Search Documents

By R. W. Brown, J. L. Loper

The process of sand erosion has been harnessed to perform a useful function—the directed perforating of oilfield tubular goods and formation rock. In this process the sand is carried by a liquid medium and the resrrlting slurry is forced through a nozzle at an extren~ely high velocity. Upon impingement against casing or formation, the fast-moving sand particles erode a perforalion in the casing followed by cavity formation in the medium behind the casing. The many factors influencing the rate and extent of this penetration are inherently difficult to establish experimentally. Equations describing submerged jet behavior have been applied to these conditions. The following paper develops the equations for predicting the performance of the perforating jet. INTRODUCTION The cutting power of high-velocity sand has been well known in the petroleum industry for many years. Sand carried by a high-velocity gas stream causes severe erosion. This effect has been the cause of numerous production problems in certain areas. It was logical to expect that this phenomenon would one day be adapted to useful industrial applications. Development of mobile, high-pressure, high-horsepower pumping equipment in the last decade has made this possible. The sand erosion process involves pumping a fluid containing abrasive solids through a set of nozzles at a high differential pressure (2,000 to 4,000 psi). The pressure conversion into kinetic energy imparts high velocity to the sand particles which, upon impact with the formation face or casing wall, erode the material in an organized pattern. This paper attempts to establish the effects of the various parameters and to predict the performance and limitations of the process. The following factors will be considered: nozzle differential pressure, perforation size, sand concentration, nozzle stand-off distance and backpressure. In general, this discussion is presented along theoretical lines and is substantiated by field results and data where reliable field data exists. POWER EQUATIONS The penetration rate of a high-velocity hydraulic jet is proportional to the power or energy of the jet at the point in quesion. The power of the submerged jet will decrease with distance (or penetration) into the cavity created by the jet. As the cavity is extended into the formation, the power of the jet diminishes to a value equal to the threshold cutting power of the particular formation which is defiined as the lowest power level at which the formation will be abraded by the jet. Obviously, when this point is reached, no further cutting of the formation can occur. It is assumed that this power level for a particular formation is a function of the hardness of that formation. The following equation can be written for the hydraulic process of formation abrasion.

By John. C. Reed

THIS paper presents briefly some of the principal results of 3 ½ months field work during the summer of 1938 in the Chichagof mining district, southeastern Alaska. The report is preliminary and presumably will be followed later by a more complete report to be published by the Geological Survey. The paper is concerned principally with the structural geology of a block of steeply dipping graywacke as revealed underground in the Hirst Chichagof and the Chichagoff mines, the two principal mines of the district. The two mines have produced about $16,000,000 worth of gold and silver. The attitude of the graywacke, which is locally cut by dikes and sills of aplite, is remarkably uniform and trends about N. 62° W. The average dip is about 67° SW. The graywacke is cut by large faults, the best known of which are the Hirst and the Chichagof, whose average trends are about N. 30° W. and average dips about 75° SW. The faults at some places split into the bedding of the graywacke and at others are deflected from their normal trends for considerable distances along the bedding. The relative movements along the faults was northwest and up at about 30° for the south-west or hanging-wall sides. The ore bodies are elongate quartz lenses in the faults. Most of the quartz is mineralized but locally large quartz masses are too low grade to be mined. The emplacement of the ore bodies appears to have been structurally controlled in large part by the intersections of the faults with the bedding surfaces. Places where the faults split or are deflected appear to have been particularly favorable places for ore deposition. There has been some post-quartz movements along the faults but it is thought that such movements have not been extensive enough to greatly modify the original positions and shapes of the ore bodies.

Jan 1, 1939

By J. Lyndon Rosenblad

This chapter describes the development of a rocklike model material for use in tests with a rock-blocks model to investigate the failure mechanism of a discontinuum. In order to provide reliable results, the model material must be characteristic of natural rock and obey the laws of similitude. Initially, the development of such a material does not appear to be a difficult problem. Only when one undertakes such a task does he realize how little is actually known, and that there is considerable work yet to be done. A material that simulates rock in all of its physical properties probably will never be developed. There is now and probably always will be room for improvement. Improvement is needed not only in the component materials but also in the technique of preparation. The material developed and subsequently described in this chapter simulates rock in general and a schistose gneiss rock in particular. The material possesses many rocklike physical properties not found in previously used model materials. One of the most significant improvements of this material is that there is an increase of Young's modulus with an increase in confining pressure as determined by triaxial compression tests. A change in the usual procedure of material preparation was used to develop this material and is also described. MODEL MATERIALS USED IN THE PAST Intact Materials Numerous materials have been used by investigators in models in the past to simulate a wide range of prototype materials. Some of the materials used include cork, plastic, concrete, plaster of Paris, portland

Jan 1, 1972

Jan 1, 1969

By M. E. Lombardi

THE Coalinga oil field is located on the west side of the San Joaquin Valley, California. The structure is in general a monocline, the edges of the oil horizon resting on the foot hills and dipping gently toward the east. One prominent anticline occurs plunging southeast. The earlier drilling was done in the foot hills comparatively near the outcrop and the wells were shallow. The sands were followed eastward and, in the case of the anticline, along the plunge, the wells becoming deeper and deeper until the depth of 4,000 ft. was reached and passed. There is nothing to show that the oil will not be found in quantity at still greater depth. In fact, some of the best producers have tapped the sand at close to 4,000 ft. The recovery of oil still farther to the east, and therefore at greater depth, seems to be mainly a question of drilling. In this territory the formations drilled through are chiefly sands and shales; they will not "stand up" in an open drilling hole; the casing has to be carried close to the bit, and it is always difficult to keep the casing free for any considerable distance. Ability to carry casing of comparatively large diameter without conductor pipes for distances of 2,000 or 3,000 ft. or over is desirable in such territory chiefly for two reasons. It makes it possible to enter the oil sand with a pipe of ample diameter; it eliminates one or more expensive strings of casing which act only as conductors for the water string, and furthermore, in territory where waters are encountered which corrode steel rapidly, it makes possible the construction of a rust- and alkali-resisting water string. It is always desirable to shut off top waters, which may lie within 100 ft. or less of the oil sand, with 10-in. pipe. Where the depth is so great that a practical weight of 10-in. pipe will not withstand the probable collapsing pressures, 8 ¼ in. at least is desirable. About the limit of rotary drilling to date in California seems to be the setting of the 10-in. string at 3,200 ft., although the rapid advance in rotary work during the past year seems to indicate that this depth may soon be increased. It is my purpose now, however, to treat only of cable-tool drilling.

Jan 2, 1915

By M. C. Leverett

The behavior of mixtures of immiscible liquids in porous solids is of rapidly increasing interest to those engaged in the production of petroleum. The operation of artificial water-floods and the control of natural ones immediately raise questions concerning the fundamental nature of such processes. Moreover, it is now recognized that often water occurs dispersed throughout the rock from which the oil issues into the well,' and thus tends to move toward the well simultaneously with the oil. The work reported here is a laboratory investigation of the simultaneous, steady-state flow of oil and water through the same column of uncon-solidated sand. It is thus directly related to the situation in which water occurs in oil-producing sands; it may have less direct implications for the displacement of oil from sands by water. However, it is to be clearly understood that the experiments to be described were performed primarily to obtain information of a more or less fundamental nature, and are not an attempt to reproduce, on laboratory scale, any part of an oil field. The dynamic behavior of a system in which oil and water are flowing simultaneously through sand is best described in terms of its "effective permeability" to either phase. For incompressible fluids flowing through a system of uniform cross section, the effective permeabilities to the two phases, in darcys, may be defined by the equations: Ko = PA6A [la] and Ku = Q [lb] In order to put the results obtained on a comparable basis for different sands, the effective permeabilities will be stated as fractions of the normal permeability of the sand; i.e., fractions of its permeability to a homogeneous fluid. Algebraically, these fractions are: KO' = Ko/K, and KWr = K,/X [2a] and [Zb]

Jan 1, 1939

NEW MEMBERS The following list comprises the names of those persons who became members during the month of February, 1914: Members ASANO, KOSAKU, Vice-Mgr..: Ashio Copper Mine, Shimozuke, Japan. BIRD, FRANK H., Constr. Engr E. 417 Sixteenth Ave., Spokane, Wash. COLES, HENRY 0., Chem Copper Queen. Cons. Min. Co., Bisbee, Ariz. COLLEY, HYLTON H., Met Copper Queen Cons. Min. Co., Douglas, Ariz. DALEY, MITCHELL J., Mill Supt Utah Apex Min. Co., Box 753, Bingham Canyon, Utah. FISHER, GEORGE EDWARD, Director, 3d Vice-Pres., Grasselli Chemical Co. 1551 East 115th St., Cleveland, Co. FRASER, EVERETT L., Mill Supt Tightner Mines Co., Alleghany, Cal. FRASER, WILLIAM L., Min. Engr North Star Mines, Grass Valley, Cal. FROLLI, ALBERT W. Min. Engr 216 North Main St., Salinas, Cal. GEARHART, FRANK B., Chief of Smelter Dept., N. J. Zinc Co., 405 Columbia Ave.. Palmerton, Pa.

Jan 3, 1914

By J. M. Adams

It is my purpose to give some of the results obtained by an experience of nearly seven years in working ores by the method frequently called the Washoe Process, and in several mills of which I have had charge, but principally in the Owyhee Mill, at Silver City, Idaho, which had twenty 650-pound stamps, and sixteen pans. I shall discuss here merely the mechanical details for working ores generally, subdividing the subject as follows : 1. Preparation of the ore for the stamps; 2. The crushing in the battery; 3. The settling of sand or pulp in vats or tanks; 4. The treatment in the pans; 5. The results obtained in settlers, agitators, and concentrators; 6. The straining of quicksilver, cleaning of amalgam, and retorting; 7. The saving of slimes and their subsequent treatment; 8. The loss of quicksilver. For descriptions of the various kinds of orebreakers, stamps, tanks, pans, settlers, etc., I must refer to the various works on these subjects, prominent among which are the reports of the United States Commissioner of Mining Statistics,and the volume on "Mining Industry," the third volume of the United States Geological Survey on the Line of the Fortieth Parallel through the gold and silver bearing regions of the great West, undertaken under the able guidance of Clarence King, assisted by Mr. James D. Hague and others. In this discussion it will be assumed that the general arrangement of the quartz mill is understood; and the question will be treated how to secure, from such a mill, the greatest economy in working, combined with the largest results. This place seems fittest for a single preliminary suggestion—namely, that there should be double "floors" throughout the mill, so that nothing can sift through and be lost.

By Eric Jette

IN order to control a chemical process by other than empirical, rule of thumb methods, two types of knowledge concerning the reactions involved must be available: (1) the thermodynamics of the reactions, and (2), by no means less important for efficient operation, the mechanisms and kinetics of the reactions. Information on the thermodynamic side enables the operator to decide upon initial and final conditions, whether heat must be .added or removed from the system, whether the reactions proceed farthest in the desired direction at high pressure or low, etc. Knowledge of the mechanisms involves the determination of the individual steps by which an initial set of reactants, under given conditions, proceed to give the desired final products and kinetic studies upon which the mechanisms are based give the speed at which each of these reactions or steps take place. Thus thermodynamic studies of a 'reaction enable the operator to control the direction and extent to which the reaction can proceed, while kinetic studies enable him to control rates and thus the time' efficiency of the operations. The thermodynamics set the limit to which the reacting system approaches; the kinetics tell how fast the system actually approaches this limit. The two types of information are complementary and not antagonistic even though in discussing the mechanism the introduction of thermodynamics is entirely needless and generally of no assistance, while in thermodynamic studies mechanism need not even be mentioned.

Jan 1, 1931

By Frank Foote, E. R. Jette

In recent years the constitution of the high-silver aluminum-silver alloys has been extensively investigated. Hansenl has reviewed the literature to 1935. More recently, Obinata and Hagiya,2 Hofmann and Volk,3 Taziri4 and Tishchenko5 have confirmed the general features of the phase diagram in the region around 25 atomic per cent aluminum. In this paper we present the results of high-precision measurements of lattice constants of the silver-rich alpha solid solution in the homogeneous range and the neighboring two-phase regions. These results are used to establish the nature of the solid solution, the identity of directly measured densities with those calculated from lattice constants and the homogeneity limits of the alpha solid solution with respect to three different neighboring phases. A study of the earlier investigations indicated that the last two subjects in particular required new and accurate data. Experimental Procedure Preparation of the Alloys.—The alloys were made from high-purity silver and aluminum. The silver was "Proof Silver," 99.999 per cent pure, supplied by the U. S. Metals Refining Co. The aluminum was 99.97 per cent pure (contained Si, 0.009 per cent; Fe, 0.0016 per cent; Cu, 0.004 per cent) and was supplied by the Aluminum Company of America. The lattice constants of these two materials have been reported by Jette and Foote.6 Weighed amounts of the two metals were placed in alundum crucibles and melted in vacuo in a high-frequency induction furnace. The melts were allowed to cool in the crucible, the ingots thus obtained weighed about 10 grams. These ingots were then filed clean, hamered, again cleaned and given a homogenizing anneal in vacuo of from 6 to 15 days at temperatures ranging from 500" to 695°C. The ingots were air-cooled from the annealing temperature. Lattice-constant Measurements.—Carefully prepared filings for X-ray analysis were sealed into evacuated quartz or Pyrex tubes and annealed for various periods of time at suitable temperatures. The furnaces used were vertical, rapid-quenching furnaces, the samples being quenched by crushing the sample tube under water by means of a heavy plunger. The general X-ray technique has been previously described6 The cameras were of the symmetrical, back-reflection, focussing type. Ka, radiation from a cobait-nickel alloy target was used. The wave-length values were taken from the second edition of Siegbaum's book.7 A correction for the index of refraction was applied and the lattice constants were calculated by the method of Cohen.8, 6 The lattice constants were calculated to a common temperature of 25°C., using the value of the linear expansion coefficient of pure silver as 18.9 X 10-6. Presumably the expansion coefficient for

Jan 1, 1941

By Charles F. Ramseyer

The manufacture of iron and steel is one of the largest of our industries; and in point of size of single plant and equipment certainly the biggest of all industries. By the general public it is generally considered a prime example both of the marvelous technical advances achieved by modern science and engineering in the design and operation of equipment and of the efficiency of big business in the coordination of men and materials. Actually the operation of its basic processes has not changed significantly in either theory or fundamental design of equipment in the past 75 years. Though many other process industries have been born and developed, and not seldom completely revolutionized, during this period, the primary processes of making iron and steel are still carried out along the lines laid down, and in the equipment originated so long ago, by Bessemer, Siemens and Martin, and subsequently expanded to practically the modern scale by Carnegie, Schwab and Captain Bill Jones in the eighteen eighties and nineties. The application of the principles underlying the continuous counter-current physical and chemical interaction of solids, liquids and gases, which have been so successfully used in the rapid evolution of our chemical process industries, has been very largely lacking in the steel industry. In the days of the last-named giants, especially Carnegie, the steel industry made great and rapid technical progress. Carnegie's ever driving idea (as later with Ford in the production of automobiles) was the finding of new and better ways of making cheaper steel. Carnegie himself was a steelman, and so long as he dominated the industry its technical progress was rapid; and he, like Ford, was vastly successful financially as well, since his costs were continually being driven lower than those of his competitors by his advances in steelmaking technique.

Jan 1, 1935

By Francis Rich

BEFORE the world-wide depression, the primary purpose of most blast-furnace operators was to produce a maximum tonnage of pig iron per day for each furnace in blast. Some attention was paid to the conservation of labor and raw materials, but the idea was well established that low-cost pig iron was attainable only when each furnace was pro-ducing a high tonnage. After the depression had set in, the picture changed considerably. Each blast-furnace operator was forced to run his plant in a manner that best fitted the economical set-up of his company. A great deal of thought was expended on the different methods of operation, always with the idea of making each product in a way that would best serve his company financially. Because of this abnormal condition, the blast-furnace man was compelled to indulge in various practices of which many had been believed to be next to impossible up to that time. The ultimate purpose of these innovations was either one or a combination of the following: 1. To produce only enough pig iron for immediate consumption at a minimum cost. 2. To produce gas for boiler or mill use to supplant some higher priced fuel. 3. To consume the coke produced at the coke plant, which was often viewed as a byproduct. 4. To protect the cash position of the company. These conditions were met by diverse methods, some of which were: 1. Slow or decreased wind. In some instances the blast blown was held as low as 25 per cent of the normal volume. 2. Intermittent operation, in which the furnaces were shut down or "fanned" at frequent intervals.

Jan 1, 1935

By G. E. Steudel

The study of the possibility of effecting a lower cost in the manufacture of pig iron reveals the importance of the ever present question of slag chemistry and volume. Factors that determine slag chemistry and volume are the impurities in the ore available, the ash-sulphur content of the coke, and a flux material necessary to promote removal of sulphur. Of these, the ores present by far the major source of impurities and what may prove to be the lowest practical slag volume with desired chemistry in one locality may be considered low or high in some other center of iron manufacture. The Chicago district is not only blessed with ores of high quality, but with excellent coke and flux materials as well. It is the intent of this paper to discuss slag problems at the South Works only, where burdens consist of Mesabi ores, Michigan stone, and coke ranging from 7 to 9 per cent ash and containing an average of 0.57 per cent sulphur. Early in the development of modern blast-furnace practice, the consideration of slags was secondary to the many adjustments of mechanical difficulties, such as furnace lines, stock distribution, stove design for obtaining higher blast temperatures, improved chemical segregation and size of raw materials. Furnace operators, after making these improvements, turned their attention to the study of other refinements in practice, of which slag chemistry appeared to be the most important. It is only within the last two decades that operators have become familiar with the various aspects of slag compositions. The industry, while rather slow in its recognition, is indebted to such investigators as Rankin,1 Wright,1 Feild,2 Royster,2 McCaffery,3 Kinney,4 Holbrook,5 and Joseph,5 whose researches concerning the elimination of sulphur within the blast furnace and the effect of slag composition upon melting point, viscosity, and desulphurizing power have established criteria for the selection of slags of the requisite quality. Large slag volumes result in higher coke consumption and cost of disposal. Any attempt to lower slag quantity must be accomplished

Jan 1, 1940

By E. S. Grumell

THE correct sampling of coal and coke is becoming important to an ever increasing number of producers and consumers. This, therefore, may be an opportune moment to examine where we stand with regard to existing and proposed methods. In this paper an attempt will be made to review, as briefly as possible, some of the considerable amount of painstaking research which has been done in the last 10 years, and which has unquestionably led to a much better understanding of the subject. In so doing we shall try, on the one hand, to make clear where substantial progress has been made, and on the other hand, to draw attention to points that require further investigation. The paper is divided into sections in order to emphasize the major divisions of the subject; further, in order to retain this emphasis, detailed consideration of some of the points has been relegated to appendixes. No attempt has been made to give a complete survey of the literature, as this has already been done by L. A. Bushell.2 The following abbrevia-tions will be used: A.E., average error; P.E., probable error; S.W.R., size-weight ratio; B.S.I., British Standards Institution.

Jan 1, 1939

By D. A. Dahlstrom

Application of the cyclone to separation of undesirable -200-mesh clay, silt, and high-ash fractions from coal slurries was found to possess many economic and process advantages. Up to 93.3 pct removal was attained at rates of 113 to 155 gpm per sq ft of cross-sectional area.

Jan 2, 1951

Research and Development, once considered a luxury item only for well-heeled companies, has in the last two decades come into its own as a vital contributor to the fortunes of electronic, automotive, chemical and aerospace firms. In terms of money and talent poured into research, the mining industry is still far behind those industries. Although the U.S. Bureau of Mines, plus various mining and manufacturing firms and universities have made notable contributions to mining technology, the historical pattern of mining R&D shows a heavy reliance on the results of research in other industries. It is difficult to tell whether this pattern will change significantly in the future, but there is evidence of a growing awareness by mining officials that greater R&D efforts are going to be required not only to meet the nebulous demands of tomorrow's world but to meet the ever-present, mounting pressures being generated by "intra-metals" and "inter-materials" competition.

Jan 1, 1968

By B. Woyski

Many writers, in discussing defects caused by oxidation and gassing of bronzes and red brasses advocate substantially the same cure for both. But from its nature, oxidation cannot take place if there is an excess of fuel in the furnace, while the gases absorbed by some alloys are products of incomplete combustion of the fuel. Hence the metal can be either oxidized or gassed, but it is doubtful whether these actions can take place simultaneously. Oxidation can be easily overcome by the use of deosidizers or it may be avoided by protecting the molten metal with suitable fluxes. Absorption of gascs is more difficult to overcome: the regulation of the air and fuel, so as to produce complete combustion, and the protection of the bath by mineral fluxes arc the most important factors. Gas expulsion, resulting in gas holes, porosity, unsoundness, and swollen or cauliflower-headed risers, is said to have several causes. One writer1 lists the most common causes in the order of their importance, as follows: Superheated metal, dirty or slaggy furnace conditions, using metals low in quality or those previously subjected to bad melting practice, poor grade of fuel, use of newly lined or damp ladles, indiscriminate mixing of scrap or illogical combinations of metal. Superheating the metal usually occurs when the heat is ready to be poured but for some reason must be held in the furnace. In this case, a careful furnace tender tries to avoid overheating the metal by keeping a mild fire; that is, a reducing fire which, unfortunately, results in gassing the metal. A dirty, slaggy furnace may result in gassing the metal by retarding the heating and prolonging the time necessary to bring the metal to the proper temperature, thereby increasing the chances of gassing in uncertain furnace atmosphere. It is doubtful whether rnetals of low quality have anything to do with gassing molten metal, except, possibly in the case of metals containing

Jan 1, 1923

The following list comprises the names of those persons who became members during the period May 10, 1919, to June 10, 1919. ALAYZA, CARLOS Box 850, Lima, Peru, S. A. BALLARD, P. A Surveyor, Midwest Refin. Co., Custer, So. Dakota. BARNEBL, A. J., JR.... Mech. Eng., The Dorr Co., 101 Park Ave., New York, N. Y. BILLINGS, GOODSELL Platteville, Wis. BRONSON, C. B., Mech. & Met. Engr., New York Central Lines, Room 1520, Grand Central Terminal, New York, N. Y. BUNCE, E. H Met., The New. Jersey Zinc Co., Palmerton, Pa. CHARLTON, D. E. A., Editorial Staff, Engrg. & Mm. Journals 10th Ave. & 36th St., New York, N. Y. DAVIS, JOHN N., Supt. of Mills, Engels Copper Min. Co., Engelmine, Plumas Co., Cal. DUKES, GLENN H., Chief Engr., The Sunday Creek Coal Co.,1001 Outlook Bldg., Columbus, Ohio. ERICKSON, ARTHUR .... Engr., United Smelt., Refin. & Min. Co., Mldvale, Utah. FLYNN, A. E Supt., Rand Consolidated Mines, Ltd., Goudreau, Ont., Canada. HIBBARD, WALTER R 63 Ashley St., Bridgeport, Conn. HOBSBAWN, I. BERKWOOD, Cons. Tech. Chem., Messrs. Gibbs. & Co., Valparaiso, Chile, S. A.

Jan 7, 1919

By F. W. Lake

The ultimate production from a natural reservoir of petroleum is inversely proportional to the gas-oil ratios existing during the producing life of the reservoir whenever gas is the major expulsive force in the recovery. In other words, in the period during which gas is the major expulsive force the ultimate production will be increased if the gas-oil ratio is decreased, and vice versa. This condition prevails in the greater number of the present producing districts. While this relation is difficult to prove from actual operation, on account of the present paucity of detailed observations, it must be admitted after a study of the forces and conditions governing the recovery of petroleum from natural reservoirs. Where gas and oil exist under pressure in sand interstices and water movement is not freely possible, the force expended in moving the oil to the well is the expansion and movement of the gas through the pressure differential existing between the interior of the reservoir and the well. If pressure and solution conditions in the untapped reservoir are such that the relation between gas and oil volumes at atmospheric conditions is as 100:1; and if during the producing period, until the gas is exhausted, the relation between the gas and oil volumes produced is 300:1, it follows that only one-third of the oil has been produced and the remaining two-thirds cannot be recovered unless some extraneous force is introduced into the reservoir. This serves to illustrate the importance of gas-oil ratio control during normal producing operations. Gas-oil Ratio Control Eliminating natural conditions in a reservoir, which govern gas-oil ratios, such as the physical properties of the oil and gas, the physical characteristics of the reservoir strata and the original pressure and solution conditions in the reservoir, which cannot be controlled by operation practice; and also eliminating operating conditions that apply to the reservoir as a whole, such as well spacing, well locations, relative completion dates, various penetrations and drilling practice; there remains but one condition in each well that influences the gas-oil ratio and that is

Jan 1, 1928

Jan 1, 1904