Search Documents

By D J. Thobaven

Project financing challenges caused by declining commodity prices have heightened the need to improve project metrics such as minimising capital payback and maximising net present value (NPV). Khnaiguiyah Mining Company (KMC) recognised the need to improve early cash flows at their Khnaiguiyah zinc-copper project after initial studies showed the project could not provide the desired financial outcomes necessary to compete for investment dollars in the current market.A significant improvement to the project cash flow in early years was realised through simultaneous optimisation of cut-off grade, mining sequence and strategic stockpiling. This improvement was achieved by accelerating mining in the pits, stockpiling lower value material and feeding higher value material directly to the plant. The schedule required higher mining and stockpile capacities than the sequential mine plan although minimal change occurred in the definition of ore and waste as measured by tonnes and grade. The practicality of the strategic schedule was demonstrated by implementation in the production plan with excellent conformance.CITATION:Thobaven, D J, 2014. An application of simultaneous optimisation – improving the payback period of a zinc-copper open cut project, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 137–144 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By H J. J Boshoff

Mine closure planning integrated into life-of-mine (LOM) planning during the operational phase consists of many subcategories. One of these subcategories that needs to be fully integrated into the LOM planning is that of water management planning. Issues arise when mine water management infrastructure, which is required post-mine closure, is only considered closer to the end of LOM. Once the mine is closed monitoring is focused on water quality as an indicator of closure performance, hence inadequate upfront post-mining water management planning or integration into operations will result in environmental harm. The lack of considering post-mining water management is not uncommon in LOM planning. Poor mine site water management and planning are a wide reaching problem for the mining industry. Numerous active mines have been issued with environmental notices and penalties for contaminated water discharge; including issues with abandoned mines now being cared for by governments all over the world.Mitigating sources of water contamination caused by existing and closed mine sites that are leaching pollutants might be impractical, due to inaccessibility to the contaminants or final landform topography. The opportunity to consider and introduce post-closure required mine water management infrastructure is lost once the waste facilities are constructed. Mitigating contamination is made more problematic with mines located in remote areas, serviced by dedicated roads, water supply, electrical supply, etc. It is expected that these services will be decommissioned or drastically reduced, once closure is reached making remedial work much harder. Inadequate planning, to ensure access and easily maintainable water management infrastructure, could lead to erosion and contamination going unnoticed. There are numerous examples of poor mine water management practices in Africa, Asia, Australia, South and North America. In the United States more than 23 000 km of streams are affected by pollution sourced from some 50 000 abandoned or mature mine sites (DeGraff, 2007).CITATION:Boshoff, H J J, ?2014. Inadequate water management planning resulting in long-term closure liabilities, in Proceedings Life-of-Mine 2014 , pp 233–246 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By D Hunter

A production information management system (PIMS) was recently implemented at Queensland NickelÆs Yabulu Refinery. Although a strong business case was developed to justify the significant investment in PIMS some potential beneficiaries remained sceptical of the anticipated benefits. The decision to install PIMS was justified as the on-line availability of continuous production data enabled the optimisation of some crucial operations resulting in significant cost savings, improved throughput and final product quality. Furthermore the rapid access to extended historical data has allowed the cause of repeated failure of equipment to be determined. The investment is expected to pay for itself within two years and has already contributed towards significant savings. This paper focuses on some of the diverse production improvements gained and compares the anticipated benefits in the business case to those achieved. A brief outline of the phased implementation of the OSIsoft PI data historian and complementary client software at Yabulu is included, along with details of the lessons learned.

Jan 1, 2003

The nation of Fiji is located the South Pacific on the æRim of FireÆ some four hours flying time from the eastern sea board of Australia. It is a tourist destination situated on the main route from Australia to the Americas. Fiji is a developing country that has had a fewsetbacks but the country has able, happy people that are very resilient. Most importantly, the country is a safe destination for tourists and businesspeople as the local people are friendly, have good ethics, and most speak English. Fiji is a very willing nation, hungry for knowledge and advancement. The Fiji geological setting on the æRim of FireÆ, that runs from New Zealand across the Pacific through Fiji and on to Papua NewGuinea, has many large deposits of gold and copper. Fiji is an exciting destination for mineral explorers with discoveries of gold, silver, manganese, bauxite, iron and copper. Gold was first discovered in 1921 and the first two mines opened in 1935; one of which was Emperor Gold Mining Company (EGM) the other being Mt Kasi. EGM mines gold on the margin of the Tavua caldera, some 85 km north of the Nadi international airport. EGM has operated continuously for close to 70 years, producing approximately 6.9 million ounces of gold and has an underground reserve of 847 600 ounces with a total mineral resource of 12 335 600 tonnes at 10 g/t (as given in the Emperor Mines Limited Annual report 2003). The mineralisation in Fiji is very exciting and it is common to discover spectacular intersections and outcrops, which are typical for this type of epithermal narrow vein mineralisation, but be aware that the orebodies are variable and not easy to understand.

Jan 1, 2004

By L Ventura, M Almond

The Pueblo Viejo project in the Dominican Republic installed an innovative sample system on its reverse circulation (RC) drilling rig during commissioning and subsequent commencement of operations. As knowledge of the orebody increased with mining and plant production, cost pressures became apparent that raised questions concerning the continued use of RC drilling versus blasthole sampling for ore control.To justify the continued use of RC drilling for grade control, an in-depth study was undertaken to determine the quality of the sample and prove its value-add to the operation.To investigate the differences in sample quality, a complete bench trial was initiated across both ore pits to compare RC drill results with blasthole assays on a side-by-side basis. The results indicated that based on ore block comparison between RC and blasthole sampling, RC identified an additional 20 per cent of high-grade (+ 4.5 g/t Au) ounces.Previous work indicated that Au, Ag and Cu were all elevated in the drill fines at Pueblo Viejo (Goers and Almond, 2012). This previous test work did not consider the quantity of fines in an RC sample therefore new test work was undertaken to include particle size distribution analyses. This study would determine if the inclusion of fines in the sample was occurring and compare the quantity of fines in the sample against other sample systems and blasthole samples.Comparisons between RC samples and blasthole samples indicate that for the RC samples a range of 30–35 per cent of the sample passed 300 mesh as compared to blastholes where the range of the sample passing 300 mesh was 15–30 per cent.This paper includes a case study on the importance of accurate samples and how they have impacted throughput through the pressure oxidation process plant at Pueblo Viejo. The accurate samples provided by RC allow for improved stockpile and blending strategies, showing the importance of accurate samples to manage risk and create value, against the perception that savings can be made at the risk of poor sampling performance.CITATION:Almond, M and Ventura, L, 2017. Adding value with reverse circulation drilling at Pueblo Viejo, in Proceedings Tenth International Mining Geology Conference 2017, pp 277–284 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By J M. Galvin

History attests to the catastrophic consequences that fire, explosion and contaminated, noxious andirrespirable atmospheres can have for workplace health and safety in underground coal mining. It also confirms that fires and explosions present the greatest risk of partial or total loss of underground mines and equipment and that this risk continues to materialise. The design, implementation, operation and maintenance of the mine ventilation system are core controls for managing the hazards associated with these risks, both for preventing them from materialising and for mitigating their consequences if they do materialise. These are most effective when embedded in a risk management approach.

Oct 12, 2022

By T Day, I G. Robertson, G J. Lyman

"Various approaches are used in the industry for establishing procedures (sample mass estimation and method of subsampling) for sampling and analysis of gold ores. The key factors that determine the accuracy of the results that can be expected for a given set of procedures are widely misunderstood.Recent developments in sampling theory show that the estimation of the accuracy that can be expected for a given gold ore as a function of sample mass is actually a simple matter. For a given sample mass, the accuracy that will be achieved depends only on the grade of the ore and the range of masses of the grains of the gold in the ore. This, of course, demands that a reasonable estimate of the distribution or spread of gold grain masses in the ore be known. But this is something that should be known if the gold is to be efficiently recovered in the processing plant.This paper provides a simple explanation of the real facts about sampling of gold, either in the field or in the plant, and provides results for a number of cases of combinations of fine and coarse gold in an ore. The prerequisites for accurate gold sampling are:correct sampling with no loss of sample or contaminationsample preparation procedures that recognise the impact of the gold grain mass spreadpractical analysis of the sample masses required to provide acceptable accuracy.Issues of corporate governance are also discussed.Citation:Lyman, G J, Robertson, I G and Day, T, 2016. The Simple Facts about Sampling Gold Ores, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 159–172 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By T Medhurst

Recent developments in geophysical borehole log analysis using the Geophysical Strata Rating (GSR) are now routinely used in a number Australian coal mining operations. This allows development of 3D geotechnical strata characterisation models for a range of purposes. The availability of this data provides a means to identify relationships between ground conditions and ground behaviour. As a result, several new design methods have been developed to assist in the strata management process such as roof support, longwall shield design and shaft stability assessment. This paper outlines these methods and provides examples of their application. CITATION:Medhurst, T, 2018. Geotechnical strata characterisation using geophysics and its application for coal mine design, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 420–433 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By G Corder

The aim of the circular economy is to accelerate the transition from a conventional linear take-make-dispose economic model to a circular model. It is restorative and regenerative by design and aims to keep products, components and materials at their highest utility and value at all times. This extended abstract presents a brief overview of the circular economy, provides application of the circular economy in other industrial sectors including the downstream metals value chain and proposes how circular economy thinking could progress the development of complex orebodies.CITATION: Corder, G, 2018. Can the concept of the circular economy help unlock complex orebodies?, in Proceedings Complex Orebodies Conference 2018, pp 8–10 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By A Kondratiev, A E. Moiseev

Viscosity of oxide melts is one of the fundamental physicochemical properties that plays a crucial role in important technological and natural processes like slag flow, slag/metal separation, volcano eruptions etc. However, many oxides melt at extremely high temperatures and are highly corrosive in the liquid state, which makes experimental measurement of melt viscosity by traditional experimental techniques a difficult and expensive, if not unachievable, task. In this case it might be useful to employ other methods of viscosity determination such as modelling or simulation. In the present paper the shear viscosity coefficients of selected pure refractory oxides (CaO, MgO, Al2O3 and others) have been simulated at temperatures above their melting points via the classical molecular dynamics and compared to the available viscosity data (eg experimental viscosities, other model predictions) collected by the authors. The simulation has been carried out using the noncommercial molecular dynamics simulation package LAMMPS and the Born-Mayer-Huggins potential, which parameters for the selected oxides were taken from the literature. Several viscosity calculation techniques (the Stokes-Einstein and Green-Kubo equations, the so called Einstein relations, and the non-equilibrium molecular dynamics methods) have been applied to ensure a more reliable viscosity calculation. It has been demonstrated that the simulated viscosity of the selected melts agrees with the available experimental data. It has also been shown that the simulated viscosity of a number of the oxide melts investigated is close to that calculated by phenomenological viscosity models, which supports viscosity extrapolation from the corresponding binaries and ternaries, if no experimental data is present for unary systems. In general, it has been demonstrated that the molecular dynamics simulation could provide a reasonable estimation of viscosity if no other viscosity data is available.

Jun 19, 2024

By G Phillips

The Merlin project is situated 130 km south of Cloncurry in North West Queensland, Australia. It is located within the Pre-Cambrian Mt Isa Inlier and is grouped within the Eastern Fold Belt. The host rocks are metasedimentary rocks of the Proterozoic Kuridala and Staveley Formations adjacent to the Mount Dore Granite.Merlin zone represents part of the Mount Dore polymetallic deposit containing copper, zinc, silver, gold, lead, cobalt and most recently has been found to host molybdenum mineralisation. This is intimately associated with economic grades of rhenium, a naturally occurring metal that is an important component of high temperature aircraft engines. The host rock sequence is a 200 m thick zone of metasediments sandwiched between competent granite in the hanging wall and brittle quartzite in the foot wall. A distinct shear marks the contact between the granite and metasediments. The host rocks are comprised of three main rock types: black shale, phyllite and altered banded calc-silicate.Mineralisation dips to the east at approximately 45° in a package of fine grained pelites and banded calc-silicates. The top 150 m of the sequence is typified by black shale and phyllite. The lower 50 m is typified by pink banded calc-silicate. The main molybdenite zone is located at and parallel to the pelite-calc-silicate contact. Down dip, the zone splits into two or three veins hosted by the calc-silicate rock suite and haloed by thin, steep dipping, stylolitic molybdenite veinlets.The deposit was discovered in 2008 by routine infill reverse circulation sampling conducted for the Mount Dore copper deposit. One hole penetrated below the main target Cu horizon and intersected visible molybdenite. During 2009 and 2010 a 50 × 50 m diamond drill pattern delineated a total mineral resource of 6.7 Mt @ 1.3 per cent Mo, 23g/t Re, 0.3 per cent Cu (mostly Indicated Mineral Resource with minor Inferred Mineral Resource). The resource has been estimated using ordinary kriging within grade domains. Access to the deposit has commenced via a decline and production through the nearby Osborne flotation concentrator (70 km south) is expected in 2012. All facilities and resources are fully owned and operated by Ivanhoe Australia Limited, a public listed company on the Australian and Toronto stock exchanges.

Aug 22, 2011

By McLennan T, Howells E, Zastawny H, Watt J. S

Nuclear techniques have been used to determine the solids weight fraction (W) and ash content of (fine) coal in slurries independent of voidage variations. The method is based on the correlation between W and the hydrogen concentration Hsl (wt/wt) of the slurry. Hsl is determined by combining measurements of neutron moderation and ?-ray transmission. Both Wand ash content are determined by combining the above measurements with the ash-sensitive measurement of X-ray backscatter compensated by a measurement of iron K X-ray intensity.The nuclear analysis system, called the SIRO coal slurry gauge, has been proved in a six-week plant trial at the BHP Steelworks washery at Newcastle, NSW. Several probes, each containing a radioisotope source and scintillation detector, were immersed directly into the coal slurry in the feed box upstream from the bank of flotation cells. For 140 samples W, ash and voidage varied in the ranges of 0 to 13 wt percent, 26 to 41 wt per cent and 0 to 4 vol. per cent, respectively. The r.m.s. difference in solids weight fraction, determined by probe measurements and conventional assay, was 0·52 wt per cent. Ash was determined with an r.m.s. difference of 2·0 wt percent in the coal. Better sampling techniques were used in the last half of the plant trial, and r.m.s. differences were 0.35 wt per cent solids and 1·5 wt per cent ash.

Jan 1, 1986

By D Kepert, C Simpson, D Edwards

Channel iron deposits (CID) currently supply over 40 per cent of the seaborne iron ore trade out of the Hamersley Province. The two well documented producing systems (Robe and Marillana palaeochannels) were both discovered during early reconnaissance mapping principally by BHP Billiton (BHPB) and Geological Survey of Western Australia (GSWA) during the mid 1950s to early 1960s. Both crop out extensively over the majority of their length. Hot on the heels of Fortescue Metals Group 2004 - 2005 discovery of approximately 2.6 billion tonnes (Bt) of undercover iron ore mineralisation in the Chichester Range, the Fortescue Exploration Department turned its attention elsewhere throughout the Hamersley Province. Reappraisal and analysis of publicly available data and ground truthing of developing models led to the recognition of the Solomon palaeochannel system. Subsequent exploration defined a world-class Resource of some 1.9 Bt of iron ore mineralisation of which the great majority is buried CID. Apart from the Marillana CID system, the Solomon region is the only major CID with significant tonnes of sub two per cent alumina CID with over 500 Mt delineated to date. Exploration has also outlined significant supergene bedded and detrital iron ore mineralisation. Ongoing drilling is expected to increase the resource base both in terms of tonnes and confidence. This paper outlines the principal contributing factors which led to the discovery of the Solomon CID and compares its geology with the Robe and Marillana palaeochannel systems.

Jan 1, 2009

By P Hodkiewicz

Recent structural interpretations based on historic stope shapes were used to develop a rapid and innovative method to domain and simulate structurally complex, high-grade gold veins at depth in the Edna May deposit. This involved ‘implicit’ modelling of drill hole data using Leapfrog software, which allows complex wireframe domains to be built and updated rapidly, compared to ‘explicit’ manual wireframing methods that are too subjective and time consuming. Conditional simulation was used for resource estimation, in order to simulate the highly variable gold grades associated with the veins. Similar modelling methods could be used to determine the mining potential of other historic gold deposits that are receiving renewed interest because of the high gold price.Gold at Edna May is hosted in the Edna May Gneiss, which is a WNW-striking tonalitic intrusion along a shear zone that dips approximately 45° towards the NNE. Gold occurs in multiple 0.5 - 5 m thick arcuate quartz veins that plunge steeply towards the west. Two phases of historic underground mining at Edna May (1911 to 1922 and 1935 to 1947) produced 360 000 ounces of gold at an average grade 19.5 g/t from seven ‘reefs’ to a depth of 240 m. This established Edna May as one of the highest grade gold mines in Western Australia at the time.Recent drilling by Catalpa Resources confirmed the potential for down-plunge continuity of high-grade veins. New structural interpretations, based on historic level maps and wireframe re-constructions of the arcuate stope shapes, were used as ‘structural trends’ in Leapfrog to model the mineralisation. The resulting wireframes capture the complex distribution of gold in the deposit and were used as domains for resource estimation.Conditional simulation using the Turning Bands method was used to simulate the expected variability of gold grades associated with this mineralisation style and the median of the 100 realisations was used to report an inferred resource. Results of this modelling method are being used to target vein extensions at depth, to consider different underground mining scenarios, and to assess the risks associated with developing and mining this high-grade and high-nugget gold deposit.

Aug 22, 2011

Can mining promote sustainable development? What is sustainable development? Is sustainable development good for corporate sustainability? Does it work in practice? If so, is it good for business? This paper does not seek to provide definitive answers to these issues. Rather, it is presented in the interests of sharing information and contributing to the pool of collective experience. The discussion will draw on the experience of Placer Dome in Papua New Guinea (PNG). Sustainable development means development that is maintained at a steady level without exhausting natural resources or causing ecological disturbance. The term æsustainable developmentÆ is often linked to the concept of ecological equilibrium, development that is self-replenishing. While its essential meaning remains the same, in practice, and for todayÆs complex and industrial world, different people will interpret sustainable development in different ways. Given the dynamics of development and the competing social, political and economic interests, sustainable development must be seen from a much broader perspective. This is the point that this paper will attempt to make. Mining, an activity that uses non-renewable resources, can promote sustainable development. The 1987 Brundtland Report (also known as the Report of the World Commission on Environment and Development), defines sustainable development in a broader manner - as development that meets the needs of the present world without compromising the ability of future generations to meet their own needs (Elkington, 1997). This definition calls for inter-generational equity in the development and use of resources by many organisations, including multinational corporations. Corporate sustainability, on the other hand, is about developing strategies that guide a corporation to stay alive and, more importantly, to stay ahead of its competitors. It is basically about survival in a competitive social and commercial environment. In a corporate world, profitability is survival. In this context, corporate profitability, the main ingredient of corporate sustainability, is important for sustainable development. Without profits, corporations will find it difficult to practice sustainable development or indeed any development. Sustainable development can integrate mining activities with the rest of the community, add value and, in the long-term, profits to the bottom-line. Ultimately, sustainability will force corporations to adopt strategies based on a longer time scale to survive. In the mining sector, corporate sustainability depends on a close relationship with all stakeholders, particularly landowners for whom sustainable development is critically important. Increasingly, there is an acceptance of the view that success is not achieved simply through competition in price, cost and technology but, more importantly, through creating social infrastructure which support community ethics, norms and values essential for trust and partnership. Needless to say, mining companies that engage in appropriate community-based development in support of inter-generational justice recognise the true value of sustainability. This is sometimes called the æhuman sustainability approachÆ which underlines the critical significance of trust in relationships with stakeholders and continuous improvement of corporate capabilities directed towards the future (Dunphy and Griffiths, 1998). In the long-term, such development will enhance corporate public image and acceptability. In practice, both concepts can be built on the principles of economic viability, environmental quality and social justice -what, in todayÆs parlance, is increasingly becoming known as the ætriple-bottom-lineÆ approach to business (Elkington, 1997). Underpinning this approach is a process of continuing dialogue and co-operation between governments, non-government organisations (NGOs) and business.

Jan 1, 1999

By K E. Mudzanani, T A. M Msagati, D T. Maiga, T T. Phadi, M R. Letsoal, B M. Chabalala, S W. Limani

This paper addresses critical environmental, health, regulatory and scientific concerns related to gold mining activities in the specific area of Barberton, Mpumalanga, South Africa. The paper thus calls for informed decisions to be made by the authorities to safeguard both the environment and people’s health. The novelty of this study is based on its comprehensive nature of the simultaneous assessment of both cyanide and potential toxic elements (PTEs) in tailings, while taking into account their composition variability over time. By combining these aspects, it is then possible to provide a holistic understanding of the contamination risks associated with mining tailings and thus justify the need for regular monitoring and supervision to ensure compliance against regulatory limits. Additionally, this paper considered investigating the dynamic nature of tailings, which are subject to changes in their chemical composition due to exposure to weathering by various agents. In this study, the determination of weak acid dissociable (WAD) and free cyanide in tailings was performed using a validated method employing the South African Council for Mineral Technology (MINTEK) Laboratory Cynoprobe. The PTEs in tailings were determined by an inductively coupled plasma optical emission spectrometer (ICP-OES). The results revealed that the tailings contained primarily substantial amounts of PTEs, including Fe (87 566 to 37 800 mg/L), Cu (271 to 110 mg/L), Mn (2100 to 680 mg/L), Ni (400 to 390 mg/L), Zn (180 to 68 mg/L), Cr (645 to 510 mg/L), As (450 to 128 mg/L), and Pb (up to 35 mg/L). The cyanide concentrations in tailings varied between 0.20 mg/L and 0.26 mg/L for free CN (with a mean of 0.23 mg/L in water leaching), 0.23 mg/L to 0.28 mg/L for free CN (with a mean of 0.25 mg/L in alkali leaching), 0.24 mg/L to 0.35 mg/L for WAD CN (with a mean of 0.28 mg/L in water leaching), and 0.31 mg/L to 0.39 mg/L for WAD CN (with a mean of 0.35 mg/L in alkali leaching). The measured concentration of cyanide and the PTEs was compared to the minimum permissible levels enforced by the South African Department of Water and Sanitation (DWS) and the Water Research Commission (WRC) regulations that govern the disposal of hazardous constituents into the environment. Additionally, it was observed that the concentrations of contaminants in the tailings exceeded the acceptable minimum limits for hazardous waste exposure, posing risks to the environment and human health.

Apr 16, 2024

By E J. B van Etten

This paper reports on the results of several years of monitoring rehabilitation at a silica sand mine on the Swan Coastal Plain, south of Perth. Mining here occurs below the regional watertable and leaves a post-mine landscape of dredge pond voids (pit lakes) with surrounding battered slopes. The restoration we recommended was to develop the pit lakes as wetlands of regional analogue and value. Several different restoration techniques have been applied to re-vegetate pit lake slopes over many years which have enabled an evaluation of reasons for success/failure of different restoration approaches. Learning acquired clearly showed the benefits of using fresh topsoil for restoration over topsoil that has been stockpiled for several years. Most topsoil used in restoration was from seasonal wetlands and consequently restoration was most successful in the riparian zone from the edge of pit lakes to about 2 m vertically above the water table. Topsoil restored areas above this level remained poor in plant species and cover. Conversely, remedial seeding/planting proved largely unsuccessful. Permanently and seasonally flooded pit lake margins recolonised relatively quickly and successfully with native sedges and rushes. Development of rehabilitated upper slope plant communities over time was evident with loss of typical wetland species and greater growth and survivorship of upland and dampland plant species on mid to upper rehabilitated slopes. Plant communities of lower slopes showed a converse pattern of development, with a shift towards a more typical wetland composition. We believe matching topsoil to site and development of topographic profiles similar to natural wetlands of the region are the keys to optimising restoration success of sand mines with shallow water tables.

Oct 5, 2011

By R Domotor

Brisbane’s Airport Link is Australia’s largest road infrastructure project, worth a total value of A$4.8 billion. The project is using surface and underground blasting to excavate hard volcanic rock, Brisbane Tuff. This paper tells the story of the most challenging and difficult blast of the whole project: the removal of a remnant pillar of rock (approximately 2250 m3) next to a major arterial road and within 100 m of existing infrastructure including a number of heritage listed buildings, residences and privately owned sensitive receivers. The pillar consisted of a hard rock wall (Brisbane Tuff) between 2 m and 6 m thick, 15 m high and 35 m wide; with in situ precast concrete piles embedded within 1 m of the boundary of the pillar. Orica Australia Pty Limited was contracted by Thiess John Holland, to perform the work in this area, including design, modelling, drilling and loading of the explosives, as well as blast clearance and shotfiring. Access to the area was limited so all explosives and equipment, including the 20 t drill rig, had to be lifted in and out by crane. Due to the nature of the blast, with infrastructure 5 m directly in front of the 15 m high face, there was only ever going to be one chance to get this blast right. This was an extremely complex blast which required the use of a number of different types of packaged explosives, as well as special timing techniques only made possible by using electronic initiating systems. This type of blast is high risk, and is more typical of a building demolition in the urban environment. The blast was fired on the 25 September 2010, and was highly successful. The environmental results for vibration and overpressure were well under the imposed limits, and the embedded concrete piles remained undamaged.

Nov 8, 2011

By B D. Saffron

In 1983, open cut coal mining operations were suspended at the Tent Mountain coalmine, located in Alberta, Canada in an area called Crowsnest Pass. Montem Resources (‘Montem’), an Australian mining company, purchased the asset in 2016. They conducted several drilling campaigns and undertook environmental monitoring with the intent to restart operations. In 2020, Montem completed a Definitive Feasibility Study, which indicated a mine life of more than 14 years.

Aug 2, 2023

Tunnels are being built around the world using TBMs and prefabricated segments or in situ concrete as linings. Clients demand high quality of these linings to guarantee a long-term stability and density of the tunnels. This paper describes the development and the use of segmental lining systems, including joints, important design criteria, installation procedures, possible mistakes and consequences, repair works and final results for different sites in Europe and around the world. The experience on these sites shows that damages may occur, if some essential aspects are not considered. These aspects include:parameters of the TBMs and back-up equipment such as fixation of jacking rams, movement of the back-up on the lining or ring reformer;parameters of the segments such as quality of moulds, quantity of reinforcement or structure of the joints; andparameters of the tunnel drive such as advance rate, ring-gap grouting or experience of the tunnel crew.All these aspects have to be considered very carefully in detail to get a good lining accepted in total.

Jan 1, 1999