Search Documents

By C. E. Wood, E. P. Barrett, T. L. Joseph

The United States Bureau of Mines has been studying the blastfurnace process for about ten years. An experimental furnace was developed by the Burcau in cooperation with the Minnesota School of Mines Experiment Station, University of Minnesota. Many data have been obtained and published.' Royster, Joseph and Kinney §(48) found that the particle size of ore had an important effect upon the blast-furnace process. Kinne(28) stated: Economy in blast-furnace practice depends largely upon efficient gas-solid contact in the shaft of the furnace. If efficient work is not done in the shaft, the hearth and bosh will not function properly. A condition may be readily imagined where the particles of ore in the shaft are so large that the time entailed in the descent of these materials into the bosh is not sufficient to permit proper reduction and preparation prior to the time the ore enters the bosh of the furnace. Another condition may be pictured where the density of theatock column and the flow of stock is such that the ore will take one course and the gas another. Both of these examples will result in insufficient contact between the gas and the ore. Unreduced ore will reach the hearth, and the gas which has not been efficiently oxidized will reach the stock line. The result is the use of an excess of carbon in the smelting process. It is obvious that fine ore particles occurring in the ore as charged, or formed in the furnace due to heat and mechanical action, place a definite limitation upon the efficiency of the operation. There is also an economic loss of fine material as dust. Effect of Size of Material Kinney reported (p. 83(29)) the reduction of iron oxides between planes at three furnaces as given in Table 1. The Chicago furnace was operated on Lake ores. Distribution of gas was not good and much of the charge passed into the hearth before the iron oxide was reduced. The Holt furnace was operated on coarse ore. Distribution of gas was fairly uni-

Jan 1, 1930

By D. H. Gieskieng

Published tables of jaw crusher capacities are compiled for the most part from field performance data, interspersed with interpolations, extrapolations, various safety factors, and other modifications. Such a table attempts to balance and equalize field data from widely Werent materials, with differences of crushability, efficiency of feeding, sizing of the feed, and so on. The tests described in this paper were undertaken with the objectives of checking previously reported capacities; of studying the effects of various factors upon the capacity, including jaw plate curvature; and, if possible, of deriving a general capacity equation. Such an equation has been derived from the data obtained in these tests. It is given together with factors for its use. While more accuracy than is usually required may be obtained by careful application of the equation, it is of simple form and provides a convenient reference plane upon which the potential capacity of various crushers may be compared, and with which operating adjustments may be made on existing installations. The principal deviation in these tests from the usual approach consists of a laboratory technique which has been developed for the production of selected capacity data. Recording instruments are connected to crushers in such a manner that a continuous record is produced which discloses the inherent maximum capacity of the crusher and shows capacity decreases caused by hangups. The capacity effects of various crushing conditions are made more evident by this arrangement. The recording instruments were first applied to a standard sized 10 by 7 in. Blake-type jaw crusher in the laboratory. Suficient tests were run on this with various combinations of setting, throw, speed, feed sizing, shapes of jaw plates, and other operating features, to establish the individual effect of each on the capacity. The instruments later were applied to much larger crushers in the field, through the excellent cooperation of the managements in the Mesabi Iron Range, and data were obtained which closely corroborated the established trends. The capacity equation resulting from the test work is made up of a series of factors, each representing the contributing effects of setting, speed, width of chamber, nip angle, feed density, type of jaw plates, stroke, and the overall operating technique. Fortunately, most of these factors were revealed to be in direct proportion to the capacity for straight plate chambers. This equation is also applicable to chambers using curved plates, with slight modifications resulting from the capacity limitation of the upper portion of the crushing chamber. The equation has been derived from tests covering a very wide range of feed density and hardness. It has been found valid, providing that the feed material is either nonpacking in character, as is usual, or allowance in designing the crushing chamber shape has been made to accommodate this characteristic. Preliminary investigation has shown that the equation is also applicable to single-toggle jaw crushers. Conditions of this are that the top of the flywheel rotate towards the top of the crusher opening, and that the horizontal motion of the swing jaw relative to the stationary jaw at the discharge opening be considered as the stroke. The relatively large upper chamber jaw motion would probably result in realiza-

Jan 1, 1950

By S. P. Kinney, G. St. J. Perrot

Consumers of metallurgical coke are agreed that the quality of their fuel plays an important part in the performance of the furnace. Less unanimous agreement is evident when the properties of a desirable coke are discussed or when consideration is made of suitable testing methods by which the worth of a coke for metallurgical purposes may be determined quantitatively. Much has been written of the importance of combustibility as a factor in determining the performance of coke in the blast furnace and it is generally believed that cokes vary widely in this respect. The usual operating data of the furnace afford little evidence as to the combustibility of the fuel. As a part of a general investigation of the properties of metallurgical coke, the Bureau of Mines has explored the hearth combustion zone in a number of blast furnaces by means of water-cooled gas sampling tubes driven into the hearth through the tuyeres. The attempt has been made to determine the difference in combustibility of cokes varying widely in physical properties. Data have also been obtained in an experimental combustion furnace at the Bureau laboratories in Pittsburgh. This paper gives the results of experiments, made at eleven blast furnaces, in which the composition of the gases was determined at various points in the hearth in the plane of the tuyeres. Further work is in progress in which the zone above the tuyeres will be explored. Factors Affecting Coke Combustibility Brassertl has defined combustibility as the rate of progression of combustion, or, in other words, the speed at which the carbon molecules

Jan 1, 1923

By J. O. Lewis, Carl H. Beal

Introduction ............................... 492 Theories Relating to the Recovery of Oil.................. 493 Methods Commonly Employed for the Estimation of Future Production..... 495 Saturation Method........................... 495 Production Curve Method....................... 496 Production per Acre Method.....................: 496 Appraisal Curves.............................. 498 Derivation and Construction...................... 498 Comparison of Appraisal Curves of the Osage and Nowata Fields...... 505 Use of Appraisal Curves........................ 506 Accuracy of the Apprais?l Curves and Their Sources of Error........ 508 Relation Between Future Productions of Wells of Equal Output....... 510 Use of Appraisal Curves for the Derivation of Generalized Future Decline Curves. 513 Theory of Generalized Curves Showing the Decline in Production...... 513 Suggested Methods for Making Closer Estimates.............. 517 Use of Logarithmic Coordinate Paper.................... 518 Summary................................ 520 Introduction Oil wells usually reach their maximum daily output shortly after they are completed. From that time they decline in production, the rapidity of decline depending on the output of the wells and on other factork governing their productivity. The production curve of a well shows the amount of oil produced per unit of time for several consecutive periods; if the conditions affecting the rate of production are not changed by outside influences, the curve will be fairly regular, and, if projected, will furnish useful knowledge as to the future production of the well. By the aid of this knowledge the value of a property maybe judged, and proper depletion and depreciation charges may be made on' the books of the

Jan 1, 1918

By T. W. Guy

IN approaching the problems of sampling coal, a brief statement of certain facts that are more or less taken for granted may he helpful: 1. The coal-mine operator needs reliable data as to the physical and chemical characteristics of his coal in order to plan and control intelligently its mining, preparation, and marketing. The consumer needs such data in order to select the equipment and the coal best suited to meet his requirements, to check the quality of fuel delivered, and the efficiency of its use. Various government control agencies require such data as a basis for classifications and establishment of limits, for use in carrying out the requirements of federal, state or municipal laws. 2. All such data must be obtained by analyses, measurements, or tests made on samples, which are taken to represent the coal tested. It is now becoming generally recognized that, in accordance with statistical laws, test results from samples are not expected to represent the exact qualities of the lot or lots from which they are taken, except within statistical, or "expected" limits. Such limits are definitely specified by some present standards of the American Society for Testing Materials and the British Standards Institution. 3. Samples that give ash within satisfactory limits are usually assumed to be sufficiently accurate for other analyses, except under special conditions such as meeting close specifications for coals showing wide variability in sulphur, fusibility of ash, or other quality. 4: In. modern coal sampling the increment is recognized as the basis for taking samples. For a given accuracy the number and weight of increments specified are increased with: (a) the expected ash, and (b) the top size designation of the lot to be sampled. 5. It is extremely important that every sampler recognize that: the specified number and weight of increments are minimums, and that. the precautions to be used in order to take them properly are also minimums; that in the reduction of the gross sample the sizes specified for the coal after each stage of the crushing are maximum; that the quantities specified to be taken after each crushing stage are minimum; that any short cuts or failures to meet the requirements specified will reduce the statistical accuracy of the results, although it is possible that one or two checks on a few results may seem to show otherwise.

Jan 1, 1943

By R. F. Mehl, G. V. Smith

The decomposition of austenite in steels, because of its immerse practical importance, has been subjected to extensive study in recent years from the point of view of the mechanism of the process.1"3 Although much information has been acquired, a number of questions, principally of theoretical interest, remain. One is that of the atomic-crystallographic mechanism by which each of the various reaction products forms. The isothermal reaction products of the eutectoid decomposition in plain carbon steels (to which this study is restricted) have conveniently been classified in three general groupings—pearlite, bainite, and martensite. Of these several products, pearlite and martensite have been studied extensively, but bainite has received only scant attention. -As a result, the mechanism of the formation of pearlite and that of martensite are now fairly well understood while a great deal of uncertainty exists regarding bainite. Pearlite Pearlite forms from austenite by the precipitation of alternate platelets of cementite and ferrite, which grow into the austenite matrix.2--5 The rate of reaction may be described in terms of a rate of nucleation and a rate of growth.2.3 Mehl and Smith6 have attempted to determine the lattice relationships existing between the ferrite in pearlite and the' parent austenite. Using a pole-figure method of analysis, it was found that a limited number of ferrite orientations resulted from the decomposition of a single grain of austenite; it was not possible, however, to decide between two assumed ideal relationships, both of which appeared to account for the experimentally determined pole figure. It was definitely shown, however, that the relationship obtaining was quite different from that determined for the proeutectoid separation of ferrite.7 No attempt was made to determine the habit plane (matrix plane to which the precipitate lies parallel) of the pearlite lamellae. Belaiew8 earlier had stated that the number of directions assumed by the pearlite lamellae in a single grain of austenite was 12 (no details were given) and concluded wrong!:!, as Mehl and Smith6 have pointed out, that the lamellae delineate the {2I0} planes of ferrite.* Martensite It is known that martensite is a transiti0nal constituent of body-centered tetragonal lattice,' and that it forms suddenly

Jan 1, 1942

By John P. Huger

me phase diagram for the system Ag-Si has been established by thermal analysis. The diagram is a simple eutectic type with a eutectic at 3.0 pct Si and 840°C. From the liquidus curve and with the aid of regular solution theory, the thermodynamic properties of the liquid Ag-Si system at 1420 °C have been determined. Silicon exhibits positive deviations from Raoultain behavior at all compositions, while silver exhibits both positive and negative deviations. MEASUREMENTS of silicon activities in liquid iron alloys by means of distribution studies between the immiscible liquids silver and iron have been reported by Chipman, Fulton, Gokcen, and caskey.' The applicability of this technique is dependent, however, on the accuracy of the silicon activity values in the Ag-Si alloys, particularly in the dilute silicon region. Darken and Gurry2 have shown that log ?si/(1-xSi)2 is approximately linear with composition, but uncertainty exists in the extrapolation to dilute solutions. Their calculations are based on the old Ag-Si phase diagram of Arrivaut3 and any variation in the position of the liquidus curves will strongly influence the extrapolation. The purpose of this study is to redetermine the Ag-Si phase diagram and calculate the associated thermodynamic properties. EXPERIMENTAL The Ag-Si phase diagram was determined by thermal analysis of liquid alloys. The alloys were contained in a 35 mm alumina crucible under a protective stream of purified argon. The crucible was placed inside a 64 mm alumina tube fitted with a gas-tight, water-cooled, copper head. The tube and assembly were heated in a manually controlled globar furnace. The temperature was measured with a Pt, Pt + 10 pct Rh thermocouple in a high-temperature porcelain protection tube. The thermocouple calibration4 was checked against the melting point of pure silver at the start and during the course of the experiments, and against both gold and silver at the completion of the experiments. The alloys were prepared from granular silver analyzing 99.95 pct Ag and powdered silicon analyzing 99.88 pct Si and 0.026 pct Fe. Approximately 150 g of alloy were used for each run. The composition of the alloy was determined by withdrawing samples of the liquid alloy with a vycor tube-aspirator bulb device. Analysis of solidified samples agreed, for alloys containing less than 23 pct Si, within ±0.3 pct Si of the calculated composition. Duplicate samples showed a variance within 50.05 pct Si of the mean analysis. The alloy was heated to 100' to 20pC above the estimated liquidus temperature and then the furnace was adjusted to give an average cooling rate of 2" to 7°C per min. A cooling curve was obtained by taking potentiometer readings at 15-sec intervals. Several analyses were made by recording the thermocouple output on a high-speed, Stip-chart recorder, with the exception of run NO. 11, a minimum of two thermal analyses were made for each alloy and the cooling curves then obtained duplicated the liquidus and eutectic temperatures to about 1°C. RESULTS The results of the thermal analysis are given in Table 1, and are represented as the Ag-Si phase dlagram, Fig. 1. The eutectic composition was found

Jan 1, 1963

By John R. Freeman

This paper relates entirely to the casting of brass under fluid pressure in steel dies. Die castings of metals and alloys of low melting point have been available for many years but the development of brass die castings has been relatively recent, occurring within the past five years. The successful developnlent of brass die castings has resulted from the availability of alloy steels that would give satisfactory life as dies and the development of suitablc die-casting machines. The melting point of copper is 1084" C. (1983" F.) and of a high brass about 900" C. (1652" F.), as compared to 327.5" C. (621.5" F.) for lead, 419.4' C. (786.7" F.) for zinc and 658.7" C. (1217.7" F.) for aluminum, temperatures that are indicative of the casting temperatures required for the various types of alloys, of which the melting points are somewhat lower than those of the pure metals. Type of Die-casting Machine In the well-known plunger and gooseneck types of die-casting machines used for casting the alloys of relatively lower melting point, much of the working mechanism is immersed in the molten alloy. For alloys having the relatively high melting point of brass, this obviously is impossible. Machines with a separate melting chamber are essential. Two rather distinct types are in extensive use at the present time, the Pack and Polak machines, the former designed by Charles Pack and developed at the American Brass Co., the latter developed by Joseph Polak, of Prague, Czeclioslovakia. The principles of operation of these machines have been described in articles by Pack1,2,3 and by Sieg.4

Jan 1, 1935

By Thomas L. Garwood, F. C. Menk

IT is generally, accepted that no method of coal cleaning except froth flotation is effective in cleaning dust. In the majority of coals mined in the United States the dust sizes contain a high percentage of impurities, hence the removal of the dust from the coarse sizes lowers the impurity content of these sizes. Dedusted coal is desired as a means of providing a better feed to cleaning plants because of increased efficiency in both dry and wet plants. In dry-cleaning plants, a dedusted feed makes for a pervious and uniform bed. With a dusty feed the fines tend to segr6gate in the feed stream and pass en masse over the air separators, causing a lack of uniform aeration and fluidity of the bed necessary to efficient cleaning. In wet-cleaning plants dedusting of the feed often decreases the sludge problem to the point of eliminating the necessity of wasting wash water. It may be advantageous to eliminate sludge-settling equipment in favor of dedusting equipment, to provide the advantages of a dedusted feed to the wet-washing process. Dedusting advantages may include: (1) the removal of fusain, especially advantageous in plants washing coal intended for metallurgical coke; (2) prevention of the gradual build-up of solids in the wash water, with a consequent variation in the washing ability of the system; (3) prevention of the loss of dust to the sludge ponds, providing instead a fuel for local consumption or special markets. DEDUSTING The practice of dedusting, sometimes called aspirating, has presented a problem in disposing of the dust and intermediate small sizes recovered in the process. It has been found that no difficulty is experienced in disposing of the intermediate sizes, since they are free of fine dust and burn freely on grates built for small coal. They handle well, flowing freely from bins and hoppers and into conveyors, and pulverize easily. They have a low angle of repose. In tests made on this size as a feed to coke ovens, the results have been excellent, in that the natural breakdown of .coal in handling and shooting in the mine gives this small-size coal good

Jan 1, 1943

By J. A. Woolf, E. S. Leaver

THE purpose of this paper is to describe, in a general way, gold-dredging operations in California, with particular reference to unusual features, including types of deposits and recent attempts to improve the recovery of the gold. Dredging Areas The gold-bearing formations that traversed the western slope of the Sierra Nevadas for a north and south distance of some 300 miles furnished the immediate source of the gold found in most of the placer deposits of California. Erosion through a long period carried the gold, together with various forms of partly disintegrated material, to lower elevations and formed placer deposits. Through the classifying action of water in motion, the coarser gold and heavier material of various kinds were - deposited relatively near the source; consequently, in the higher mountain country, old river channels were worked feverishly during the early California gold-rush days because of their high gold content. With the working out of these known high-grade channels, and from the knowledge thus obtained of prehistoric stream beds, drift mining was started and flourished until about 1890. Even today many drift mines are operating with the objective of opening other old Tertiary river channels that have been covered by volcanic flows. Adjacent to these areas, which contained relatively high gold values in the older river channels, smaller particles of gold, gravel, and debris were deposited along the sides of the former stream beds and on the adjoining flat areas, thus forming the large placer deposits, which were worked principally by hydraulic mining. Following the course of the ancient rivers and of the present drainage system to the lower edge of the foothill country, extensive areas of alluvial

Jan 1, 1937

By Frank L. Gaddy

Falls of roof account for over 50% of the fatalities that occur in coal mines in the US. Thus, roof control is one of the more important phases of underground mining. In reality, the control of roof influences the system of mining and is a major determinant of the width and spacing of working places, operations at the mining face, ventilation control, and surface subsidence. Frequently, the control of roof is the largest single cost item. Roof control is a never-ending task, not only at the working face and throughout sections where men are working, but along haulways and air- ways that must be maintained for the life of the mine. This is because roof, even the hest of roof, slowly deteriorates, so it must be frequently examined, with corrective support applied when needed. As coal is excavated, stresses are set up in the roof because the previous equilibrium is upset, resulting in pressures that cause fractures and slight movements that are frequently hard to detect. Unless the immediate roof, in the excavated area, is given support by artificial means, it might fall or there might be a succession of falls, varying from a thin scale to several feet, depending on the nature of the top. Exceptions to this are those rare mines, or sections of mines, with hard, strong, nonweathering roof that requires no support. GENERAL CLASSIFICATION OF ROOF There are two broad types of roof as far as support is concerned: the immediate roof above the coal and the main roof. Artificial support for mining purposes is only concerned with the immediate roof as nothing except large blocks of solid coal, or massive concrete, will support the main roof. The immediate roof is generally a few feet thick but call vary from inches to 6.1 m (20 ft) or more. There are examples of where there is no imrncdiate roof as the massive main roof lies directly on the coal

Jan 1, 1981

By Michael B. Jones, Wayne R. Bruce, Cyrus W. Field

For more than a decade the Pacific Northwest has been a frontier of successful porphyry copper-molybdenum exploration. This vast region (about 2100 miles long, 350-500 miles wide) occupies a geologically complex mobile tectonic belt. It parallels the Western Cordillera from northern California-Nevada to southern Alaska-Yukon Territory, and west from the northern Rocky Mountain-Tintina Trenches to the Pacific margin. Right lateral displacement has occurred along major transcurrent faults that are sub parallel to the region and the transform Fairweather-Queen Charlotte fault zone separates the North American continental plate from the Pacific oceanic plate. Porphyry-type deposits are widespread, but producing mines are restricted to south and central British Columbia. Size and grade are variable (25 to +300 mt; 0.18 to 0.65% Cu with 0.014 to 0.049% MoS2; 0.14 to 0.28% MoS,) and secondary enrichment is normally unimportant. Metallization is genetically and spatially related to late quartz-feldspar porphyries that are within, marginal, or satellitic to composite batholithic intrusions. Radiometric ages of the plutons range from Miocene to Triassic-Jurassic (18 to 217 m.y. [million year] ). Country rocks are typically eugeosynclinal metasedimentary and metavolcanic assemblages of Permian to Jurassic age. Several of the older (pre-Late Cretaceous) deposits formed in submarine island arc environments and they may be genetically related to occurrences of volcanogenic sulfides in the greenstone country rocks. Deposition of bornite-chalcopyrite-molybdenite ores is controlled by contacts, breccias, and fault-fracture zones. Associated hydrothermal gangue minerals include biotite, orthoclase, sericite, kaolinite, quartz, anhydrite, and tourmaline. Isotopic data suggest a deep source for ore, gangue, and plutonic host rocks. Significant exploration features include porphyries, dike swarms, breccias, potassic alteration, barren quartz cores, gossans, and fringing halos of pyrite and propylitic alteration.

Jan 1, 1975

By C. D. Demond

IN reverberatory smelting, fuel is the chief item of expense, as it commonly is in processes using large percentages of it. Hence the most suitable supply is eagerly sought; that is, the supply which, in the end, yields the greatest net profit. The better grades are not infrequently bought, even at an advanced price, because they are apt to be decidedly more economical. High price, of itself, however, is no merit, for freight is generally the largest part of the cost of fuel, and the nearby supply may yield as high efficiency as that from a greater distance. If a poorer grade is reasonably good, and if its cost is low enough to more than offset the decreased technical efficiency, it is of course the more suitable. Any smelting, operation depends for both efficiency and economy on raising the furnace atmosphere considerably above the "critical" temperature; that is, above the temperature at which smelting is completed. If this temperature is not exceeded, smelting stops, no matter how much coal is burned; and the real value of a fuel depends on the number of degrees that the temperature is continuously kept above this point. For example, if one fuel maintains 2,500° F. and another only 2,100° F., while the "critical" temperature is 2,000° F., the first is worth at least five times as much as the second, although the increase above atmospheric temperature is only one-fifth more in one case than in the other. This "margin of temperature" above the smelting point is much more significant than the total number of heat units developed from the fuel. The case is parallel to that of water flowing from a pipe. The reservoir may contain a billion gallons of water; but, even though the fluid has come to the nozzle, not a drop will run out, where it can be of practical use, unless the level in the reservoir is higher than the nozzle; and the speed and volume of flow depend on how much higher the level is in the reservoir than at this point. If the temperature inn a furnace is not above the critical level there will be no slag to flow over the skimming plate, even though there are enough heat units to bring an unlimited quantity of charge up to the point of slag formation; and just as the value of a water supply for the purpose of putting out a fire depends largely on the effective head, so the difficulties of furnace management

Jan 8, 1914

By N. Nemeth, L. L. Sirois

The role of the filter medium in continuous-vacuum filtration and the special circumstances which influence the resistance to flow through the porous cake and filter cloth are discussed. Due to negative pressure differential, gas bubbles evolve in the slurry, constrict passages in the filter cake and medium, and further restrict flow through the tortuous channels. Filtration is a liquid-solid separation process taking place at a porous medium under a pressure differential. The liquid passes through the medium; the solids are retained on the medium as a partially dewatered cake. Filtration is far from a simple process and has been described in terms ranging from "complex" to "subtle." Because of the many variables involved, no unified filtration theory has been developed, and the filtration process is still considered very much an art. In industrial filter design, basic relationships, whether derived for idealized conditions or developed empirically, are usually adapted to suit local conditions. In the mining industry where continuous-vacuum filtration is the main dewatering process, the physical state of the concentrates and the relatively low pressure differentials permit the assumption that the cakes are noncompressible, an assumption which leads to the use of theoretically sound rate equations. Notwithstanding this simplification, there are other problems, unique in the application of vacuum to dewatering, and until now completely ignored, which demand special attention. The basics of filtration involve the capture of solids on, while permitting the flow of liquid through, a porous layer of cake and cloth. Flow is determined by the structure of the solids which make up the cake and the particles permanently attached to the cloth. The problem of this structure, essentially one of solid geometry, has been considered insoluble by Hatscheckl as early as 1907 and by Freshwater as recently as 1967. Since cake structure is determined by the slurry parameters, that problem is far too large for inclusion in this study. For theoretical considerations, uniform buildup of the filter cake must be assumed; and for efficient practical operation, the resistance of the medium must be kept constant over long periods. The latter can be achieved by careful selection of the filter cloth, since the greatest part of the total filtration resistance will develop at the cake-cloth contact. This paper discusses the role of the filter medium in continuous vacuum filtration and the special circumstances which influence the resistance to flow through the porous cake and the filter cloth.

Jan 1, 1971

NEW MEMBERS The following list comprises the names of those persons who became members during the period Jan. 1, 1917 to Feb. 10, 1917. ALLEN, ROBERT SEXTON, Chief Chemist at Concentrator, Inspiration Cons. Copper Co. Globe, Ariz. ALTIO, KARL FREDRIK, Min. Engr., The Sissert Mining District Co., Ltd., Polefskoy Zavod, Perm Government, Russia. ARGALL, PHILIP HENRY, Mgr., Ozark Smelt. & Min. Co., Magdalena, New Mexico. BAILEY, MARC Supt., Wolverine & Arizona Min. Co., Bisbee, Ariz. BAKER, DAVID FRANKLIN, Asst. Supt. of Blast Furnaces, Alan Wood, Iron and Steel Co., Swedeland, Pa. BATES, BENNETT R, Min. Engr 1025 Peoples Gas Bldg., Chicago, Ill. BECK, HOWARD A Shift Foreman, Aurora Cons. Mines Co. Aurora, Nev. BELL, LEO RICHARD Casilla 270, La Paz, Bolivia, South America. BENJAMIN, FLOYD SHAW, District Mgr., Aetna Explosives Co., Inc., 800 Torrey Bldg., Duluth, Minn.

Jan 3, 1917

By F. N. Rhines

STUDIES upon the sintering of metal powders, in the solid state, have led to the proposal that the surface energy of the powder particles provides the driving force that causes points of contact between pairs of particles to grow into broad welds which isolate the residual vacant space into pores that tend to spheroidize and gradually to diminish in total volume.' Investigators differ with regard to the mechanism of the movement of the metal, under the influence of surface energy, to accomplish these changes. One school asserts that there is a mass movement of the metal, referred to as a "viscous flow," while the other school prefers to view the movement as a self diffusion process, wherein individual atoms are, transferred without disturbance of the basic pattern of the crystal lattice. Extensive experimental studies upon the sintering of copper, conducted recently by A. J. Shaler,2 have been in- terpreted by their author as support for the viscous flow mechanism of transport, the theory of which was developed originally by J. Frenkel.3 Duplicating a portion of this work with minor changes, G. C. Kuczynski4 is led to the alternate view, namely, that the initial stages of sintering, at least, proceed as a self-diffusion process. Both of these investigations were designed to deal with an isolated unit of sintering, i.e., with the shrinkage of a single pore, or with the growth of a single point weld. It remains to ascertain the behavior of a typical metal powder compact composed of a large number of particles of varying size and sintering to a body with a multiplicity of pores. The observation of density changes alone during sintering is not sufficient in such a case; it is essential to know how the internal geometry of the compact changes. This has been the object of the present investigation, the results of which are used to support the self-diffusion mechanism of sintering. The present studies consist in the measurement of the number of pores as a function of size and time at temperature during the sintering of a copper compact made from a commercial copper powder lightly pressed and sintered in several different atmospheres. A brief survey was made also of the change in shape of the pores, under the influence of the same variables. All of this was done by direct observation with the microscope. Densities were measured on the same sample. It is found that, while the compact is exhibiting an overall shrink-

Jan 1, 1951

By Robert Glass Cleland

THE THIRD and most important item on the Phelps Dodge agenda for the development of new ore supplies involved the site of the company's initial venture into Arizona, the old mining camp of Morenci. By the purchase of the Arizona Copper Company's holdings in 1921, Phelps Dodge had obtained control of virtually the entire Morenci district, including town, public utilities, and, above all, the huge mineralized area that had once been divided between numerous competing companies. Because of this rigid concentration of ownership in the hands of one organization, Phelps Dodge was able to plan and successfully carry out a program of greater magnitude than any Arizona mining company had previously under- taken. The immense deposit of low-grade ore, usually referred to as the Clay Orebody, had been known to the mining companies of Morenci for many years. Pioneer exploratory work, both by the Arizona Copper Company and later by Phelps Dodge, revealed that the deposit, mostly of light-gray porphyry rock, lay under a hard capping from two hundred to five hundred feet thick. An intensive drilling

Jan 1, 1952

By Kenneth C. Vincent, A. M. Gaudin

IN a study1of the action of amyl xanthate on chalcocite in water suspension, it was found that if the xanthate is added in relatively large quantity the xanthate group can be accounted for in three forms: (1) as xanthate ion remaining in water, (2) as benzene-soluble cuprous xanthate on the chalcocite, (3) as a benzene-insoluble coating on the chalcocite. Reduction in the amount of xanthate added leads to disappearance of form 1 then of form 2. With minute quantities of added xanthate, substantially all the reagent is of the "unleachable" kind. Yet this unleachable xanthate can be dissolved by pyridine to form a soluble cuprous xanthate complex, and it is sufficient in effectiveness to make chalcocite flotable even if insufficient in quantity to form a complete monomolecular film on the mineral. In that study it was also found that chalcocite abstracts cuprous xanthate from benzene solution, in what may (or may not) be a case of molecular adsorption. It seemed desirable, therefore, to study further the "unleachable" xanthate on the chalcocite, and particularly to ascertain whether it is formed as a result of the benzene leach or is actually formed during the conditioning of chalcocite in aqueous xanthate solution. A splendid tool to make such studies has recently been perfected; that is, the use of radioactive spies or tracer atoms. With this tool, it was thought possible to answer the problem stated above, but, unfortunately, this did not prove to be true. Answer to the flotation question was clouded by the existence of rapid and selective diffusion of copper atoms in the solid mineral-a phenomenon that was totally unexpected yet remains interesting and perhaps important. METHOD OF RADIOACTIVE SPIES The method of radioactive spies is discussed in many places. Two convenient references are the article by Evans2 and the book by Pollard and Davidson.3 The method was first developed by Von Hevesy and Paneth in 1913, when only natural radioactive isotopes were available. These isotopes are few in number, and so the method remained limited in scope. Recently the synthesis of over 350 active isotopes of all the known stable chemical elements4 has opened widely expanded possibilities for the method. A fundamental tenet of the method is that a radioactive atom and a nonradioactive atom are exactly alike until disintegration of the radioactive atom. Then, by its sudden death, the spy reveals its location. The relative abundance of spies at various locations makes it possible to ascertain the relative abundance of the corresponding nonradioactive atoms at the same times and locations. A second fundamental tenet of the method of radioactive tracers is that the radioactivity lies in the nucleus of the atom: transfer of radioactivity from one

Jan 1, 1944

By Charles H. Thurman

The data given herein were first included in a paper read before San Francisco Section, A.I.M.E., in October 1940, and are applicable to conditions existing until the gold-dredging industry was temporarily suspended by Order L-208 of the War Production Board in the fall of 1942. There is no doubt that gold dredging will be resumed at some future time, and on a scale equivalent to that of the recent past, but the cost data given herein will be affected to some extent by conditions existing at that time, and by labor rates and prices for materials then prevailing. Dragline vs. Bucket-line Dragline dredges should not be considered for mining large areas of low-grade placer gravel. In such deposits a dragline operator with a 5-cu. yd. dragline would be doing well to maintain an operating cost of 6¢ per cu. yd., while a bucket-line dredge with buckets no smaller than 7 cu. ft. each could be operated for less than 4¢ per cu. yd. By operating costs, I mean only field charges such as direct operating and overhead, which includes pay roll, power or fuel, repairs and maintenance, insurance, land clearing and general expenses, but not including such items as prospecting, depletion, depreciation of equipment, State Franchise Tax, or Federal Income Tax. It is not to be inferred that a dragline dredge cannot make a profit in small low-grade deposits, where the extent of a given property is too small to justify the use of the more costly bucket-line dredge. Consider small deposits of 106 gravel. It is obvious that a deposit of 5,000,000 cu. yd. of such gravel could not be mined profitably with a new 7-cu. ft, bucket-line dredge, costing upward of $250,000, and in operation costs at 4¢ per cu. yd., paying for land or royalties out of earnings; nor could a new combination 5-cu. yd. dragline and washing plant, worth upward of $125,000 and working at 6¢ Per cu. yd., make a profit. These comparisons are made because the hourly capacity of both types of dredges is nearly the same. The bucket-line dredge averages 93 per cent operating time in 24 hr., as against about 80 per cent or less for the dragline dredge. These Percentages of operating time are important factors in making a comparison of this kind- The bucket-line dredge has greater efficiency in cleaning soft bedrock, usually characteristic of dredging deposits, and a 7-cu. ft. bucket-line dredge can be efficient to a total digging depth of 80 ft- (65 ft. below water, 15 ft. above). A 5-cu. Yd. dragline dredge is limited to about 30 ft. of efficient digging depth, 5 ft. of which could be above water. In small areas of gravel not over 30 ft. deep, a 5-cu. yd. dragline dredge could make a profit where a bucket-line dredge could not do so. As an example: compare the dredging of 3,000,000 cu. yd. of 10 gravel 28 ft. deep with bucket line, costin 4¢ Per cu. yd., and with a 5-cu. yd. dragline dredge operating at 6¢ Per cu. yd. Because of small yardage, new equipment is not warranted, therefore we can assume that the dredges of both types are used equip-ment, fully depreciated. Dismantling, mov-

Jan 1, 1946

By H. [Eyring], B. J. Zwolinski

[ ] The authors are to be commended for their excellent work on the activities of components in the solid state. It is, however, felt that certain points require clarification with reference to diffusion in the solid state. It is a well established point that any rate process in a non-ideal system can be expressed by the general equation [ ] where ko is the specific rate in an ideal system, and ?A, ?B ... , the activity coefficients of the reactants and ?± and ?M,?N the activity coefficient of the activated complex and the intermediates, respectively. With reference to diffusion, the following simplified treatment in correcting for non-ideality is proposed. The same free energy change is involved in moving a particle from a solution of one activity to a solution of another activity,

Jan 1, 1947