Search Documents

By E. Hoek

INTRODUCTION Rock slope stability research has been in progress for the past four years at the Royal School of Mines in London under the sponsorship of a consortium of 23 companies* with interests in open pit mining. This paper reviews the principal aims and achievements of this research project. In order to assist the reader in following these details, the basic philosophy underlying the formulation and direction of this research project is discussed. DISTRIBUTION OF RESPONSIBILITY In open pit mining, the economic necessity of keeping waste rock removal to a minimum generally means that the mine slopes have to be excavated to the steepest possible slope angle. On the other hand, excessive steepening of these slopes can induce failures, which may negate the economic benefits that have been aimed at and which may also result in loss of life and damage to equipment. Consequently, where slope failures are likely to prove to be a problem, an evaluation of the stability of the slopes to be created should be included as part of the overall pit design. How is the stability of a rock slope evaluated? When this question was examined, during discussions on the research policy to be followed at the Royal School of Mines, it was clear that relatively few satisfactory techniques were available in a form that would be comprehensible and therefore useful to the practical mining engineer. It was recognised that the research project must be directed towards two distinct aims: a) The evaluation of existing techniques for rock slope stability analysis and the provision of new techniques where these existing methods were found to be inadequate and b) The presentation of the results of this evaluation and research in a form that would be useful to engineers without specialist training in rock mechanics. It was soon realized that a university based research team, however large and efficient, could not achieve these aims without the co-operation and assistance of mining engineers,

Jan 1, 1972

By E. S. Grumell

The correct sampling of coal and coke is becoming important to an ever increasing number of producers and consumers. This, therefore, may be an opportune moment to examine where we stand with regard to existing and proposed methods. In this paper an attempt will be made to review, as briefly as possible, some of the considerable amount of painstaking research which has been done in the last 10 years, and which has unquestionably led to a much better understanding of the subject. In so doing we shall try, on the one hand, to make clear where substantial progress has been made, and on the other hand, to draw attention to points that require further investigation. The paper is divided into sections in order to emphasize the major divisions of the subject; further, in order to retain this emphasis, detailed consideration of some of the points has been relegated to appendixes. No attempt has been made to give a complete survey of the literature, as this has already been done by L. A. Bushell.2 The following abbreviations will be used: A.E., average error; P.E., probable error; S.W.R., size-weight ratio; B.S.I., British Standards Institution. Section 1.—Cost It has often been stated that the cost of sampling should bear some relationship to the value of the product, and since coal is a relatively cheap raw material it would be a major error to specify, for ordinary commercial purposes, elaborate and costly methods of sampling which nobody would adopt. Specifications must be of such a nature that they will be used. We believe that one of the achievements of the last 10 years has been to reduce the cost of sampling. There is, however, another point to be considered; via., that the cost of sampling should bear some relationship to the value of the investigation. Correct sampling is a cog (possibly a small one) in the wheel

Jan 1, 1940

By H. S. McKnight

One phase of Canada's rapid development in mining and metallurgy during the past few years has been the creation of Canadian Copper Refiners Ltd., and the establishment of its modern electrolytic copper refinery at Montreal East, Quebec. Canadian Copper Refiners Ltd. is made up of three well-known metal firms whose combined activities cover the entire industry from the mine to the market. They are Noranda Mines Ltd., Toronto, Nichols Copper Co., New York, and British Metal Corporation, Ltd., London. Noranda Mines is the principal owner and provides the greater part of the raw material received by the refinery for treatment. Nichols Copper Co. designed and built the plant and is operating it under contract. British Metal Corporation acts as sales agent and markets the refinery's products. Montreal East was chosen as the site of the new refinery only after a careful survey had been made of the entire eastern part of Canada. The location chosen offers many advantages, chief of which arc the relatively low costs of power, labor, fuel and bupplies, and the fact that it is situated on Montreal harbor, the nearest seaport to the points of origin of the ram materials. All incoming material is received by rail. A majority of the plant's product is exported through the port of Montreal to European markets, being handled to the docks in railroad cars. A large proportion of the product is delivered by means of an industrial railway to the adjacent rolling mill of the Canada Wire & Cable Co., Limited. The refinery was designed to treat primarily the copper produced by Noranda Mines, Ltd. and Hudson Bay Mining &. Smelting Co., Ltd., and its rated capacity is 75,000 short tons per year. A general layout of the plant is shown in Fig. 1. Its capacity can be readily doubled, as shown by the dotted lines. Figs. 2 and 3 are sections taken through the furnace department and the tank house respectively. Except for the main office and laboratory and an auxiliary building containing the stores, warehouse, change rooms, compressor room and machine shop, the entire plant is under one roof. The type of building construction consists of reinforced concrete foundations supported on concrete piles, a steel structure covered with Robertson Protected Metal siding and a 3-in.

Jan 1, 1934

By L. L. Handy

Two equations are compared for calculating imbibi-tion rates of water into porous media. A linear relation was found to apply when the square of the volume of water imbibed was plotted against time for water imbibing in natural rock materials. The effect of adsorbed organic materials on surface wettability was determined from measurements of rate of imbibition, water saturation and water permeability. INTRODUCTION An understanding of the mechanisms by which water displaces oil from porous media requires an understanding of the role of capillary forces in the displacement process. The capillary forces are determined by properties of the water-oil-solid surfaces. Consequently, some measure of the surface properties of reservoir rocks is necessary if displacement behavior in oil reservoirs is to be predicted from laboratory measurements. Several experimental procedures have been proposed to assign quantitative wettability indexes to reservoir rock surfaces. The most recent of these proposals are those of Bobek, Mattox and Denekas' and Amott.' These indexes are designed to show a continuous variation from the preferential oil-wet to the preferential water-wet systems. They require measuring some property of the rock which is a function of surface wettability. The quantities are measured on unaltered core material and compared with values obtained for known oil-wet and water-wet extremes on the same material. These methods are useful but are semi-empirical in nature. They have the disadvantage that the measured quantities may be functions of other variables in addition to surface wettability. Some understanding of the behavior of water-oil-rock systems may be obtained from studies of the simpler water-air-rock systems. Surfaces of a given wettability are more easily maintained for the latter. Also, certain approximations can be made for the flow of water and air which are not justified for water-oil flow. The theoretical and experimental work discussed in this paper is part of a study of the role of capillarity in the dynamic displacement of air by water. The expec- tation is that observations for the water-air system will lead to generalizations which are applicable to water-oil systems. THEORY Imbibition is defined as that process by which one fluid displaces another from a porous medium as a result of capillary forces only. Differential equations have been derived to describe the displacement of oil by water during imbibition, but these equations have not been solved.".' With certain assumptions, however, solutions are possible for water-air imbibition.

By C. M. Loeb, T. E. Norman

THE use of ball, rod and tube mills for grinding ore, cement and other materials has grown so rapidly during the past forty years that the world's annual consumption of ferrous grinding media for these mills is now estimated to be between one half million and one million tons per year. Ferrous grinding balls constitute the major portion of this tonnage. Obviously they represent sufficient value to justify thorough studies' of the factor sgoverning their performance. The selection of grinding balls is governed principally by: I. Quality (wear resistance, impact resistance, soundness, and the like). 2. Sources of supply and delivered cost. 3. Grinding characteristics or efficiency in the ball mill. This paper deals principally with the quality of ferrous grinding balls. In the study of these factors certain data relative to the fundamental nature of ball wear in ball mills have been obtained. These data are also presented and discussed briefly. THE DEVELOPMENT OF A SUITABLE WEAR TEST A study of the fundamental factors governing the quality of grinding balls has been hampered seriously by the fact that a competent test has, in the past, involved the purchase of several hundred tons of balls of a specific type which were then run in one or more ball mills for a period ranging from several months to several years' duration. Often, during the period of test, it became necessary to change operating conditions or the character of the ore fed, to the test mill with the result that the rate of ball consumption changed and the test figures became of little value. Under such circumstances, progress in the development of better grinding balls, has been necessarily slow. Economic factors and variations in the quality of balls produced by different sources of supply generally make it necessary for each mill operator to determine for himself the most suitable type of balls for his mills. In our own ball mill grinding operations at Climax, Colo., we were faced with this problem. After we had run a few large scale wear tests at considerable expense we decided to investigate the possibilities of a small scale wear test which would be capable of testing numerous types of balls within a relatively short time. The most important requirement of any test is, of course, that it give results which can be used to predict accurately the wear in full scale operations. It was known that Ellis and his associates1,2 had developed a method of testing grinding balls by small scale tests run at the Ontario Research Foundation. Ellis' method of testing was used as a starting point in our investigations. In the course of our tests a number of modifications of the original method were found to be desirable so that, by an evolutionary procedure, a method of small scale

Jan 1, 1947

By C. B. Alcock, R. A. Oriani

Some simple models of solutions are described; these include the regular solution, the subregular solution, and the quasichemical model. The assunzption underlying these models, the physical signzficance thereof, and the experimental manifestations are discussed. Examples are presented from the fields of liquid and solid metallic solutions, liquid slags, mattes, liquid and solid ionic solutions, and mixed carbides to show under what conditions and for which systems these solution models are fair descriptions. The deviations of real solutions from the models are of theoretical interest. Some such deviations, both for dilute and for concentrated solutions, arc pointed out and their Physical sigtzzficance discussed. DURING the past half century there has been a gradual accumulation of thermodynamic data for systems of interest to the metallurgist. There remain many gaps in the data, however, and the metallurgist must often face the problem of estimation of thermodynamic quantities where measured values do not exist. One might hope that the experimental progress would be matched by theoretical advances which would make such estimations possible with a high degree of confidence. However, theoretical progress has been disappointingly slow even for the simplest kinds of solutions, and since the multicomponent systems in which the metallurgist is interested are very complex, one cannot expect theory to be of much help to the metallurgist. In this situation, therefore, it seems worthwhile to examine some simple models of solutions from two points of view: firstly, to see if such crude models represent the thermodynamic facts in as many types of solutions as possible sufficiently well for the needs of the metallurgist, and secondly to see what the deviations from such models show to be important for consideration by theorists. BOND ENERGY MODELS OF SOLUTIONS The simple models that we will examine from these points of view may be termed statistical models, in that they are concerned with the thermodynamic consequences of some simple assumptions about the energy of an assembly of atoms, molecules, or ions, and do not inquire into the physical basis of the interaction. The underlying assumption of these models is that the energy of an assembly of molecules (by which we include also atoms or ions) is given by the sum over all interaction energies of molecules taken two at a time; we will discuss only those models in which the pairwise interactions are restricted to those between nearest neighbors. Thus, in a pure substance of bond energy EAA, the internal energy (with respect to some specific reference state) will be expressed as NAA EAA where NAA is the number of nearest-neighbor pairs. A solution of molecules A and B will be characterized by NAA EAA + NBB EBB + NAB EAB where the Eij represent the bond energies of the nearest-neighbor i-j pairs. If one assumes that the EAA and EBB are the same in the pure components as in the solution, and that the coordination numbers in the two pure substances and in the solution are the same, then the energy of the solution with respect to the pure components (i.e., the energy of solution) is a function of the following linear combination of the bond energies: EAB - 1/2(EAA +EBB) = w. The thermodynamically ideal solution is defined as one in which the activity of each component is equal to the mole fraction of that component at all concentrations and all temperatures. It follows that

Jan 1, 1962

By C. P. Proctor, J. B. Morrow

With numerous plans under consideration for coal classification, and with the advent of the Bituminous Coal Code, the intelligent sampling of coal has become increasingly important. To us it is rather significant that there have been very few fundamental studies of coal sampling in American technical literature since those of E. G. Bailey, which appeared in the Journal of Industrial and Engineering Chemistry in March, 1909. He covered the subject up to that time so thoroughly and in such an excellent manner that perhaps many other later students have felt that they could add very little to his findings. The recent studies of the British Engineering Standards Association have indicated the possibility of a somewhat different interpretation of Bailey's results, permitting the taking of smaller samples, and perhaps it will now be helpful to reopen this question. C. W. H. Holmes, in an informative series of articles on coal sampling recently published in Colliery Engineering, makes two rather interesting statements, as follows: It is scarcely surprising to find a lack of interest and knowledge regarding the sampling of coal not only in the mining industry itself but also among consumers of industrial fuel: at its best coal sampling is a dirty business, regarded as a nuisance and an expense by the commercial man, and usually as a nuisance and nothing else by the chemist. The writer can conceive only two classes of people who have never experienced any difficulty in obtaining representative samples of coal from wagons; those who have never tried to, and those who have never had the necessity or desire to check the accuracy of their work. The primary purpose of this paper is to present some tabulated data of the more significant results of a sampling investigation undertaken during the last four years to obtain certain fundamental data on the variables connected with coal sampling and to point out that often assumptions have been made that are not in accordance with the facts. One of the standard sampling methods states:

Jan 1, 1936

By P. W. Ramsey, E. J. Boyle, E. A. Anderson

ONLY a few zinc-rich alloys are in commercial use today, and these depend largely upon solid solution effects for their desirable properties. Typical examples are rolled alloys containing about I per cent of copper, with or without additions of elements such as magnesium,1 and die-casting alloys containing about 4 per cent of aluminum with small amounts of magnesium and sometimes copper.2 A number of elements are capable of forming alloys with zinc, which do not enter into solid solution except in limited degree. The present paper considers one such system, zinc-titanium, in which alloys having potentially useful properties in the rolled form were found. ZINC-TITANIUM SYSTEM The zinc-rich portion of the zinc-titanium diagram, as determined by standard methods in this laboratory,3 is shown in Fig. I. The portion of the diagram of significance in the present work extends from 0 to about 0.5 per cent titanium. Gebhardt4 places the eutectic at 0.45 per cent, but the evidence in favor of the composition given in Fig. I is considerable. The solid solubility of titanium in zinc is very low indeed and possibly places these alloys in a somewhat different category from the commercial alloys previously mentioned. ALLOY PREPARATION All of the alloys used in this work were prepared with titanium metal of 98.9 per cent purity. In most cases high-purity zinc (99.99 per cent) was used but sufficient work was done later to show that zinc of about high-grade composition would yield approximately equal results. Best practice in alloy manufacture seemed to be to prepare a zinc-titanium hardener by adding about 4 per cent of titanium metal to molten zinc and holding under a boric acid cover, with frequent stirrings, at 750°C. until the titanium had dissolved. The desired titanium content could readily be obtained in the final alloy by adding the calculated amount of this hardener. The alloys proved to be quite stable in composition, unless overheated, and, with reasonable temperature control, required no cover or flux to prevent loss of titanium content by oxidation. HOT-ROLLING TESTS Three alloys containing, by analysis, 0.05, 0.12, and 0.23 per cent titanium were selected for preliminary study. Slab cross sections revealed a marked grain refinement* (Fig. 2) in the two alloys of highest titanium content. Cast unalloyed zinc has a columnar grain structure similar to that shown for the alloy of lowest titanium content but without the scatter of small equiaxed grains at the center.

Jan 1, 1944

By B. L. Averbach, Morris Cohen, S. A. Kulin

The martensitic transformation can be initiated by elastic stresses at temperatures above M. in a steel containing 20 pct Ni and 0.5 pct C. Shear strains and normal tensile strains acting on a potential habit plane promote the transformation but compressive strains oppose it. THE strain sensitivity of the martensitic transformation has long been recognized. It is now well known that martensite formation can be induced by plastic deformation at temperatures below, and not too far above, the M, point.' However, the exact role of elastic vs. plastic strains and of the concomitant stresses has proved to be a very elusive matter. Many investigators2-' of the steel hardening reaction have made use of the stresses resulting from volume changes to account for such observations as the existence of retained austenite and its variation across the section of a bar, the change in the amount of retained austenite with quenching rate, and the self-stopping nature of the transformation when the cooling is stopped. The effect of applied strain as an independent variable has been studied in 70 pct Fe-30 pct Ni alloys by Scheil7 and McReynolds.8 Some data are also available for lithium and Li-Mg alloys,9 Cu-Zn,10 Cu-Sn and Cu-A1 alloys," and aus-tenitic stainless steels."-" It has been found that martensite formation can be induced isothermally, even at temperatures above M,, by mechanical deformation of the parent phase. The competitive nature of plastic yielding by slip and by the martensitic reaction has been depicted by Scheil.7 Basically, Scheil postulated that: 1—at temperatures not too far above M, (where austenite is less stable than martensite), a critical resolved shear stress (within the elastic range) is required to promote the transformation to martensite; 2—at and below M,, the austenite lattice becomes mechanically, as well as thermodynamically, unstable and shears over spontaneously into martensite without the application of external stress; and 3—at temperatures sufficiently far above M8, the critical resolved shear stress for martensite formation increases to a level above that required for slip, and plastic flow then supersedes the transformation when external stress is applied. Scheil's concepts were tested by McReyno1ds8 ho found no change in the elastic moduli (measured both statically and dynamically) of 71 pct Fe-29 pct Ni alloys in the vicinity of the M, temperature. Since the moduli did not approach zero or become negative on cooling to M,, it was concluded that the austenite lattice does not become mechanically unstable at M2, as postulated by Scheil. McReynolds also reported that M, is not raised by elastic stresses. Accordingly, plastic deformation was considered to stimulate the transformation by generating martensite nuclei in the distorted regions of the parent phase. The above issues with regard to the role of applied stress require clarification, if a basic understanding of the martensitic transformation is to be obtained. For example, in the reaction-path theory,'"," it is postulated that strain embryos exist in the austenite that provide part of the activation energy for the nucleation process. These embryos are visualized to be regions of localized strain in which the atoms in the austenite lattice are displaced part way along the path to their ultimate positions in the martensite. Consequently, it would

Jan 1, 1953

By D. S. Eppelsheimer, D. N. Williams

The cold rolled textures of iodide titanium and of three samples of commercial titanium were examined using the Schulz-Decker Geiger counter technique. The iodide titanium and two of the three samples of commercial titanium showed a (0001) [1010] texture rotated 30' toward the transverse direction about an axis in the rolling direction. The third sample of commercial titanium showed a double texture. THE metals of the hexagonal system tend to deform similarly if the c/a ratios are similar. Thus titanium, zirconium, and beryllium, with c/a ratios of 1.601, 1.590, and 1.570, respectively,l should have similar cold rolled textures. The cold rolled texture of high purity iodide titanium has been described as (0001) [1010] rotated 30" toward the transverse direction about an axis in the rolling direction.' The texture of zirconium has also been reported as (0001) [1010] with a transverse rotation from the ideal position of approximately 30" about an axis in the rolling direction." This texture differs from that reported for titanium however since a continuous spread of (0001) poles toward the transverse direction was reported rather than distinct (0001) maxima 30" from the rolling plane normal. Beryllium has a texture similar to that of zirconium although the angle of transverse rotation of the (0001) poles is much less.' These three metals thus show a common type of cold rolled texture, as yet unexplained, which can be described as (0001) [1010] with various degrees of rotation toward the transverse direction about an axis in the rolling direction. Since titanium showed the greatest degree of rotation from the (0001) [1010] position, the cold rolled texture of titanium was re-examined using a semiquantitative Geiger counter X-ray technique to obtain more accurate experimental data from which a theoretical interpretation of this new type of hex- agonal rolling texture could be developed. The cold rolled textures of iodide titanium and of three samples of commercial titanium were determined. Table 1 gives the analyses of the titanium samples. Experimental Procedure Preparation of Samples: Prior to the final rolling operation each of the samples was given an initial reduction of approximately 50 pct and annealed to remove the gross effects of any previous treatments. Samples were annealed in vacuum, high purity helium, and air to determine whether annealing atmosphere had any effect on the cold rolled textures developed. All samples were annealed 1 hr at 800°C. Grain size determinations were made using the formula, 1.075 in which n is the number of grains counted in an area A (in sq mm) and M is the magnification of the area counted.' This formula gives the diameter between opposite flats assuming hexagonal grains. At least three areas containing more than sixty grains each were counted in each grain size determination. Rockwell B hardness readings were made on the annealed samples. The results of the measurements of

Jan 1, 1954

By P. G. Shewmon

THIS paper is concerned with the redistribution of a second phase when a 2-phase solid alloy is annealed in a temperature gradient. An examplewhich is discussed in detail is the redistribution of carbides in a low-carbon steel annealed in a temperature gradient below the A, temperature. As a result of such a treatment, the carbides at the cooler side disappear, while those at the hotter side grow in size. In a 2-phase zirconium-hydrogen alloy, the amount of hydride will tend to be increased at the cold end and decreased at the hot end. That such an effect can occur in solid metals is not generally appreciated. However, with the trend toward higher operating temperatures in several fields, this phenomenon will become more important in the future. Actually, such effects should be rather common in the core of nuclear power reactors where the op- erating temperatures are high and temperature gradients are an order of magnitude higher than in previous high-temperature applications of alloys. The purpose of this paper is to point out the existence of such an effect, to discuss the manner in which one predicts whether a redistribution of the second phase will occur in a given system, whether the second phase will go to the hot or cold face, and how rapidly the redistribution will occur. One aspect of this problem has been discussed by pfam and Wernick2who considered the migration of a small liquid region through a solid. In their case, the diffusivity in the liquid is much larger than in the solid and they have interpreted their results successfully by using Fick's first law as the flux equation in the liquid, and taking the concentration gradient from the phase diagram. For all the cases they have studied, this type of analysis predicts that the liquid region migrates from the cold end to the hot end, and this is what was found ex-

Jan 1, 1959

By Paul A. Beck

While the recrystallization properties of most of the practically important metals are known in considerable detail, those of lead are still relatively little known in spite of some valuable contributions in recent years. This condition probably is due to the difficulties involved in applying the usual methods of investigation. The microscopic method of discriminating between the elongated deformed grains of the familiar lenticular shape and the equiaxed recrys-tallized grains is not successful with fully refined lead: lenticular grains cannot be seen under the microscope with any amount of deformation whatever. The probable cause of this phenomenon was recognized long ago. With large deformation the time of recrystallization at room temperaturc is shorter than the period of preparation of the specimen for microscopic examination; with small deformation the deformed grains arc not noticeably elongated in the first place. However, with small cleformation the migration of the grain boundaries can be observed. The only systematic investigations yet published on the recrystallization of lead, those by R. S. Russell, 1-3 make use of the conditions just described. Russell considered recrystallization completed when no further migration of boundaries could be observed. A serious objection to this method arises from the fact that there is no evidence to support the view that grain-boundary migration results only from recrystallization. If such migration does result from other sources after recrystallization is completed—after the deformed grains have been replaced by new unde-formed grains—the "time of recrystallization" as determined by Russell may be too long. Furthermore, the method is subject to the above.-mentioned limitation because of the unavoidable period of preparation of the sample. According to Russell, even with the fastest technique 5 min. clapsed before the deformed samples were ready for examination, and consequently no reearystallization time shorter than 5 min. could be measured. The lack of success in detecting the recrystallization of lead by the usual hardness or tensile tests is again caused by the time necessary for

Jan 1, 1940

By Robert Wamsley, W. E. Jones

One of the earliest problems in the life of any community is the provision of an adequate supply of water sufficiently free from all types of contamination to be suitable for domestic purposes. Generally speaking, the location of most communities is determined to a great extent by the availability of an adequate supply of satisfactory water. For a mining camp, that consideration cannot be foremost. Here, the ore takes first place, and the men who mine it must do the best they can under the existing conditions. If there is no local source of water, it must be brought from some distant source or must be found by sinking shafts or drilling wells. Fortunate indeed is the mining company that discovers a commercially valuable ore deposit beside a never failing creek full of pure water, with sufficient water rights available. because the acquisition of water in any other manner nearly always involves not only a considerable period of time but the expenditure of considerable money. The experience of Climax Molybdenum Co. demonstrates the measures that sometimes are necessary in order to provide a suitable supply of water. The Climax mine and mill are on the Continental Divide! about 13 miles northeast of Leadville. The elevation of the domestic part of the camp varies from a minimum of 11,320 ft. to a maximum of approximately 11,550 ft. above sea level, and, as is common at such altitudes, the near-by streams that might be suitable for a water supply are small and intermittent, usually flowing only during the summer months. The only streams of any size in the immediate vicinity of Climax are the Ten Mile and Arkansas Rivers The headwaters of Ten Mile River are on the Company's property, and its water has been used for the domestic supply. The headwaters of the Arkansas River are about 2 miles distant and have not been used as a source of supply by the company. During the past 11 years of the production of molybdenum at Climax, the number of families living there has increased from about 45 to 283, and the population has increased from about 200 to 1200 persons. Consequently, the capacity of the water-treatment facilities, and the amount of water available, had to be increased to meet the requirements of the camp. As early as 1932 it was recognized that the water in Ten Mile River would not continue to be adequate for domestic purposes and after considerable discussion it was decided to drive a drift through the major fault in an effort to find additional water. This drift was completed in 1935 and tapped sufficient water to make the supply adequate. This water was treated in a tank underground, where lime was added, and was then piped into the domestic supply lines. At about the time this line was completed, the presence of fluorine in harmful concentrations was discovered in the water. This problem was submitted to the International Filter Co. and in November 1937 a plant of its design was put in operation for treating the water to remove the fluorine. This plant proved entirely successful,

Jan 1, 1946

By H. D. Outmans

The mechanics of filtration are described by a theoretical-empirical nonlinear diffusion equation which, under certain circumstances, may,be linearized and then solved explicitly. For filtration under static conditions linearization leads to a boundary value problem analogous to a heat flow problem with a known explicit solution. The corresponding solution for static filtration is compared with published experimental data. Under dynamic conditions filtration takes place in three successive stages. During each of these the rate of filtration and/or the thickness of the filter cake are different functions of the filtration time. The proposed mechanism explains the observed high resistance of dynamically deposited filter cakes against erosion and also the connection between filtration rate and viscosity of the drilling fluid. Several of the quantities governing dynamic filtration have no counterpart in the static filtration mechanism. The static filtration rate is, therefore, not a reliable measure for the dynamic rate and vice versa. INTRODUCTION Filtration under simulated borehole conditions, i.e.. either from a static suspension or from a suspension flowing parallel to the filter cake (dynamic filtration), has been the subject of several laboratory studies.1-7 This experimental and theoretical work showed that many aspects of the filtration mechanism cannot be explained by an elementary filtration theory based on the assumption that the filter cake is incompressible. For a more satisfactory theory compressibility should be taken into account. This has been done. at least to some extent, in the filtration theory developed for the chemical industry. Surveying the literature (see Ref. 8 for a bibliography) it becomes apparent that, although several properties of filter cakes deposited from many different suspensions have been measured, including compressibility, the filtration equations are essentially empirical in nature. No attempt has been made, for instance, to develop filtration theory along the lines of consolidation theory.12 This theory, upon which a highly successful development in soil mechanics rests, would appear to be an excellent starting point for a filtration theory since the compressibility concept is an essential part of it. As we will use this theory in the following development it is well to state the four assumptions on which it is based: 1. The fluid flow through a compressible porous medium is governed by Darcy's law. 2. The rate of change in fluid content of an element of the porous medium is proportional to the rate of change of solid pressure between the particles. 3. The solid particles are incompressible within the range of pressures considered. 4. The total pressure on a surface normal to the line of flow is equal to the sum of the fluid pressure and the pressure between the particles (solid pressure) at that surface. To calculate the rate of filtration and other quantities of interest it is necessary to know the filter cake compressibility and the permeability as a function of the solid pressure. It has not been possible to calculate these functions from theoretical considerations and they will therefore be introduced in this paper as empirical expressions. Both are determined in a compression cell where the cake is subjected to a mechanical load. Permeability and compressibility are measured after the solid pressure has stabilized, i.e., after the excess fluid pressure has been dissipated and the uniform pressure is transmitted entirely by the solids. The permeability and compressibility thus determined are not the same as during filtration in the borehole, under either static or dynamic conditions, because then, due to frictional drag, the solid pressure and hence also the permeability and compressibility vary along a line normal to the direction of the mean flow and can only be defined locally. DERIVATION OF THE FILTRATION EQUATION FOR COMPRESSIBLE FILTER CAKES As the filter cake in the borehole is thin compared to the radius of the hole the filtration may be considered as linear. Taking the x-axis normal to the wall, with its origin at the formation, we have, according to Darcy's law,

By Frank S. McKenna, Myron A. Pugacz, Clarence E. Jackson

The notched-bar impact test has proved worth while in certain applications as a test for control of the quality or the heat-treatment of steel. In view of the serious thought that even so simple a test as the tensile test has evoked during the past years, it is not surprising that the notched-bar impact test should have inspired much experimental work. The correlation of the great number of data has not been successful, although steady progress has been made toward a better understanding of this test. Progress has been made, especially, in the isolation of the effects of the many variables that control the results. The stress system imposed on a specimen with a notch is so complicated and unpredictable that no simple evaluation of the test has been possible. Because of this uncertainty, many engineers hesitate to use the notched-bar impact test, and this attitude may well continue until a better understanding of the effects of the variables in the test are available. Without doubt, any additional data that may be presented should be accompanied by as complete a description of the - details of test as possible, so that it may be added to the general fund of information that is to serve as the basis for the theory of the notched-bar impact test. The many factors that may control the test results have been pointed out repeatedly. The importance of the effect of the type and dimensions of the specimen has been recognized. Most of the work reported by American investigators has been limited to small-size (Charpy) specimens tested as a simple beam; two types of notches (Fig. I) have been commonly used. Considerable data have also been presented by many investigators using a small specimen tested as a cantilever beam; this commonly being called the Izod test. Here, however, a shear component of stress makes the stress system even more complex than that present in the simple beam type of test, hence a critical analysis is difficult. Much work has also been reported by investigators using the tension type of specimen. A second variable that must be controlled is the testing temperature. An indication that the tests were performed at room temperature is not sufficient, since in many steels a variation of a few degrees in the actual testing temperature may be sufficient to give an entirely different range of results. Other factors, such as the composition and condition of the material being tested and the speed of test, should also be considered. Many investigators have contributed data and theoretical discussions on the problems encountered in notched-bar test-

Jan 1, 1944

By Archer Wheeler

THE copper industry in the Province of Katanga, in the Belgian Congo, which is now controlled and operated by the Union Minere du Haut Katanga, had its inception many years ago in the vision of a Scotsman, Robert Williams, now Sir Robert Williams, Baronet. He it was who personally negotiated the mineral concession with King Leopold of Belgium, sent in the prospecting parties who located most of the present mines of the company, later arranged for the Belgian participation from which the present company was formed, and has been its active mentor ever since. The idea back of his efforts was the establishment of an industry on the Congo-Zambezi divide, of sufficient importance to draw up to it the head of the Cape to Cairo Railroad, the dream of Sir Cecil Rhodes, and the consummation of which he had left as a legacy to Mr. Williams, his successor. The reports of the prospecting expeditions showed that copper in profitable quantity was there, but many difficulties lay in the way of the establishment of the infant industry. The isolated location of the mines, various tribal wars, the Boer War, and many other factors contributed to making progress very slow. However, in spite of these difficulties the railroad was finally built and a blast-furnace plant erected at Lubumbashi, near Elisabethville, the capital of the Province. Operations of this plant were started in 1911, treating high-grade oxidized ores and producing pig copper by a reducing smelting. Production has been continuous since that time and the company has grown so that at present it ranks as the largest individual copper producer in the industry. It is a fitting monument to the foresight, optimism and driving force of its founder, and the progressive policies of his Belgian colleagues. In January, 1914, the Union Miniere du Haut Katanga engaged as its consulting engineer, Archer E. Wheeler, metallurgical engineer, at that time general superintendent of the Great Falls plant of the Anaconda Copper Mining Co. Mr. Wheeler was commissioned by the Board of Directors to proceed into Katanga, and make all necessary investigations to enable him to report on a comprehensive development program, and to recommend a scheme of treatment particularly for their low grade

Jan 1, 1932

By W. R. Crane

Mining of the red iron ores of the Birmingham district has been carried on energetically during the past 60 years, and their development has created a large iron and steel manufacturing center, the only important one in the South. The district produces approximately 10 per cent. of all the iron ore of the United States (80 per cent. of the Alabama ore mined is red ore); also, 40 of the 400 blast furnaces of the country are in the district tributary to Birmingham. The rapid growth of the district has been made possible through investigations that resulted in radical changes in furnace practice, and a still greater impetus will come from the study of the low-grade, high-silica ores, as a result on which they will be made amenable to treatment by concentration. Mining practice in this district has been comparatively simple because of the occurrence of the ore; but with the rapid extension of the workings and the disturbed condition of the ore bed at some distance from the outcrop, more difficult conditions are encountered and the tendency is toward worse rather than better conditions. Should the high-silica ores of the lower bench of the Big Seam become available through beneficiation, mining practice will have to be modified to meet the new conditions, which will be rendered more difficult by the increased weight of cover that will exist at considerable distances from the outcrop. Support of workings will require greater attention and the efficient and economical operation of the mines will depend largely on the successful solution of the problems of working and handling the ore. History and EaRly Development The first explorers of the coal and mineral lands of Alabama were blacksmiths and mechanics mustered out of the army after the war of 1812. These men recognized the red rock of the Birmingham district as iron ore, and utilized it in making cooking utensils and farm implements. The first blast furnace was built and operated at Russellville in 1818, where also was a foundry and rolling mill. Soft ore was used at that time, but, in 1864, the first red hematite ore of Red Mountain was smelted, near Irondale. Birmingham was founded in 1871, and the successful use of coke in making pig iron in 1876 was the beginning of

Jan 1, 1925

Jan 1, 1922

By B. H. Caudle, A. B. Dyes

In a recent publication' it was shown that wells with a free surface in a homogeneous gravity-drainage reservoir have a hyperbolic decline with index n '. This paper reports efforts to extend this theory to practical field cases. As a first step in making the extension, a large number of lease production curves from gravity-drainage fields in the stripper stage were fitted with the general hyperbolic decline equation, q/q, = 1/(1 + y) y and n in each case being determined by statistical methods. It was found that this equation is reliable for decline curve extrapolation for periods up to at least 25 years. The resrilts obtained were disturbing in the sense that values for the index, n, were often smaller than one, which fact leads to the prediction that a well would produce all infinite amount of oil in infinite time. A theoretical investigation based on the results of the previous paper provides a suitable explanation for these low values of n. It suggests that these are obtained if production occurs from two or more layers of diflerent permeabilitv and thicktress or two lnyers having different skin effects. It is predicted that as the more permeable layers are exhausted, the index of decline, n, will rise from a value smaller than 2, to n = 2. A practical method is given for fitting the general hyperbolic decline Eq. 6 to production decline data. When this method is used, the index of decline observed in gravity-drainage reservoirs in the stripper stage when wing only data over early years 01 decline usually agrees quite closely with that determined using data over 25 years or more. This indicates that the hyperbolic decline equation is reliable for predicting behavior of such reservoirs. A method is also suggested for taking into account any changes in the value of the index INTRODUCTION As a result of both experimental work with models and theoretical deductions, it was recently concluded' that wells having a free surface in a homogeneous reservoir producing by pure gravity drainage should have a hyperbolic decline with n = 2. The present report details efforts to extend this work on ideal homogeneous reservoirs to actual field cases. It should be remembered that both the previous work and the present extension are based on the assumption that the reservoir is at very low pressure, and hence, nearly all the potential available for driving fluid to the well is the gravity head. Attempts to apply conclusions of this study to reservoirs which have considerable pressures supplementing the gravity drive may lead to difficulty. WELLS WITH NO FREE SURFACE In a dipping gravity-drainage reservoir such as that shown in Fig. 1, some of the down-dip wells have no free surface. The previous study' showed that the up-dip wells, which have a free surface, should follow Eq. 1. The following approximate analysis, of a type which was justified experimentally for up-dip wells in the work just mentioned, leads to results for the down-dip wells.

By J. H. Keeler

The tensile characteristics of Zr-Fe binary alloys containing up to 5 atomic pet Fe are reported for the temperature range —195o to 500°C. A linear relation between stress at constant strain and volume fraction ZrFe2 was found. The coincidence of data from unalloyed zirconium with zero volume fraction ZrFe2 indicated little or no solid solution in IL-zirconium, in agreement with Hayes, Roberson, and O'Brien.' The absolute increase in strength due to particle strengthening, although decreasing with increasing temperature, was a greater percentage at high temperature. ZIRCONIUM is of interest for use in nuclear reactors because of its low neutron absorption, good corrosion resistance, and high melting temperature. The alloying of zirconium with iron has been considered as a means of increasing the mechanical strength of zirconium without seriously increasing the neutron absorption " over that of unalloyed zirconium. The Zr-Fe system has a eutectic at 934°C and 23.7 atomic pet Fe and a eutectoid at 800°C and 4.0 atomic pet Fe. The zirconium-rich end of this system determined by Hayes, Roberson, and O'Brien' is shown in Fig. 1. The intermetallic phase coexisting with a and ß-zirconium has been reported as Zr2Fe3,1 with a,, - 7.04A, and as ZrFe2,2 face-centered-cubic, the phase being of the MgCu, type (C-15). It was more recently agreed to be ZrFe33 and face-centered-cubic. This intermetallic phase is essentially insoluble in a-zirconium, the hexagonal-close-packed modification; and the lack of solubility makes the system particularly interesting metallurgically. The system is strengthened almost exclusively by particles of in-termetallic phase, and there is very little solid solution strengthening to complicate the analysis. The Bureau of Mines, in its survey of zirconium-base alloys,' reported the tensile properties of Zr-Fe alloys made from chloride process zirconium, induction melted in graphite crucibles, and swaged at 850°C in iron sheaths. Additional data on these ZrFe alloys were given by Hayes, Roberson, and O'Brien.' Chubb and Muehlenkamp% have recently reported the strength of Zr-Fe alloys containing up to about 1.25 atomic pet Fe. These alloys were made from crystal bar zirconium, hot worked at 820°C, annealed at 700°C, and tested both at room temperature and at 316°C. Experimental Procedure The materials used in this investigation were high purity zirconium made by the iodide process and electrolytic iron. The composition of the zirconium as obtained by spectrographic analysis and the nominal composition of the iron are given in Table I. Alloy ingots weighing 100 g were made by are-melting under argon in water-cooled copper crucibles in a multihearth furnace."

Jan 1, 1957