Search Documents

By Paul A. Farrar, Harold Margolin

The Ti-Al-V system has been delineated from 50 to 100 wt pct Ti and front 600 to 1400°C by X-ray and ntetallographic techniques. Isothermal sections were delineated at 600, 700, 800, 900, 1000, 1100, 1200, 1300, and 1400°C. X-ray and metallographic evidence indicated the presence of two phases and in addition to those reported by previous investigators of the ternary system'-3. T HE titanium-rich region of the Ti-Al-V system as originally proposed by Rausch et UZ, and Jordan and Duwez3 was based on the binary Ti-Al diagram as proposed by Bumps et uZ. As additional phases have been shown to exist5-' in the region previously thought to be all a, the titanium-rich region of the Ti-Al-V system is open to serious question. Therefore, in order to determine the effect of the indicated changes in the Binary Ti-Al system on the ternary Ti-Al-V system the present investigation was initiated. EXPERIMENTAL PROCEDURE The experimental procedures in this investigation are the standard techniques used in the study of titanium-alloy systems which have been described in detail previously.1° Consequently, only details pertinent to the present work are discussed. The alloys employed for the delineation of this system were prepared from titanium obtained from the Bureau of Mines (73 BHN) 99.99 pct Al and 99.7 pct V, by the consumable arc-melting technique. The titanium was premelted into buttons of 25 g because spattering during the first melt caused uncontrollable loss of alloying constituents. Typical analyses of the material used have been reported elsewhere Attempts to hot roll the alloys prior to heat treatment were made on the first series of alloys prepared, but as the area of extensive hot workability was fairly restricted, see Table I, this practice was discontinued. The times of isothermal annealing are given in Table 11. A preliminary heat treatment of 96 hr at 1000°C was used prior to heat treatment at lower temperatures. The standard techniques used for polishing specimens involved belt-grinding, grinding on emery paper, polishing electrolytically, and etching with Remington "A" etch. In the low-alloy region it was found that the oRo etch, developed by Ence and Margolin,o gave better contrast between phases. Where this procedure did not differentiate between phases clearly, the method of stain etching developed by Ence and was used. It has been previously reported15 that filing of titanium alloys is not desirable for producing X-ray powders, since the powder becomes contaminated by the file material. Therefore, for those samples not brittle enough to Crush, the procedure described below was used. The specimen was wrapped in molybdenum sheet and placed in a vacuum system and evacuated to 0.03 p. Palladium-pur if ied hydrogen was then admitted to the system until a partial pressure of 5o Cm of H was reached. The specimen was heated in the system to the temperature of original heat treatment and was slowly cooled over a period of 3 hr to 400°C while the partial pressure of hydrogen was maintained. The sample was removed from the system after it had completely cooled and was crushed to a powder of 230 to 270 mesh. The powder, wrapped in molybdenum sheet, was dehydrogenated at the temperature of original heat treatment until a partial pressure of 0.03 p was maintained in the system for at least 1/2 hr. The tube containing the powders was quenched in iced brine while still connected to the vacuum system. After dehydrogenation, the powder, except for the

Jan 1, 1962

By F. D. Patchen

Changes in the properties of partland cement upon the addition of fine-ground silica are discussed. Data were collected from formulations cured for periods up to 60 days at temperatures varying from 180" to 350°F. Compressive strengths, permeabilities and thickening times are compared. It is demonstrated that addition of find-ground silica in proper proportion results in a hydrated cement with superior properties above 230°F; i.e., early compressive strengths are higher and increase with additional curing, permeabilities are significantly lnrver and thickening times are increased. X-ray analysis of hydrated cement samples have been used to determine more fully the complex chemistry of these systems. Dicalcium silicate alpha-hydrate was found in all neat cements cured above 260°F. A 10 weight per cent silica addition produced a maximum amount of this phase. Xonotlite and tobermorite have been identified as hydration products at 320°F in systems containing 35 or more weight per cent silica. Formation of these components appears to be primarily responsible for the gain in strength and reduction of permeability observed after the addition of silica. INTRODUCTION For several years it has been recognized that loss of compressive strength occurs when portland cement is cured at a temperature above 250°F. This phenomenon has been called "strength retrogression". More recently it has been recognized that increased permeability usually is associated with decreased compressive strength at these temperatures. At curing temperatures above 300°F, these factors reach serious proportions. A compressive strength loss of 50 per cent between curing times of 24 hours and 14 days has been reported,' and permeabilities as high as 10 md have been measured in neat cements cured at 320°F for seven days.' Earlier investigators,' although unsuccessful in eliminating strength retrogression, stated ". . . .it appears possible that by the proper selection of additives for cement, strength loss with age at high temperatures can be either eliminated or considerably lessened". One solution suggested was the use of a pozzolanic material, hydrated lime, and a retarder. Menze15 in 1934 discovered that portland cement containing finely divided silica possessed high compressive strengths when the curing temperature was 350°F. The use of such a composition is now an established practice in the manufacture of steam-cured cement blocks. It is reasonable to assume that the same beneficial effect can be used advantageously in high-temperature oilwell cementing operations. Ludwig first mentioned the use of sand for this purpose. Later, a portland cement containing moderate additions of silica flour and retarded with CMHEC, a cellulose derivative. was recommended for high-temperature application." These formulations have been successfully employed in the field."'" This paper presents the results of a research program to test the efficacy of finely ground silica in increasing the compressive strength and reducing the permeability of oilwell cement compositions containing portland cement. Included also are X-ray diffraction patterns of powdered samples which have been used to determine some of the important chemical reactions occurring in these systems. LABORATORY PROCEDURES AND MATERIALS All compressive-strength test specimens were prepared and cured from a slurry in accordance with API RP 10B, with two modifications. A final curing pressure of 5,000 psi was maintained for a one- or three-day period; but, for further curing, pressures were reduced to the vapor pressure of water at the curing temperature. Also, the water content was varied in samples containing silica to maintain the slurry viscosity within a range of 5 to 15 poise as measured on a consistometer. Test specimens at 180°T were cured in a water bath at atmospheric pressure. At higher temperatures the specimens were cured in a steam-jacketed high-pressure curing vessel at 5,000 psi for a one- or three-day period. cubes cured for longer periods were removed from the pressure-curing vessel after 24 hours, sealed in small bombs containing water and placed in an aging oven.

By Herbert H. Kellogg

DEPOSITS of high-silica kaolinite clays occur at many places in central Pennsylvania. These white clays were formed apparently by weathering of argillaceous quartzite and limestone. Their geology, distribution and use have been reported by Leighton.1 The larger deposits have been mined from time to time, and the clay, after washing to remove coarse sand, has found use as rubber filler, foundry clay, and in white cements. In general, the clay from these deposits contains too much grit (quartz) to be useful as paper filler, and the silica content is too high to make it useful as china clay for ceramic ware. Gravity methods for the separation of quartz from these clays have failed because of the extremely fine size of the quartz grains, but by the methods of froth flotation described in this paper these sandy kaolins can be made to yield a purified kaolinite that has a chemical composition close to that of good-grade Georgia kaolins, and is free enough from grit to be used as a paper filler. As by-products of the separation, a fine (-325-mesh) sand assaying 95.5 per cent Si02, and a very fine (-3-micron) clay are produced. The possible ceramic uses of these products are being investigated at The Pennsylvania State College. EXPERIMENTAL PROCEDURE The Sample.-The clay sample used in these tests was obtained from a small mine near Tyrone, Pa. It had already been washed to remove coarse sand, and represented the finished product of this small mine and washery. Microscopic examination showed that the clay was composed almost entirely of the minerals quartz and kaolinite, and that the quartz was present mostly in particles larger than one micron, while the kaolinite particles generally were less than 20 microns in size. The kaolinite and quartz particles were physically separable by blunging the clay in water with a suitable dispersant. Preparation of Flotation Feed.-By the addition of NaOH in an amount equal to 3 lb. per ton of solids, the clay was completely dispersed in water. Flotation feed was prepared by allowing a dispersed suspension (10 per cent solids) of the clay to stand for the period of time required for a 2.5-micron particle of quartz to settle from the top of the container to the bottom. After this settling period the suspension was decanted from the settled solids. The settled solids were redispersed in water and the separation was repeated once. The two fine fractions were then combined. Thus the clay was divided into a fine and a coarse fraction by size separation at approximately 2.5 microns.* The fine fraction was found to have a considerably lower sand content than the raw clay (Table I), and was not treated further. The coarse fraction formed the flotation feed for all the tests described in this paper.

Jan 1, 1945

By J. R. Dawson, A. B. Kinzel

THE purpose of testing is to determine whether the material in question is identical in all essential respects with similar material which has given satisfactory service. The most common method of securing such information is to select samples as representative of the entire material and subject them to destructive tests. As the welding industry grew, service data were accumulated and tests of welds took on new significance. New tests were devised and old tests modified so as to be more pertinent to welding. Moreover, in some cases the generally accepted procedure of testing by sampling is not accorded the same degree of confidence when applied to welds as in the usual applications. Thus, in instances where great hazard would be involved should the material fail, means of non-destructive testing have been sought with favorable results. Accordingly, tests used today may be divided into two groups, destructive and non-destructive tests.

Jan 1, 1930

By Henry R. Piehler

Continuous seven- and nine teen -filament close-packed silver-steel filamentary composites mere tested in tension. For purposes of comparison, the tensile behavior of the composite was predicted from the measured properties of the individual com-ponents. It was assumed that the axial strain is the same in both components and that the contribution of each component to the composite flow stress is proportional to its volume fraction. Good agreetnent was obtained between the observed and predicted tensile behavior. However, the composite elongation at fracture was about twice that observed when the individual steel wires were tested alone. Composites in which the filaments were widely spaced failed by the consecutive fracture of the filaments. In composites with closely spaced filaments, a composite instability preceded frachcre. These effects are explained in terms of a lateral restraint to the necking of the filaments which develops in the deforming composite. TWO-COMPONENT or composite materials are increasingly being developed and used as structural materials. Of all the composite geometries used, the filamentary configuration has proved to be the most successful. Polymer-bonded fiber-glas, the most common of the filamentary composites, has been investigated most extensively to date. One explanation of the behavior of fiberglas1 suggests that the load transfer between the glass fibers and the polymer matrix occurs primarily through friction. Bond separation between the fibers and the matrix is presumed to occur at very low stresses. Subsequently, only frictional bonding can provide for the transfer of load from the matrix to the fibers. The force normal to the fiber-matrix interface which gives rise to this friction is assumed to arise from the matrix shrinkage which occurs during solidification. The behavior of metallic filamentary-composite materials would be expected to differ from that of fiberglas in several significant aspects. Residual stresses resulting from differences in thermal contraction can be kept to a minimum by proper heat treatment. A strong wetted bond is formed between the two phases. In brazed joints,2 for example, the interphase bond is sufficiently strong that the weaker material will fail before separation occurs at the interface. Most metal filaments can undergo appreciable amounts of plastic deformation before failure. Failure by plastic instability or necking frequently occurs in metallic filaments, but not in glass fibers tested at room temperature. Differences between the behavior of fiberglas-polymer and metallic filamentary composites have indeed been observed in composites containing various types of metallic filaments in a silver matrix.3,4 At strains of the order of 10-2 pct, all the deformation was accommodated by the silver matrix. Hence, the strength of the composite depended only on the fiber concentration and not on the nature of the fiber. At higher strains, the strength of the composite increased when filaments with higher work-hardening rates were used. Surface slip line observations on a silver-mild steel composite that had been stretched 4 pct showed that an appreciable amount of deformation occurred in the filaments. Work on tungsten-copper filamentary composites5 has shown that the ultimate tensile strength for varying filament fractions followed a linear mixture rule. Assuming that the axial strains in both filaments and the matrix are equal, this linear mixture rule can be expressed as: The subscripts c, f, and m refer to the composite, filaments, and matrix, respectively. A and V are the area and volume fractions of each component. sc and of are the ultimate tensile strengths of the composite and the filaments. sm is the flow stress of matrix at a strain equal to the elongation at failure of the filaments. However, the tungsten filaments can undergo only a limited elongation before they fracture without an appreciable reduction in area. A composite containing more ductile filaments might indeed deviate from this linear mixture rule for the ultimate tensile strength, since filament failure by necking might be arrested by the matrix. SPECIMEN PREPARATION Specimens were prepared from 0.8 pct carbon steel piano wires of 0.015 in. initial diameter. The wires were given a thin nickel flash and a silver plate varying in thickness from 0.015 to 0.007 in., depending on the filament fraction desired. In order

Jan 1, 1965

By T. S. Lundy, R. E. Pawel, F. R. Winslow, C. J. McHargue

The volume-diffusion coefficients of Nb-95 and Ta-182 in niobium have been measured over the temperature range 878° to 2400°C. High-temperature specimens (T 21500°C) were sectioned by conventional lathe and grinding techniques while low-temperature specimens were sectioned by an anodizing and stripping technique previously described. Over a range of more than ten orders of magnitude in diffusivity, the self-diffusion data is well-represented by the equation: D = (1.1+ 0.2) exp [- (96,000 * 900)/RT ] cm2/sec Upward deviations from this line are explained by short-circuit diffusion in combination with the loss of resolution of the sectioning techniques. Oxygen contamination within the range 100 to 450 ppm was found to have little or no effect on the self-diffusivitj 01 niobium. In a limited number of measurements, the diffusivity of Ta-182 in niobium was found to be about half that of Nb-95 in niobium. These data may be described by D = (I.0+0.90.5)exp [- (99,300 * 2400) /RT ] PREVIOUSLY reported studies of self-diffusion in niobium were by Resnick and Castleman1 and Peart, Graham, and Tomlin.2 The data of Resnick and Castleman over a temperature range 1585" to 2120°C show considerable scatter but. can be represented by D = (12.4 *0.8) exp [-(105,000+3OOO)/RT] cm2/sec The limited data of Peart, Graham, and Tomlin follow the equation D = 1.3 exp (-95,00O/RT) cm2/sec In view of recent diffusion data for ß zirconium3 and 0 titanium4 in which Arrhenius-type plots do not yield straight lines and of the potential high- temperature uses of niobium and its alloys, we thought it important to investigate the diffusion behavior of this bcc refractory metal over a large temperature range. This has recently been done for molybdenum,5 chromium,6 vanadium,"" and tantalum.9 Niobium was a particularly suitable material for this study largely because of the development of an anodizing and stripping sectioning technique which enables diffusivities as small as l0-19' sq cm per sec to be determined accurately.10 In addition to self-diffusion data, data were obtained for the diffusion of Ta-182 in niobium and for the effect of varying oxygen content on self-diffusion. I) EXPERIMENTAL PROCEDURE Materials. The niobium was obtained from three sources: 1) melting stock from Shieldalloy Corp., 2) electron-beam melted single crystals, 1/2 in. diameter, from Semi-Elements, Inc., and 3) oxygen-doped, electron-beam melted single crystals from Materials Research Corp. The melting stock was electron-beam melted and specimens 5/8 in. diameter by 1/2 in. long were machined from the center of the bar. The analysis supplied by the vendor and an interstitial analysis of one of the specimens are given in Table I. The single crystals (type 2 above) were cut with a jeweler's saw to specimens about 3/8 in. long. The interstitial analysis of this material is given in Table 11. This material was used

Jan 1, 1965

By W. A. Eardley

FIFTEEN years ago the world's deepest oil well penetrated the earth about 7300 ft. That depth has now been more than doubled. Why has such deep drilling become necessary and how has it become possible? Three factors have had an important bearing: (1) Depletion of shallow zones, making it necessary to search for deeper producing measures. (2) The perfection of prospecting methods, which have been success- fully used to locate favorable buried structures, many at great depth. (3) Improvement in the quality of steels used for drilling.

Jan 1, 1940

By F. O. Garrabrant

Power is furnished to the Climax Molybdenum Co. by the Public Service Co. of Colorado over two 100,000-volt lines to a bank of three 3333-kva. transformers 100/13.8 kv. These transformers are so designed that with the addition of forced cooling their capacity may be increased 331/3 Per cent at 12,000-ft. altitude. Under present conditions, these transformers are operated at 140 per cent of their rating with forced air cooling. On the secondary side of this bank there is a 15-kv., 1200-amp. Westinghouse oil circuit breaker provided with automatic reclosing relays allowing three successive short circuits before lockout. From this breaker 13.8-kv. power is transmitted to a central switching station (Fig. I) where all circuits radiate to the different operations of the property. Each circuit is protected by a 23-kv., 600-amp. oil circuit breaker with by-pass and isolating disconnecting switches.

Jan 1, 1947

By Ta M. Li

How do you convert a copper-zinc resource into a viable economic mining operation? This problem, unlike most, was complicated by the additional presence of a sub-arctic climate, highest labor costs in the world, low-grade copper-zinc values, depressed market prices, and a complex mineralization.

Jan 12, 1977

By Albert Sauveur

Jan 1, 1924

By Albert Sauveur

Jan 1, 1924

By H. Majima, E. Peters

The oxidation rates of pyrite, pyrrhotite, chalcopy-rite, chalcocite, covellite, bortzite, galem, sphalerite, and stibnite have beet2 carefully compared at 120 oC, using aqueous phosphate solutions buffered at pH 2.7, 7.1, and 11.2 as zvell as in 1.0 M NaOH and in am~onia-containing solutions. Under conditions of these studies, variations in rates of more than a factor of two per unit of mineral surface area were not observed for different minerals in phosphate buffered solutions, except that pyrrhotite showed unusually rapid oxidation rates In acid solutions, and stibnite showed very rapid oxidation rates in basic solutions. In caustic solutions, oxidation vates varied considerably, the most rapid being for pyrite and the slowest for sphalerite. In the presence of ammonia, only copper minerals showed more vapid oxidation rates in neutral solutions. Oxidation rates were measured on the basis of oxygen-consunzption rates per unit surface area of exposed mineral, using equivalent surface areas, mineral mesh sizes, pulp densities, agitation, and oxygen pressure. OXIDIZING pressure leaching of sulfide minerals has been a commercial method of treating concentrates of nickel, cobalt, and copper for over a decade, and recently the treatment of lead and zinc concentrates,' and even the recovery of sulfur from pyrrhotite by such processes, have been shown to be technically feasible.' Furthermore, the leaching of uranium ores by solutions acidified through the oxidation of pyrite and other sulfides present in the ore is commercially practicable.3 5 The mechanisms by which sulfide minerals oxidize in aqueous environments are not yet understood. However, certain generalities can be made for systems containing no unusual reagents, in which oxygen is the oxidizing agent. In acid solutions the oxidation of many sulfide minerals leads to the formation of elemental sulfur.8'7 The attack of some sulfides, notably galena (PbS), sphalerite (ZnS), and pyrrhotite (FeS), at temperatures below about 110°C leads to an almost quantitative conversion of the sulfide mineral to elemental sulfur according to the equation: On the other hand pyrite (FeS2) and copper minerals do not yield elemental sulfur quantitatively. Not more than 50 pct of the sulfur in pyrite is converted to the elemental form in acid oxidation, and this percentage is lowered by higher temperatures and possibly higher oxygen pressures.8'9 Copper minerals sometimes yield elemental sulfurlo'" but, since sulfur can reduce cupric ions with the precipitation of CuS or Cu2S, it is not likely that elemental sulfur is obtained in good yield. In acid solutions sulfur that is not converted to the elemental form always appears as sulfate salts or sulfuric acid. Sulfide minerals that yield elemental sulfur nearly quantitatively on oxidation in acid solutions tend to generate H2S when the conditions are not oxidizing. However, although it has been suggested that H2S is an essential intermediate in the mechanism of oxidation," this is doubtful because it is oxidized very slowly by oxygen. In basic solutions elemental sulfur is never formed, as predicted by thermodynamical considerations, summarized in the form of a potential-pH diagram in Fig. 1. However in neutral and basic solutions, unstable forms of sulfur not shown in the diagram appear during oxidation, notably thiosulfate (SOT-) and polythi-onates (S,O;-, x = 2 to 6).l3,l4 On prolonged oxidation only hexavalent sulfur as sulfate (SOi-) or sulfamate (NHzSO;) is found to remain, the latter appearing only in the presence of ammonia. The oxidation kinetics for thiosulfate by oxygen are the subject of a separate paper,'5 and were studied on the presumption that thiosulfate may, in fact, be a primary oxidation product for sulfide minerals, at least in neutral and basic solutions. A survey of the literature indicated that comparative oxidation rates for different sulfide minerals were needed to establish the role of the mineral structure and its thermodynamic properties on the oxidation rates and mechanisms.

Jan 1, 1967

By F. B. Plummer

PERHAPS the greatest progress made in the technical methods of oil production during the last year has been in handling gas from the new fields that yield light distillate fractions. At least sixteen recycling plants have been perfected and installed in South Texas fields alone during 1939 having a daily capacity of more than one billion -2 cubic feet of gas and capable of producing more than a million gallons of distillate daily. The process consists of running the gas under pres- sure through especially designed plants, separating out the condensate, then compressing the gas to 3000 lb. or more, depending on the subsurface pressure in the formation, and injecting gas back into the reservoir to be produced again later, along with more of the liquid hydrocarbons, and again recycled. Hence production in these distillate fields in sense has changed from that of producing a constantly diminishing and much-wasted product to a more or less continuous manufacturing process, in which practically all the gas is conserved-a real triumph in engineering practice.

Jan 1, 1940

John S. Kennedy, Chamhersburg, Pa. (communication to the Secretary): The washing-plant described by Mr. Johnson is a good illustration of the advantages derived from a well-designed and care-

Jan 1, 1895

By R. I. Jaffee, J. G. Dunleavy, W. Hodge, H. R. Ogden

Jan 1, 1949

By WALTER M. DAKE

GENERALY speaking, the bituminous coal mines of the country are being operated at a loss. To purchasers of the necessary commodity, a statement of this character may have the sound of a far fetched propagandist cry; but to the coal producer who lives in the hope of an up-turn in the almost stationary market price of his product, while inking in red his monthly operating balances, it carries the ringing sound of truth.

Jan 1, 1925

By J. Chipman, H. R. Larson

The data previously reported for the quantity as a function of oxygen pressure at 1550°C have been used to compute the activities of Fe, FeO, Fe2O3, and COO in slags of the ternary system. Activities of the first three have been obtained also for two quasi-ternaries involving fixed CaO:SiO2 ratios. IN a previous paper1' the authors reported the results of an investigation into the effects of oxygen pressure on the composition of various simple slags analogous to some of those which are found in steel-making practice. The ratio of ferric iron to total iron was studied at 1550°C in iron oxide melts to which lime, magnesia, lime-plus-silica, and other oxides were added. The oxygen pressures involved those of air, carbon dioxide, and carbon dioxide plus carbon monoxide in several proportions. Although very low oxygen pressures could not be used, the slag-metal equilibrium studies of Fetters and Chip-man' permitted extending the results to slags in equilibrium with iron. For the ternary system CaO-FeO-Fe,O, the oxygen pressure-composition relationship has been determined from zero percent lime to lime saturation over an oxygen pressure range from air to that represented by equilibrium with liquid iron. Lime and silica were added to iron oxide in the ratios 0.54, 1.306, and 2.235 to form three quasi-ternary systems which were also studied over the entire region of liquid melts at 1550°C. Ternary Gibbs-Duhem Equation Wagner" has developed a method by which the activities of two components of a ternary system can be calculated if' the activity of the third component is known throughout the composition range being considered. The fundamental form of the Gibbs-Duhem equation for ternary systems is N, d In a, + N2 d In a, + N3 d In a3 — 0. Wagner has developed a usable form of this equation by introducing the term y = N3/(N3 + N1) and rearranging the equation to give (? In a1/?N2)x = -y/(1-N2)2 (? In a2/?y) x2 N2/1-N2 (? In a2/?N2) y To apply this equation to the slag system CaO-FeO-Fe,O,, the activity of one of these components must be known. However, the only activity which is known from the experimental data is the activity or pressure of oxygen in the gas phase with which the slag is in equilibrium. The activity of oxygen in the slag can be defined as the square root of the oxygen pressure. In order to use oxygen as one component, the composition of the slags must be converted to the basis Fe-O-CaO. Oxygen, exclu-sive of that contained in CaO, then becomes com-ponent 2 in Eq. 1, Fe is selected as 1 and CaO as 3. Then y = Ncao/(Ncao + NFe). Eq. 1 then becomes (? In a fe/? Nx) y = -y/(1-No)2 (? In ao/?y) xp - No/ 1- No (? In ao/ O No) y. In order to evaluate Eq. 2, the boundary conditions must be known. The obvious choice of a standard state for iron is to assign slags in equilibrium with iron an activity of one. Then In a,., or log aFe, which is substituted for convenience, is determined by integrating along a line of constant y from the slag in equilibrium with iron to the composition at which log a,, is to be determined. Mathematically this can be expressed as log aFe (Nlog y) = log a'Fe + (? log a Fe/? No) dNo where the primes indicate equilibrium with liquid iron and a'Fe = 1. When Eq. 3 is integrated along a line of constant y, the following is obtained: log a Fe (No, y) = - y No ?/ No ? y ( log ao/(1- No)2) No d No - No/1-No d log ao. Lime-Iron Oxide Slags Iron Activity: The oxygen pressure of lime-iron oxide slags is shown in Fig. 1 as a function of j, de-fined as j = Fe+++/(Fe++ + Fe +++) for various constant mol percentages of lime. The j values at 0 to 60 pct lime were then determined for oxygen pressures of 1, 10-1, etc. to 10-" atm. For purposes of calculation, the line for zero percent lime was extrapolated to

Jan 1, 1955

By P. R. Sperry, P. A. Beck, J. Towers

Dahl and Pawlek1 found that electrolytic copper develops extremely coarse grains at 1000°C after about 90 pct reduction by rolling. This coarsening occurs only under conditions of penultimate grain size, deformation, and alloying which lead to the "cube" recrystallization texture.l,2,3,5 The peculiar angular shapes and straight grain boundaries of the coarse grains were noted by several investigator.1,4,5 On the other hand, coarsening in Fe-containing aluminum or in AI-Mn alloys8 does not depend on a "cube" (or any well developed) recrystallization texture. It is true that increasing deformation by rolling, and, therefore, an increasingly well developed re-crystallization texture, are associated with decreasing incubation periods of coarsening.6-7-8 Nevertheless, coarsening readily develops in aluminum even after only 30 pct reduction by rolling, where the recrystallization texture is very weak.6,8 Also, coarsening was observed by Jeffries9 many years ago in sintered thoriated tungsten, which presumably has no preferred orientation. In all these cases coarsening is associated with grain growth inhibition by a dispersed second phase.8,9 The annealing temperature has to be suficiently high to overcome the inhibition at a few locations. But if it is too high, growth starts at many points, and the resulting grain size becomes much smaller.9 Normally, the coarse grains are more or less equiaxed, and the boundaries have a typical ragged appearance.6.8 Cook and Macquarie4 demonstrated that, in addition to the texture-dependent coarsening previously found at 1000°C,l electrolytic tough pitch copper may also coarsen at 800°C after 50 pct reduction by cross rolling. The coarse grains formed under such conditions have rounded shapes and ragged boundaries, like those in aluminum. When the annealing temperature is higher, the tendency for their formation decreases. All these observations suggest that the coarsening at 800°C is associated with inhibition by a second phase. Actually, coarsening at 800°C after 50 pct reduction by cross rolling was observed only in tough pitch copper,4 which contains Cu2O particles. On the other hand, the texture-dependent 1000°C coarsening occurs in both tough pitch and oxygen-free copper;4 it does not appear to depend on the presence of a dispersed second phase. However, the interpretation of the 800°C coarsening in Cu after 50 pct rolling as an inhibition-dependent process, similar to the coarsening in A1-Mn alloys, is somewhat weakened by the fact that this coarsening was reported4 to occur only after cross rolling, and not after straight rolling. It was, therefore, decided to re-examine this question. A 1 in. diam electrolytic tough pitch copper rod, No. 2 hard drawn, was annealed for 20 min at 700°C, rolled to 0.5 in., annealed 10 min at 700°C, and straight rolled to 0.064 in. It was then given a penultimate anneal of 20 min at 500°C and it was cut into four sections, which were given final reductions by straight rolling as follows: A 30 pct reduction of area B 50 pct reduction of area C 70 pct reduction of area D 90 pct reduction of area Specimens cut from the four sections were finally annealed at 800°C in an oxidizing atmosphere. Strip A remained fine grained up to 10 hr, but the specimen annealed 12 hr consisted of only 2 large grains. Strip B had a few scattered large (1/2 to 3/4 mm) grains after 1 min, although the balance of the specimen consisted of fine grains of about 0.02 mm. After 5 min there were several 10 to 15 mm grains present, and after 1 hr strip B was completely coarsened. The coarse grains had the same characteristics (see Fig 1) as those obtained by Cook and Macquarie at 800°C after cross rolling. Strip C had several grains of 0.05 to 1 mm after 1 min, but it was still largely fine grained after 12 hr. After 48 hr it consisted entirely of grains of about 0.5 to 4 mm, with an extraordinarily large number of twin bands. Strip D remained com- pletely fine grained after 4 hr at 800°C. These results indicate that, in the deformation range of 30 to 70 pct reduction, the incubation period for coarsening as well as the rate of growth and the final size of the coarse grains decreases with increasing deformation. Similar

Jan 1, 1950

By F. William Bloecher, William B. Plank

CURRENTLY 12,892 students are enrolled in the mineral engineering schools of the United States and Canada, marking an all-time record high for these schools. It shows a remarkably rapid recovery from the effects of World War II. Enrollment in all the other engineering branches has also increased but not so rapidly as in the mineral engineering branch. Almost all the data in this report are from the eighth questionnaire study of the mineral engineering schools made, as formerly, under the auspices of the Mineral Industry Education Division of the AIME. Every school is represented in the data, for which the authors thank the deans and professors who supplied the information. For this reason, the data of all the studies are comparable, an achievement not always possible in endeavors of this kind. For comparison with the general engineering enrollment situation, data are included from the January 1947 issue of the Journal of Engineering Education.

Jan 1, 1947

Jan 4, 1951