Search Documents

By Robert R. Abbott

The practice of carbonizing steel for the purpose of case-hardening has assumed great commercial importance within the past 10 years. Formerly, case-hardened steel was held in more or less contempt, since it was considered a cheap substitute for tool-steel. This is no longer the case. The development of the motor-car industry, and coincidentally that of modern alloy-steels, has resulted in overcoming many difficulties formerly experienced in case-hardening. This result has been accomplished by increased knowledge regarding the analysis of the steel which would respond most readily to case-hardening, and by more careful methods of treatment of the carbonized steel. The ordinary method of carbonizing consists in packing the steel with the carbonizing-material in cast-iron boxes and placing them in a furnace at a temperature of from 1,500° to 1,900° F. for a time sufficient to give the required depth of " case." The steel is then either quenched directly from the box, or is allowed to cool without unpacking, and finally given a single hardening-heat, or, for special work, two or three heats. During the year 1911, more than 100,000 tons of carbonizing-material was sold in the United States, at an average price of probably $55 per ton. More than 85 per cent. of this material consisted of granulated bone. Within the past four years, many manufactured compounds have been placed on the market, consisting largely of some form of carbon or carbonaceous material, with or without the addition of chemicals. Steel will absorb carbon placed in contact with it at the temperature of the atmosphere. The reaction is exceedingly slow, but increases rapidly with increasing temperature. Below

Jan 1, 1913

By Gary Beerkircher

The mine hoisting equipment that is selected and installed at a mine is the lifeline of the mine, and therefore the proper selection of equipment will save a lot of time and money during the life of the mine. Various types of mine hoist designs &e available today, and each has their advantages and disadvantages. Double Drum Hoists, Single Drum Hoists, Friction Hoists and various special designs of these are available but should only be used on applications where they are suitable. There have been several new drive systems for mine hoists which have come into the picture in the last ten years, and they in turn must be evaluated along with the existing drive systems for each hoist application. It does not make sense to properly select the hoist mechanicals, and then have a drive system that turns out to be a bottleneck. This paper will attempt to cover the above noted systems - both the hoist selection and hoist drive system that will provide the mine with a reliable and economical hoisting system. I. Mine Hoist Types There are two basic types of mine hoists available in the world today: the drum hoist on which the hoist rope is actually stored during the hoisting cycle, and the friction (Koepe), which merely passes the rope over the wheel during the hoisting process. Following is a general outline of each type of hoist and the hoisting applications that they are suitable for. First let us consider the simple Single Drum Hoist. As a Service or Production Hoist with cage or skip in balance with a counterweight, a Single Drum Hoist can efficiently service one or more levels since the location of the counterweight at anytime is not important. As a Production Hoist with skips in balance the Single Drum Hoist is best used for single level hoisting. All rope adjustments for proper spotting must be done manually for the Single Drum Hoist. This has to be done periodically to compensate for rope stretch. A variation of the Single Drum Hoist is the divided drum hoist. If multi-layer winding is necessary the Single Drum Hoist must have a divider to allow a separate compartment for each rope. If a counterweight is used with a divided drum application the counterweight rope can be wound on a smaller diameter (Figure 2). Consequently, it moves a lesser distance than the main conveyance and rope adjustment problems are reduced.

Jan 1, 1975

By S. Mukai, Y. Shah, T. Zshikawa, T. Wakamtsu

In order to recover coal concentrate of low ash and low iron content, the electrostatic separation of coal was studied. It is more successful in the corona discharge field to recover the coal concentrate of low ash and low iron content than in the field without corona discharge. The effect of humidity on the electrostatic separation of coal was then studied. From the experimental results, it was clear that the electrostatic separation was excellent in about 60% relative humidity of atmosphere. Thus, the separation of vitrite from coal is practicable by electrostatic separation. In recent years the demand for high quality coal containing low ash, low iron, and low sulfur has increased. To fulfill this requirement, a higher grade coal concentrate must be produced. Study on the electrostatic separation of coal has been performed for several years in the author's laboratory. From the results of this research, it was considered that the behavior of coal particles in the electrostatic field relates closely to the ash and iron content in coal. In the present paper, the electrostatic separation of coal in corona discharge field was studied in order to recover the high quality coal concentrate and then the effect of humidity on the electrostatic separation was investigated. PREPARATION OF COAL SAMPLES The coals from the Akabira mine, the Kushiro mine, the Miike mine, and the Oshima mine which are famous coal mines in Japan were used in this study. The ash contents of these coals are shown in Table I. From the results of the analysis of the coal samples by the Norelco X-ray diffractometer, it is recognized that the Miike coal includes mainly pyrite, quartz, kaoline, calcite, and epidote; the Kushiro coal: kaoline, quartz, and montmorillonite, and the Oshima coal: siderite, dolomite, and other substances. For the preparation of samples, the coarse pieces of coal were crushed to about 2 mm in diam and then ground in an agator mortar. The ground products were sieved and fractions of 10 — 14 mesh, 14 — 20 mesh, 20-28 mesh, and 28-35 mesh were prepared, respectively. APPARATUS OF ELECTROSTATIC SEPARATION The principal part of the apparatus of the electrostatic separation used in the experiments is shown in Fig. 1. In order to generate the corona discharge field, a needle-shaped electrode combined with a pole electrode is installed as the high tension electrode. In the case of investigating the effects of the humidity on the electrostatic separation of coal, the needle-shaped electrode was combined with a plate electrode instead of the pole electrode as shown in Fig. 2. The pole or the plate electrode was installed to promote the repelling of the charged particles by producing the electrostatic field between this electrode and the grounded roller. It seems to be very useful on the coal separation to install these combined high tension electrodes. SEPARATION OF COAL PARTICLES IN CORONA DISCHARGE FIELD The separation testings on the coal samples in the corona discharge field were performed by the apparatus as shown in Fig. 1. These experiments were carried out under the following conditions: feed size 20 — 28 mesh, room temperature, normal humidity and applied voltage 15-20 KV, and the combined electrodes including the needle-shaped electrode were negatively charged. The results of these testings are

Jan 1, 1968

By S. J. Aresco, George E. Keller, J. Visman

INTRODUCTION The accurate sampling of coal, as with most minerals, is a difficult task. Coal is a very heterogeneous material made up of different types of coal and varying amounts of mineral matter. The product as mined may contain all of the layers of coal and impurities found in the seam as well as portions of the strata above and below the coal seam. The preparation plant is the device to size, crush and/or remove impurities so that the coal may be shipped as a saleable product. Sampling may be needed at many stages in the preparation process. Although this chapter is mainly concerned with sampling in connection with preparation processes, the principles will apply to all coal sampling. The main reasons for sampling in connection with coal preparation are: 1. To determine the washability characteristics of the raw coal by means of float and sink tests. These may be used for the design of a preparation plant, prediction of results to be obtained or for monitoring raw coal delivered to the plant. 2. To check the performance of various operating units in the plant, either by float and sink tests or chemical analyses. 3. To determine the analytical characteristics of the products produced, such as moisture, ash, Btu, sulfur, etc. HISTORY The earliest accepted methods of sampling coal in the United States were given in U. S. Bureau of Mines publications by J. A. Holmes,1 G. S. Pope2 and A. C. Fieldner.3 The American Society for Testing and Materials more or less adopted the methods proposed by the U.S. Bureau of Mines in their Standard D-21-1916, and it remained a standard for many years. Briefly, the standard called for a 500 pound sample for coals less than. 3/4 -in. in size and a 1,000 pound sample for all coals over ?4 -in. in size. No mention was made of increments but there was an instruction that the sample should spread over the coal to be sampled. Sample preparation was by hand crushing with the alternate shovel method for reduction to 250 pounds followed by coning and quartering below 250 pounds. Obviously, with the amount of work involved, this method of sample preparation was rarely followed. This method of preparation resulted in samples that were practically air dried because of long exposure while crushing, shoveling and quartering. In the late nineteen twenties and early nineteen thirties, studies for more practical methods were begun. Dr. E. S. Grummell4, Imperial Chemical Industries, Ltd, London, summarized the work to date at the

Jan 1, 1968

By J. C. McCarthy, J. B. Stone

AT Fresnillo a series of veins that has yielded very large quantities of silver and other metals has been developed over a length of 6500 ft. and to a depth of over 3000 ft. In the course of this work striking changes in the mineralogy and metal content of the principal veins have been disclosed and are well illustrated by assay data and ore reserve calculations. This paper describes those changes and suggests their bearing on theories of ore deposition. LOCATION The Fresnillo mines and the adjacent city of Fresnillo are in the central part of the state of Zacatecas, 35 miles northwest of the capitol city of Zacatecas, once a great silver-mining center whose total production is said to place it fourth in the world. Another famous old silver district, Sombrerete, lies northwest of Fresnillo. Fresnillo is connected by a 5-mile branch with Fresnillo station on the Mexican National Railways line from Juarez to Mexico City. Lying near the southwestern edge of the central plateau of Mexico, Fresnillo ís surrounded by a semi-arid rolling plain from which rise widely scattered low hills. One of these is Proaño hill, an inconspicuous elevation rising barely 300 ft. above the plain, but in and around Proano hill are the Fresnillo mines, and it is marked now by a great gash cut by glory-hole mining. HISTORY According to an account written in 1834 by Francisco García, then Governor of the state of Zacatecas, Fresnillo was discovered in 1554, and a presidio was established there in 1568 to protect travelers on the road between Zacatecas and Sombrerete. Little is known of the earliest mining at Fresnillo, which seemingly began soon after its discovery, but by piecing together various accounts, it appears that mines there were working in 1717 and were notably active ín 1751 under an administrator named Murguía, who left detailed notes describing them. In 1757, however, the mines became inactive because of difficulties with creditors and no doubt also because of increasing water troubles, and they remained abandoned until 1830. In 1830 the mines at Fresníllo became the property of the State of Zacatecas because the interest of Governor García had been aroused by the long disregarded notes of Murguía. Under García's energetic leadership the mines were reopened, and silver production began in 1832 ín spite of serious difficulties, including abnormal rains and an epidemic of cholera. In 1835 English capital was sought to allow installation of steam-driven Cornish pumps at the two principal shafts and to build the great hacienda de beneficio (the present Proaño hacienda). The company formed in 11835 (Cia. Zacatecano Mexicana) operated successfully until 1872, when its career was brought to an end by the political and economic disturbances

Jan 1, 1942

By Valentin R. Garfias

PRODUCTION AND MARINE TRANSPORTATION OF MEXICAN PETROLEUMS ALTHOUGH the work on which this paper is based was carried on, by the writer as Special Commissioner of the Petroleum Department of the Mexican Government, the opinions expressed are only his personal views for which the Mexican Government can in no way be held responsible. Notwithstanding that the appointment covers all phases of the so-called petroleum question, as the one question of immediate importance was that relating to taxation, it was decided to devote all the time to this phase of the work. The present report has been divided into two closely related parts, .the first dealing with the production and marine transportation of Mexican petroleum, and the second, with the Mexican taxation on petroleum and its products. The writer wishes, to acknowledge the loyal cooperation rendered by Mr. M. C. Ehlen, who had charge of the statistical, work, and by Miss S. Stern and Messrs. E. P. Heiles and J. E. Morrissey. The aim throughout the work has been; to pave the way for a thorough understanding between the Mexican Government and the oil operators and to present a true and clear statement of facts relating to the questions at issue.

Jan 2, 1921

By William P. Blake

IntroductioN.............989 The Blake stone- Breaker Prize.......989 Great Labor-Saving Inventions.. 990 I. Biographical NoticE OF the Inventor......990 II. Former Methods of Breaking Stone......992 Ragging and Spalling......... 992 Cornish Rolls..........993 III. Construction of the Blake Stone-Breaker.. .. 993 The Lever.Pattern.........994 The Eccentric Pattern.........997 The Challenge Pattern......... 999 The Monarch Pattern.........1001 The Multiple-Jaw Pattern........1001 Movable Dies for Jaws......... 1004 Cheek.Plates,..........1007 IV. The Capacity OF Blake Breakers......1007 Position and Feeding of Breakers...... 1008 V. Gyratory Jaw Crushers.........1010 The Gates Rock- and Ore-Crusher......1010 The Comet Crusher.........1010 VI. Some Unusual Forms OF the Breaker......1010 The Smith Hydraulic Pattern.......1012 The Forster Crusher.........1012 The Stafford Crusher.........1013 The Gates Crusher.........1013 The Dodge Pattern.........1013 The Rawson Crusher.........1014 The Duplex Breaker.........1015 Booth's Modification of Wedge-Block......1015 Marsden's Eccentric Pattern.......1017 The Lancaster Machine........ 1017 VII. Combined Crushing and Grinding Impracticable,. . 1018 The Hanscomb Machine ...1019 Howland's Crusher and Pulverizer..1020 The Oliver Crusher and Pulverizer..1021

Jan 1, 1903

By Richard H. Jahns

Such minerals as beryl, lepidolite, sheet muscovite, spodumene, and tantalite-columbite are obtained chiefly from pegmatite bodies that are internally zoned. As shown by examples of such pegmatites from the Southwestern and Southeastern States during World War II, studies of their internal and external structure have value in prospecting and the planning of exploration, development, and mining.

Jan 1, 1951

Secretary Membership Committee Increase of Membership Papers and Publications Committee Library Committee Treasurer Report of the Secretary TO THE BOARDOF DIRECTORASN D THE MEMBEROS F THE AMERICANIN STITUTE OF MINING AND METALLURGICAENL GINEERS GENTLEME:N As will be shown by the special reports of the Finance, Membership, Library, Papers and Publications, Increase of Membership, and other standing Committees, together with that of the Treasurer, the year 1927 was one in which the Institute made very satisfactory progress in a number of directions. In total numbers the membership is no larger but in revenue from dues there has been a marked increase. This has been due to the promotion to full membership of Junior Associates of earlier years, to the larger proportion that come in originally as members rather than juniors, and to the keener interest in the work of the Institute reflected in prompter payment of dues. The latter is important, since experience shows that of those who fall behind a large number must ultimately be dropped for non-payment. Conditions in the mining industries have been healthy though not booming. It has been much easier for members to find employment and meet their financial obligations but there has not been that flow of young men into mining, and hence in part into the Institute, that characterized certain earlier years. Rather the tendency toward centralization and larger industrial units has restricted the number, though not the scope, of opportunities for technical men in the mineral industries. The Institute is constantly receiving resignations from members crowded out of mining into other lines of activity. On the other hand, those who remain in mining and metallurgy have a greatly increased necessity for i,dormation and contacts with technology. A few years ago many superintendents and most foremen were non-technical men. Today the reverse rule obtains and shift bosses and men who occupy even lower positions in industrial units are called upon to know and to apply such an amount of technical knowledge that graduate engineers are the rule rather than the exception. The curious situation has obtained that with a much smaller enrolment of students in the schools of mining and metallurgy there has been at times an actual shortage of young engineers for beginners' jobs. The young men retort that the conditions of employment and pay offered in mining are not equal to those in other lines and, while it is undoubtedly true that the young engineer beginning in mining is able to start under conditions markedly better as to pay, living, and responsibility than did the men who are now leaders, they are required to know much more and have usually spent more in time and money to qualify for their jobs. The whole matter is one which warrants much more attention than has been given to it. For the Institute it is important since the young men

Jan 1, 1928

By W. A. Ver Wiebe

It is becoming increasingly apparent that the State of Kansas contains one of the largest reserve areas for oil exploration in the United States. During the year 1936 no less than 54 new oil pools were discovered by drilling. In addition, seven gas pools were found, which may develop into oil pools when deeper horizons are tested. Several old pools increased their reserves when production was found in lower strata. The data presented in Table 2 indicate that nearly 2000 wells were drilled in the state during 1936. Of these more than 1214 found commercial quantities of oil and at least 61 found marketable quantities of gas. The data are conservative because complete results on drilling are not available for the eastern part of the state. Ellis, Rice and Russell Counties share honors with a total of 10 new pools in each. Barton County is prominent with six pools; while those counties claiming fewer new pools are Clark, Ellsworth, Harvey, McPherson, Ness, Pawnee, Rooks, Stafford and Trego. Important additions to our gas reserves were found in Finney and Haskell Counties, which are north of the extensive Hugoton gas area and may some day be part of it. At the close of the year there were 17,317 wells in the state rating as producers. By far the larger share (14,000) were classed as strippers and allowed to flow 100 per cent of their potential capacity, thus accounting for 33,500 bbl. a day. The remaining wells, capable of producing from 15 up to over 6000 bbl. per day, were limited in output according to these amounts. The largest wells having a potential of from 3000 to 7000 were allowed to flow from 2 to 3½ per cent of their official potential capacity. The percentage rises until wells of 15 to 20-bbl. capacity have a rating of slightly over 83. On the basis of these calculations the total potential capacity of all wells was 1,667,814 bbl., and the daily amount allowed was 175,851. Nine of the pools most recently opened were still unable to market their oil and were classified as "shut-in" pools. Total production for the state for 1936 was somewhat over 58 million barrels. Striking Geological Data Some interesting geological data were uncovered by deep drilling during the year. The most remarkable bit of information is the discovery

Jan 1, 1937

By O. W. Simmons, L. W. Eastwood, C. M. Craighead

Eighty-four quaternary titanium-base alloys from the following systems were investigated: 1. Titanium-chromium-carbon-nitrogen. 2. Titanium-chromium-carbon with copper, vanadium, molybdenum, manganese, iron, or nickel. 3. Titanium-chromium-nitrogen with vanadium, molybdenum, or nickel. The tensile properties, minimum bend radii, hardnesses, response to heat treatment and aging treatment, and phase relationships of these alloys are reported. HIS paper is the third in a series describing J- titanium-base alloys. The first paper describingdescribed titanium binary alloys, and the second contained data on a large number of titanium ternary alloys. Eighty-four heats, comprising three groups of quaternary titanium-base alloys, are described in this paper as follows: 1. Titanium-chromium-carbon-nitrogen alloys. 2. Titanium-chromium-carbon alloys containing copper, vanadium, molybdenum, manganese, iron, or nickel. 3. Titanium-chromium-nitrogen alloys containing vanadium, molybdenum, or nickel. The methods of preparing, fabricating, and testing the alloys are described in the paper Binary Titanium Alloys. Quaternary Titanium - Chromiurn - Carbon -Nitrogen Alloys The properties of titanium-chromium-nitrogen and titanium-chromium-carbon ternary alloys have been described in the paper Ternary Alloys of Titanium. Because small amounts of nitrogen and carbon both appear to be somewhat beneficial, these additions have been investigated fairly completely in quaternary alloys containing chromium at the following levels of composition: 2.5, 3.5, and 5.0 pct chromium 0.25 and 0.5 pct carbon 0.1 and 0.2 pct nitrogen Mechanical Properties: The mechanical properties of these alloys are listed in table I. Fig. 1 and 2 show graphically a comparison of the tensile properties and hardnesses of quaternary alloys with those of the titanium-chromium binary alloys. Fig. 1 shows the comparison at 0.25 pct carbon, whereas fig. 2 shows the comparison at 0.5 pct carbon. It is concluded from these data that 0.25 pct carbon and 0.1 pct nitrogen are desirable additions to the 5 pct chromium-titanium base. It is further concluded that most of this improvement is produced by the nitrogen and that carbon is either harmless or mildly beneficial, at least up to 0.25 pct. Structure and Transformation Range: The effects of carbon and nitrogen on the transformation range of the titanium-chromium alloys were determined as part of the routine investigation. Additions of 0.25 pct carbon and 0.1 pct nitrogen had no appreciable effect upon the transformation range. However, the addition of 0.25 pct carbon and 0.2 pct nitrogen definitely raised the beta solvus temperature, as shown by fig. 3.

Jan 1, 1951

By R. W. Gurry

In the course of a series of measurements of the rate of diffusion of carbon in austenite at about 960°C. (1760°F.) and III0°C. (2030°F.), it became necessary to determine carbon concentration when austenite is saturated with graphite, because of indications that the hitherto accepted value of the solubility of graphite in this temperature range is too low. Specimens of carbonyl iron were saturated at temperature in a hydrogen-toluene atmosphere which was in equilibrium with graphite. The carbon conteDt of the steel was measured either by combustion or by the loss of weight after substantially complete decarburization in an atmosphere of hydrogen saturated at room temperature with water vapor. The absence of carbide or graphite as a phase at temperature was demonstrated by microscopic examination of saturated specimens that had been drastically quenched, The mean result of concordant ments-—taeats-is-^that gamma iron saturated with respect to graphite contains 1.39 per cent carbon at 957°C .(i755°F.) and 1.89 per cent at III0°C. (2030°F.). These two values, plotted along with what appears from the literature to be the best value (0.69 per cent) at the iron-graphite eutec-toid temperature (738°C. or I360°F.), yield a curve that is almost linear, and which, continued upward through a short interval, leads to a limiting solubility of 1.98 per cent at the iron-graphite eutectic temperature II35°C. (2075°F.) instead of the commonly accepted value of about 1.7 per cent. Experimental Procedure The samples of carbonyl iron, with the exception of those for microscopic examination, were cylinders 3.8 cm. long, 0.475 cm. in diameter. They were placed in a graphite holder and suspended in a vertical furnace, the temperature of which was controlled precisely by means of the resistance of the platinum winding.' In the empty furnace the range of temperature over a distance of 4 cm. at the heat center was 9°C. (I6°F.) but at a given location the temperature remained within +o.5°C. (o.9°F.); it was measured by inserting a platinum-rhodium couple calibrated at the melting point of palladium, 1555°C. Since the presence of the sample probably improved the uniformity of temperature, it was decided to consider the average temperature of the sample to be 3°C. lower than the maximum measured in the empty furnace with the same setting of the controller. Data were obtained in the vicinity of two temperatures, 960°C. (I760°F.) and III0°C. (2030°F.). The samples for microscopic examination, 2.2 cm. long, 0.475 cm. in diameter, were suspended individually on pure iron wire; for these no temperature correction was applied. The carburizing gas passed into the furnace was dry, oxygen-free hydrogen saturated at room temperature with toluene; this quickly produced on the

Jan 1, 1942

By J. J. Jakosky

A REVIEW of the progress in applied geophysics during the recent depression years reveals marked advances "over the methods employed several years ago. Of late, geophysical work has been curtailed to a con-siderable extent in the fields of oil and base-metal exploration, its especial domains a few years ago. Greater attention has been directed toward the use of geophysical technique in other engineering problems. Constantly maintained research programs have developed new instruments and per-fected better field, laboratory and interpretation techniques based on experience and skill acquired from years of application in the older geophysical field. During the past two years, geophysical methods have been employed in problems that required information on thickness of fill materials and subsurface bedrock contours. Considerable success has been attained, with subsequent drilling checking the predicted depths within one to five per cent. In general, these problems were similar as far as the fundamen-tal physical and geological conditions were concerned, but they have varied widely in specific detail and in engineering aspects. Character-istic of the different problems are: (1) yardage and bedrock profile in gold-placer mining; (2) water supply, involving underground drainage and storage conditions; (3) bedrock contours in dam-site and other structural investigations; (4) gravel and fill yardage, and other structural features along rights of way and in rock and gravel quarrying. Of particular interest, perhaps, to mining men are the problems of gold placer deposits and water supply. Geophysical work on gold placers is of especial interest because of the present expanded activity in all phases of gold mining. The development of a suitable water supply at, an economical cost is often of prime importance in insuring a successful mining venture. Particularly is this true in the arid Southwest. How-ever, the use of geophysical work in water supply is not confined to the needs of mining development.

Jan 1, 1933

BLOCK CAVING HAS BEEN DEVELOPED to a high degree of efficiency in the last two decades and more particularly since World War II. At the Jeffrey mine of Canadian Johns-Manville Co., in the Eastern Townships of Quebec, several innovations have increased production and decreased costs. Asbestos ore is produced at the rate of 10,000 tpd from an underground operation supplemented by a large open pit that has been mined since 1881. The orebody consists of asbestos veins in a fractured and serpentinized peridotite. Hardness and structural strength of rock vary from soft shear zones at one extreme to a small amount of hard granitic inclusions at the other. In general the ore is weak and deteriorates on exposure to air, so that it is difficult to maintain underground openings for any period of time. Permanent workings are lined with concrete and temporary ones are driven mini- mum size and supported with steel sets as required.

Jan 5, 1954

By Hans W. Schreiber, David W. Neuhaus

INTRODUCTION The Sunshine Mining Company's 16-to-1 silver deposit and mine project are located 384 kilometers (240 miles) southeast of Reno and 360 kilometers (225 miles northwest of Las Vegas, near Silver Peak in Esmeralda County, Nevada, at an elevation of about 2,300 meters (7,000 feet). The deposit was being developed, in 1980, with an anticipated mining and milling rate of 150,000 tons per year (500 tons per day). Mining is by underground, blast-hole open stoping with rubber-tire haul-age out of the mine to a straight cyanide plant about 5.5 kilometers (3.5 miles) from the mine. The product is a gold-silver dore which may be further refined at Sunshine's new refinery in Kellogg, Idaho. The cash required for investment was obtained through the sale of $25 million worth of 6 l/2h silver-indexed bonds. Some $15.0 million were directed toward development of the 16-to-1 Mine. These bonds, which were underwritten by Drexel Burnham Lambert of Chicago in April of 1980, are redeemable on or after April 15, 1985 or payable at maturity on April 15, 1995 at the greater of either $1,000 or the market price of 50 ounces of silver. Behre Dolbear acknowledges the kindness of the Sunshine Mining Company (Sunshine) for allowing the presentation of the subject material for this Case Study. APPLICABILITY AS CASE STUDY Reasons for Choosing 16-to-1 The reasons for choosing the 16-to-1 Mine as a case study follow: 1. The project is simple and compact. 2. The mine is small -- thus relevant to other contemplated precious metal operaions in the western states. 3. The areas of risk are readily identifiable. 4. A change to project financing was under consideration. 5. A substantial decline in the price of silver was experienced during development. 6. Behre Dolbear undertook one of the first feasibility studies of The 16-to-1 and thus has some familiarity with the project. Historical Summary The following history serves as a setting: 1. Late 1920s -- minor "production"(?) via shallow pitting. 2. Mid-1930s -- neighboring Nivlok Mine successfully put into production. 3. Late 1950s (?) -- Callahan Mining Company acquired rights and drilled -- results inconclusive; Callahan turned property back to Arthur Baker, who had originally interested Callahan in 16-to-1 on the basis of its similarity with Nivlok Mine.

Jan 1, 1985

By Robert T. Pring

In addition to the humanitarian aspects of a dust-control program, certain economic benefits are becoming more fully recognized and now furnish a greater incentive to the mill operator to eliminate the dust from his plant. It is well known that a favorable working environment promotes increased efficiency and improves the morale of employees, with a consequent decrease in labor turnover rates. One progressive mining company' estimates its direct and indirect labor turnover costs at from $40 to $50 per man; for skilled labor, such as machine operators, the cost may approach $100 per man. While these figures may not be typical of every plant, they do indicate a potential savings in operating costs. Dust signifies waste; its elimination decreases maintenance costs of mechanical and electrical equipment; its recovery is often justified from the standpoint of values contained in the collected material, although in large-scale milling operations handling low-grade ore this may not be an important factor, Perhaps the most significant trend in industrial sanitation is that dust-control equipment and procedures are becoming recognized as integral parts of the mill flowsheet. Exhaust ventilating systems are now afforded equal care in design and maintenance to that given other machinery more closely related to the Process. Methods of Dust Control "Dust control" is a general term descriptive of a number of methods used singly or together to prevent particulate atmospheric contamination. These methods are: in order .of their desirability, as follows: 1. Change of process. 2. Isolation of process. 3. Wet methods. 4. Ventilation. a. Local exhaust ventilation. b. General ventilation. 5. Personal respiratory protection. In ore-concentration plants it is seldom prac tical to change a process to eliminate the dust it creates It is possible in some cases to isolate a particular dust-producing operation from the rest of the plant, provided that constant attention on the part of the operators is not required. Frequently water is used in fine crushing and fine grinding, primarily to facilitate the processing of the ore and incidentally to allay the dust produced. Wet methods, however, are not feasible in coarse and secondary crushing operations, because of the relatively great volume of water required in instantly wetting each freshly fractured rock surface. Such quantities of water would entail conveying and storage difficulties. Local exhaust ventilation is the most effective and most commonly applied control measure, wherein directional air currents through the zone of dust production draw the contaminants into a duct system. Unfortunately, only a limited amount of reliable information on exhaust ventilation is available.2-5 of necessity these publications are rather general, being primarily concerned with engineering fundamentals. While many organizations have successfully

Jan 1, 1943

By J. R. Long, T. R. Graham, R. G. Feustel, R. S. Dean

THE comprehensive study of the copper-manganese-zinc alloy system in the Bureau of Mines Laboratories has so far been principally concerned with alloys that lie within the alpha solid solution field of the system. Two regions, one centering about 65 per cent copper, 10 manganese and 25 zinc, and the other centering about 70 per cent copper, 20 manganese, 10 zinc, have been carefully examined.1,2 These have indicated that when the alloys are made with electrolytic manganese considerable amounts may be readily introduced and that the strength and hardness are increased without excessive losses in ductility. In the course of the work of establishing the limits of the alpha solid solution range,3 enough of certain of the alloys was prepared to permit determination of their physical properties at a future date. The 60 per cent copper alloys concerned here are part of that series. They cross through the alpha field and into the adjacent alpha plus beta and alpha plus X fields, and are of interest because they offer some information on the effects of manganese on alloys lying in these fields. COMPOSITION AND FABRICATION OF ALLOYS The chemical composition of the alloys involved is given in Table I. They were intended to contain 60 per cent copper with manganese increasing from 5 to 25 per cent in 5 per cent steps and zinc decreasing [ ] from 35 to 15 per cent. The analyses are so close to the intended composition that the alloys will be referred to hereafter by their nominal compositions. They were finished into sheet by cold-rolling and intermediate annealing procedures calculated to produce sheet 1/16 in. thick, cold-reduced by 20, 40, 60, and 80 per cent in thickness. Physical properties were determined on standard flat tensile specimens with 4-in. gauge length, although the test gauge section used was 2 in. The properties were obtained on cold-worked material and on material annealed at temperatures ranging from l00° to 1500°F. after 60 per cent cold reduction. Since an annealing temperature of 1200°F.

Jan 1, 1946

By R. H. Fillnow, D. J. Mac

IT has been demonstrated that alloys in systems structurally analogous to steel undergo reactions during heat treatment similar to those of steel, and yet very little work has been done on such systems, particularly from the standpoint of isothermal transformation. The literature shows that most of the isothermal work has been done on copper-alu-minum alloys.'-3 One paper has been reported on a eutectoid copper-silicon alloy,' and one on iron-nitrogen alloys.' There are no published reports of previous investigations on the isothermal transformation of a eutectoid beryllium bronze. At least two papers have been reported on isothermal age-hardening phenomena in beryllium-copper alloys of lower beryllium content.5,6 No information on eutectoid transformations in this alloy is given in Rimbach's book, "Beryllium." ' This paper reports the results of an investigation on the isothermal transformation characteristics of a eutectoid beryllium bronze. Materials Used and Procedure The eutectoid beryllium bronze used in this investigation was centrifugally cast at the Ampco Metal Co., Inc.. Milwaukee. Wis. A master beryl-lium-copier alloy, purchased from the Brush Beryllium Co., was used to make the beryllium addition to the copper. The alloy was melted under a protective carbon cover and Centrifugally cast into a graphite mold preheated to 920°F. Some trouble with segregation of beryllium in the melt was encountered but was eliminated by violent stirring during melting and pouring. Since very thin .specimens were used for the various heat treatments, only one casting of the four prepared was necessary for the complete isothermal study, thus eliminating any discrepancies caused by a change in composition. The analysis of this casting was 94.035 pct copper and 5.965 pct beryllium. A slight trace of iron was found. The castings were sawed into specimens approximately 3/32 in. in thickness. The specimens were first given an "austenitizing" heat treatment at 788°C, well within the single phase beta region, in a vertical tube furnace. The specimens were then quenched individually into an adjacent molten salt bath and held there for a definite time, after which they were quenched into water at room temperature. Temperature was held to ± 2°C in the salt bath. No homogenizing treatment was given the specimens other than the soak at 788°C. Despite the fact that this was a cast alloy, no evidence of segregation or coring was found in the microstructure of any specimen, either as cast or as heat-treated. Upon completion of the heat treatment, the speci-mens were subjected to metallographic examination

Jan 1, 1951

By C. Burton Clark, J. Spotts McDowell

Refractories are defined as "materials having the ability to retain their physical shapes and chemical identities when subjected to high temperatures," or as "nonmetallic materials suitable for the construction or lining of furnaces operated at high temperatures." While resistance to "high" temperatures is thus the primary requirement for refractory materials, it is by no means the sole requirement. They must be able to withstand thermal shock resulting from rapid heating or cooling; other stresses induced by temperature change; pressures from the weights of furnace parts or contents; mechanical wear (abrasion) resulting from movement of furnace contents; and chemical attack by heated solids, liquids, or gases. Refractories of many kinds are needed for the many and widely diversified industrial applications. Those in greatest demand are classified on the basis of composition or properties into a few main groups, known as alumina-silica, silica, basic and insulating refractories. In each of these groups there are several classes. In addition to those included in the main groups, there are various special refractories, including silicon carbide, carbon, zircon, zirconia, alumina, and several others. Alumina-silica refractories comprise two main divisions: fire clay and high-alumina. The alumina content of fire-clay refractories covers the range from about 45 pct to 18 pct, and the silica content from 50 pct to 80 pct. The alumina content of fired high-alumina refractories ranges from about 99 pct to 45 pct, and the silica content from about 0.5 pct to 50 pct. Silica refractories of the different classes contain 94 pct to 97 pct silica. Basic refractories include periclase (magnesite), chrome spinel, forsterite, and dolomite. Refractory materials, including insulating firebrick, are supplied mainly as preformed shapes. Other products include bonding mortars and high temperature cements, ramming mixtures, plastic firebrick, hydraulic setting castables, dead-burned grain magnesite, and dead-burned dolomite. Refractory brick are classified on the basis of their physical form as Standard Sizes and Special Shapes. The Standard Sizes are brick of certain definite sizes and relatively simple design which are used in sufficient amounts to permit quantity production. The brick most widely used are the standard 9 in. X 4 ½ in. X 2 ½in. and 9 in. X 4½in. X 3 in. straights and corresponding series of sizes. All brick of nonstandard dimensions are regarded as "special shapes." They include a wide variety of brick regularly used for specific services, such as baffle tile for boilers, checker brick for regenerators, and others; together with shapes of special design manufactured on particular orders from designs submitted by the user. Not included in the broad classifications of Standard Sizes and Special Shapes are several specific-service refractory products, usually made by companies which specialize in their manufacture, or in some cases by the consumers themselves. These products include

Jan 1, 1960

By E. F. Ketterer, D. B. Collyer, A. B. Wilder

AISI constructional alloy steels are a series of steels in which a numbering system signifies the chemical composition limits. SAE (Society of Automotive Engineers) and AISI (American Iron and Steel Institute) use basically the same numbering system. The steels contain, in part, alloy additions of chromium, molybdenum, nickel, and vanadium. They are used widely in the automotive industry but have not been adopted for high temperature service. The purpose of this investigation was to study changes in microstructure observed in typical AISI constructional alloy steels in the welded and un-welded conditions after exposure for 34,000 hr at 900" and 1050" and, in several instances, 1200°F. The tensile and creep rupture properties after exposure for 10,000 hr were also evaluated. The investigation is a continuation of the work previously discussed. Little was known concerning the existence of graphite in medium or low carbon steels before 1943. It is important to note that continued exposure at elevated temperature is required in order to develop graphite in steels. Interest in the presence of graphite in steel, and also in changes in the properties of steels after long service at elevated temperatures, developed after 1943 when a failure of a welded joint of high temperature piping was associated with the graphitization of a relatively low carbon content steel with 0.50 pct Mo,8,0 Numerous investigations have beeen made in recent years studying the relationship of this type of failure to changes in properties. Attempts have been made to evaluate the performance of a number of steels, particularly in the heat-affected zone of welds. It was the unfortunate failure of a weld-heated zone in high temperature piping in the steam-power industry which focused attention upon possible failures, and upon the need for improved steels for high temperature piping service. Investigation by the National Tube Div., U. S. Steel Corp., Lorain Works, has included a wide variety of steels in an attempt to learn the effects of numerous factors and elements upon the long time performance of steels, although many of the compositions studied will never be used at elevated temperatures.1,4-7 Included were the well established AISI steel series, which offered opportunity to test moderately high carbon content steels as well as observe the effect of nickel, chromium, molybdenum, etc., upon the properties of these well known steels. The properties of the AISI steels were also studied for comparison with the previously reported properties of the Cr-Mo steels, now used by the steam-power industry.5,7 Materials and Testing Procedure The AISI alloy steels in Table I were exposed for 10,000 and 34,000 hr at 900°, 1050°, and 1200°F.

Jan 1, 1958