Search Documents

By Orson Cutler Shepard

RECENT research work in the flotation concentration of minerals has been concerned mainly with flotation reagents and the mechanism by which collecting reagents are held to the surface of certain mineral particles. The fundamental question of why air bubbles cling to properly prepared mineral surfaces is usually dismissed with the statement that the surface is air-avid or water-repellent. In my article in MINING AND METALLURGY for June, 1932, I showed theoretically that surface tension relationships govern bubble attachment in Rotation. This explanation has not been accepted by many; probably be¬cause the difficulty of measuring solid-solution surface tensions prevented obtaining experimental evidence. If the surface tensions involved in the system [solution, mineral, air bubble] are responsible for attachment of the air bubble to the mineral, any change in the surface tensions should cause a corresponding change in the attachment of the air bubble. An example in which the mineral-solution surface tension could be varied was found with mercury. When mercury is in contact with solutions of certain electrolytes the surface tension at the contact of mercury and solution can be altered by electrical polarization of the mercury. The surface tension rises to a maximum as the mercury is given an increasing negative potential and then decreases with further increase in potential. The theoretical relation between the surface tensions and the attachment of an air bubble is given by the following equation:

Jan 1, 1936

By Michael Perch, Charles C. Russell

Nearly 7 5 per cent of the total coke production in the United States in 1940 was consumed in blast furnaces. In 1939 the percentage was 69.9, and in 1938 it was 61.3. To produce a net ton of pig iron 1757 lb. of coke was required in 1940 and 1760 lb. in 1939. These figures indicate how dependent the production of pig iron is upon the production of coke. The rate of iron production is in some measure influenced by the physical and chemical characteristics of the coke. Blast-furnace operators believe that the physical properties of coke profoundly influence the operation of the furnace. Although it is true that coke of a wide variety of physical properties is used in American blast furnaces, the periodic fluctuation of these properties is one of the causes of irregularity of blast-furnace operation. The purpose of this paper is to present a broad picture of the physical properties of by-product coke that are generally considered to be important by coke-oven and blast-furnace operators. Effects of the kind of coal used, the preparation of the coal, the rate of coking, and other factors will be considered. Of all these variables, the kind of coal used is by far the most important. In this discussion use will be made of the method of coal classification by rank1 standardized by the American Society for Testing Materials. Although this method of classification has been an American standard for several years, it has not been given the attention it deserves, especially in connection with the selection of coal for production of coke. Despite the fact that many producers of blast-furnace coke are limited to some particular source or sources of coal, a good understanding of the principles involved in setting up the standard method of classification may lead to a better appreciation of the causes of changes in coke characteristics. Furthermore, where it is necessary to select new coals as a substitute for the original supply, this method of classification can be of great assistance. The data presented have been gathered from many sources, but no attempt has been made to cover the vast literature. Instead, some of the more important data have been selected to show how coals and their carbonization affect some of the physical properties of coke. It must be emphasized that generalizations concerning the behavior of coking coals are presented and that individual coals may vary widely from the specific behavior depicted. Nevertheless, it is believed that the data illustrate certain typical behaviors. Neither was it possible to cover completely all the factors involved; for example, the macroscopic constituents of coal are believed to have important effects on the physical properties of coke, but since there is little information available for such study, and since vitrain, clarain, and durain are neither

Jan 1, 1943

By Henry S. Rawdon

Any laboratory corrosion test, as judged from the practical point of view, is valuable only to the extent that it foretells what will, in all probability, occur in service. Such a test is most properly to be considered as a "pilot test," that is, a test which indicates the direction along which action may be expected to occur rather than as a truly quantitative test which would be expected to tell just how and to what extent the action would proceed. It is generally recognized that laboratory corrosion tests should be chosen with particular reference to the character of service expected for any particular type of metal, so far as it can be foreseen. Even when this requirement has been fulfilled, however, the question whether the actual service behavior of the material is in accordance and general agreement with predictions based upon such laboratory tests is always a pertinent one. The information available in the technical literature bearing on the correlation between the service behavior of metals from the corrosion standpoint, and the results obtained with the same metals in laboratory corrosion tests is very meager, indeed. The results which have been obtained in weather-exposure tests of sheet duralumin which form the body of this discussion are presented here for their bearing on this particular phase of the problem of the corrosion resistance of duralumin. Although the exposure tests described have not been completed, in the sense that all of the tests, in the series initially laid down, have been accomplished, still the general trend shown by the results is so clear that a number of definite conclusions at this stage (subject, of course, to possible modification in the light of later results) are believed to be warranted. The tests reported upon here form one phase of the much broader study of this subject which has been under way for several years in which the National Advisory Committee for Aeronautics, the Bureau of Aeronautics of the Navy Department, the Army Air Corps and the Bureau of Standards have cooperated. Without the very helpful cooperation of the manufacturers in furnishing the

Jan 1, 1929

By C. E. Cottrell, G. W. Preckshot, N. D. Delisle, D. L. Katz

Most crude oils contain asphaltic substances that may be naturally or artificially precipitated. In the Greeley field, California, this asphaltic bitumen is precipitated during the flow of the oil from the reservoir to the stock tank The mechanism of such precipitation is not well understood. This paper presents the progress that has been made by using the electron microscope as a new tool and by observing the effects of the streaming potential on the formation of bitumen particles. Crude oils at atmospheric pressure viewed in the electron microscope in very thin films under a vacuum showed no asphaltic particles. A technique of preparing slides of thin films by dilution of the oil with benzene and washing in petroleum ether was used at first, and these observations showed that the solvents caused the formation of the particles, varying from 0.01 to 0.2 micron in diameter. The electrical effects of fluids flowing through porous solid were studied, with emphasis on the formation of colloidal particles by the streaming potential. The streaming potential of crude oil flowing through sand was measured and was shown to be responsible for the formation of bitumen particles. These results bring out a new phenomenon, which may occur when crude oil flows through the porous oil reservoir. mechanisms. Asphalt has been the subject of widespread investigation but, owing to the complexity of the substances being considered, progress has been slow. Investigators working primarily with the asphaltic substances have treated the subject from the colloidal standpoint and have developed theories that picture the asphaltic particles as surrounded by adsorbed materia1s.14,15,17,24 The deasphaltization of lubricating oil by the use of solvents treats the subject primarily from the standpoint of liquid-liquid equilibria.'' A complete understanding of asphaltic substances would make possible the following of the material from its initial state in the crude oil through precipitation processes to the final plastic stage, the most common form of which is used in asphaltic pavements. Since these asphaltic particles are very small, it appears 'hat the electron microscope4 might be a useful tool in studying the precipitation processes. Specimens are examined by the electron microscope in a vacuum and as very thin films, requiring special techniques in preparation of samples. A brief description of the electron microscope and its operation will bring out the difficulties and advantages of its use for this problem. The first work was done with crude oils that had been diluted with solvents for the preparation of the film to be examined. Later a technique was developed by which the undiluted oil film could be made thin enough for direct examination. These two techniques show vastly different results Asphaltic particles have been precipitated from crude oils by a variety of

Jan 1, 1943

By J. L. Huitt, B. B. McGlothlin

The introduction of new fracture propping agents that are brittle but much stronger than sand created the problem of what loading strength is required for a propping agent to be effective in a given formation. It is shown that the load at which the propping agent crushes should exceed the load at which total embedment in the fracture faces is possible. Simple laboratory tests to determine loading strength of the propping agent and embedment in the fracture faces, and use of these data in selecting a propping agent for a given formation, are discussed. INTRODUCTION One of the most important factors in the design of hydraulic fracturing treatments is the selection of a propping agent that can effectively provide the fracture flow capacity needed for stimulation of a well. Sand, once generally accepted as being synonymous with propping agent in hydraulic fracturing, is now recognized as having limited effectiveness in many formations because of its low resistance to crushing. Sand particles are brittle and have relatively low strength. Because of this property, sand particles are crushed in rocks that offer high resistance to the penetration of fracture faces by the proppant particles when the fracture attempts to close under the action of the overburden load. For rocks that offer a high resistance to penetration, deform able particles are more effective propping agents than sand. However, for this same type of rock, a propping agent that does not deform, yet does not crush, is often more effective. Thus, a rigid propping agent with sufficient strength to prevent crushing is desirable. A method for determining the strength required for a rigid propping agent to function effectively in given formations is discussed. BEHAVIOR OF RIGID PROPPANTS AND FRACTURE FACES RELATED STUDIES An early qualitative description of the reaction of propping sand in fractures was given by Hassebroek et al.' In discussing fracturing in deep wells, the authors mentioned that even though propping sand entered the fractures, a high flow capacity did not result due to crushing or embedding of the propping sand. Dehlinger et al.2 in discussing the reaction of propping sand surmised that, because of the hardness of sand particles, deformation occurred in the fracture faces contacting the propping sand. In later studies,3,4 methods of determining the embedment of propping sand in fracture faces of soft rock and the critical load at which propping sand is crushed by the fracture faces in hard rock were discussed. In working with de-formable proppants, Kern et al. considered proppant particles to be deformed into cylindrical disks by action of the overburden and then pressed slightly into the fracture faces by further action of the overburden. Rixie et al.'0 reported on embedment pressure and presented a method of selecting a propping agent for use in given formations. The propping agents included sand, walnut shells and aluminum pellets. All these studies have contributed materially to a better understanding of propping agent behavior; however, the strength of brittle proppants (sand, glass and ceramics) required to result in embedment rather than crushing has not been discussed. This topic will be covered in the ensuing discussion. PROPPANT PARTICLE CRUSHING—-EMBEDMENT For this discussion, a rigid propping agent is considered to be one that is brittle and fails under tensile stress when loaded to a critical value. In an earlier study4 it was shown that the Hertzian4 loading theory could be applied to a spherical brittle propping agent if the propping agent and fracture faces behaved elastically. At the failure of the proppant, the ratio of the load to the square of the diameter of the particle should be constant for a given material combination, or: Lc/dp2=C ............(1) A partial derivation of this equation from proppant and formation properties is included in the Appendix. Should a rigid particle not be crushed as a load is applied, it embeds in the fracture faces. A study3 of particle embedment in fracture surfaces has been published. The embedment can be described by an equation based on Meyer's metal penetration hardness relationships: d1/dp=B 1/2[L/dp2]m/2..........(2) In Eq. 2, B and m are constants that are characteristic of the rock; the significance of the other terms is shown in Fig. 1. A STANDARD DEFINITION FOR PROPPANT LOADING STRENGTH Eq. 1 is useful in appraising propping agent strength," but it is strictly applicable only when the area of contact between a particle and a fracture face (or loading plate)

Jan 1, 1967

By H. Rosenthal, A. L. Jamieson

THE action of mercury on stressed brass to produce cracks was known before Moore, Beckinsale and Mallinson1 showed that actual season cracking did not occur spontaneously but could be induced by ammonia. These investigators studied other substances, including diphenylamine, without finding that anything other than ammonia could cause season cracking. Grimston2 reported season cracking in cartridge cases stored in wooden boxes wetted with dilute sulphuric acid pickling solution. Season cracking associated with sulphur dioxide, water vapor and air has been reported by Johnston,3 although he reported that trimethylamine and pyridine did not cause cracking. Jevons4 has ascribed season cracking of brass in certain instances to trimethylamine, "aldehyde amine," "ketone amine" and pyridine, but no experimental work was done evidently to prove this definitely. Pyridine was investigated by Morris,' who found it to have considerable cracking power. In the present investigation, the object was a qualitative evaluation of a number of representative amines with respect to their ability to cause season cracking. Thus it was desired only that an appreciable vapor pressure of each amine be obtained in order to make the test as severe as possible, without attempting to test equivalent concentrations for comparative purposes. METHODS Specimens Two types of specimen were used: I. Unannealed 70-30 brass cups formed from 0.040-in. thick sheet. Height of cup was 1 3/8 in. and diameter was 1 7/8 inches. 2. First draw pieces of caliber .50 cartridge cases in the unannealed condition (70-30 brass). The cups were representative of a thin wall and thin base specimen, whereas the draw pieces have a thick base (1/4 in.) and a thick wall (approximately 3/32 in.). Both types of specimens contained high residual stress and cracked in less than one minute in a solution of I per cent mercurous nitrate and I per cent nitric acid provided that this was preceded by a 30-sec. pickle in 40 per cent nitric acid. Specimens were prepared as follows: (I) degreased in trichlorethylene, (2) rinsed in H20, (3) pickled 5 min. in 10 per cent by volume H2SO4 (1.84 sp. gr.), (4) rinsed in H2O, and (5) dried. Amines Tested In selecting the amines, representatives of the three series of amines and one series of substituted amines were chosen. The aliphatic series was represented by the methyl and ethyl primary, secondary and tertiary amines. These are the simplest aliphatic amines. For the aromatic series, the phenyl primary, secondary and tertiary amines were selected as being the simplest. The heterocyclic series was represented by pyridine, which is a simple heterocyclic base (tertiary amine).

Jan 1, 1944

By G. W. Preckshot, C. E. Cottrell, D. L. Katz, N. D. Delisle

Most crude oils contain asphaltic substances that may be naturally or artificially precipitated. In the Greeley field, California, this asphaltic bitumen is precipitated during the flow of the oil from the reservoir to the stock tank The mechanism of such precipitation is not well understood. This paper presents the progress that has been made by using the electron microscope as a new tool and by observing the effects of the streaming potential on the formation of bitumen particles. Crude oils at atmospheric pressure viewed in the electron microscope in very thin films under a vacuum showed no asphaltic particles. A technique of preparing slides of thin films by dilution of the oil with benzene and washing in petroleum ether was used at first, and these observations showed that the solvents caused the formation of the particles, varying from 0.01 to 0.2 micron in diameter. The electrical effects of fluids flowing through porous solid were studied, with emphasis on the formation of colloidal particles by the streaming potential. The streaming potential of crude oil flowing through sand was measured and was shown to be responsible for the formation of bitumen particles. These results bring out a new phenomenon, which may occur when crude oil flows through the porous oil reservoir. mechanisms. Asphalt has been the subject of widespread investigation but, owing to the complexity of the substances being considered, progress has been slow. Investigators working primarily with the asphaltic substances have treated the subject from the colloidal standpoint and have developed theories that picture the asphaltic particles as surrounded by adsorbed materia1s.14,15,17,24 The deasphaltization of lubricating oil by the use of solvents treats the subject primarily from the standpoint of liquid-liquid equilibria.'' A complete understanding of asphaltic substances would make possible the following of the material from its initial state in the crude oil through precipitation processes to the final plastic stage, the most common form of which is used in asphaltic pavements. Since these asphaltic particles are very small, it appears 'hat the electron microscope4 might be a useful tool in studying the precipitation processes. Specimens are examined by the electron microscope in a vacuum and as very thin films, requiring special techniques in preparation of samples. A brief description of the electron microscope and its operation will bring out the difficulties and advantages of its use for this problem. The first work was done with crude oils that had been diluted with solvents for the preparation of the film to be examined. Later a technique was developed by which the undiluted oil film could be made thin enough for direct examination. These two techniques show vastly different results Asphaltic particles have been precipitated from crude oils by a variety of

Jan 1, 1943

By Walter C. Lawson

The primary objective in laying track in panel sections is to reduce the number of track laborers required. This is possible because the work is mechanized. Moreover, because the work is mechanized and each of the operations needs only a few men, and each is self-contained, the work can be carried on at night as well as in daylight; therefore, the method provides a means of preparing tracks on more than one shift. The laying of tracks in open pits and quarries in panel sections is not new but new methods have been made possible by the introduction of new types of equipment. The purpose of this paper is to describe the methods that are followed in the Morenci open pit. General Mining Operations Full-scale ore production at Morenci is about 50,000 tons daily. The normal yearly output of ore and waste is 32,000,000 tons, of which 30,000,000 tons is handled by rail haulage. This requires the building of approximately 47 miles of loading and other temporary tracks during a 12 months' period (Fig I). Broken ore and waste is loaded into 90-ton capacity dump cars with 5-cu-yd full-revolving electric shovels. Shovel banks are uniformly 50 ft high. They are blasted with churn drill holes and the broken material from a blast is loaded out with two shovel cuts, the first one being called (locally) the "splatter" cut and the second one the "clean-up" or "face-up" cut. When a shovel is making its clean-up cut, the loading track is about 70 ft from the toe of the bank and, under normal conditions, a bank is blasted against it without removing the track. It is thus evident that each track is used for two shovel cuts before relocation is necessary, inasmuch as a single position serves for both the clean-up cut prior to blasting and for the splatter cut following the blast. The normal advance of a solid bench by a single blast is 40 ft (Fig 2). Preparation OF Panel Grade In preparation of panel grades bulldozers and rooters are used for the bulk of the work and an auto-patrol road grader for the final stage. At Morenci, bulldozers have always been used for track-grade preparation, but before the introduction of the other two types of equipment grades were uneven and irregular at best, and always necessitated a big gang of track laborers to hand-block under the ties with rocks after a track was laid into place. High blocking also made poor track because of instability and caused frequent derailments. Under these conditions derailments were generally bad as re-railing became difficult. Much track was torn up and many tics broken in the process. The inadequacy of the hand-blocked track, together with the inefficiency of hand blocking, constantly pointed, to the desirability of reducing the amount of labor required, so various means were tried to improve conditions, such as wood

Jan 1, 1949

By Mayumi Someno, Kazuhiro Goto, Masahiro Kawakami

The apparent rates of decarburization of liquid alloys of Fe-C, Fe-C-S, Ni-C, and Co-C systems and the rate of oxidation of solid graphite with pure carbon dioxide gas and with gas mixtures of carbon monoxide and carbon dioxide have been measured in the temperature range of 1000° to 1600°C. The cotnposition of carbon dioxide and carbon monoxide gas at the reaction surface has been measured by oxygen concentration cells with the ZrO,-CaO solid electrolyte. 1) The apparent rates of the carbon removal are essentially the same for all the cases of solid graphite, Fe-C, Fe-C-S, Ni-C, and Co-C systems under the same experimental conditions. 2) The apparent rates are independent of the carbon content in the high carbon concentration range but very much affected by the flow rate and the gas composition of the CO-CO2 reactant gas mixture. The ratio of the gas consumed by the reaction to the total quantity of the supplied gas is very large under the present experi~nental conditions. 3) There is a concentration gradient of' carbon dioxide in the vicinity of the reaction surface and the content of CO, becomes extremely small at the reaction surface. 4) A large time fluc-tuation of the gas composition was observed. This jluctuation implies the presence of unstable flow in the gas phase in the vicinity of the reaction surface. THE decarburization of molten steel by an oxidizing gas or by slag may be one of the most important chemical reactions in steelmaking processes. Nevertheless, the kinetics of this heterogeneous chemical reaction do not seem to be well-solved even with the previous studies. Although the conditions for the reaction in steelmaking processes are quite different from those in the laboratory scale, some critical experiments may give information on the mechanism of the decarburization. From the previous work,'-' it is known that the rate of the decarburization is independent of the carbon content in liquid iron with more than about 0.2 wt pct C when the oxidizing gases are supplied to the surface of liquid Fe-C alloys on a laboratory scale. Two rate-controlling steps have been proposed for the decarburization of liquid iron with the high carbon content: one is the surface reaction control proposed by Swisher and Turkdogan;' the other is that the rate is controlled by the gaseous diffusion through the gaseous stagnant layer. proposed by Baker. Warner, and Jenkins.7 and also by .Ito and Sano.2 In the present study, some experiments have been carried out for the evaluation of these rate-controlling steps in the decarburization of liquid iron with high carbon content. The apparent rate of decarburization of liquid iron has been compared with the rates of carbon removal of liquid Ni-C, Co-C, and solid graphite under the same experimental conditions. The composition of carbon dioxide and carbon monoxide gas at the reaction surface has been measured by oxygen concentration cells. I) EXPERIMENTAL PROCEDURE Fig. 1 shows the schematic diagram of the reaction chamber. Solid graphite and liquid metals were contained in an alumina or magnesia crucible of 32 mm ID and 35 mm in height. The samples were heated by high-frequency induction and the temperature was measured by the calibrated optical pyrometer. The temperature was held constant to within 10°C. The re-actant gases were supplied to the surface of the samples through the quartz tube of 8.0 mm ID. The distance from the end of the quartz tube to the surface was 20 mm. The block of high-purity graphite was cut and shaped to the inner profile of the crucible. The height of the shaped graphite was 18 mm, which corresponded to the depth of the liquid iron of 100 g. About 100 g of Fe-C alloy (4.20 to 4.40 pct C), Ni-C alloy (1.84 pct C), Co-C alloy (1.85 pct C), and Fe-C-s alloy (4.35 pct c, 0.5 or 1.0 pct S) were melted in the crucible. The reactant gases were pure CO, and gas mixtures of CO-CO,: the flow rates were controlled by capillary flowmeters with bleeders.

Jan 1, 1970

By Henry S. Munroe

THE earliest accounts we have of Japan represent the country as having great mineral wealth, especially of precious and useful metals. Marco Polo, the Venetian traveller, in the thirteenth century, writes of "Zipangu:” "They have gold in greatest abundance, its sources being inexhaustible. The king does not allow of its being exported. To this circumstance we are to attribute the extraordinary richness of the sovereign's palace. The entire roof is covered with a plating of gold. . . . The ceilings of the halls are of the same precious metal ; many of the apartments have tables of pure gold of considerable thickness, and the windows also have golden ornaments." Marco Polo also gives an account of an unsuccessful Tartar expedition against Japan, prompted by the supposed great wealth of the country. Columbus also, as well as many other explorers, were attracted and encouraged by these prevalent reports of the wealth of the islands of Zipangu. Kaempfer, writing in 1727, speaks of the great mineral wealth of Japan, and especially of the abundance of gold, which, he says, is found in many provinces. The Portuguese and Dutch, while they had trading-posts in Japan, furnished tangible evidence of the truth of the early reports. Between 1550 and 1639 the Portuguese merchants sent home from Japan nearly three hundred million dollars' worth of bullion, most of which was gold. As the relative value of equal weights of gold and silver was then six to one, while in Europe, at the same time, it was nearly twelve to one, the exchange of silver bullion for gold was by no means an unimportant part of their business. After the Portuguese, the Dutch continued the exportation of bullion, and the exchange of silver for gold, though with less profit, as the relative value of gold increased with the demand. Between 1649 and 1671 the Dutch traders sent home over two hundred million dollars in bullion, of which, however, nearly two-thirds was silver. In 1671 the Japanese government, alarmed at the rapid rate at which the precious metals were leaving the country, issued an edict forbidding the exportation of gold or silver, under heavy penalties, which had the immediate effect of stopping this trade. Besides bullion, copper formed at this time a most important article of export. According to Dr. Geerts,* who has examined the old * Transactions Asiatic Society of Japan, vol. iii, p. 41.

Jan 1, 1877

By C. A. Bruch, W. E. McHugh, R. W. Hockenbury

EXPERIMENTAL results of the last decade have shown that both accelerator particles and reactor radiations produce significant changes in the properties of metals. These changes, called radiation damage, are important from both academic and engineering viewpoints. An understanding of the radiation damage produced by reactor radiations is difficult, because many kinds of particles having varying energies are present. Therefore, many fundamental studies are being conducted using accelerators in order to obtain nearly mono-energetic beams of various charged particles. Furthermore, many of these experiments are conducted at low temperatures in order to freeze in the radiation-produced lattice defects, after which the specimens are annealed to study the movement of the defects. It is found that although much of the low temperature radiation damage disappears by annealing at room temperature, a significant amount remains. Because there is no assurance that irradiation followed by annealing at a higher temperature will produce the same effect as irradiation at the higher temperature, and because there is an immediate interest in reactor radiation effects during exposures at and above room temperature, a major program is in progress at this laboratory to investigate some of these effects. This paper, representing a part of the program, compares the radiation damage to a group of metals which were exposed under nearly identical irradiation conditions. The metals, representing the three major crystal systems, include copper, nickel, titanium, zirconium, iron, molybdenum, and type 347 stainless steel. The effects of reactor radiations have been treated from a theoretical viewpoint by Seitz' and Ozeroff.' The problem considered by them has been the atomic displacements produced in an infinite medium by mono-energetic beams of both neutrons and charged particles. For reactor experiments, this treatment is not wide enough in scope, because specimens and reactor components are finite, and there are continuous energy spectra of the various particles. Therefore, the theoretical considerations will be extended in this paper to cover reactor conditions and the findings will be compared with the observed radiation damage. Experimental Materials—The six basic metals for this investigation were of commercial or higher purity, and the type 347 stainless steel was of commercial quality. These materials were supplied in various forms ranging from ingots to finished rods, and were fabricated to rods approximately % in. in diam and annealed for specimen stock. A summary of data pertinent to these materials is shown in Table I. The values for chemical compositions include both actual analytical values and typical values supplied by the manufacturer. More information concerning typical

Jan 1, 1957

By L. F. Mondolfo, B. E. Sundquist

The crystallographic orientation relationships resulting when lead is nucleated from the liquid by Ni, Cu, Ag, and Ge were determined. For each nucleating agent several definite orientatioz relationships were found. These relationships seemed to be controlled by good symmetry relations and low crystallographic disregistry between mating planes. For any given nucleating agent the under colling for nucleation was found fairly constant and independent of the orientation relationship and consequent disregistry. It was also found that, upon re melting and refreezing the Pb, the orientation relationship was changed. These findings prove that crystallographic disregistry is not the controlling factor in heterogeneous nucleation from the liquid. The results of this investigation tend to confirm the theory presented in a preceding paper that heterogeneous nucleation starts with the formation of an adsorbed layer of nucleated metal on the nucleat-ing impurity. Evidence is given that cavities in the nucleating agent act as centers of nucleation. IT has long been known' that solid extraneous particles are active in catalyzing phase transformations that occur in a system, particularly condensation and crystallization. It is well established that these heterogeneities act as catalysts by providing surfaces upon which nuclei of the precipitating phase can form with activation energies smaller than those required for homogeneous nucleation. Numerous investigations have shown that in this process of heterogeneous nucleation: a) the nucleus forms with one, or several, definite crystallographic orientation relationships with the nucleating phase2-4 and b) that there is a small range of undercoolings or super saturations characteristic of the nucleation of a given solid on a given Substrate.5-10 Turnbull and vonnegut11 have developed a theory based on theories developed by Volmer12 and Turn-bull and Fisher1= for heterogeneous nucleation from gases and liquids, that relates the super saturation or undercooling required for nucleation to the dis-registry between the lattices of the nucleus and the nucleating agent. This theory predicts that nucleation should occur with the orientation relationship between the nucleus and nucleating agent that minimizes the disregistry. Further, it predicts that the undercooling or super saturation necessary for nucleation should be a function of the disregistry. Numerous investigations have dealt with the orientation relationships resulting from the condensation of vapors onto crystalline solid substrates2,3 and a few with the nucleation of one phase by a second phase in solidification4,14. Others have dealt with the supersaturation8-10 and undercooling5-7 associated with nucleation in condensation and solidification respectively. However, there is virtually no report that gives both of these factors for the same system. In this investigation a study was made of the undercoolings and orientation relationships resulting when Pb is nucleated from the liquid by Ni, Cu, Ag, and Ge. It was the purpose of this investigation to check the Turnbull-Vonnegut theory, i.e., the importance of crystallographic disregistry between nucleating catalyst and nucleated metal. The results indicate that disregistry is not an important factor in nucleation and that the nucleation process is probably somewhat more complex than current theories suggest. EXPERMENTAL PROCEDURE Small single crystals of nickel, copper, silver, and germanium were prepared from materials of four to five nines purity, and the Pb used was also 99.999+ pet pure. Cu and Ag single crystals were prepared by sealing small chips of Cu or Ag in an evacuated quartz capsule and heating the capsule at 2000°F for 1 hr before cooling. Nickel crystals of 200 diam were also prepared in evacuated quartz capsules, but melting was done by heating the capsules in an oxy-acetylene flame for a few minutes. These spheres were invariably polycrystalline so

Jan 1, 1962

By Michael Perch, Charles C. Russell

Nearly 7 5 per cent of the total coke production in the United States in 1940 was consumed in blast furnaces. In 1939 the percentage was 69.9, and in 1938 it was 61.3. To produce a net ton of pig iron 1757 lb. of coke was required in 1940 and 1760 lb. in 1939. These figures indicate how dependent the production of pig iron is upon the production of coke. The rate of iron production is in some measure influenced by the physical and chemical characteristics of the coke. Blast-furnace operators believe that the physical properties of coke profoundly influence the operation of the furnace. Although it is true that coke of a wide variety of physical properties is used in American blast furnaces, the periodic fluctuation of these properties is one of the causes of irregularity of blast-furnace operation. The purpose of this paper is to present a broad picture of the physical properties of by-product coke that are generally considered to be important by coke-oven and blast-furnace operators. Effects of the kind of coal used, the preparation of the coal, the rate of coking, and other factors will be considered. Of all these variables, the kind of coal used is by far the most important. In this discussion use will be made of the method of coal classification by rank1 standardized by the American Society for Testing Materials. Although this method of classification has been an American standard for several years, it has not been given the attention it deserves, especially in connection with the selection of coal for production of coke. Despite the fact that many producers of blast-furnace coke are limited to some particular source or sources of coal, a good understanding of the principles involved in setting up the standard method of classification may lead to a better appreciation of the causes of changes in coke characteristics. Furthermore, where it is necessary to select new coals as a substitute for the original supply, this method of classification can be of great assistance. The data presented have been gathered from many sources, but no attempt has been made to cover the vast literature. Instead, some of the more important data have been selected to show how coals and their carbonization affect some of the physical properties of coke. It must be emphasized that generalizations concerning the behavior of coking coals are presented and that individual coals may vary widely from the specific behavior depicted. Nevertheless, it is believed that the data illustrate certain typical behaviors. Neither was it possible to cover completely all the factors involved; for example, the macroscopic constituents of coal are believed to have important effects on the physical properties of coke, but since there is little information available for such study, and since vitrain, clarain, and durain are neither

Jan 1, 1943

By L. A. Wilson, P. J. Root

The relative costs of heating a reservoir by steam injection and by combustion have been examined. The comparison was based on a model similar to that proposed by Chu.' The cost of boiler feed water, the price of fuel, pressure and plant capacity were parameters in determin-ing the costs of air compression and steam generation. The analyses compare the cost of heating to the same radius by the two methods. Results suggest that the two primary factors for comparison are the price of fuel and the amount of crude burned during underground combustion. The cost of fuel has a greater effect on the cost of heat from steam than it does on its cost by combustion. As a result, analyses indicate that when the price of fuel is low, steam may be unequivocally cheaper than air. The influence of heat loss is such, however, that as the heated radius increases combustion becomes relatively more competitive depending upon the amount of crude burned. This implies that steam may be cheaper for small stimulation jobs (huff and puff) but combustion may be more economically attractive for heating large areas (flooding). INTRODUCTION Use of thermal methods of recovery is an accepted fact today. After an induction period of several years, processes are being widely used that involve reservoir heating to augment recovery. Of the several techniques, steam injection and forward combustion appear to be destined to dominate the field. Although the objectives of both are the same, the basic differences between generating heat in situ and injecting heat after surface generation influence the cost in different ways. This study compares the cost of heating a reservoir either by steam injection or by forward combustion. There has been no consideration of recovery. Presumably, recovery from the swept region would be high in either case. The sole consideration was the cost of heating to the same radial distance by either process. PROCEDURE THE MODEL The basis for comparison was a mathematical model similar to that used by Chu' for combustion. The model simulates a radial heat wave in two-dimensional cylindricaI coordinates. It includes heat generation, conduction and convection within the reservoir and conduction in the bounding formations. Thus, heat losses from the formation are considered. Three significant modifications were made. 1. Equal logarithmic increments rather than equal increments were used for the mesh spacing in the r direction. By this technique large distances were simulated with relatively few mesh spaces. 2. A backward difference approximation to the convection term was used to avoid troublesome oscillations which result from a central difference approximation when the convection term is large. 3. The radial increments of the combustion zone motion were not necessarily uniquely related to the mesh configuration. The cumbersome step function introduced by the heat of vaporization of steam was circumvented by assuming the enthalpy of the steam to be a linear function of temperature between reservoir temperature and steam temperature. This is equivalent to assuming an average heat capacity numerically equal to the difference between the enthalpy of saturated steam and the enthalpy of water at reservoir temperature divided by the difference between the two temperatures. Heat losses obtained by this model are in essential agreement with those obtained by the analytical solution of Rubenshtein.' A detailed description of the model is presented in the Appendix. Using the model, the times required to heat to particular radial distances were obtained as a function of injection rate and other physical parameters. For the steam case, injected fluid was assumed to be saturated steam at pressures of either 500, 1,000 or 1,500 psia. The corresponding temperatures are 467, 544 and 596F, respectively. Thickness ranged from 10 to 50 ft and injection rate ranged from 100,000 to 1 million Ib/D. Reservoir and overburden temperatures at the injection well were assumed to be that of saturated steam at the injection pressure. The effect of maintaining the overburden temperature at the well at a different temperature (initial reservoir temperature) was examined with no significant change in behavior. The influence of wellbore heat losses for the steam case was determined in the following manner. The rates of heat loss as a function of time were estimated using an approach similar to that suggested by Ramey." he data were based on injection through 2%-in. tubing in 7-in. casing. Integration of these data over the entire iniection period yielded the total heat loss. Total heat losses were then corrected to their equivalents in steam (this number resulted from dividing the total heat loss by the latent heat). This was considered additional steam required to accomplish the reservoir heating and the total cost was increased accordingly.

Jan 1, 1967

By J. L. Lamon, W. Crafts

Study with the electron microscope of the carbides in vanadium-chromium-molybdenum steels after tempering up to 1000 hr at 600 teelsto 1400°F confirmed that alloy carbides are formed at the secondary hardening temperature by decomposition of the plate-like iron carbides. It was also demonstrated that vanadium carbide persists as much smaller particles than do chromium- or molybdenum-bearing carbides. Conditions conducive to the formation of fine vanadium carbides are indicated to be favorable for high temperature strength. IN order to determine the effects of long exposure at high temperatures on vanadium-bearing steels, a survey has been made of their hardness and carbide structure. The behavior of carbides in the tempering of martensite was studied by X ray diffraction and electron microscope examination of electrolytically extracted residues in greater detail than in an earlier investigation.' A group of steels with about 0.25 pct carbon and containing chromium up to 5 pct, molybdenum up to 1 pct, and vanadium up to 1 pct was either quenched or annealed and then tempered for peri- ods of up to 1000 hr at 600° to 1400°F. Their hardness after tempering agreed with the Hollomon and Jaffe2 relation of equivalency of time and temperature, and with the degree of secondary hardening predicted from composition. Further, the appearance of the carbides indicated that the time and temperature equivalency relation was also applicable to the degree of carbide development. The mechanism of the tempering of martensite was demonstrated more clearly than in the earlier study. It was confirmed that carbides develop from martensite as poorly defined plates of the Fe2C type carbide followed by thickening of the plates with a transition to Fe,C. Finally the plate structure deteriorates into a lacy mass from which alloy carbides emerge as chunky particles that grow slowly with further increase of tempering temperature. Vanadium carbide derived from tempered martensite was found in characteristically small particles that tended to grow very slowly. The addition of chromium or molybdenum to a steel with predominant vanadium carbide tended to introduce carbides of a chromium- or molybdenum-bearing type having a somewhat larger particle size. The Cr,C, type carbide particles were larger than those of the V,C, type and somewhat smaller than the carbides in steel containing both Cr,C and M,C. Similar observations were made of the carbides in the pear lite of annealed steels. It appeared that high temperature properties would be benefited by the retention of the fine carbide particles that result from a balance of composition and heat-treatment designed to produce a maximum amount of vanadium carbide. Procedure: The steels used in the investigation were made with a base of Armco iron in a high-frequency furnace at the Union Carbide and Carbon Research Labs., Inc. The steels were deoxidized

Jan 1, 1951

By Henry S. Rawdon

Any laboratory corrosion test, as judged from the practical point of view, is valuable only to the extent that it foretells what will, in all probability, occur in service. Such a test is most properly to be considered as a "pilot test," that is, a test which indicates the direction along which action may be expected to occur rather than as a truly quantitative test which would be expected to tell just how and to what extent the action would proceed. It is generally recognized that laboratory corrosion tests should be chosen with particular reference to the character of service expected for any particular type of metal, so far as it can be foreseen. Even when this requirement has been fulfilled, however, the question whether the actual service behavior of the material is in accordance and general agreement with predictions based upon such laboratory tests is always a pertinent one. The information available in the technical literature bearing on the correlation between the service behavior of metals from the corrosion standpoint, and the results obtained with the same metals in laboratory corrosion tests is very meager, indeed. The results which have been obtained in weather-exposure tests of sheet duralumin which form the body of this discussion are presented here for their bearing on this particular phase of the problem of the corrosion resistance of duralumin. Although the exposure tests described have not been completed, in the sense that all of the tests, in the series initially laid down, have been accomplished, still the general trend shown by the results is so clear that a number of definite conclusions at this stage (subject, of course, to possible modification in the light of later results) are believed to be warranted. The tests reported upon here form one phase of the much broader study of this subject which has been under way for several years in which the National Advisory Committee for Aeronautics, the Bureau of Aeronautics of the Navy Department, the Army Air Corps and the Bureau of Standards have cooperated. Without the very helpful cooperation of the manufacturers in furnishing the

Jan 1, 1929

By A. M. Gaudin

The study that is presented here was undertaken in order to condense information concerning comminution, and covering a great variety of conditions, into one or several rules which would be of use in the development of a systematic theory as well as in many directly practical ways. As the result of this work, the following conclusions appear justified: 1. Rocks may be classified, from the point of view of comminution, into two general classes which are (a) structurally homogeneous, and (b) structurally heterogenous. Structurally homogeneous rocks are those in which fracture takes place through grains and grain boundaries alike; heterogeneous rocks are those in which fracture passes in preference through grain boundaries. 2. If a sized product composed of structurally homogeneous rock grains is crushed, a product results in which the relation between the percentage weight of grains of various sizes and these sizes themselves follows a definite law. This is not true of structurally heterogeneous rocks. 3. Ball milling with structurally homogeneous rocks, and under certain conditions, presents exceptions to this rule. 4. In ball milling with structurally homogeneous rocks, there exists a critical ratio of size of feed to size of balls, above which the machine operates essentially by surface wear, and below which it operates essentially by breaking across the body of the particle. 5. In ball milling, with structurally homogeneous rocks, and when the size of feed grains exceeds the critical size, the particles worn off are of a substantially definite size which depends upon the ball size. 6. In the case of a typical heterogeneous rock, such as Manhattan schist, particles are crushed in such a way that there is a greater proportion of grains of the size that is the average grain-size of the rock than there would be in that range of size with a structurally homogeneous rock. This has been found to be true with all the crushers tested. 7. Different methods of crushing produce grains of different shapes. 8. The importance of sizing the — 200-mesh portion of a crushed product, in crushing-efficiency investigations, has been greatly under-

Jan 1, 1926

By AIME AIME

METALLIC corrosion, which results from the chemical affinity of different metals for non- metallic elements, should be considered from both the kinetic and static viewpoints. From the stand- point of statics the metals may be arranged in the order of their affinity for oxygen, chlorine or any other acid- forming element. They may also be arranged in the order of the magnitude of the heat of combination of their corresponding compounds. It is misleading to talk about some metals as "noble," because these relations are all relative; and the order varies for oxygen, chlorine or whatever the element may be. A third way to arrange the metals is by their solution pressures. These three methods indicate that one metal is better under one set of conditions, but not so good under other conditions. Considering the problem from the standpoint of kinetics, the thing which saves most metals is what may be called the sluggishness of reactions. Using organic substances as an example, we know they will all oxidize, but fortunately they do so rather slowly. An increase in temperature always means an increase in the reaction rate, and preventing corrosion at high temperatures is a greater problem than at low temperatures. A second consideration is to avoid all sub- stances which might provoke catalytic action, and as it is generally impossible to foresee what substances might do this, the thing is to avoid all substances other than the main constituents of the alloys. A third consideration is to avoid local electrolytic action, which again indicates the advisability of avoiding the contact of differing substances.

Jan 1, 1926

By C. W. Macgregor

The observation of the flow layers, or Luders' lines, produced in mild steel when it is stressed into the plastic range often provides considerable useful information for the study of the fundamental mechanism of the plastic flow of metals. It is a commonly observed fact that as soon as the upper yield point in a mild-st'eel tensile-test bar is passed, an unstable condition develops in the equilibrium, the load on the testing machine drops and if the surface of the bar contains a thin mill scale, the latter begins to flake off rapidly along certain "lines." These "lines" are ill reality traces of wedge-shaped flow layers and are formed by the inter-section of the surface of slip and the surface of the bar. The average plane of the flow layer itself has been found by various experimenters to be inclined at an angle of approximately 45" to the axis of the test bar. In a body of more complicated shape stressed in possibly a different man-ncr, the tangent planes to the flow layers at each point seem in many cases to be inclined at an angle of about 45" to the principal stress direct-tions at the point. As examples of the latter may be mentionecl the logarithmic spirals obtained when a rivet hole is punched in a thin plate, or when a tube is subject,ed to internal pressure only, etc. IIencc if the flow layers are observed from an experiment, the shear-st'ress trajectories —the curves indicating the direct,ions of the maximum shearing stresses in the body—may then be approximately determined. Since the latter curves form an orthogonal family inclined at 45" to the principal stress directions, the family of principal stress trajectories, or the curves irldicating the directions of the principal stresses, may be thus obtained Although the discontinuous type of stress-strain curve at the yield point is commonly observed with test bars of mild steel, more recent experiments have shown that this is by no means the only material exhibiting this interesting phenomenon. A similar effect has been observed in zinc and cadmium crystals, by Becker and Orowai~; in duralumin and other aluminum alloys, by Dawidenkow,~Elam,~ Fell4 an(l others; in copper and copper-alloy crystals, by Elam;~ in brass by Elam;3 in brass wires by deForest;" in higher carbon steels, tungsten steel, and

Jan 1, 1939

By R. P. Alger, C. A. Doh, M. P. Tixier

The principle, the equipment and field operation of sonic logging are described. The tfio-receiver system produces logs independent of hole size and mud. Field experience is given and forms the basis for the interpretation of the log. The derivaiion of porosity values from measured velocities is discussed, according to the type of formations (hard formations, compacted sands, and unconsolidated formations). The time-average equation proposed by M. R. J. Wyllie, A. R. Gregory and L. W. Gardner is uscd as a basis for the computation of porosity in limestones, cemented sandstones and compacted sands. Variations in the lithologic character of limestones do not seem to change the porosity calibration markedly. The compaction of sands is related to the compaction of shale adjacent to them; and, thus, the shale velocity is used for the establishtnent of empirical relations for the computation of porosity in un-consolidated formations. Various forrnu.las are tentatively presented to account for shale and fluid content. Field experience demonstrates that considerable attenuation of sonic energy takes place in unconsolidated formations, particularly when gas bearing, and in fractrured formations. Unusually large attenuation produces skipped cycles, a feature easily recognized. The application of sonic logging to structura1 studies is featured, showing its possible integration with the dipmeter. Correlation and its application to the irrterpretation of seisrmic surveys are reviewed. The paper is illustrated with field examples. Sonic logging is the recording of the time required for a sound wave to traverse a definite length of formation. Sonic travel-times are inversely proportional to the speed of sound in the various formations. The speed of sound in subsurface formations depends upon the elastic properties of the rock matrix, the porosity of the formations and their fluid content and pressure. Below the "weathered" or low-velocity layer extending from 50 to 100 ft or so below the surface, sound velocities may range from about 6,000 ft/sec in shallow shales to as much as 34,000 ft/sec in dolomites. In hard formations (well cemented and/or compacted), the sonic log reflects the amount of fluid in the formations; hence, it correlates well with their porosity. In unconsolidated formations, which are usually of fairly high porosity, the sonic log gives an approach to porosity determination, when its readings are corrected for lack of compaction, shaliness, and fluid content. In such formations the sonic log may also indicate the presence of gas and may distinguish between oil- and water-bearing beds. Field experience with the sonic log in soft formations is more limited than that in hard formations. As a result, interpretation in soft formations is not as well developed at the present time. In all types of formations the sonic log is of considerable value for correlation and for the more detailed and accurate interpretation of seismic data. EQUIPMENT AND PRINCIPLE FIELD OPERATION The basic features of the sonic log" are a two-receiver system and two available short spacings. The log is recorded on film using a standard field unit. An SP curve is run along with the sonic curve to give a more interpretable log and to establish absclute depth control for comparison with other logs run in the same well. If desired, a gamma-ray curve may be recorded simultaneously with the sonic curve. Fig. 1 shows the sonic-gamma ray combination sonde. The sonic portion consists of a sound transmitter and three receivers mounted 3, 4 and 6 ft from the transmitter. When the first and second receivers are used, a sonic log of I -ft spacing (distance between receivers) is obtainea. Use of the first and third receivers provides a 3-ft spacing. The transmitter emits pulses at the rate of l0/sec. After the transmission of a pulse the first arrival of sound energy at each receiver triggers its response system. The differ-