phase inhibitor. In pilot plant operation at the Beaverlodge mill of Eldorado Mining and Refining, Ltd., slurry feeds containing up to 35% solids were processed at a throughput rate of 13.5 tpd of dry feed. Uranium extraction obtained was as high as 98%. Amine losses to the raffinate were approximately 0.07 lb amine per ton of original dry feed. The Beaverlodge Mill of Eldorado Mining and Refining employs a carbonate leach for the extraction of uranium from the ore.',' Prior to carbonate leaching sulphides are removed by flotation to reduce reagent consumption. This flotation concentrate containing some uranium is then leached with sulfuric acid, filtered, and the uranium precipitated with magnesium hydroxide. The precipitate is then returned to the carbonate leach circuit. Although the tonnage of flotation concentrate treated by acid leaching is low, reagent costs are relatively high. Also maintenance costs on the acid leach filtration circuit were beginning to show significant increases. The choice of solvent extraction-in-pulp as an alternative to the present circuit was influenced by the following factors: 1) elimination of acid pulp filtration, 2) increase in overall recovery because of soluble loss elimination, 3) reduction of reagent cost (mill sodium carbonate solutions are used as strip), and 4) production of higher purity precipitate at the mill site. Because a solvent-in-pulp process would be difficult to test on a bench-scale, the Eldorado experience in the use of pulse columns,3-5 mixer-settlers,6 and solvent-in-pulp operations in particular7 was applied directly to the initial pilot plant carried out during the summer of 1965 and followed by the second pilot plant in 1966. The latter work, which is presented in this paper, determined the following factors for anticipated scale-up to plant production: 1) overall uranium recovery by this process, 2) tonnage throughput expected, and 3) solvent losses anticipated for the full-scale plant. The equipment used consisted of a 10 in. diam extraction pulse column and three mixer-settlers for scrubbing, stripping, and acid equilibration. All equipment was designed by Eldorado and much of the pilot plant was built at the mill site. PROCESS CHEMISTRY Feed to the acid leach plant consists of a sulphide flotation1,2 concentrate containing mainly pyrite, uranium and graphite, with a particle size of 90%

Jan 1, 1968

By G. L. Oldright

NEARLY all of the present schemes for treating complex (i. e. lead¬silver-zinc-copper) ores are based on the idea that lead holds, and will hold for some time, the strongest economic place from the viewpoint of supply and demand of all the non-ferrous metals. Copper, it is thought, will come back to its own when European affairs are stabilized, although at that time competition from Chile, Peru, and Katanga, in particular, will be more severe than in pre-war days. The future for silver and for zinc is uncertain. New uses are developing for zinc, and the market has remained better than many expected, but the stabilization of world markets will bring in foreign competition instead of relief. The cost of producing zinc from simple zinc ores, by the retort process, will, from the nature of the labor required and the increasing cost of fuel, increase steadily. As a result, the small producers of purely zinc ores around Joplin are shutting down their mines, even with a good market price for zinc; on the other hand, the producer of lead from complex ores, in the Rocky Mountain states, is confident of a profit from the sale of his lead, and is seeking means to make the zinc in his ore pay some part of the cost of treatment. However, the tonnage costs for mining and ore dressing are much higher in the Rocky Mountain states, as may be seen by comparing tax-return statements from the various states. Even before the recent drop in the price of silver, many mines were operating on a very slender margin of profit; labor and supplies cost more. Mining at greater depth has shown most orebodies to grow increasingly more complex, so that improvements in mining and ore-dressing practice have not been sufficient too compensate for the additional expense involved in beneficiating these ores. The smelters have had to meet the same general economic situation, so they can only give

Jan 3, 1924

By A. E. Bellis

THE CHAIRMAN (ALBERT SAUVEUR, Cambridge, Mass.).-Any information likely to throw light on the constitution and proper treatment of high-speed steel in order to obtain maximum results, should surely he welcomed. All users of high-speed steel, I believe, will agree with the authors that, in order to obtain satisfactory results, it is not sufficient to heat all brands of high-speed steel to one and the same temperature; apparently very slight differences of chemical composition seem to call for marked differences in temperature. I think that all of us agree that a properly treated piece of high-speed steel should have a fine austenitic or polyhedral structure and that an appreciable quantity of free carbide may be present in the case of very high tungsten steels. What we seem to lack is a satisfactory method, quick and reliable, of ascertaining when the proper structure has been obtained. I think Mr. Bellis' paper is a step in the right direction. To the untrained eye, however, it is not an easy matter to select from some of his photomicrographs the one representing the best structure; for instance, in the case of steel A, we wonder why temperatures of 2,250 and 2,300 do not yield the same results, seeing that both structures are apparently alike, and the same might apply to some of the other samples. I have no doubt, however, that the experienced observer is capable of detecting structural differences that are not made plain here and by which he is able to select the proper quenching temperature. COLIN G. FINK, East Orange, N. J.-On page 68 the authors say that the use of a barium chloride bath to eliminate this difficulty has the disadvantage that the surface of the tool becomes decarbonized." I would like to ask whether they actually found that the surface was decarbonized, or whether they base this conclusion on softening alone? A. E. BELLIS, Springfield, Mass.-No, we have never demonstrated that it was a decarbonization, it is just the softening of the steel. The addition of ferrocyanide to the ferrochloride bath has been suggested. I think that is not altogether satisfactory, because the ferrocyanide bath changes composition very rapidly at these high temperatures, and it would be just a question of luck whether or not it had too much or too little ferrocyanide in the bath giving equilibrium with the carbon content.

Jan 4, 1917

CONTENTS PAGE SOUTHWARD, GLENN B.-Coal Mining by the V System. Discussed by Glenn B. Southward, Howard N. Eavenson, Edward B. Raiguel, Thomas de Venny, J.. J. Rutledge, Graham Bright 1 ARMS, RAY W.-Dry Cleaning of Coal. Discussed by Ray W. Arms, S. A. Taylor, Howard N. Eavenson, W. R. Crane, F. F. Jorgenson, G. R. Delamater. 6 EAVENSON, HOWARD N.-Data About Labor Employed in Various Bituminous Coal Mines. Discussed by Howard N. Eavenson, George H. Ashley, E. A. Holbrook, S. A. Taylor, R. V. Norris 14 Coal Mining by the V System Discussion of the paper of GLENN B. SOUTHWARD presented at the New York Meeting, February, 1924, and issued as Paper No. 1300-C, with MINING AND METALLURGY, February, 1924. MEMBER.-How do you pay your men for loading? GLENN B. SOUTHWARD.-Everything is on time basis. MEMBER.-How many men do you have loading across one of the diagonal faces? GLENN B. SOUTHWARD.-From four to five, depending on the length of the face. Our loaders are so arranged that each will give about twenty-five tons per loader a day. MEMBER.-How much timber do you use? GLENN B. SOUTHWARD.-A little more than will be used in room-and-pillar work, but not a great deal more. We have not attempted to recover much of our timber. MEMBER.-IS the mine union or non-union? GLENN B. SOUTHWARD.-Non-union. HOWARD N. EAVENSON, Pittsburgh, Pa.-I went .through that mine some weeks ago, and think that the author has been very conservative in his statements about the amount of loadings, etc. EDWARD B. RAIGUEL, Huntington, W. Va. (written discussion).¬Page 7 shows 60 men employed in day and night shifts, inside the mine, producing 750 tons per day. Let us reduce these figures to a man-hour basis, for comparison with Mr. Eavenson's figures on West Virginia mines, as follows:

Jan 6, 1924

By Samuel Lasky

WITH the movement of American capital into foreign investment, a new field of specialization for the American mining engineer is gradually opening a field hitherto entered almost wholly by chance and without full appreciation of its possibilities. Our age has been fitly called the "Age of Specialization." The special application of one's knowledge and ability to a definite and restricted branch of .his profession is purely a modern condition. Any profession, or branch of a profession or, industry, in which the problems may be segregated into definite types, calls for specializa-tion. Modern industry demands efficiency and that, reduction and ultimate annihilation of waste. Effort and time wasted by workers' on a problem with which they are not familiar is as flagrant a waste of money -the final standard-as any waste of materials. One of the subdivisions of mining engineering which is beginning to be recognized is of engineers who are clearly conversant with the particular and peculiar problems obtaining under foreign operating conditions. The need is as yet obscured, however, by the domestic prosperity of our American mining industry. The opportunity here lies more with the American engineer than with other nationals. The foreign en-gineer now in that service is not there through a realiza-tion of the special opportunities that exist, but through necessity, whereas, with the American engineer, more especially ,the recent graduate or those who will soon graduate, this is a new field to be entered wholly by choice. As a matter of fact, many engineering students will find it necessary to seek foreign service if they wish to remain in mining. Although the scope of the domes-tic industry is tremendous and there are many positions open to the junior engineer, there are not enough for the great number of graduates turned out yearly from our, mining schools. Educators tell us that less than 40 per cent. of the students in engineering schools gradu-ate; and of these but a minority continue in engineering. Even this minority is too great for our domestic. In-dustry, and although the young engineer realizes that condition after a few years he rarely seeks foreign work. A. perusal of the directory of the American Institute of Mining Engineers indicates that, but about one-half of one per cent of the Junior Associates are in positions outside of North America. Granting that most of them are still in school, the figure is surpris-ingly small.

Jan 1, 1927

By William Glenn

The taking of proper samples of crude ores seems to he less thoroughly understood, or less carefully practiced, than its impor tance requires. We all know how often we encounter the reports of very accurate assays and analyses, the weight of which as evidence wholly depends on the method of obtaining the sample, and is very probably nil, because there has been no proper sampling. Pissages might be cited from technical books, and from current technical literature (all the work of writers whom we delight to honor) to show that even among high scientific authorities there is too little acquaintance with the practical art of the sampler. There is no metallurgical or chemical establishment which does not frequently receive samples truly representing nothing. They consist usually of bits of ore, or what not, selected because they are worse or better than the average of what they are meant to represent. And they are worthless, no matter who made the selection. Where conscious choice is permitted to enter into the operation, a fair sample will not result, unless by a miracle. The work of sampling is often looked upon as within the realm of boys and of pensioners only. At least, though the manual labor be left to subordinates, the principles on which it is conducted and the safeguards with which it is surrounded are not unworthy of the study of experts; and experts should he ready to teach these principles and enforce them in practice. For exact sampling is the indispensable first step towards learning the value of any boxful, carload or shipload of ore. I propose to give a simple account of the method of sampling by hand, such as I have always pursued. There is nothing new about it. So far as I know, it is the immemorial old method, as old at least as Cornish copper-mining. Perhaps my fellow-members in the Institute may suggest improvements in it. If not, it will constitute a record in our Transactions to which laymen and beginners may be referred.

Jan 1, 1892

By H. H. Power, C. H. Pishny

When an oil operator becomes a party to a proration agreement he may wonder, with good cause, whether production prorated .today is merely deferred until tomorrow or whether oil might be lost. Various types of evidence obtained from production records when studied quantitatively are of great assistance in arriving at definite conclusions. A study of individual examples cited in this paper leads towards some solution of the problem, particularly when they are considered in the aggregate. Many production curves on various pay horizons were studied. A disappointingly large number of these were of contributory value, but inconclusive. However, there were enough curves of similar type from the Wilcox sand at Earlsboro, Bowlegs, Seminole City, the Cromwell horizon at Little River, and the Simpson dolomite at Valley Center, Kansas, from which reasonably definite conclusions were drawn. Assuming that deferred production is later made up with no increase in ultimate recovery, a curve (Fig. 1) shows the normal flowing and pumping life of a composite well, contructed by the family curve method. The initial production of the well shown is 1700 bbl. daily and the allowed production is 25 per cent. On this basis the average daily allowed rate for the first month is 425 bb1., or the area BCDE, which is equivalent to the area AFDG under the normal decline curve. The potential production for the second month is 1500 bbl. and the allowed production 375 bbl. daily. By this procedure a potential curve for each succeeding month is obtained (points A, H, I, J and K). If the well is opened it should produce somewhere near its potential curve for a short period and then decline at a more rapid rate than the potential curve. This theoretical analysis is basic. Actual examples exhibiting all points raised by the ideal curve are rare. Proration in the Mid-Continent area has been effected mostly by leases rather than by individual wells; hence a well may produce any

Jan 1, 1931

By Sidney A. Swensrud

About a year ago, I attempted in a general way to trace the origin and development of some of the marketing problems of the petroleum industry, and to describe certain trends which it then seemed possible to foresee. To summarize briefly, it was pointed out that the consumption of gasoline, after increasing for more than a decade at an almost unbelievable rate, was slowing down, but that the two factors which determine the supply of gasoline —-namely, the production of crude oil and the percentage of gasoline derived therefrom—were tending steadily to mount. It was suggested that, while the increase in gasoline outlets began with and probably was justified at the start by the rapidly increasing demand, long after all reasonable requirements as to number of outlets had been met the number continued to increase—if anything, at a still more rapid rate—because by that time the overproduction of crude had begun to exert an impelling urge upon the owners of that crude to seek assured outlets for it in the form of gasoline. As more and more companies became integrated all the way from crude oil to marketing, there took place an ever-increasing competition among them, not only for the existing outlets but for new ones. The wide margin between wholesale cost and retail price, which is characteristic of the early stages of most new industries, persisted in the oil industry longer than in most industries, for various reasons. The existence of that wide margin provided in large measure the means of attracting new outlets, for as the gallonage per outlet declined with the increasing number of outlets, competing companies simply offered the dealers a larger part of the total margin. The very nature of competition suggests that such a process would continue until practically all of the available margin was thus given away, and such was clearly the tendency. It was a system that in turn produced increasing marketing expense per gallon on account of the diluted gallonage per outlet; this increased expense might seem to have provided a justification for continuing wide margins. Economics, like its parent, nature, however, progresses by mutations and so began to throw out new types of marketers, in the form of tank-car service stations, cut-price jobbers, and the like—heretics or

Jan 1, 1932

By James Terry Duce

The symposium on production for the year 1940 contains few papers on the foreign situation. It is probable that the foreign part of next year's symposium will be even shorter. This is due to rigid censorship in various countries, as the question of the volume of petroleum supplies has become one of great strategic importance. This is even more true than in the last war, owing to greater mechanization of armies. 'It has always been the policy of officers in charge of the symposium to refrain from publishing information that might possibly injure national or private interests. At the close of the war we hope again to publish full and accurate records of production abroad. Excerpts from Circular to Authors In order to facilitate interpretation of the data in this chapter, we print the following excerpts from the Circular to Authors. The field is the unit in this tabulation. In cases of fields extending across State boundaries, such as Rodessa, it is suggested that each State author treat the section of the field in his State as a unit, and by a footnote indicate that the field extends into an adjacent State. Each space in Table I may represent one of four possibilities; either it is not applicable to the particular field, or the proper entry is not determinable, or the proper entry may be determinable but is not determinable from data available to the author, or the proper entry is determinable. When spaces are not applicable, leave blank; in spaces where the proper entries are determinable but not de-terminable frod data available to the author, please inserty; in spaces where the proper entries are determinable by the author, make such entries. y implies a hope that in some future year a definite figure will be available. The entry of a zero is a positive declaration, and an important declaration where it is in order. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In sucli cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces the correct entries represent the opinion of the author (for example, "Area Proved') and in such cases the entry need not be hedged to such extent as when the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use x. It is thought that the nearest whole numbers are sufficiently accurate for our purposes except as to percentage of sulphur in oil. If an author desires to report any other figures to tenths, he may do so. The quantity of gas produced should include, where possible, gas sold or otherwise marketed, and gas blown into the air, burned as flares or otherwise wasted. Segregation of these figures would be interesting if the authors can make such segregation. In any event, the figures should represent as nearly as possible the total quantity of gas removed from the reservoir. Under the columns on "Depth," the average depth to the top of the productive zones and to the bottom of the productive wells, when

Jan 1, 1941

By N. Brown

From the theories of flow and fracture it is shown that the difference in reciprocals of the transition temperatures (OK) is a quantitative measure of temper ernbrittlement. Experimental data are given which support this conclusion. STUDIES of temper embrittlement have been made with various viewpoints; some involved a study of the kinetics of the reaction,',2'" others were concerned with changes in the mechanical properties," . and still others investigated the structural differences between the embrittled and unembrittled states by means of the microscope," -ray ,' measurements of electrode potential," and electrical resistivity." In all these studies, the difference in impact properties was the criterion for distinguishing between the embrittled and unembrittled states. By common agreement the difference in transition temperatures is now taken as a measure of the degree of embrittlement, and this measure is used as the quantitative measure upon which studies of the phenomenon are based. Vidal and Jolivet"' suggested that the degree of embrittlement was the same whether measured by impact or by a slow bend test. Their conclusion was based on tests at constant temperature. Jaffe and Buffum" using the impact and slow bend test showed that, for a given degree of embrittlement, the difference in transition temperatures varied with the method of testing. Hultgren and Chang" showed that the difference in transition temperature produced by the V-notched Charpy impact test was not the same as the value produced by the keyhole-notched impact test. This is a very fundamental point because there can be no true measure of temper embrittlement unless it is invariant with respect to the test method. Theory The purpose of this analysis is to show how the transition temperature depends on the stress distribution and the state of the material. The criterion for fracture may be stated as follws: where iF is some function of the principle stresses and F is a critical condition depending on the state of the metal. Similarly yielding occurs when Where is another function of the prin-ciple stresses and Y is a critical value depending on the state of the material. There is some controversy as to the exact form of the function f,.(u,, u,, us) but most experimental data give the following criterion:= where 8, and 6, = 21 or 0. Combinations of 6, and 8, give the various criteria such as the normal stress, the hydrostatic tension, and the maximum shear stress laws. Agreement is general that the octahedral shear stress law adequately describes the yield condition. where the bracketed factor will be called the design factor and depends on the stress distribution. Whether the metal decides to yield or fracture is given by the condition that The effect of temperature and strain rate upon Y has been studied by various investigators, It has been shown by MacGregor and Fisher" that

Jan 1, 1955

By Joseph F. Shirley

A froth flotation plant to recover byproduct molybdenite must be designed specifically for the selected separation process and the type of ore being treated. However, some general rules concerning byproduct molybdenite plant design can be suggested that would be valid for most processes. The term byproduct molybdenite in this paper is limited to the recovery of molybdenite from copper porphyry ores, which essentially amounts to selectively separating molybdenite from copper and iron sulfide concentrates. In addition, most of the discussions would apply only to the almost universally used approach of floating the molybdenite and depressing the copper and iron sulfide minerals. Thickener It is considered essential that the feed to a byproduct molybdenite plant be thickened prior to being treated for molybdenite recovery for the following reasons: 1) Thickening allows the rougher and any preconditioning stages to be operated consistently at the optimum percent solids. 2) Generally, the size of equipment used for pretreatment and the rougher flotation is considerably smaller and less expensive than if the copper flotation concentrates were treated directly. 3) The removal of as much water as practical by thickening removes flotation reagents added in the copper flotation circuit, especially frother which can be quite troublesome in a byproduct molybdenite plant. Although thickening of the molybdenite plant feed has long been recognized as necessary to optimum metallurigcal results, very often this area has been designed poorly. The thickener should be sized so that it can produce a consistent thickened product containing 60 to 65% solids without the use of flocculants. Some plants are only able to thicken to 45 to 50% solids consistently while other plants let the percent solids vary from 45 to 60% over a 24-hr period. While the former is more desirable than the latter, in many cases better metallurgical results could be obtained if the percent solids could be held consistently close to 60%. Probably the simplest and most satisfactory system of handling the thickener underflow is to spigot it into a sump, using a sphincter type valve for the orifice, controlled by a density meter. Another satisfactory approach is to use an ODS type pump to meter the underflow. There are other methods of handling thickener underflow which work satisfactorily as long as the amount of copper concentrates entering the thickener is relatively uniform. However, they often fail to operate satisfactorily when there are large fluctuations in the thickener feed rate due to fluctuations in ore tonnage and/or copper grade. If the percent solids in the plant feed could be held close to 65%. There is the possibility the molybdenite plant tailing would not have to be thickened prior to the copper filter plant. This means that the molybdenite rougher float would have to be conducted at 45 to 50% solids with all the cleaner tailings returned to the rougher for dilution. Admittedly, in some situations this approach would be impossible, but if capital or plant area is limited, it should be considered.

Jan 1, 1981

By W. T. Allan

RAW bituminous coal has been in general use as a blast-furnace fuel in Scotland for the last century, and although its use has now been largely abandoned and it has been replaced by coke in the majority of the few furnaces which are at, present in blast in this country, coal-smelted pig iron is not yet a thing of the past; it is still being produced and mar-keted in competition with the more cheaply smelted product of the coke-fired furnace. Various factors have influenced this change in practice; the once plentiful deposits of coal of a suitable nature for the blast furnace are now not so easily obtainable; native blackband and clayband ironstones which are easily smelted in the coal-fired blast furnace, although still far from being exhausted, are not available except at a. cost that is somewhat higher than that of imported ores, making them unattractive to the ironmaster that is compelled by circumstances to smelt his iron at the lowest possible cost. Within the last 15 years overproduction of synthetic nitrogen has led to progressive reductions in the price of sulphate of ammonia, the recovery of which together with the other by-products before that time materially assisted in reducing the working costs of the coal-fired furnace. Now the sale of the by-products recovered yields a diminished profit. When the cost of the product is the only consideration the small, slow-smelting, coal-fired blast furnace cannot compare with its large, modern, coke-fired competitor. Other `considerations do not by any means all support the same side of the argument. In the smelting of pig iron to be used in the manufacture of steel where the quality of the final product depends so largely upon the control of the conversion process and so much less upon the physical quality of the pig iron used, the physical properties of the pig iron do not exert any appreciable influence upon the quality of the steel produced, therefore the methods employed in the smelting of the pig iron matter but little so long as the requisite chemical composi-tion is reached. On the other hand, in ironfounding where the simple melting of the pig iron, which is the only treatment it receives before being cast into its final form, does little or nothing to modify its original charac-

Jan 1, 1937

By Walter Renton Ingalls

Metallurgical literature has no record of any ore beneficiated for cadmium alone, and the cadmium of commerce is derived from zinc ore, with which cadmium is generally associated. Zinc ores free from cadmium—e.g., the ores of the Franklin and Stirling mines, New Jersey, and of Broken Hill in Rhodesia—are rare. Blende concentrates of 50 to 60 per cent grade have contained (in production of important tonnage) as much as I per cent Cd, which is unusually high. The concentrates from the Tri-State district average from 0.3 to 0.4 per cent Cd, which is high. The concentrates from mines west of the Rocky Mountains seldom are higher than 0.2 per cent. In the periodic system of the elements, cadmium is in the same group with zinc. Its properties and compounds are similar. Its metallurgy is also similar. Cadmium has a melting point of 320°C. and a boiling point of 778"C., while the melting point of zinc is 415'C. and the boiling point gos°C. These conditions, together with the lower reduction temperature of cadmium oxide, indicate means for. separating cadmium from zinc. Cadmium in spelter is viewed, if not as an impurity, at least as an alloying element that may be objectionable, its special effect being hardening. However, for some purposes, a little cadmium in spelter is desired, and 0.4 per cent may be permissible, even in spelter for rolling. Cadmium in spelter for brassmaking is completely volatilized at the temperature of that process, and in bygone days an immense quantity of cadmium must have been lost in the fumes from these furnaces. Pyrometalltjrgy—Early Cadmium compounds, sulphide and oxide, being more volatile than the corresponding compounds of zinc, loss of cadmium begins to occur from the first furnace operation. In normal roasting, even with Tri-State ore, this loss may not be very high. Raw ore, assaying 0.4 per cent Cd, may be expected to give a roasted product of the same assay, which would imply a cadmium loss of about 15 per cent. Roasted ore, assaying 0.4 per cent Cd when distilled at ordinary furnace temperature, yielded spelter containing about half of that in the ore charged. The first draw of spelter under these conditions may assay 0.8 per cent Cd (accounting for 22 per cent of the cadmium recovery) and after the several draws of spelter have been equalized the cadmium content may average 0.35 per cent. If, therefore, 2000 lb. of blende averaging 0.35 to 0.4 per cent Cd is roasted and distilled, there may be obtained 1000 lb. of spelter, assaying 0.35 per cent Cd or 3.5 lb. content, which entering into Prime Western spelter will be sold at the spelter price. It will be observed from the outline hereinbefore (summarizing conditions prior to the introduction of sintering) that the main loss of cadmium occurred in the distillation process and by failure to condense, which could be ameliorated by attaching a prolong to the condenser, thus collecting

Jan 1, 1944

By H. E. Nold

ThE raw materials of the ceramic industry are mostly clays. This raw material is ground, water is added and the mixture pugged into a moist, plastic, rather stiff mass. From this mass the desired units of manufacture are made (bricks, hollow building tile, sewer pipe, etc.). These units are dried; then placed in kilns and heated until the desired degree of vitrification is obtained. For firing ceramic ware, two distinct types of kilns are used; namely, periodic and continuous tunnel. Periodic Kilns Periodic kilns are those ordinarily seen in a brick plant. They are either round or rectangular. The raw, dried, formed ware is piled or set in the kilns to depths frequently exceeding 10 ft. The kiln is heated until the ware is matured, then gradually cooled sufficiently to allow men to remove the ware; then the cycle is repeated. The time duration of the cycle may be more than two weeks. In order that heat can be distributed uniformly throughout the pile or setting, the units are placed so as to leave open spaces or flues throughout the pile for the passage of the hot gases. Each kiln is provided with a number of fireboxes (usually 10 or 12) spaced equally in the outside wall. The fireboxes may be equipped with flat or inclined grate bars or they may have no grates at all (dead bottom). Down-draft kilns are most used. In these the hot gaseous products of combustion from the fireboxes are deflected upward by bag walls just inside the fire zone. From the top of the kiln the gases are drawn down through the setting, off through holes in the kiln bottom, and conducted to a stack or stacks. In up-draft kilns the fireboxes are usually set somewhat lower. The hot gases are drawn inward and upward through the ware and pass off from the top. Up-draft kilns find their greatest use in the firing of common brick. In either case the problem is to maintain, as nearly as possible,

Jan 1, 1934

By A. G. McGregor

IN THE Southwest a number of large steel chimneys discharge the gases from the copper smelting furnaces. Some of these chimneys show no deterioration after twenty years, others show serious deterioration after tour years service. A steel stack 20 ft. 7 ½ in. (6.3 m.) in diameter by 279 ft. (85 m.) high, Fig. 1, used for roaster gases only at the Calumet & Arizona Mining Co.'s plant at Douglas, Ariz., was lined to the top of the bell, 40 ft. (12 m.) from the base, with common brick placed on end, lime and cement mortar being used. Above the bell, the stack was lined with 4 by 4 by 8 in. (10 by 10 by 20 cm.) building tile, placed on end, making a lining 4 in. thick. The tiles were supported on angle-iron rings, riveted to the inside of the chimney shell about 15 ft. apart. The chimney was put into use in the latter part of 1913. Four years later, considerable of the tile lining had fallen out of place and mixed with the flue dust at the bottom of the chimney. About a year later, several . flattened and distorted sheets were noticed about 70 ft. below the top. An investigation showed that the thickness of these distorted sheets, which was originally ¼ in., had been reduced one half. One year later, or six years after the chimney went into use, several holes, a square foot and smaller in area, appeared near the flat spots mentioned. Soon afterwards, when the chimney was shut down for repairs, it was found that most of the tile lining for 125 ft. from the top had fallen out and that the steel shell was badly corroded; but where the lining remained in place the shell was undamaged. Many of the tile which had fallen out of place had become soft or flaky and crumbling, others were as hard as when placed. An analysis of the hard and soft tile is shown on p. 2. These tile were of a fireclay mixture, and were used instead of common brick on account of lower cost. The steel forming the upper 125 ft. (38 m.) was replaced, and a 4 ¼ -in. (11-cm.) lining of firebrick was laid from the bell to the top of the chimney. The brick were placed on end, wedges and keys being used. After each 8-in. course was set, keyed, and wedged tight, thin mortar -water, sodium silicate, and finely ground silica-was worked into the joints. The brick are supported on angle-iron rings, every 15 ft., in the same way as the tile.

Jan 1, 1921

By W. B. Daly, A. S. Richardson

The application of artificial refrigeration, or air-conditioning, to the ventilation of deep, hot mines has long been a subject of interest to the operators of such properties. Artificial cooling of the air in theaters, railroad coaches, and various industrial plants has been so successful within recent years that it has been natural to assume that the adoption of similar methods would afford a ready solution to the difficult problem of mine ventilation. It should however, be obvious, that although there may be nothing technically impossible in the application of this process to mine ventilation there is a great economic distinction between the maintenance of a high standard of comfort for a large number of people in a relatively small space such as a theater and the cooling of air to improve working conditions for miners scattered throughout the extensive workings of a large mine. Many methods of air-conditioning have been considered by the management of the Anaconda Copper Mining Co. at various times, but until the development of the process to be described in this paper none has seemed economically practicable. The Ventilating Problem at Butte The main obstacle to satisfactory ventilation in the Butte mines is the normally high temperature of the granite country rock. In the present operating zone, rock temperatures as high as 120' F. have been noted, and in some parts of the district the rate of increase of temperature with depth has ranged as high as 3.5" F. per 100 ft. Other factors, such as the decay of mine timber and the oxidation of sulfide minerals in the ore bodies, contribute to raise the temperature of the air in the working places but, particularly in the development of the mines to greater depth, the naturally high temperature of the rock is of predominant importance. In few other places, probably, are the ordinary ventilating measures more hindered than at Butte. At an operating depth now exceeding 3000 ft., all of the air required for ventilation must pass through timbered shafts which, because of heavy ground, are of small size and offer great resistance to the flow of air. Shaft compartments are rarely more than 4.5 X 5 ft., and the shaft area open to the flow of air usually does not exceed 65 sq. ft.; in only two shafts is the area as great as 85 sq. feet.

Jan 1, 1934

Discussion of the paper of A. P. WATT, presented at the St. Louis meeting, October, 1917, and printed in Bulletin No. 130, October, 1917, pp. 1476 to 1563. THE CHAIRMAN (0. M. _BILHARZ, Miami, Okla.).-Mr. Watt's reference to sorting or hand-picking of the ore in the lead district, which is being introduced at Mine La Motte, is especially interesting. I believe, from my former experience in the district, that hand-picking should be practised to some extent by all the companies in the Lead Belt. I know that a great many thousand tons containing only very small amounts of lead are passed through the mills, which, of course, is not to the advantage of milling machinery. That procedure may be Warranted at times of high prices, but I think that hand-picking should ordinarily be adopted to some extent: ERNEST GAYFORD, Salt Lake City, Utah.-On page 1525, speaking of the settling of slime previous to treatment either on slime tables or by flotation, Mr. Watt states: "The settling area allowed per ton of dry slime varies from 11 to 16 sq. ft.-an average for the district would be about 13 sq. ft. of settling area per ton of dry slime. This figure applies when the, discharge contains 20 per cent. solids." Mr. Ramsey, of the Dorr company, is here and I would like to ask him whether a settling area of 13 sq. ft. per ton of dry slime per 24 hr. is not considerably above the average area of Dorr settling tanks, and whether 20 per cent. solids is not above the general dilution for that' capacity? I should also like to know what is the general average on slimes of that character. E. R. RAMSEY, Denver, Colo.-An allowance of 13 sq. ft. per ton does seem rather large. I am not familiar with the settling characteristics of the dolomitic gangue, but as an average over the country, I should say that 6 or 7 sq. ft. would be nearer correct for discharge at that consistency. L. A. DELANO, Bowie Terre, Mo.-We have had an opportunity to try our tanks at the highest capacity, and-find that by thickening the slime to 30 per cent. solids we average 12 sq. ft. per ton of dry slime. ERNEST GAYFORD.-DO you find any definite ratio between the thickness of the discharge and the settling capacity of the tank? Do you consider that the tank has a larger capacity if the discharge is 3 to 1 than if it is 50 per cent. solids? L. A. DELANO.-I think it has greater capacity with the thinner discharge. It depends a good deal on the density of feed to the tanks; in our case the feed contains 2.5 per cent. solids.

Jan 1, 1918

By J. Burns Read, Charles H. Fulton

A previous article1 by the authors contained a general description of the new roasting furnace herein described but it did not go into detail as to the metallurgical behavior or the results obtained. Believing that such information would be of great value, they have elaborated on the subject and have given many unpublished details. The furnace described applies the principle of roasting finely divided zinc-sulfide ores, now produced in large quantity by the flotation process, in gaseous suspension; that is, the ore particles are carried, in suspension, in a current of air and gaseous products of the roast. The relatively great fineness of flotation concentrate presents difficulties and problems of roasting in furnaces of the ordinary type; the fine ore is forwarded through the furnace in the form of a shallow bed and its very fineness leads to dense impervious bedding which prevents oxygen from reaching the interior of the bed, thus unduly lengthening the time of roasting and preventing the elimination of the last of the sulfur. The fineness of the concentrate, normally, should lead to a rapid and complete roast, for the speed of roasting is a function of the surface exposed to oxygen, which surface is greatest, per unit of weight, in very fine material. The difficulty in bed roasting is to get the oxygen to the particle. If the fine ore, during the roasting, could be freely suspended in oxidizing gases, full advantage could be taken of the great surface conferred by its fineness. This fundamental idea, of course, is not new, for the Stedtefelt furnace, familiar to the older metallurgists, is an example of it; but the manner in which this is accomplished may be new. The numerous efforts to roast in gaseous suspension show that the idea is attractive; in fact, an analysis would indicate that it is the most reason-

Jan 1, 1925

By Blamey Stevens

(Butte Meeting, August, 1913.) THE following paper aims to make a full explanation of the phenomena of rock jointing: It may be unnecessary to give any general description of what are termed joints in rocks, but Professor Geikie's clear and faithful generalizations are so illuminating that no excuse need be given. for introducing the following and other quotations into this paper "Almost all rocks are traversed by vertical or highly inclined divisional planes termed joints. These have been regarded as due in some way to contraction during consolidation (fissures of retreat) ; and this is no doubt their origin in innumerable cases. But, on the other hand, their frequent regularity and persistence across materials of very varying texture suggest rather the effects of internal pressure and movement within the crust." 1 General Explanation.-In this paper I show that the phenomenon of jointing may to a large extent be accounted for by the pressure of the water contained in the pores of the rock. To understand this, each constituent grain of the porous material may be considered to be separately compressed by the water which submerges it. As all the grains are held together by cohesion, the whole mass is contracted by this pressure. In an indefinitely extended mass, however, there must be a limit to the possible contraction without rupture, because the material is restrained from moving freely by other material around its boundaries. The mass of rock thus becomes broken up. This phenomenon is known as '" shrinkage " jointing. The term " shrinkage " is an apt one, if it be understood that the shrinkage of the rock is often brought about by change of stress. Stresses.-The compressive component of water stress on the individual grains is evidently the same as that of the water with which it is in contact. This is so, both before and after the jointing is formed. Before the jointing is formed there is, however, a tensile stress in one or more directions which keeps the material from contracting. .

Jan 7, 1913