Search Documents

By J. R. Long, T. R. Graham

This report is concerned with part of a series of investigations carried on by the Federal Bureau of Mines on alloys, particularly nonferrous alloys, made with electrolytic manganese. A broad general program instituted after commercial quantities of electrolytic manganese became available was necessary in order to compare the effects of electrolytic manganese with those of the ordinary commercial grades. Representative analyses of these two materials show the commercial manganese metal to contain up to 2 per cent iron, a maximum of I per cent silicon and 0.06 per cent carbon, while the electrolytic manganese rarely exceeds 0.01 iron, 0.02 sulphur, with no silicon or aluminum. In the literature, the emphasis has been largely on high-strength casting alloys containing up to 5 per cent manganese, and few data are available on wrought manganese alloys. These factors, coupled with the strategic position of copper and zinc, have given impetus to the Bureau's War Research Program for the development of alloys containing nonstrategic manganese for the purpose of supplementing or providing alternates for the more strategic metals. The alloy reported here was studied, along with several other ferrous and nonferrous alloys, as possible cartridge-case material, and was chosen after a review of the properties of the ternary alloys of copper-manganese-zinc. Preliminary Work In a cursory survey of this system, alloys ranging from 60 to 95 per cent copper, o to 50 per cent manganese, and 5 to 40 per cent zinc were investigated. The alloys containing 60 per cent copper were found to fall into the two-phase alpha plus beta region of the system, and since those containing 70 per cent would not permit a saving, only alloys containing 65 per cent copper were considered. The tensile properties of these 65 per cent alloys are plotted in Fig. I as a function of manganese content for annealed material and for four conditions of cold-work In the annealed condition the increases in strength and decreases in elongation are minor up to 15 per cent manganese; beyond this, the changes become more significant. In the cold-worked condition, the first 5 to 10 per cent of manganese appears to have the greatest strengthening effect, the rate of increase dropping off as the manganese increases beyond this amount. These effects are more pronounced with moderate than with severe cold reduction. It is also interesting to note that while the elongation of annealed material drops regularly with increasing manganese, the elongation in the cold-worked state is relatively little affected by increasing manganese content, particu-

Jan 1, 1944

By P. A. Fisher, J. B. Wilson, D. J. Whitehead, C. J. P. Ball, A. C. Jessup

The properties of a new magnesium alloy ZT1 containing 3.0 pct Th, 2.5 pct Zn, 0.7 pct Zr are described. The alloy possesses good creep and fatigue resistance up to 650°F, is free from microporosity, and is readily sand-cast. ZT1 is shown to be superior to zinc-free Mg-Th-Zr alloys. THE advent of the jet engine created a demand for a light sand-casting alloy capable of being cast into large complex shapes and capable of resisting creep at temperatures up to 500°F. This demand has been largely met by alloys of the magnesium-cerium mischmetal-zirconium types, containing about 3 pct Ce mischmetal and 0.7 pct Zr, typified by Elektron magnesium alloys MCZ and ZREI, the latter alloy also having a zinc addition of 2.5 pct. These alloys utilize the valuable properties at elevated temperatures conferred by the addition of rare earth metals to magnesium, a fact which has been known for many years and discussed by several investigators.1-1 Murphy and Payne8 showed that the addition of the powerful grain-refining element zirconium to Mg-Ce mischmetal alloys produced alloys with attractive room temperature properties combined with good creep properties and castability. With the increasing power of modern jet engines the temperatures to which some of the magnesium parts are subject are likely to exceed the safe working range of the cerium-mischmetal-containing alloys, and at the beginning of the research considerable interest had been shown by aeroplane engine designers in a magnesium sand-casting alloy suitable for service at higher temperatures, e.g., 600°F and above. At an early stage in the development of this type of alloy a check on the fatigue properties at elevated temperatures indicated that, since the fatigue limit even at 108 eversals was appreciably higher than any permissible creep stress, the main emphasis of the research could be concentrated on creep behavior. The primary aim in developing the new alloy has therefore been to attain maximum creep resistance; but due consideration has also been given to other important properties such as castability, tensile strength, and cost. It is by now well established that it is not possible to correlate creep strength with other short time mechanical properties such as are obtained in tensile

Jan 1, 1954

By H. S. Martin

ALTHOUGH it was known some years ago at the- Utah Copper Co. mills that fine grinding improved flotation recoveries, no accurate data were available until recently as to just how far the grinding could be carried economically. In 1923 the ultimate degree of fineness for flotation feed was supposed to be about 10 per cent. on 65 mesh, with approximately 55 per cent. through 200 mesh, which meant that most of the mineral would pass 100 mesh. At this time Garfield and Wilfley tables were used ahead of flotation and a good deal of the coarse mineral removed prior to the ball mill regrind. Shortly afterwards, mill-scale tests developed the fact that on a feed containing not over 10 per cent. +65¬mesh material flotation alone would give a copper recovery equal to that obtained by the combination of tables and flotation, but that on much coarser feed the recovery with flotation alone was lowered. This was at a time when all the sulfide minerals were floated if possible, so that the only requisite was to grind fine enough to free the mineral from gangue. EARLIEST USE op MICROSCOPIC EXAMINATION OF TAILINGS As early as 1921, the writer had attempted to determine by chemical analysis the relative proportions of copper minerals in tailings from an ore that made extremely poor flotation results. Chemical analysis was not satisfactory or conclusive, and samples of these tailings were sent to the U. S. Bureau of Mines Station at the University of Utah for micro-scopic examination. The question at that time was to determine, if possible, which copper minerals had been lost and why, but R. E. Head, in his report, revealed other interesting data. He said in part: Briefly stated, the mineral particles or grains may be classified into separate groups as follows: 1. Free grains of pyrite, chalcopyrite, chalcocite and bornite, respectively, which contain no other included sulfides; 2. Grains in which all three of the copper sulfides are represented (the core may he of chalcopyrite, partially altered to bornite, these two minerals being entirely surrounded by a shell of chalcocite); 3. Grains composed of equal amounts of bornite and chalcocite or chalcopyrite and chalcocite.

Jan 1, 1929

By J. J. Lander, L. H. Germer

Molybdenum and tungsten have desirable corrosion and temperature resistant properties, but the metals in bulk are expensive and their fabrication is difficult. Such considerations led to a search for a method of plating them upon base metals. This search was successful and led furthermore to a number of developments which could not have been foreseen. Neither pure tungsten nor pure molybdenum has been electroplated successfully, although the literature of electroplating is liberally sprinkled with the description of unsuccessful attempts. The process of plating these metals by thermal reduction of their halides has achieved onlv limited usefulness because of technical limitations and because of limited range of product quality. Plating by thermal decomposition of the carbonyls does not suffer from limitations of the same sort and the properties of the plate are readily controllable. This paper describes the plating of molybdenum and tungsten, and of compounds and alloys of these metals, by pyrolysis of their carbonyl vapors. Chromium also has been plated in this manner, but the experiments upon chromium have been less extensive and the results much less satisfactory. Probably the most important of the products which we have obtained are the alloys with carbon, and the carbides of the metals. Either molybdenum or tungsten can be deposited upon a base metal as a coherent and adherent coating. By adjusting the plating condition the carbon content of the coating can be made to have any value from substantially zero to about 35 atomic pct. The hardness is dependent primarily upon the amount of carbon in the plate and can be regulated over a very wide range, some coatings containing considerable carbon being harder than sapphire. In addition to products already known this method of plating has yielded new carbides of molybdenum and tungsten and alloys supersaturated with carbon. These new products are possible because, in the process of plating, carbonyl can be decomposed at temperatures as low as about 150°C, and thus in the presence of other substances reactions occur which could perhaps not be produced in any other way. In addition to carbides and alloys with carbon, sulphides and oxides of molybdenum and tungsten have been produced and studied. There are certain other advantages of the carbonyl method of plating. It is not required that the base have good electrical conductivity as in electrochemical processes, and the base need not have the temperature stability required in plating from a halide. Thus low melting glasses, as well as other ceramics, can be plated almost as readily as metals. In particular, the plating of glass with

Jan 1, 1949

By C. Baldwin Sawyer

During the last half century, much time has been devoted to investigations of the effect of nitrogen on the physical properties of steel, but in all discussions of results there is considerable doubt as to the accuracy and interpretation of analyses. No conclusions concerning the effects of nitrogen on the physical properties of steel can be more reliable than the methods used for determining the quantities of nitrogen present. The work described in this paper endeavors to establish some additional conditions required by the customary distillation method for reliable and nccurate determinations. Results by a combustion method of analysis for total nitrogen content are presented; these indicate that all of the nitrogen in steel, exclusive of that contained in blowholes, may be determined by the distillation method. Based on these more sound and more reliable analyses, results havc been obtained that bear on the following divisions of the general subject, nitrogen in steel: Nitrification of steel by melting in nitrogen, nitrification of steel by heating in ammonia, decomposition of nitrified steel by heating, and thermal analysis of nitrified steel. Consideration of Two Methods of Analysis and Some Results The details of the distillation and combustion methods are chemical in character and of little interest to most readers. They are therefore described in an appendix. The distillation method is essentially that described by Hurum and Fay1 and was generally used throughout this work. It is capable of the greatest accuracy and all results given are significant to the last, figure. Where analyses do not check, the samples

Jan 1, 1923

By Henry Howe

1. Introduction.-This paper is based in large part on the examination of two rings, shown in section in Fig. 4 to 15, cut from an eroded 14-in. (35.56-cm.) gun, liner, and containing, according to Booth, Garrett, & Blair: Carbon, 0.380 per cent.; manganese, 0.655 per cent.; nickel, 2.810 per cent.; vanadium, 0; chromium, a few hundredths of 1 per cent.; tungsten, 0; molybdenum, 0. These rings were received from Admiral Joseph Strauss, then Chief of Ordnance, U. S. Navy, through the kindness of Mr. Hudson Maxim, Chairman of the Committee on Ordnance and Explosives,, of the U. S. Naval Consulting Board.

Jan 2, 1918

By C. Baldwin Sawyer

During the last half century, much time has been devoted to investigations of the effect of nitrogen on the physical properties of steel, but in all discussions of results there is considerable doubt as to the accuracy and interpretation of analyses. No conclusions concerning the effects of nitrogen on the physical properties of steel can be more reliable than the methods used for determining the quantities of nitrogen present. The work described in this paper endeavors to establish some additional conditions required by the customary distillation method for reliable and nccurate determinations. Results by a combustion method of analysis for total nitrogen content are presented; these indicate that all of the nitrogen in steel, exclusive of that contained in blowholes, may be determined by the distillation method. Based on these more sound and more reliable analyses, results havc been obtained that bear on the following divisions of the general subject, nitrogen in steel: Nitrification of steel by melting in nitrogen, nitrification of steel by heating in ammonia, decomposition of nitrified steel by heating, and thermal analysis of nitrified steel. Consideration of Two Methods of Analysis and Some Results The details of the distillation and combustion methods are chemical in character and of little interest to most readers. They are therefore described in an appendix. The distillation method is essentially that described by Hurum and Fay1 and was generally used throughout this work. It is capable of the greatest accuracy and all results given are significant to the last, figure. Where analyses do not check, the samples

Jan 1, 1923

By S. W. Poole, J. A. Rosa

THE object of this investigation was to determine the distribution of chemical elements within a large, killed alloy-steel ingot, by sulphur printing and quantitative chemical analysis. With regard to segregation in steel ingots, the factors of melting practice, pouring temperatures, mold design, etc., and the mechanics of solidification and its attendant functions, have been the subject of intensive study over a period of years by many investigators. Notable among these is the Sub-Committee of the No. 5 Committee of the British Iron and Steel Institute. For an exposition 0f the many problems awaiting the researcher on the heterogeneity of steel ingots, the methods of attacking these problems, together with some of the answers, the reader is referred to the nine reports and numerous papers of that committee and its membership. STEELMAKING DATA Melt.-The heat was made in a 70-ton direct arc-type basic electric furnace. Furnace charge consisted of nickel-chromium-molybdenum steel, most of it in the form of heavy mill scrap. All of the scrap was charged cold. The standard double-slag method was employed, the heat being finished under a strong carbide slag. Aluminum was used as the deoxidizing agent. Tapping temperature, as observed with an optical pyrometer, was 3000°F. Detail of Mold and Ingot Size.-Details of the ingot mold and the ingot itself are given in Fig. I. Teeming.-Teeming temperature of the subject ingot as observed with an optical pyrometer was 2830°F. The ingot was top-poured directly through a 1 ½ in. nozzle and required 7 min., 44 sec. to fill up to the hot top. An additional 2 min., 30 sec. were required to fill the hot top. The ingot was stripped hot and charged with the remainder of the heat into an annealing furnace. There it was given the standard annealing cycle used for these ingots. Subsequent heat-treatments are described elsewhere in this paper. SECTIONING AND PREPARATION FOR SULPHUR PRINTING Because of previous favorable experience in sectioning ingots up to 21 ½ in. square with an oxyacetylene torch, it was decided to use this method to section the subject ingot. The ingot was preheated to 900°F. for 12 hr. It was then placed on a steel bed in a horizontal position so that the longitudinal axis was level and parallel to the track of the motor-driven torch carrier. Two cuts were made, one 2 in. above the longitudinal axis and the other 2 in. below. The time required to make each cut was approximately 75 min. The cutting operation is shown in Figs. z and 3. The 4-in. thick slab was mmediately charged into a furnace standing at 1200°F.

Jan 1, 1944

By Alfred H. Bell, George V. Cohee

In 1939 Illinois produced 94,302,000 bbl. of oil—almost three times the amount of oil produced at the peak in 1908, when development in the southeastern Illinois field was at its height (Fig. I). It represents nearly a fourfold increase over the 24,075,000 bbl. produced in 1938 (Table 6). This rapid increase in oil production in Illinois is largely due to development in the Salem and Louden fields (Table I). During 1939 daily production for the state increased from 135,000 to 332,572 bbl. A notable increase in production for 1940 is expected as a result of the drilling of the Devonian limestone in the Salem and Centralia fields,

Jan 1, 1940

By Alfred H. Bell, George V. Cohee

In 1939 Illinois produced 94,302,000 bbl. of oil—almost three times the amount of oil produced at the peak in 1908, when development in the southeastern Illinois field was at its height (Fig. I). It represents nearly a fourfold increase over the 24,075,000 bbl. produced in 1938 (Table 6). This rapid increase in oil production in Illinois is largely due to development in the Salem and Louden fields (Table I). During 1939 daily production for the state increased from 135,000 to 332,572 bbl. A notable increase in production for 1940 is expected as a result of the drilling of the Devonian limestone in the Salem and Centralia fields,

Jan 1, 1940

By A. Bleier, E. D. Goddard, R. D. Kulkarni

The influence of the collector structure on the amine (RNH2, R=alkyl) flotation of quartz has been systematically investigated using a modified Hallimond microflotation cell. This study focuses on the effect of varying chain length, branching in the alkyl group R, polyfunctionality of the collector molecule, and alkyl substitution on the nitrogen atom. In addition, adsorption at the solution/air interface and electrokinetic results for the solid/solution interface were employed to further elucidate the role ad the interrelation of the structural parameters in the flotation process. Estimates of an electrical double layer attractive energy between the bubble and the solid particle are made.

Jan 1, 1976

By Osamu Fukuta

The geological and geochemical characteristics of the Japanese iodine-rich brines are outlined. The iodine-rich brine in Japan is primary in its origin and its occurrence is limited in the younger marine sediments. The iodine-rich subsurface water is saturated or over- saturated by natural gas, but the water saturated by natural gas is not always rich in iodine. The iodide and bromide contents decrease with time. The bromide content decreases much more rapidly than that of iodide. It should be emphasized that the genetic environment of the Japanese type of dissolved gas and iodine deposit is not peculiar to the Japanese islands.

Jan 1, 1985

By M. Gensamer

A RECENT paper1 described, by means of stereographic pole figures, the preferred orientations produced by cold-rolling low-carbon steel of automobile-body grade. It was found that the surface of the sheet exhibited a deformation texture significantly different from the texture possessed by the inside of the sheet. Efforts to produce the surface texture by buffing a sample exhibiting the normal or inside texture, using a copper lap, have not been successful. In view of the data collected, by Kurdjumow and Sachs2, it was suggested that the surface texture might be the result of partial recrystallization of the normal or inside texture. The recrystallization texture of cold-rolled mild steel was studied by Goss3, but he did not use the pole-figure method, so that his conclusions were in need of verification. For these reasons the work reported in the present paper was undertaken. It had two objectives: (1) to study the general behavior of cold-rolled mild steel on recrystallization below the critical temperature A,, and (2) to attempt experimentally a demon-stration of the genesis suggested above for the surface texture in cold-rolled steel. The material was that used by Gensamer and Mehl, cold-rolled to 97.5 per cent reduction in thickness. Fig. 1 is an X-ray pinhole photo-gram of this material, taken with the beam transmitted perpendicular to the plane of the sheet, using a molybdenum target at 35 kv. with no filter. It is typical of the inside texture, but in it the deformation texture is better developed than in the samples that showed a well developed difference between the inside and surface samples. Specimens from this sheet, which was 0.005 in. thick, were annealed for 5 min. at various temperatures in a lead bath. After about 0.0005 in. had been etched from both surfaces, X-ray photograms were prepared, using the technique described in the earlier paper'.

Jan 1, 1936

By C. Schlumberger

THE object of this paper is to describe the adaptation of electrical resistivity measurements to the particular case of exploration in which the surface is an expanse of water (river, lake, sea). Water in itself does not constitute an obstacle to electrical exploration. It is merely an overburden, which is fluid instead of being solid, and as a consequence the routine of the measurements has to be modified. Also, in many instances, the liquid under consideration is highly conductive (salt water). This introduces an additional difficulty into exploration work, and has to be overcome by the geophysicist. We do not propose to discuss here the basic principles of electrical resistivity measurements, which have been dealt with in various previous papers,1 but will simply recall the two fundamental techniques which govern its field application: 1. Horizontal exploration, or method of the resistivity map, in which a series of electrical measurements are carried out at various stations, keeping the same electrode spacing. Thus, a horizontal layer of the subsoil, of a practically constant thickness, is explored. 2. Vertical exploration, or "vertical sounding?2 method, in which a series of measurements are made with increasing electrode spacings at one or several stations. In this way, the apparent resistivity is deter-

Jan 1, 1934

By Paul T. Benson

MOST important of the various departments of a custom smelter, so far as the financial welfare of the plant and the confidence of shippers are concerned, is that responsible for correct weights, accurate moisture sampling, and the obtaining of control samples that are strictly representative of the lot of ore from which they come. Treatment rate schedules are based on the metal content of ores received, reduced to dry weight. These rates must be low enough to keep the ship- per from taking his business else- where and still must allow the smelter a profit. Assay results, likewise, must satisfy the shipper, but if they show too high a metal content for the ore they represent, the smelter will actually lose money. It is always considered, and constant checks through umpire assays prove, that laboratory results are closely correct, so the bur- den of the plant profit and loss and the satisfaction of the shipper rest squarely upon the sampling department.

Jan 1, 1936

By Alden B. Greninger, Alexander R. Troiano

Metallurgists have long believed that martensite in steel forms as plates along the octahedral {111} planes of austenite. Much has been written about mechanisms whereby units of the austenite lattice are pictured as transforming to martensite by shearing movements initiated along the octahedral planes of austenite, supposedly resulting in plates of martensite lying parallel to these planes of shear. A critical inspection of two or three photomicrographs of quenched hypereutectoid steel led us to the conclusion that the orientation habit of martensite, at least in hypereutectoid austenite, could not possibly be octahedral. Inasmuch as recent studies,30,31 of the martensite-type reaction in nonferrous alloy systems have established the irrational orientation habit as characteristic of this type of lattice transformation, the need for a thorough restudy of the crystallography of martensite formation in steel was evident. The present paper reports the results of such a study, extended to include both cementite and some of the products of constant-temperature decomposition of austenite. Also reported are a few of the results obtained from a microscopic and X-ray study of the austempering process in very high-carbon steel. I. The Martensite Transformation Previous Work Microstructure and Crystal Structure of Martensite.—Among the best series of published photomicrographs of quenched steels are those of Whitely,1 Robertson,2 Hanemann and Schrader,3 and Lucas.4 The crystal structure of martensite is body-centered tetragonal, with axial ratio varying from 1 near 0.0 per cent carbon to 1.08 for 1.75 per cent

Jan 1, 1940

By Charles Wraith

THE property of the Roan Antelope Copper Mines, Ltd., is situated at Luanshya, north-central part of Northern Rhodesia, and is connected with the main line of the Rhodesia Railways, Ltd., by a 24-mile branch line from N'dola. Most of the material and supplies that are not available in Africa are shipped into the country via Beira, on the East Coast of Africa, a distance of 1473 miles from Luanshya and the nearest ocean port. The output of copper is shipped by rail to Beira and thence by boat to the market. Passenger travel is mostly via Cape Town, a distance of 2162 miles from Luanshya. Excellent passenger trains operate on regular schedules between Cape Town and Northern Rhodesia. Luanshya is 13° south of the equator at an elevation of 4000 ft. above sea level, and has a mild healthful climate. During the rainy season, from October to March, the rainfall averages 53 in. The area is pro-fusely covered with vegetation. An ample supply of water for industrial and domestic purposes is available throughout the year. The more important supplies for smelting purposes, such as wood, coal, limestone, silica, quartzite, and clay for "dolly" mud, are con-veniently available. Excellent grades of coal, coke and firebrick are obtained from the Wankie Colliery Co., Ltd., Southern Rhodesia. The Wankie colliery has just completed the erection of equipment for the manufacture of silica brick. An ample supply of quartzite of good grade is available for this purpose. Silica brick is also obtained from the Belgian Congo and from India. Limestone is quarried from a large deposit a few miles from Bwana Mkubwa, which is 30 miles by rail from the smelter. An abundant supply of clay for "dolly" mud and for lining launders is available within a short distance of the smelter.

Jan 1, 1933

By W. P. Lass

The purpose of this article is not only to describe the plant and method of cyaniding the Treadwell concentrates, but to present some of the results of the experimental work obtained in the past three years for the Alaska-Treadwell Qold Mining Co., at Douglas Island, Alaska, under the direction of F. W. Bradley, Consulting Engineer, and Robert A. Kinzie, General Superintendent, of the affiliated companies. At the time the experimental work was undertaken the concentrates were being shipped to the smeltery at Tacoma, Wash., and the cost for treatment of 3-oz. (gold) concentrates was $11.95 per ton, divided as follows : Smelting-charges,......... $4.00 Loading, freight, insurance, etc., . 2.89 Interest due to time loat in transit and in settlement,... 0.05 Loss due to settlement for 95 per cent. of the gold at $20 per ounce, 6.01 Total,...$11.95 From the experimental work described later, it was estimated that 96 per cent. extraction could be made by treatment on the ground, and that the cost, when treating 80 tons per day, would be $3.25 per ton, divided as follows : Per Day. Per Ton. Labor,. $86.16 $@.827 Chemicals,.76.60 0.960 Power and steam-heat,... 67.60 0.845 Marketing-, refining- and other charges, . 49.36 0.617 Totals,.. $2.59.72 $3.250 Adding to this total the 4 per cent. treatment-loss, which on 3-02. concentrates amounts to $2.48, gives a total cost of $5.13 per ton. Comparing this with $11.95, the cost when shipping to the smelter, leaves a net gain of $6.22 per ton by the local

Jan 1, 1912

By Lyall Zickrick, R. S. Dean, F. C. Nix

The first attempt to establish an equilibrium diagram of the lead-antimony series was made by Roland-Gosselinl in 1896. This investigation classified the system as a purely eutectiferous one, with the eutectic at 12.5 per cent. antimony and 228" C. In the next year, Stead2 placed the eutectic temperature at 247' C. The error in temperature made by Roland-Gosselin, however, has been perpetuated in the literature with a remarkable degree of persistency; this value was accepted by Campbell (1902), and Ewen (1910),3 and will be found in the last edition of Desch's3 Metallography (1922). Gonterman's investigation, made in 1907, was the most complete one available at the time .the present investigation was started. He concluded4 that the system was a simple eutectiferous one and placed the eutectic at 13 per cent. antimony and 247° C. Other investigations by Tammann (1907),5 Garbow (1909),6 Rudolfi (1910),7 Loebe (1911),8 and Leroux (1913)9 added little, if anything, to Gonterman's diagram. A number of investigations have been made of physical properties of the alloys. The electrical conductivity of the series was studied by Matthiessen (1860)10 and by A. W. Smith (1921);11 the thermoforce by Rudolfi (1910),12 and Pelabon (1923) ;13 the specific heat by Durrer

Jan 1, 1926

By Alden B. Greninger, Alexander R. Troiano

Metallurgists have long believed that martensite in steel forms as plates along the octahedral {111} planes of austenite. Much has been written about mechanisms whereby units of the austenite lattice are pictured as transforming to martensite by shearing movements initiated along the octahedral planes of austenite, supposedly resulting in plates of martensite lying parallel to these planes of shear. A critical inspection of two or three photomicrographs of quenched hypereutectoid steel led us to the conclusion that the orientation habit of martensite, at least in hypereutectoid austenite, could not possibly be octahedral. Inasmuch as recent studies,30,31 of the martensite-type reaction in nonferrous alloy systems have established the irrational orientation habit as characteristic of this type of lattice transformation, the need for a thorough restudy of the crystallography of martensite formation in steel was evident. The present paper reports the results of such a study, extended to include both cementite and some of the products of constant-temperature decomposition of austenite. Also reported are a few of the results obtained from a microscopic and X-ray study of the austempering process in very high-carbon steel. I. The Martensite Transformation Previous Work Microstructure and Crystal Structure of Martensite.—Among the best series of published photomicrographs of quenched steels are those of Whitely,1 Robertson,2 Hanemann and Schrader,3 and Lucas.4 The crystal structure of martensite is body-centered tetragonal, with axial ratio varying from 1 near 0.0 per cent carbon to 1.08 for 1.75 per cent

Jan 1, 1940