Search Documents

By W. M. Albrecht, M. W. Mallett

The solubilities of hydrogen in titanium and several of its alloys were determined at 600 to 1000°C and pressures of 0.05 to 10µ of mercury. Solubility increases with increasing beta phase in the alloys. Factors found to affect degassing rates are specimen size and presence of thick surficial oxide. Removal of hydrogen by heating in vacuum and in flowing inert atmospheres was studied. Practical curves predicting minimum degassing times are presented. THE presence of hydrogen in titanium and titanium alloys has detrimental effects on the mechanical properties of the metal.'"," The hydrogen content of commercial titanium is sometimes of the order of 200 ppm by weight' and varies with alloy composition. As a consequence, titanium and some titanium alloys as normally processed are sometimes not ductile unless treated to lower the hydrogen content. The best known hydrogen-removal treatment is heating the material in a vacuum. The rate of removal (degassing) at a give temperature determines the duration of the treatment required to attain a satisfactory low hydrogen level.

Jan 1, 1959

By Robert T. Hill

The successful completion, January 10,1901, by Capt. A. F. Lucas, of a well, near Beaumont, Texas, whereby an enormous flow, estimated at '75,000 barrels a day, was obtained, opened a new oil-field in the United States, kindled a frenzy of exploitation and speculation, revolutionized the fuel industry of a large region, and brought gain to thousands of people. Even to-day, it is impossible to cast up the present results or to prognosticate the future influence of this event. It has caused the revival of attention in other localities where oil had been suspected, and exploration for oil throughout the Texas region. It has attracted notice to the mineral resources of the Texas region, and created an interest in the geological conditions of that great State. This State, which has increased in population and wealth, as recorded by every succeeding census, with leaps and bounds such as are exhibited by no other part of the Union, now stands fifth in population and first in productive wealth per capita. Its fields, pastures, forests and mines teem with raw material. The whole economic evolution of the State has gravitated toward a focal point where these products were available for the coming of the kiln, the machine and the factory. The only drawback to the prosperity of the State was the lack of an economic fuel, inferior coal costing an average of $5.00 per ton at the time of the Beaumont discovery. This

Jan 1, 1903

By J. F. Kemp

PAGE Introductory Description of Deposits of this Type,.....244 Topography of the Ducktown Region,...247 Geology and Petrography,...248 The Mineralogy of the Ores and Gangue,..249 The older minerals : Amphibole, 250 ; Pyroxene, 250; Garnet, 251; Zoisite, 252; Calcite, 258 ; Quartz, 259 ; Apatite, 259 ; Rutile, 259. The Sulphides: Pyrite, 259; Zincblende, 259; Galena, 260; Pyrrho tite, 260; Chalcopyrite, 260. Later minerals, not belonging to the Gossan: Quartz, and certain sul phides, 261 ; Graphite, 261. The Formation of the Ore,...262 The Gossan Minerals,...........263 Bibliography,............265 Introductory Description of Deposits of this Type. Ore-bodies of more or less lenticular shape and lying parallel with the foliation of schists and slates form a group of

Jan 1, 1902

By L. D. Ricketts

' In recent years the metallurgical field of the copper industry has expanded greatly, the copper ores have become lean add diverse in charactcr, and we are obliged to treat such ores on a very large scale. On the commercial side, the operating and consulting staffs of the great mining companies have been enlarged and organized, and no great capital expenditure is decided upon until it has been investigated and recommended by a highly organized force of specialists as a committee. I believe that in the scientific field and in the most valuable proceedings of our -various societies the old idea of one-man point of view and one-man treatment of principle and detail together has been splendidly developed and should continue, but for the advancement of our art we should deliberately discuss subjects among ourselves in order to do away with the idiosyncrasies of the individual and to gain a composite view reprcscnting the best thoughts of many men. In the development of new ideas leading to the introduction of new methods, the societies could enlarge their present great field of usefulness if such discussion be had, and in my opinion further great good could be done if a number of men of different qualifications and experience would join in preparing a joint book, each dealing with his particular problem, but consulting the other men. In this way individualism would be preserved and various processes would be described, and if properly reviewed the paper would be palpably capable of analysis, and the student would have at his command the associated efforts of a group of qualified engineers. I have neither the time nor the qualifications to make an investigation and study in detail of hydro-metallurgical processes, but for some years I have foreseen the development of such processes, and I have a deep interest in the subject and have given some of its phases careful consideration from a long-distance viewpoint. I have assisted in directing many experiments and in reviewing the merits of many processes, and am glad to make some introductory remarks with the understanding that other gentlemen present will freely and candidly enter into the discussion and help to fill out the few bare bones that I can uncover.

Jan 1, 1916

By G. R. M. Del Giudice, A. F. Taggart, Othon A. Ziehl

In a previous paper1 in which one of the authors collaborated, it was postulated that All dissolved reagents which, in flotation pulps, either by action on the to-be-floated or on the not-to-be-floated particles affect their floatability, junction by reason of chemical reactions of well recognized types between the reagent and the particle affected. This generalization, apparently, like many pioneer structures, had for certain observers a flimsy appearance, and these, judging its stability rather by the number than by the character of its foundation posts, have attempted variously to overthrow it, either by the frontal attack of general denial, or by the flanking movement involved in assuming that those cases in which the facts were unknown or unproved were, therefore, discordant. But as time has passed and further evidence on the question has accumulated, it has become apparent that the results of verifiable experiments add stone by stone to the substructure of the hypothesis, and that the super-tructure has lost nothing in weathering. The present paper constitutes an examination of the opposing positions in the light of the more recent evidence developed. It will clarify the discussion if, at this point, we state more fully the implications of the disputed hypothesis. In the first place, it is explicitly limited to reagents that are dissolved in the water of the flotation pulp. Next, it refers only to such of these dissolved reagents as act on the solid particles in the pulp to affect their floatability. This includes the collectors, activators, and certain depressors and gangue-control reagrnts, but not the pure frothers, and not, necessarily, conditioners whose function seems to be merely that of pH control, although in certain cases it has been demonstrated that such control has the effect of regulating the primary reaction of the collector, depressor, or the like. Finally, there is no limitation as to the nature of the chemical reaction postulated.

Jan 1, 1935

By James S. Browning

For the past several years, USBM has conducted laboratory and continuous process development work on the weathered mica pegmatites ores of Alabama, Georgia, and North Carolina to determine the feasibility of recovering commercial-grade mica concentrates by flotation. The research has resulted in the development of two processes for flotation of mica: 1) an acid-cationic method for recovery of coarse mica and 2) an alkaline-anionic-cationic method for recovery of fine mica. The research indicated that the two processes may be effectively utilized separately or in combination for flotation of mica from weathered pegmatite ores. This report summarizes the process development work, and demonstrates the feasibility of producing commercial-grade concentrates with a high recovery of the contained mica. Mica mining in the United States is confined largely to pegmatites and schists in a few well-defined areas. The largest region extends from central Virginia southward through western North and South Carolina, northern Georgia, and east-central Alabama.'" Whereas in western North Carolina, these pegmatite dikes are weathered to only a shallow depth, they are deeply weathered in the Carolina Piedmont and in Georgia and Alabama. Particularly in Georgia and Alabama, mica is found in the decomposed slates and schists adjacent to the pegmatites, and in deeply weathered granites. Most flake mica is obtained as the major marketable product by crushing and milling pegmatites4 To a lesser extent, mica is produced as a byproduct of feldspar" and spodumene. Past research by U.S. Bureau of Mines (USBM) has developed two methods for mica flotation. One method utilizes acid-cationic flotation for recovery of mica.' This method requires thorough desliming of the ore with consequent fine mica losses. The other utilizes an alkaline-anionic-cationic process for recovering fine-size mica from pegmatite ores after desliming sufficiently to remove clay materials but not so drastically as to remove the fine mica.8-18 The latter process has also been successfully applied to a micaceous schist ore from California.' This report summarizes the results of these research studies. Both of the flotation processes developed by USBM have been adopted by the mica industry and are being commercially utilized separately and in combination for flotation of mica from weathered pegmatite ores. Description of Ores The weathered mica pegmatite ores used in the investigations were obtained from commercial mica operations in Alabama, Georgia, and North Carolina. The

Jan 1, 1971

By C. O. Fairchild

THE meaning of temperature control can be extended to cover not only the control of temperatures' but also the control of processes through a knowledge of the temperatures involved. In this sense it has a very wide interest. A list of the industries in which temperature control is used in one way or another would cover nearly the entire industrial field. This discussion will be confined to the field of high temperatures. In practically all industries involving operations at high temperatures, pyrometers are used or men are paid for their ability either to estimate temperatures or gage an operation by some physical or chemical change or condition dependent on temperatures. As progress is made in the development of instruments and of methods for measuring temperature, some of these highly skilled artisans are learning the use of a new tool. Many processes have been, in recent years, improved by means of exact measurement thus substituted for estimation, but in a great many industries the pyrometer has had practically no opportunity to demonstrate its usefulness. The perfecting of instruments must be accompanied with a dissemination of the knowledge that new instruments are available and can be economically used. The demand at present, however, is ahead of the supply, and many industries are handicapped by the want of pyrometers. One of the highest paid skilled tradesmen of the present time is the man in the steel rolling mill who knows when proper working temperatures are attained. The metallurgist in his development of steels is continually demanding closer adherence to given temperature ranges in the processes, and the pyrometer is rapidly becoming indispensable. Properties of the finished products are being correlated with working temperatures and so closely that in some cases even the pyrometer is taxed to give the required accuracy. The greatest progress has been made in those industries in which the lower temperatures are used, particularly below 500° C. In this lower range automatic control has been highly developed.

Jan 9, 1919

By Samuel S. Wyer

The art of natural-gas compressing is now over 25 years old, and has grown at practically the same rate as the increase in domestic natural-gas consumers. There are now over 200 natural-gas compressing stations in North America, aggregating more than 320,000 hp. of compressor capacity and representing a property value of more than $22,000,000, and compressing more than 85 per cent. of all the gas used. The age and magnitude of the art make it evident that the use of gas compressors is a recognized integral part and universal custom of the natural-gas business. The public also is not without its rights and vital interests in this problem. Approximately 1,700,000 domestic natural-gas consumers in North America are dependent upon gas compressors for their natural-gas service. That is, if the use of compressors were to be prohibited, the majority of these consumers would be unable to secure adequate natural-gas service. Each consumer represents between four and five persons, and it therefore follows that the comfort and well-being—as far as natural-gas service is concerned—of at least 8,000,000 persons would be affected if the use of natural-gas compressors should be prohibited. These 1,700,000 consumers have invested, in services, house piping, fixtures, and appliances, an average of about $90 each, or an aggregate of $153,000,000, which is much more than the companies' investment in gas compressors. Furthermore, in all cases where the rate paid by the consumers is fair to the gas company—considering the value of the service rendered by the gas company—the consumers are entitled to continued service and protection of the investment they have made on the faith that the gas service would be continued in the future. Since "Customs adopted and acquiesced in, if not in conflict with federal or State legislation, have the force of positive law,"l and ('Courts will take notice of whatever ought to be generally known withxn the limits of their jurisdiction,"2 there ought to be no question as to the un-

Jan 1, 1916

By Lester C. Uren

Petroleum occurs, in nature, as a fluid saturating the pore spaces between the grains of porous rocks or aggregations of rock particles such as sand, sandstone, conglomerate, shale, limestone, etc. The oil, under the influence of gas pressure, hydrostatic pressure, gravity, earth pressure, and, perhaps, other natural forces, is caused to flow through the porous "reservoir rock1' into wells penetrating the stratum in which the oil occurs. The principal moving force is the pressure of dissolved or occluded natural gas within the oil, though this force is assisted by gravity and by the hydrostatic or buoyant pressure of ground water about the edges of the "pool." The wells, providing outlets to the surface, are centers of reduced pressure and the flow of rock fluids into a particular well is usually an expression of the difference in pressure existing between the space within the well and that of the stored oil within the reservoir rock. The greater this differential pressure, the more rapidly will oil flow from the source rock into the well. Opposing movement of the oil from the reservoir rock into the well are certain natural forces related to the rock structure, such as pore friction and capillarity, and certain others related to the physical properties of the oil, such as viscosity and adhesion. The differential pressure between the well and the boundaries of the area drained by it must be sufficient to overcome the forces opposing flow if there is to be movement of oil into the well. If by any device the resistance to movement of the oil may be reduced, the oil will flow into the well at a more rapid rate and the effective area of drainage will be increased.

Jan 1, 1925

NORTH AMERICA ALASKA Anchorage,-Ames, M. B. Culver, H. W. Fiedler, H. L. Fox, E. F. Gallemore, W. A. Kreitlow, E. J. Layfield, R. A. Saarela, L. H. Strandberg. H. Candle,-Bobbins, J. S. College.-Fackler, W. C. Joesting, H. R. Swift. R. E. "Wilcox, H. G.. Crooked Creek-Lyman. R. F. Fairbanks.-Beistline, E. H. CANADA Canadian Army Overseas,¬ Ball, H. D. Brides, C. Butterill. H. J. M. Ladner, F. E. Lane, H. C. Millar, R'. A. Murchison, R. G. Passow, F. M. ALBERTA Calgary-Allen, R. E. de Hart. J. B. Dingman, C. W. Furnical. G. H. Gray, J. G.

Jan 1, 1943

MINING AND METALLURGICAL SOCIETY OF AMERICA San Francisco Section The San Francisco Section of the Mining and Metallurgical Society of America held a joint meeting with the local section of the American Institute of Mining Engineers at the Engineers' Club, San Francisco, on Tuesday, Apr. 16, 1918. The meeting was preceded by a dinner. Letters from the parent body in NewYork asking for the consideration of the proposed bill before Congress, and an expression of opinion relative to the appointment of a Federal Administrator of Mines justified the joint meeting of the local sections of the two mining societies, in that a more representative opinion of the engineers of California could he obtained. The meeting was called to order at 7:15 P.M. by Mr. Frank H. Probert acting as Chairman. About thirty engineers were present. Mr. Probert read a letter of March 14, from Secretary Huntoon, asking that the meeting be called. He read excerpts from Bulletin 117 of February 28, 1918, of the Mining and Metallurgical Society containing a copy of the proposed bill, so that all present might be advised of its essential contents. He briefly commented on the urgent need of such legislation and invited discussion of the subject. After long and thorough discussion on the part of the members present, Professor Lawson made the following motion: I move that a resolution expressing the sense of the joint meeting of the local sections of the American Institute of Mining Engineers and Mining and Metallurgical Society of America be forwarded to the secretaries of the two societies to the effect that we heartily approve of the purpose and intention of the bill designed to promote and stimulate the production of minerals necessary for the successful prosecution of the war; and that we suggest prices should be fixed for the period of the war and two years thereafter, and that these prices, guaranteed by the Government, should apply at the nearest shipping point to place of production of the minerals. This motion was carried. The meeting then adjourned, and a telegram was sent by Mr. Probert, the Chairman, to Mr. Huntoon, notifying him of the motion that had been carried at the meeting.

Jan 7, 1918

By Ira B. Joralemon

Neighboring mines, like men who live in the same environment, often assume similar characteristics. In the Bridge River area of the Lillooet district in central British Columbia there is a remarkable exception to this rule. The Pioneer mine has a simple fissure over 3000 ft. long, with no faults of more than a few feet and with only minor variations in width; the Bralorne mine, 2½ miles away at the other end of the same intrusion, has developed one of the most intricate vein and fault systems in the West. Hinged faults displace the main vein for hundreds of feet, and sometimes become valuable veins themselves. The width of ore varies in a few yards from 2 to 60 ft. Changes in grade of ore are just as abrupt. The rocks that follow the veins or are cut by them often grade into one another or into the ore with no definite contacts. Although the complexity of the structure has left many problems unsolved, the development has indicated a fascinating geological pattern. The Bralorne is in the eastern portion of the Coast Range, 55 miles by spectacular mountain road from the Pacific Great Eastern Railway station of Bridge River. The adit tunnel runs easterly from Cadwallader Creek, a tributary of Bridge River that flows into the Fraser River. Steep mountains rise from 3300 ft. elevation above sea level at the creek to peaks and ridges at 8000 to 9000 ft. altitude. The lower slopes are heavily wooded while above 5000 ft. bare rocks, glaciers and snow-fields extend far above timber line. See Fig. 1. Story of the Bralorne The Lorne claim, staked in 1897, was one of the earliest lode locations in the Bridge River district. At that time it was 70 miles by steep and treacherous trail from the railway. For the next 15 years Arthur Noel, Will Haylmore and other local prospectors mined the small, irregular, oxidized quartz veins to a maximum depth of 200 ft., and treated the ore in arrastres and later a five-stamp mill. The total production to 1912 was only $55,000. Noel and associates later formed the Lorne Amalgamated Mines Co., which they worked in a desultory way until 1925. Increasing sulfide and arsenide content in the veins

Jan 1, 1935

By Ira B. Joralemon

Neighboring mines, like men who live in the same environment, often assume similar characteristics. In the Bridge River area of the Lillooet district in central British Columbia there is a remarkable exception to this rule. The Pioneer mine has a simple fissure over 3000 ft. long, with no faults of more than a few feet and with only minor variations in width; the Bralorne mine, 2½ miles away at the other end of the same intrusion, has developed one of the most intricate vein and fault systems in the West. Hinged faults displace the main vein for hundreds of feet, and sometimes become valuable veins themselves. The width of ore varies in a few yards from 2 to 60 ft. Changes in grade of ore are just as abrupt. The rocks that follow the veins or are cut by them often grade into one another or into the ore with no definite contacts. Although the complexity of the structure has left many problems unsolved, the development has indicated a fascinating geological pattern. The Bralorne is in the eastern portion of the Coast Range, 55 miles by spectacular mountain road from the Pacific Great Eastern Railway station of Bridge River. The adit tunnel runs easterly from Cadwallader Creek, a tributary of Bridge River that flows into the Fraser River. Steep mountains rise from 3300 ft. elevation above sea level at the creek to peaks and ridges at 8000 to 9000 ft. altitude. The lower slopes are heavily wooded while above 5000 ft. bare rocks, glaciers and snow-fields extend far above timber line. See Fig. 1. Story of the Bralorne The Lorne claim, staked in 1897, was one of the earliest lode locations in the Bridge River district. At that time it was 70 miles by steep and treacherous trail from the railway. For the next 15 years Arthur Noel, Will Haylmore and other local prospectors mined the small, irregular, oxidized quartz veins to a maximum depth of 200 ft., and treated the ore in arrastres and later a five-stamp mill. The total production to 1912 was only $55,000. Noel and associates later formed the Lorne Amalgamated Mines Co., which they worked in a desultory way until 1925. Increasing sulfide and arsenide content in the veins

Jan 1, 1935

Neighboring mines, like men who live in the same environment, often assume similar characteristics. In the Bridge River area of the Lillooet district in central British Columbia there is a remarkable exception to this rule. The Pioneer mine has a simple fissure over 3000 ft. long, with no faults of more than a few feet and with only minor variations in width; the Bralorne mine, 2½ miles away at the other end of the same intrusion, has developed one of the most intricate vein and fault systems in the West. Hinged faults displace the main vein for hundreds of feet, and sometimes become valuable veins themselves. The width of ore varies in a few yards from 2 to 60 ft. Changes in grade of ore are just as abrupt. The rocks that follow the veins or are cut by them often grade into one another or into the ore with no definite contacts. Although the complexity of the structure has left many problems unsolved, the development has indicated a fascinating geological pattern. The Bralorne is in the eastern portion of the Coast Range, 55 miles by spectacular mountain road from the Pacific Great Eastern Railway station of Bridge River. The adit tunnel runs easterly from Cadwallader Creek, a tributary of Bridge River that flows into the Fraser River. Steep mountains rise from 3300 ft. elevation above sea level at the creek to peaks and ridges at 8000 to 9000 ft. altitude. The lower slopes are heavily wooded while above 5000 ft. bare rocks, glaciers and snow-fields extend far above timber line. See Fig. 1. Story of the Bralorne The Lorne claim, staked in 1897, was one of the earliest lode locations in the Bridge River district. At that time it was 70 miles by steep and treacherous trail from the railway. For the next 15 years Arthur Noel, Will Haylmore and other local prospectors mined the small, irregular, oxidized quartz veins to a maximum depth of 200 ft., and treated the ore in arrastres and later a five-stamp mill. The total production to 1912 was only $55,000. Noel and associates later formed the Lorne Amalgamated Mines Co., which they worked in a desultory way until 1925. Increasing sulfide and arsenide content in the veins

Jan 1, 1935

By Francis H. Crockard

During the past five years we have probably witnessed greater technological advances than in any similar period. Industry and science have steadily marched ahead. The makers of iron and steel products have watched with great interest the development of streamlined trains, faster and safer airplanes, the entirely new science of air-conditioning and the widespread use of stainless steels. Since 1930, we have witnessed the erection of the world's largest suspension bridge, the largest and fastest ocean liner and the spectacular Boulder Dam, while even greater things are planned in these particular fields. Other industries, too, have been moving ahead rapidly. This advance in a few years has been caused primarily by the fierce competition of the depression. Now, more than ever, is the emphasis placed upon quality and service. Makers of southern merchant pig iron have been no exception and have been confronted with increasingly strict chemical specifications and with much greater stress on physical characteristics than ever before. For example, sulfur in the iron must be held very low, competition demanding that it be in the 0.020's and low 0.030's; silicon content must be held within a very narrow range, and definite requirements of phosphorus and manganese are an essential part of the specifications. Physical characteristics are becoming of increasingly greater importance. The introduction of triple-skimmed, slow-cooled iron several years ago was the first step in this direction. Now there are a few customers who buy iron by chemical analysis and physical appearance, having found that the analysis alone is an insufficient guide to their requirements. In addition to questions of quality, the subject of cost has greatly altered the southern furnaceman's viewpoint on many things. Formerly we had low-grade but cheap raw materials, but recent developments, such as greatly increased labor rates, have raised the cost of the same

Jan 1, 1936

By H. M. Ziesemer, George Mieyr

Prior to 1909 that mountain of porphyry known as Sacramento Hill had hardly been touched though it had always been thought to contain ore. During that year, exploratory work was started by underground methods; drifting and raising continued until 1913. It was proved that a mineralized zone existed, the limits of which had not been determined ; so, because of the lower costs of exploratory work and the greater desirability of vertical sections, it was decided to prove the extent of the ore zone by churn drills. Drilling continued until 1917, when it seemed almost certain that the horizontal limits of the orebodies had been determined. Ore continued in depth in one direction beyond a point where it was economical to explore by churn drilling; this extension is still being developed by underground methods. The irregularities of the boundaries of the ore zones, together with the variable grades of ore encountered, made it necessary to drill on the corners of 100-ft. squares. Two ore zones were proved, known as the East and West Orebodies. The Sacramento Hill porphyry stock intruded into the Dividend fault. The fault ran roughly east and west with a dip to the south, having pre-Cambrian schists on the north against Paleozoic limestone on the south. This intrusion was accompanied by a silica breccia on the south periphery, along the limestone contact side. The ore lay in the silica breccia and in the porphyry, some distance from the breccia. NO ore was found in the heart of the porphyry mass on the north side, along the schist contact. The West Orebody is elliptic in shape, having a major axis of 1200 ft. (366 m.) and a minor axis of 800 ft. (244 m.); these diminish with depth until, at 300 ft., the axes are 500 ft. and 300 ft., respectively. The ore consists of chalcocite, some bornite, chalcopyrite, and considerable pyrite in a siliceous gangue. About 30 per cent. of the copper is caused by

Jan 1, 1923

By J. Charles Miller

Natural carbon dioxide has recently been exploited in the United States in consequence of oil and gas developments in the Western States and the growing demand by transcontinental and transoceanic shippers for solid carbon dioxidc. The discovery by drilling of commercial deposits resulted in consideration of its geographic and geologic distribution and occurrence. Its wide distribution in nature is evidenced by its occurrence in the atmosphere, hydrosphere and lithosphere. The question of origin of carbon dioxide involves consideration of theories similar to those concerning natural hydrocarbons, although available evidence favors an inorganic rather than an organic source. Areas favorable to development of commercia1 production appear to be those in proximity to igneous rocks or in the vicinity of decadent volcanic activity, where, it has long been known, the gas is evolved either free or dissolved in the waters of fumaroles, geysers or mud pots. Structure contour maps are presented showing the Wagon Mound anticline in New Mexico and the Farnham anticline, Utah. A well drilled on the latter supplies gas to a 20-ton plant manufacturing solid carbon dioxide at Wellington, Utah, on the Denver and Rio Grande R.R., whence it is shipped to surrounding territory and to the West Coast. Before funds are invested in a plant for the manufacture of liquid or solid carbon dioxide, whether supplied by wells or springs, an effort to ascertain the volume of gas available is advisable. The use of present methods of estimation of gas reserves with modifications to account for the quantity absorbed by any water present in the producing formation is recommended. The Farnham anticline is used as an example and computations are made of the probable volume of gas originally present in the structure. No attempt was made to compute reserves in the Niland area, California, for the reason that in such areas it is believed the volume is indeterminate. Introduction Carbon dioxide, in liquid and solid form, has found a wide variety of uses other than its primary application in carbonating beverages. It is now used in more than 40 different ways, ranging from cooling or freezing to use in gas or liquid form for mechanical purposes, chemical industry, explosive, fire extinction, and tire manufacturing. Undoubtedly the chief supply of carbon dioxide is obtained from industrial plants or artificial sources and until recently natural deposits of the gas have received little consideration. Few will question the utility and perhaps dependability of artificial sources, which possess the advantage over

Jan 1, 1941

By James O. Lewis

Gravity drainage is the self-propulsion of oil downward in the reservoir rock. Under favorable natural and operational conditions, it has been found to effect recoveries comparable to water displacement. With modern technical knowledge, the operator can often make a choice between dissolved gas drive, water drive and gravity drainage as the principal recovery agent in a reservoir. It is desirable that the opeator be able to determine which of the three agents will be most effective under each set of conditions. So far, gravity drainage has received less consideration than the other two. In this paper. an endeavor is made to set forth some of the principles of gravity drainage, to point out the types of reservoirs favorable for it, and to show how it may be applied in them. Field examples are described and discussed. Introduction Since early in the history of the oil industry, it has been recognized that gravity is one of the three important natural forces for expelling oil from the reservoir rock. As knowledge of the technology of oil recovery progressed, ideas changed with respect to the relative importance of the three forces and with respect to the manners in which they functioned. For a time, disproportionate emphasis was placed on the importance and function of gas and the need for conserving gas pressures. More recently, disproportionate emphasis has been placed on encroaching edge water. Only lately has there been evidence that the function and importance of gravity was to receive due consideration. Study of this neglected phase of oil recovery is needed to round out our knowledge of reservoir behaviors and to gain a balanced viewpoint of the interplay of forces that may operate in varying importance in reservoirs. The purpose of this paper is to discuss mainly in a qualitative way, the functions of gravity, to present some concrete instances where it has been important and to raise some questions that should be investigated further. Oil-recovery Agents The important natural agents for effecting oil recovery that may be originally available in a reservoir are gas, both dissolved in the oil and free in gas caps, encroaching edge water and gravity. Each of these agents can act in a dual capacity—physically to overcome the surface energies that hold the oil within the pores and mechanically to overcome viscous . resistance and to propel the oil through the porous reservoir rock to the wells. Advancing edge water displaces the oil from the pores and lifts it updip to structurally lower wells. Gravity drains the oil from the pores and flows it downdip to the wells. Gas displaces oil from the pores, entrains it in the gas stream and flows it to the wells, but gas in solution also affects the physical properties of the oil and thus can influence oil recovery by the other agents, whether or not the mechanical energy in the gas is utilized. Of the two functions of these agents, the more important is the ability to dis-

Jan 1, 1944

By Michael Tenenbaum, C. C. Brown

Numerous investigatiolls have been carried out to determine the total oxygen present in the basic open-hearth bath and the results of these studies have clearly defined the factors controlling the bath oxidation during the period prior to deoxidation. On the other hand, very little is known concerning any changes in total oxygen content that may occur during deoxidation, tapping and teeming. The need for such additional data is continually becoming more apparent, since there is no strict technical basis for selecting any particular deoxidation practice. Many steels are made for the same purposes and to the same chemical analyses by widely differing practices. Apparently, each practice is satisfactory. However, it would be desirable to establish more definitely the effects and relative merits of the individual practices. Such information could be used to give a definite foundation for evaluating various types of deoxidation. In order to approach this problem, a study was made of the changes effected in the total oxygen content of several grades of steel by representative open-hearth deoxidation practices. To carry out such studies, it was necessary that a reliable testing procedure for determining the oxygen content of the steel bath and the ingot mold be established. Before entering on any extensive testing program, consideration was given to the available methods of obtaining steel samples and analyzing for oxygen. Testing Procedures It has been shown5-9 that in solidified steel oxygen may ekist in combination with iron, manganese, silicon, aluminum, titanium, chromium and carbon, depending upon the amount of these elements in the sample. In molten steel, however, there has been no direct distinction of the various oxides. Accordingly, the total active oxygen in the molten steel bath is designated by the symbol 0. During deoxidation, various oxides may be present either in solution in the molten steel or as solid or liquid inclusions. Any sample taken from the molten steel for oxygen analysis will include both the dissolved and the mechanically included oxygen. Similarly, samples of the solid steel product will also include the two forms of Oxygen' Methods of Samplirzg the Molten Steel Bath In order to obtain a true oxygen analysis from liquid steel, this element must be completely retained in the solidified sample. Several methods have been proposed whereby this stabilization can be effected. As early as 1915, Kichlinelo proposed a method for testing molten steel, in which the oxygen combined with some added aluminum. The concentration of the resultant aluminum oxide was determined by chemical analysis. This method was

Jan 1, 1945

By W. Crafts, J. L. Lamont

Selection of an alloy steel for a heat-treated article has been facilitated by methods for the calculation of harden-ability,' as-quenched hardness and tempered tensile strength.2 Ductility and toughness may also be estimated if the steel is completely hardened on quenching, 5,6 and the present study was carried out in order to develop a basis for estimating the Izod impact strength of partially hardened steel. The investigation was directed toward the prediction of Izod impact strength in steels of normal commercial quality without consideration of special compositions or heat-treatments that might produce abnormal brittleness. It was found that Izod impact strength of alloy steel is controlled by hardness, degree of hardening on quenching, and grain size. In finegrained steels the impact strength for any given degree of hardening is inversely proportional to the tempered Rockwell C hardness, and the relation of impact strength to hardness is lowered by incomplete hardening. Calculation of the tensile strength and impact strength of heat-treating steels has shown that, except at very high strengths, tensile strength is raised by alloys without loss of impact strength whereas the tensile strength gained by higher carbon contents tends to be accom- panied by a disproportionate loss of toughness. Plain carbon steels give relatively low and unpredictable impact strength. The calculation is sufficiently accurate to be helpful in the selection of alloy steel, and common grades of alloy steel have been evaluated with respect to combinations of tensile strength and impact strength attainable after heat-treatment in sections from I to. 4 in. in diameter. Procedure The study of the relation of hardness to impact strength was based on test data derived from 24 heats from four producers. The steels included the following SAE and AISI compositions: 1020, 1030, 1040, 1340, 3310, 33167 4320, 43.30, 4340, 8620, 8630, 8640, 8720, 8730, 8740, 931°, 9317, 9440, 9917 and three high-alloy chromium-nickel-molybdenum steels. As far as is known, the steels tested were of normal commercial quality. They were supplied in 4-in. sections, which were forged to smaller sizes, prenormalized, and machined to final dimensions. Heat-treatment was carried out by heating to the usual austenitizing temperature for the grade of steel, holding for one hour per inch of thickness and quenching in still oil at room temperature. Previous work had indicated that this quenching treatment approximates a severity of H = 0.3; The bars were tempered as follows: 34 in., I in., and 1% in., 2 hr; 235 in., 3 hr; 4 in., ; hr. All bars were air-cooled from the tempering tem-

Jan 1, 1948