Search Documents

By E. Teghtsoonian, K. G. Davis

Cobalt crystals of commercial purity have been tested in tension. Their resolved shear stress-shear strain curves are very similar in form to those for zinc, magnesium, and cadmium. There is an initial linear region for shear strains up to around 150 pct, the ratio of work hardening slope to shear modulus at room temperature being about 2 X x This is followed by an upturn, which is, PLASTIC deformation in metal single crystals with close-packed structures has been found strongly dependent on stacking-fault energy. The high stacking-fault energy hexagonal metals magnesium, zinc, and cadmium have been quite extensively tested, but up to now no data have been available for a comparable hexagonal metal with low stacking-fau1t energy' An however, smaller in magnitude for cobalt than for the other metals. Values for the critical resolved shear stress rise from 97 kg per sq cm at room temperature to approximately 170 kg per sq cm at -196 °C. The Cottrell-Stokes ratio is not constant either for variations in the strain rate or for temperature changes, its value decreasing with strain. investigation into the plastic deformation of cobalt, which has a very low stacking-fault energy, has therefore been undertaken. EXPERIMENTAL PROCEDURES Cobalt crystals in the form of rods 0.3 cm in diam were grown in an electron-beam floating-zone refiner at a rate of zone travel of 25 cm per hr. Details of the growing procedure are given in Ref. 1. The zoned cobalt rods had the following analysis:

Jan 1, 1963

By Y. Jeannin, C. Mannerskantz, F. D. Richardson

Measurements have been made between 1040o and 1300°C of the equilibrium between chromium metal, chromic oxide, hydrogen, and water. The results are in closer agreement with those deduced from recent thermal data than with previous equilibrium values. They lead to the equation ?G°1300°-1600°k = -266,700 + 59.95T ± 300 cal for the formzation of a mole of Cr2O3 from chromium and oxygen. This same equilibrium has been studied with the chromium dissolved in solid iron, and in this way chromium activities in Fe + Cr alloys have been established. The measuremenis show that there are substantial positive deviations from ideality in the a, and b phases, and support the results obtained by Heymer and Kubaschewski against those of other investigators. There is considerable disagreement between existing data,1"4 which is referred to in the Discussion, concerning the equilibrium Cr2O3 + 3H2 = 2Cr + 3H2O [l] There is also substantial disagreement between the results obtained by various investigators5-' who have measured the activities of chromium in its alloys with iron by the Knudsen effusion vapor pressure method. In view of the importance in metallurgical processes of chromium and its oxide and of Fe-Cr alloys, an attempt has been made to study equilib- rium [I] both with pure chormium metal and with chromium alloyed with iron, at temperatures between 1040o and 1300oC. From the work with the alloys it is possible to derive the chromium activities from the relationship

Jan 1, 1963

By Howard Smith

OF late considerable experimental and, theoretical interest has been shown in the rates of transformation from a single phase, usually a supercooled solid solution, into one or more phases. Such reactions may involve both diffusion and transformation of the major constituent, as in iron alloys, or it may simply involve diffusion, as in superstructure forma-tion and in age-hardening systems. Most of the work has been confined to ferrous alloys1-9t although two investigations have been made on copper alloys10,11. That such work may be of considerable, practical importance has been demonstrated by Bain12, by the workers at the Kaiser Wilhelm Institut fur Eisen-forschung13,14, and by the everyday use of precipitation and age-harden-inn principles15. Experiments in this country have generally followed Davenport and Bain's technique of rapid supercooling followed by isothermal treatment. In Germany16,17 the work has been extended to the study of the influence of accurately controlled and measured rates of cooling. The work on steel indicates that there are two subcritical temperature ranges where reaction starts sooner after quenching and proceeds at a more rapid rate than at other temperatures. At subcritical temperatures above Ar" where reaction is dependent upon atomic migration there is a period of time of which the length depends upon the alloy content and the temperature, before which no reaction has been detected. Daven-port and Bain1 find that different sorts of atoms in solid solution in gamma iron affect the length of this "prereaction" period differently, manganese

Jan 1, 1935

By R. J. Borg, C. E. Birchenall

The self-diffusion coefficients for a iron have been deternzined between 980° and 1167° K using Fe55 as the tracer. With decreasing temperature the diffusivity was found to decrease more rapidly than predicted by the Arrhenius equation in the region of the Curie temperature. The diffusion coefficients obtained well above the temperature of the magnetic transformation are more precise ard differ substantially from all the previously reported values. In the temperature region beginning at least 50" above T,, the diffusion coefficient is given by D = 118 (±2) exp 1 HE self-diffusion coefficients for a iron have been reported previously as the result of four independent investigations The general lack of agreement and the poor precision of most of the previous work prompted the redetermination by the present authors. The possible effect of the onset of ferromagnetism upon the diffusivity5 provided an additional impetus for this investigation. The earlier measurements of Birchenall and Mehl1 gave low values for the diffusion coefficient at temperatures below the Curie temperature, Tc. However, the precision of these measurements is not sufficient to establish an indisputable correlation between the low values and the magnetic transformation. The results of this investigation along with all the previous ones are shown in Fig. 1. EXPERIMENTAL Small rectangular samples, approximately 1 by 0.5 by 0.3 cm, of high-purity iron (Vacuum Metals Corp., "Ferrovac") are first heated in hydrogen at 900°C for24hr in order to remove possible trace amounts of dissolved carbon and oxygen. The small

Jan 1, 1961

By John F. Elliott, David L. Schroeder

SURFACE depletion can be a significant source of error in the use of the effusion method for determining the thermodynamic properties of alloys, particularly in the case of solid alloys.' However, as yet this problem has not been treated quantitatively by experimentalists in the field.1-3 The method necessitates diffusive transport of material out of the source alloy to obtain a relevant measurement. The general character of the system is shown in Fig. 1. The diffusive flux (nD) at the alloy surface is equal to the effusive flux (nE): where D is the diffusion coefficient of the diffusing substance, C is its concentration, X is the distance from the surface into the source alloy, p is the density of the alloy, and AS is the actual available surface of the alloy. The concentration of the diffusing substance at the surface is CS, and Here fE is the Clausing factor, AE is the area (sq cm) of the orifice, y is the activity coefficient of the substance in the alloy, PO is the vapor pressure (Torr) of the pure substance, M is the molecular weight of the effusing species, and T is the absolute temperature. The differential equation for diffusive transport in the source alloy is Fick's second law. Its solution is dependent on the geometry of the source alloy. Two boundary conditions must be established to obtain the proper solution, the first being Eq. [1], or its equivalent. The solutions for several important forms of the source alloy are considered below.

Jan 1, 1967

By E. H. Miller, E. J. Hall, M. J. Flak

It is well known that, with the exception of the so-called " niter-and-nails " method, all methods used for the fire-assay of salphide-ores,* especially those of iron, zinc, lead and copper, are very tedious and require the constant attention of the assayer. The objections to the niter-and-nails method are: The liability of the charge to boil over, due to the presence of the' niter; the low results in silver (uncorrected); and the frequently large discrepancy between the actual weight of the lead button and the calculated weight. In many cases the buttons are too small to collect all of the gold and silver contained in the sample, while in others they are too large for cupellation. It was thought that, if these objections to the niter method could be eliminated, it mould give a method for the crucible-assay of sulphide-ores, and especially the low-grade ores of zinc and copper, which would be superior to any method in use at the present time. The only similar methods of assay are those of Perkins,t Rhead and Sexton,$ and Mitchell. The method of Perkins requires too much litharge for it to be a commercial success; that of Rhead and Sexton, utilizing the prelimiilary assay we found to be the best;—the charge for the final assay, however, was modified by having borax-glass added to it; also, the oxidizing power of the niter mas determined by a charge which difters from either the preliminary or the

Jan 1, 1904

By C. H. Mathewson, A. U. Seybolt

As is well known, many questions affecting the properties and uses of a metal cannot be answered without careful consideration of the state of purity realized in the various operations of preparation, refining, or special treatment that have brought the product to its final state. The occurrellce of an impurity in minute quantity offers no guarantee that its effect will be inconsiderable because dissolved substances often modify the properties of a metal quite out of proportion to their concentration. In such cases the determination of solid solubility must be accepted as a problem of considerable difficulty, requiring the use of especially purified materials and methods not ordinarily used in the metallurgical laboratory. This aspect of the equilibrium between metals and their oxides is especially important and a search for fundamental data reveals little except conflicting opinion even concerning the systems of common occurrence and interest. Rhines and Mathewson1 in 1934 studied the solubility of oxygen in solid copper by annealing to equilibrium in air and gave reasons for the failure of other methods, notably the ordinary procedure of heat-treatment followed by microscopic examination, to yield reliable results. In this paper, a similar study has been made of the solubility of oxygen in cobalt. The simple theory of this method is outlined below. Conditions of Equilibrium between a Metal and Dissolved Oxide at Different Temperatures and Pressures The general conditions of equilibrium in any system are conveniently summarized in a projection of the triple curves of the P, T, X space

Jan 1, 1935

By Frank G. Snyder

INTRODUCTION Numerous deposits of lead and zinc sulfides, often accompanied by barite and fluorite, occur in carbonate host rocks throughout central and eastern United States. So similar are the deposits in broad general characteristics that they long have been classified as Mississippi Valley type. They differ widely, however, in details such as metal ratios, age of host rock, type of ore-bearing structure, and probable time of mineralization. The theories developed to explain the source and transport of the metals are many and are known to all. The deposits have been termed telethermal on the basis of their presumably shallow occurrence and the attempt to relate the metals to the classic hydro- thermal sequence. 1t is now recognized that deposits of this type can occur at any depth; the only depth limitation is thickness of the sedimentary section. Ideas on the source of the metals also have changed, A rapidly growing body of evidence suggests that the metals were brought by concentrated brines from nearby sedimentary basins. The hypothesis preferred today by many geologists postulates that the metals were deposited during the course of normal sedimentation in depositional basins of miogeosynclinal or orthogeosynclinal type. At some time after deposition of the sediments, the metals were carried out of the basins by migrating brines; the brines moved laterally and upward into structurally high areas; they entered any reservoir-like structure, either primary or secondary in origin, that happened to be available; in this reservoir, possibly in a sulfur-rich environment, the metals were precipitated as ore minerals.

Jan 1, 1970

By A. U. Seybolt, C. H. Mathewson

As is well known, many questions affecting the properties and uses of a metal cannot be answered without careful consideration of the state of purity realized in the various operations of preparation, refining, or special treatment that have brought the product to its final state. The occurrellce of an impurity in minute quantity offers no guarantee that its effect will be inconsiderable because dissolved substances often modify the properties of a metal quite out of proportion to their concentration. In such cases the determination of solid solubility must be accepted as a problem of considerable difficulty, requiring the use of especially purified materials and methods not ordinarily used in the metallurgical laboratory. This aspect of the equilibrium between metals and their oxides is especially important and a search for fundamental data reveals little except conflicting opinion even concerning the systems of common occurrence and interest. Rhines and Mathewson1 in 1934 studied the solubility of oxygen in solid copper by annealing to equilibrium in air and gave reasons for the failure of other methods, notably the ordinary procedure of heat-treatment followed by microscopic examination, to yield reliable results. In this paper, a similar study has been made of the solubility of oxygen in cobalt. The simple theory of this method is outlined below. Conditions of Equilibrium between a Metal and Dissolved Oxide at Different Temperatures and Pressures The general conditions of equilibrium in any system are conveniently summarized in a projection of the triple curves of the P, T, X space

Jan 1, 1935

By N. A. Ziegler

CONSIDERABLE work has been and is being done on the changes of physical properties that take place in alloys at elevated temperatures, and much information on this subject is published. Much less is known, as pointed out by Rickett and Wood,1 about reactions between the alloys and atmospheric gases and still less is known about changes within the alloy itself under the influence of heat and given atmosphere. Moreover, most of the work published has been done on the alloys of "heat-resist-ing" type, in which chromium is an essential ingredient, the behavior of all other alloys being quite unknown, except perhaps of decarburization produced at the surface by oxidizing atmospheres. It has been shown' that iron, with total amount of foreign ingredients not exceeding 0.01 per cent, if heated in an oxidizing atmosphere at above 900° C., may be saturated with oxygen to 0.1 per cent. It was suspected that something of a similar nature may take place in iron-silicon alloys (transformer material), the mechanism of such processes being either a direct diffusion of oxygen into the alloy, or oxygen combining with silicon to form Si02 or more complicated (silicate) inclusions. Another possi-bility to be considered was that during annealing in oxidizing atmos-pheres, when scale is being formed, silicon may oxidize preferentially at the surface, thus impoverishing the alloy in silicon. In collaboration with Dr. T. D. Yensen,3 the writer set out to investigate this problem about two years ago in order to settle these questions.

Jan 1, 1934

HAVING told you of the practices of the arts involving other metals, I wish to tell you also of the practice of that of tin.* Indeed, since this is an easily melted metal, in common use for the utensils which are made for human needs, it is an art known not only to skilled men but also almost to children, wherefore I could proceed with- out telling of it. However, besides the production of plates and bowls and many other dishes for eating from and keeping things in, this embraces two other arts, both of which you should know about because they are useful and beautifid. One of these is the art .of making the letters with which books are printed, and the other is that of making the sheets from which organ pipes are built. The vessels, as perhaps you have seen, are cast one by one in moulds made of white tuff. Several pieces fastened together are then put on the iron axle of a wheel rotated by hand, and [138v] they are turned with a slightly bent tool which has a cutting edge. In this way they are made thin and of a good shape. Then they are polished with a piece of linen cloth and a little powdered tripoli, and thus they are finished. The letters for printing books are made of a composition of three parts of fine tin, an eighth part of black lead, and another eighth part of fused marcasite of antimony.t The desired quantities of these metals are melted

Jan 1, 1942

By L. L. Davis

The rapid increase in the use of pulvcrulent adsorptive materials in the so-called "contact filtration" process for decolorizing lubricating oils makes it desirable to consider some of the basic principles involved. The commercial methods and types of equipment now used arc fairly well known, having been extensively described in the trade journals. In spite of this very little has been published concerning the factors which must be considered in the selection of a process or of a decolorizing ing material. It is commonly understood that contact filtration more or less closely follows the laws of adsorption. These principles have been thoroughly drscribed by Gurwitsch.' The contacting of neutral mineral oils seems to be adsorptive in character and apparently follows Freundlich's law of adsorption which may be expressed by the formula: X = Color material adsorbed hy the clay. M = Amount of clay used. C = Concentration of color material after equilibrium. A and P = Constants for a given oil and clay. Fig. 1 shows the decolorization curve for a natural, dark colored cylin-der stock when contacted with various quantities of clay, curve R being made with natural Riverside Texas fuller's earth and T being made with an acid-treated clay from Texas. As the Tag-Robinson color is inversely proportional to the depth of color, the reciprocal of these colors ran be assumed to be a funct ion of the concentratlion of coloring matter. The values of and C' can, therefore., br calculated by using the reciprocal Tag-Robinson colors, and when these

Jan 1, 1928

G. R. DELAMATER,* Steelton, Pa. (written discussion t)..-Under the heading, "Preparation of Coal," Mr. Campbell discusses the ad-visability of sizing the coal for the jigs. While I fully realize that conditions alter cases, my method at all times is to do everything possible to avoid sizing. It would be unwise for anyone to say that greater ash and sulfur reduction is impossible by sizing. The thing that can be questioned is, will the greater reduction be sufficient to counterbalance the greater cost? The same thing is true of the proper size of crushing for each individual proposition. In past years many washeries have been built and equipped for wash-ing two or more sizes, but I know of few instances where these plants were operated more than a year before sizing was abandoned. Perhaps in some of these cases this was clue to lack of sufficient development of such scheme of operation; yet I have found that most men engaged in this work, including myself, started into the work with a pretty well-fixed idea that sizing would be beneficial. But trials and tests showed that the mixed size washing is necessary for coals requiring crushing to 1 in. or less. Coal is of low value, compared with other minerals segregated by washing or concentration, for which reason simplicity must be the watchword: simplicity in the machine used to attain the separations of impurities from the coal, in the accessory plant equipment, and in its arrangement.

Jan 12, 1919

By Robert Berggren

THE hot-milling process for reconditioning rock-drill bits is not new. It has been employed by a few mines for years and in the past decade it has been widely adopted, as its advantages have become better known. Because of the extensive commercial development in England and Canada of machines to operate on this principle, general acceptance has been largely in the British possessions and until recently has been chiefly in the field of conventional steel. In the past two years there has been a definite trend toward hot-milling of detachable bits in Canada, t but only in the past year has any considerable attempt been made to build special machines for this type of work. Generally a machine designed for con-ventional steel has been used and special holders employed to manipulate the bit. As early as 1934 at least one operator in the United States had adapted hot-milling to conventional steel with a substantial saving in resharpening costs. Several other operators have taken it up but there has been no widespread adoption of the method in this country by users of conventional steel. This may be partly explained by the fact that until recently no American manufacturer produced this equipment and operators have been obliged to build their own hot-millers or import them. Several years ago a few machines were built in Seattle, Wash-ington, and operated in some mines in the northwest, but, for reasons not generally known, the effort was abandoned.

Jan 1, 1940

By W. W. Odell

ONCE it was believed that anthracite or coke were the only fuels generally available and suitable for the generation of water gas, particularly so when this gas was made in the generators of standard carburetted water-gas sets such as are commonly used in the manufacture of city gas. During the past 8 years, practice has changed considerably and it is -now common to find gas plants operating without anthracite or coke and using bituminous coal in the generator. This change in fuel has appreciably increased the marketability and sales of certain coal producers' products; accordingly it is of interest to coal operators and others to know the reason for this change, the present trend in practice and the adaptability of various coals for generation of water gas. This paper briefly discusses these conditions and some of the factors relating thereto. BITUMINOUS COAL NOT IDEAL BUT CHEAPER THAN COKE In spite of many changes which have been made in both process and generating apparatus for using bituminous coal as generator fuel more efficiently, in general it is not an ideal fuel for this purpose. It is supplanting coke because it costs less; it is so much cheaper per ton delivered at the gas works that water gas made therefrom costs less per unit-volume than that made from coke, even though the quantity of generator fuel consumed per therm (100,000 B. t. u.) of gas made is greater with coal. This is the reason why so many city gas plants, as well as others, are using bituminous coal instead of coke.

Jan 1, 1927

By G. W. Traer

THE distillation of bituminous coals at what is commonly termed low temperature, and the quantities, nature and adaptabilities of the products have been the subject of considerable experimentation, during recent years. Fortunately, the earlier work in this country was done by men whose scientific training qualified them properly to record and interpret the results of-their experiments. The work of Prof. Parr, of the University of Illinois, is especially notable in this respect. Prof. Parr's work, added to that of English experimenters, demonstrated certain things to a degree which is generally regarded as convincing. They have proved that a caking bituminous coal, when subjected to a temperature of not more than 1000° F. (preferably somewhat less) will yield light tar having low specific gravity (about 1.06) and high value; also, that this yield, with a given coal, will depend upon the percentage of hydrocarbons in the coal, the maximum temperature used, and the promptness with which the distillate gases are removed. It is assumed that air is excluded from the retort, and that the coal is subjected to heat for a sufficient time to drive off all of the tarry hydrocarbons. The results attained in the first, or low-temperature stage of the Carbocoal process, recently described by C. T. Malcolmson, corroborate these general principles. It is the purpose of the writer to describe other work of a practical nature, directed toward the commercial adaptation of these principles, which was begun nearly two years ago; this investigation was assisted by A. J. Sayers, of the Link-Belt Co., and Carl Scholz.

Jan 9, 1918

By Benjamin Moore

AT present the demands of the United States for strontium are met by imports from Germany, England and Canada, which vary considerably in proportions of ore and finished salts, in tonnage and in value. Statistics for the period 1926-1932 are given in Table 1. Domestic deposits are TABLE 1.-Strontium Imported into the United States, 1926-1932° Ore Chemicals Year Short Tons Value Pounds Value 1926 2,200 $58,159 5,433,044 $115,436 1927 1,356 58,711 4,233,816 149,383 1928 759 31,157 3,380,464 136,561 1929 973 45,505 4,578,327 196,233 1930 220 10,459 2,153,788 104,807 1931 (260 lbs.) 123 1,742,714 83,564 1932 5 276 469,481 20,910 a Mineral Industry (1934) 42, 61. known in many states, but the larger and purer ones are in the West, particularly in the desert region of southeastern California and western Arizona. These deposits are large enough to command interest, par-ticularly in consideration of future cheap power at the Boulder Dam. The deposits described in this paper were examined during an investi¬gation of the, mineral resources of the Boulder Dam region by the United States Geological Survey for the United States Bureau of Reclamation' in the spring of 1934. Mr. D. F. Hewett, who had general charge of the investigation, Mr. W. T. Schaller and Mr. M. I. Goldman contributed many helpful suggestions. Mr. N. H. Harshman assisted efficiently during the field work.

Jan 1, 1935

The Institute assembled in the library of the Sheffield Scientific School at 8 o'clock, Tuesday evening, February 23d. Prof. G. J. Brush greeted the members present on behalf of the Government of the Sheffield School in a few words of cordial welcome, to which President Raymond responded. Dr. Raymond then delivered an address on the History of the Relative Values of Gold and Silver. The Council presented, through the President, a list of names of persons duly proposed for members and associates, with recommendation for election. The following gentlemen were unanimously elected: *Prof. George J. Brush,. .. New Haven, Conn. *Prof. Oscar D. Allen,. .. New Haven, Conn. *C. Constable,.....New York City. *Leven S Goodrich,.... Oxmoor, Jefferson Co., Ala. *Charles J. Nourse,.... Columbia, Lancaster Co., Pa. *J. W. Mickley,.....Hockendauqua, Pa. *Hugh Alex. Crawford,. ..St. Louis, No. *General Ario Pardee,. .. Hazleton, Luzerne Co., Pa. N. W. Lord,.....New Pork City. J. Holme Maghee,.... New York City. *George E. B. Jackson,. .. Portland, Me. *Charles W. Watkis,.... Salt Lake City, Utah. *Charles E. Hall,....Philadelphia. *Charles J. Duval,.... San Francisco, Cal. Joseph Gorlinski,.... Salt Lake City, Utah. * Alfred Wartenweiler,. .. Salt Lake City, Utah. Wilmot J. Bowen,.... Salt Lake City, Utah. *Joseph Stokes,..... Trenton, N. J. Jason P. Brown,.... Boston, Mass. *William Davis Hartshorne,. . Bethlehem, Hunterdon Co., N. J. *Henry Williams,.... Spanish Bar, Clear Creek Co., Cot. *Robert Forsyth ,....Chicago, Ill. *S. T. Wellman,.....Cleveland, Ohio. *H. C. Walton,.....Chicago, 111. *Andrew Roy,.....Columbus, Ohio. *James H. Rittenhonse,. .. Providence, Pa.

By C. L. Warwick, A. B. Parsons

The papers and discussion appearing in this volume were presented at a symposium jointly sponsored by the American Society for Testing Materials and the American Institute of Mining and Metallurgical Engineers and held at Philadelphia, Pa., November 29, 30, and December 1, 1944. Late in January, 1944, Lieut. Col. C. H. Greenall, Officer-in-Charge of the Laboratory Division, Frankford Arsenal, Ordnance Department, U.S.A., suggested to the American Society for Testing Materials that it might be a propitious time to arrange for a symposium on stress-corrosion cracking at the Annual Meeting of the Society in June, and agreed to make available a number of papers relating to work being carried out at that Arsenal. The Society's Committee B-5 on Copper and Copper Alloys, Cast and Wrought expressed keen interest in the symposium, and other Society committees were contacted and agreed to cooperate. Since the subject is one of primary interest also to the American Institute of Mining and Metallurgical Engineers, it was arranged that the two organizations would jointly sponsor the symposium. A Symposium Committee was formed under the joint leadership, for A.S.T.M., of Carter S. Cole, then Chief of the Metals Branch, Conservation Division, War Production Board and now Engineer on the Headquarters Staff of the Society; and, for A.I.M.E., of E. A. Anderson, Chief of Metals Section, Research Division, New Jersey Zinc Co. (of Pa.) and chairman of the Program Committee of the Institute of Metals Division. The Symposium Committee was constituted as follows:

Jan 1, 1945

Soil Testing for Engineers. By T. W. Lambe. Published by John Wiley & Sons. 165 P. $5.00.-Filling a need for a text for the teaching of soil testing in the laboratory, this book is also of value as a reference for practicing engineers and for personnel in soil laboratories. Following an introductory chapter on general laboratory procedures are chapters devoted to the individual laboratory soil tests which are commonly employed. Apparatus, supplies, recommended procedures, discussion of procedure, calculations results, and numerical examples are provided for each test. Brief derivations of formulas and explanations and discussions of calibration procedures and special techniques are given in the appendix. Mesabi Pioneer. Copyrighted 1951 by the Minnesota Historical Society.- Publication of this book has been made possible by a generous gift to Society from the E. J. Longyear Co. of Minneapolis. This book covers the evolution of the Mesabi Range from a wilderness into the nation's greatest iron producing area. In this book is found the first hand experiences of Edmund J. Longyear who saw the development of the range from its beginnings, and who himself took a notable part in it. In 1890 Edmund J. Longyear sank the first diamond drill hole on the Mesabi. During the next two decades he sank pits and holes- 7133 of them-throughout the length and breadth of the Mesabi Range, exploring for iron ore. He saw roads and railroads built. He watched the range communities--Hibbing, Chisholm, Biwabik, Mountain Iron and the others change from exploration camps to

Jan 11, 1951