Search Documents

By D J. Bradshaw, E M. Wightman, C L. Evans, B Triffett

During the commissioning phase of Prominent Hill, periods of reduced recovery were experienced with higher-grade ore blends. This was unexpected and as part of the process to identify the cause, surveys were conducted in May 2009, with two different ore blends (copper grades: 1.94 per cent Cu (blend 1) and 2.49 per cent Cu (blend 2)). Metallurgical performance was assessed in terms of rougher recovery and grade with consideration of both pulp and froth effects. In addition, hydrodynamic measurements (gas hold up, bubble size, superficial gas velocity) as well as measurements of bubble load and top-of-froth grade were taken during the surveys and full mineralogical assessment of selected streams completed to characterise the nature of the differences. The metallurgical results showed that the lower performance was obtained with blend 2 which contained the higher amount of chalcocite and was higher-grade. Analysis of the survey data showed that for both ore blends more than half of the copper loss occurred in the +38 ¦m size fractions. Almost 30 per cent of the copper in the +38 ¦m fractions that reported to the rougher tails during processing of blend 2 was liberated compared to less than five per cent for blend 1. Additionally almost 60 per cent of the copper in the +38 ¦m fraction of blend 2 was chalcocite compared with approximately 20 per cent in blend 1. This paper discusses the sensitivity of the chalcocite-to-surface chemistry effects causing marked reductions in recovery either through reduced pulp recovery or froth phase (detachment) effects. The reagent suite and operating conditions were subsequently changed and the recoveries increased substantially and the sensitivity to ore changes eliminated. It should be noted that subsequent optimisation work, which focused on recovery improvement, has led to copper recoveries of over 90 per cent being achieved.CITATION:Bradshaw, D J, Wightman, E M, Evans, C L and Triffett, B, 2012. Characterising the reasons for the difference in performance of two ore blends in early processing at OZ Minerals Prominent Hill Operation, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 273-278 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By D Connelly

Magnetite orebodies generally means mining lower grade iron ores, crushing and grinding with significant energy costs in processing and the capital costs being significantly higher than for direct shipping ores (DSO). Overseas, the mining and processing of magnetite ores has a long history of production due to the lack of DSO deposits. This raises the question as to why the new magnetite projects have been so problematic and also whether there is a future for the long list of potential magnetite projects in Australia.The quality of the magnetite concentrate product is superior to most DSO products and the magnetite contains energy benefits when converted to hematite in sintering or pelletising. The industry’s hopes for new projects have been dashed and questions are being raised as to the financial viability of such projects.A comparison of Grange Resources Savage River, Arrium’s Project Magnet, the Sino Iron Project and Gindalbie’s Karara Iron Project is used to understand the differences between the projects and why some are more successful than others.CITATION:Connelly, D, 2015. What is the future for magnetite projects in Australia and why have some of the new projects been so problematic?, in Proceedings Iron Ore 2015, pp 107–114 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

There are many compelling reasons why correct sampling schemes should be standard practice in the mining industry, yet there are numerous examples where poor sampling practices are known to exist in the business yet permitted to continue. It is not just technical issues that can be ascribed to the reasons for the continued use of incorrect methods. This paper proposes non-technical reasons why incorrect sampling practices continue, and identifies potential ways to overcome them.

Mar 1, 2010

By R Verreet

In April 2000 Mount Isa Mines installed hoist ropes of a new design on the double-drum winder at their P49 shaft. The ropes, CASAR Duroplast, were about three times as expensive as the previously used triangular strand ropes. The P49 shaft is situated at Mount Isa MinesÆ George Fisher Mine, located some 30 km north of Mt Isa. This shaft used the tried and proven 6 x 33 triangular strand style ropes. The rope life attained by these ropes at the time was acceptable due to many years of satisfactory performance. The following study indicates the improvement of service life using CASAR Duroplast rope in P 49 shaft, which depends on shaft and winder parameters of that particular shaft and cannot necessarily be generalised to other shafts.

Jan 1, 2005

By Bearman R. A, Parkin R. M

In the comminution industry cone crushers are widely used for secondary and subsequent stages of size reduction. Traditionally cone crushers have been operated and monitored manually. Alteration of discharge setting is now commonly achieved via hydraulic means, however, compensation of liner wear can still involve plant shutdown and loss of production. Drift in discharge setting due to liner wear is still a major problem that must be addressed to improve product quality, consistency and reduce recirculating load. The continuous demand for better quality products and the high cost of reprocessing or discarding unsaleable material, highlights the need for re-examination of the technology associated with the crushers to ensure optimum control and system efficiency. A collaborative project between Pegson Ltd, one of the leading UK manufacturers of jaw and cone crushers, De Montfort University Leicester, and Transfer Technology plc was established to address the technological requirement for automation of the control of cone crushers. The machine chosen for the study is a 900 Autocone cone crusher manufactured by Pegson Ltd. The design philosophy is based on a mechatronic approach providing a complete solution through a distributed network of intelligent sensors, artificial intelligence technology and adaptive control. The modular design of the system ensures a progressive sophistication in technology that allows the automation to be phased in as required. This will ensure maximum benefits to all sectors of the aggregate industry. It is estimated that the automation will result in savings of around ten per cent. The savings will result from minimising the production of unsaleable products by reliable condition monitoring and automation of the control and maintenance of system parameters to optimise system efficiency. Extension of the methods and principles into the mining sector is anticipated. The control over the size of crusher product will offer great benefits to the mining industry with significant implications for subsequent milling and beneficiation processes.

Jan 1, 1995

By T P. Medhurst

In many cases mine design is the most important driver of the profitability of a mining project, however to reach an æoptimumÆ mine plan many compromises have to be made. Some of the fundamental profit (and loss) drivers relate to stoping methods and stope design parameters. Inevitably trade-offs have to be made between the stability of underground openings, ground support costs and production efficiency. This paper looks at the role of geomechanics in the mine planning and design process. The concepts of æcontrollable lossesÆ and æuncontrollable lossesÆ are developed as a means of partitioning ground control costs. A stope design example is given which provides a method of examining mining costs, and includes a decision making element in order to quantify geotechnical impacts and select stope dimensions. The method also provides a general framework as a means of balancing ground control costs against maximising returns from an underground mining project.

Jan 1, 2000

Supergene nickel sulphide ore mined currently by Agnew Mining Company is at times partially oxidised to sulphate. The resulting soluble nickel, and calcium and magnesium in mill water, are shown to act as depressants in flotation. The depressant effect is favourably selective in that violarite, the main nickel mineral, is less affected than pyrrhotite. Nickel recovery, however, is adversely affected, probably through reduced flotation of complex sulphides. Soda ash consumption is increased markedly by the presence of the cations as shown by operating data and pulp titration tests. A significant increase in concentrate grade, from 9% to 14% Ni, was achieved late in 1981. One of the changes in plant practice which contributed to this improvement was the addition of soda ash to mill feed rather than to flotation feed as before. It is shown by laboratory tests that this reduced the depressant effects of the cations, thereby improving recovery at the expense of rougher selectivity, or equivalently, increasing concentrate grade at constant recovery. The selective depressant effect cannot be exploited until scavenger recovery is improved and a scavenger concentrate regrind-retreat äcircuit is implemented. Development is

Jan 1, 1978

By B Cook, M Karakus, J Light, E K. Chanda

The aim of this research is to develop a model through which the appropriate paste recipe parameters, for example solid content and cement content, can be derived given the stope specific requirements such as stope dimensions, required strength and curing time. A large number of samples and uniaxial compressive strength (UCS) tests were conducted at the Angas Zinc Mine (AZM) paste plant and testing facility. Samples were varied in tailings solids content, cement content and sand content. The results of this testing were modelled to determine the UCS relationship to each of the parameters. The output of this modelling was an easy-to-use program that outputs the design mixture given the stope dimensions and required stope backfill-curing time. This allowed flexibility within the mining schedule for curing times of cemented paste backfill stopes. The optimised schedule using the stope specific mix design, when compared to the standard 14-day curing time used previously, resulted in a smoother weekly mine production schedule. For the modelled 12-week period (one quarter) the 14-day curing time would result in an eight-day shutdown of the mill. The cost for each shutdown is in the order of $125 000/d. Due to the unique nature of each mine’s tailings, this exact outcome would not be directly applicable to another paste fill site. However, the process in this report could be followed for another site to achieve a system similar to the output of this project. This would ultimately lead to a more optimised backfill and stoping cycle and a more optimised mine.CITATION:Chanda, E K, Karakus, M, Light, J, Cook, B and Harris, A, 2014. Optimisation of the paste fill cycle at Angas Zinc Mine, Strathalbyn, South Australia, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 259–264 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By P Crittenden

Thiess Pty LtdÆs Australian Mining business unit used 7.6 PJ of energy in the 2007/2008 financial year. This represented more than 85 per cent of Thiess Pty LtdÆs total energy use and therefore meant that the Australian Mining business unit is required to conduct energy efficiency assessments and report publicly on the outcomes by December 2008 under the Federal GovernmentÆs Energy Efficiency Opportunities (EEO) Act. Thiess Pty Ltd has a policy commitment to sustainable development throughout its operations. This includes minimisation of its carbon footprint and the Australian Mining business unit has a strong focus on efficiency in all of its operations. It approached the energy efficiency assessment as an opportunity to further improve and build on its energy efficiency and greenhouse gas reduction focus in the business. As a mine contractor, Thiess faced a number of challenges in designing an assessment process that would be both effective and efficient to deliver. For example, unlike most other companies involved in the Energy Efficiency Opportunities program, the energy use associated with the Australian Mining business unit is not fixed to any single geographic location in Australia. Mining vehicles are moved from site to site according to the specific requirements of mine owners and the timing associated with the commencement and completion of contracts. Thiess departed from a traditional æsite by siteÆ based assessment and designed a ærepresentative assessmentÆ approach that involved detailed investigation of data across all sites and a focused assessment on a single site.Data and analysis was an essential part of the assessment and indicators at company, mine and site level were essential in identifying opportunities and tracking progress. Forty-six potential energy saving opportunities were identified and four of these are currently being implemented. The projects being implemented are: payload management, automating mobile lighting equipment, plant idle time management, and turbo idle downtime. The potential savings from the four major projects that have been identified are approximately 150 800 GJ/annum, equivalent to 10 600 tonnes of CO2-e/annum with a simple payback period of less than two years. Beyond the fuel savings however, there are a number of other benefits from the assessment, including operational efficiency, reduced maintenance costs and even a potential reduction in the number of vehicles required to complete the work. The EEO assessment has significantly increased the importance and urgency of energy efficiency and facilitated the sharing of good practice across all Thiess operations. Not only have four projects been adopted for immediate implementation but a further pipeline of projects is available for future possible implementation. This case study describes: how Thiess conducted its assessment including the use of energy data and indicators, the opportunities identified that are currently being implemented, and the lessons learnt and how other organisations can use these to improve their approach to energy efficiency assessments. This case study is a more comprehensive version of a case study developed for the Commonwealth Department of Resources, Energy and Tourism. The assessment results reported in this case study are drawn from the Thiess Energy Efficiency Opportunities Report 2008.

Jan 1, 2009

By Eggleton R. A, Taylor G

As the search for major orebodies continues, the regolith dominated areas of the Broken Hill region remain one of the major exploration frontiers. The past exploration philosophies emphasising bedrock related characteristics have been limited in their ability to effectively explore in the regolith dominated areas, that are a feature of most of the Broken Hill region (Figure 1). If mineral exploration is to be more effective across all of the Broken Hill region, particularly in the regolith dominated areas, an appreciation and increased understanding of the regolith and landscape features are a necessity. Ironically, there have been very few studies of the regional regolith and landscape features of this region. Owing to the previous lack of an established regolith-landform framework, this study initially concentrated on the general characterisation and variation in regolith types corresponding to the area of the Broken Hill Block, within NSW (Willis, 1989; Stevens, 1986). The approach has been to produce a regional regolith-landform map at 1:100 000 scale and conduct a complimentary program of regolith sampling and site descriptions. This was a basis to identify areas for more detailed regolith-landform mapping (1:25 000 scale) and for producing a regional stratigraphic framework and models for landscape and regolith evolution. This information can then be used to provide a basis for regional mineral exploration models and strategies. This paper highlights some of the regionally significant regolith-landform features and their general significance to mineral exploration. More detailed information on specific regolith-landform features and study sites may be found in Hill et al (1994; 1996; in press) and Hill (in prep).

Jan 1, 1997

By S Kost, R Nievergelt, F Cortes

In recent years, the use of steel fibre-reinforced concrete (SFRC) for segmental tunnel linings has become increasingly popular due to numerous advantages including durability, resistance to spalling, reduced cracking at corners and edges and significant cost-saving potential. One of the key parameters for measuring the performance of SFRC is the residual (post crack) flexural strength. A problem often faced in design and quality control of SFRC is the high variability of results obtained by standard beam test methods, with reported coefficients of variability (CoV) in the order of 25 per cent. The high test variability results in a relatively low permissible design strength relative to the average flexural strength of the material and commonly leads to non-conformances with respect to residual flexural strength during production testing.This paper presents the implementation of an alternative testing method using large round determinate panels (RDPs) for quality control testing of the SFRC used in the segmental lining of the City East Cable Tunnel (CECT) in Sydney. The alternative RDP test method was found to correlate well with standard beam tests and significantly reduce the variability of test results, minimising the risk of outlying residual flexural strength results, with zero non-compliant test results reported during the production period.This successful implementation of an alternative test for post-crack flexural strength with lower variability in results constitutes a relevant precedent to demonstrate the feasibility of this approach which contributes to the development of more cost-effective concrete mixes and minimises the risk for non-compliant results and the contractual disputes that commonly arise from these.CITATION:Cortes, F, Nievergelt, R and Kost, S, 2014. Development of a segmental lining specification for steel fibre reinforced concrete flexural strength testing using round panel tests, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 461–468 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

The metals titanium and zirconium and their alloys occupy individually unique positions in the catalogue of metallic materials available for engineering applications. Because of the uniqueness of their usage in the aerospace industry, in the case of titanium, and in the nuclear industry, in the case of zirconium, the except- ional resistance of both the metals to the majority of corrosive media is often overlooked. The cost factor in the application of these more exotic metals has, in the past, been a major considerat- ion in the rejection of titanium and zirconium as constructional materials in areas of usage where their superior corrosion resistance strongly favoured them over more conventional metals and alloys. The cost differential, vis-a-vis austenitic stainless steels, for example, is not a trifling matter, being of the order of 6 : 1, when compared on a weight basis. However, if one considers the cost, for, say, sheet product on an area basis, the ratio is redgced to approximately 3.4:1. If one also takes into account the enhanced performance of the more expensive material and the sub- sequent increase in service life and decrease in plant down-time, the economics of the usage of materials such as titanium becomes much more attractive and, indeed, highly competitive,

Jan 1, 1969

By H Dehghan Jan Abadi, K Shahriar

The iron ore district of Gol-e-Gohar (GEG) is located 60 km south-west of the city of Sirjan, in the Kerman Province of the Islamic Republic of Iran. Six exploration targets have been identified and iron ore has been mined from one area with dry and wet concentrate products sold. Prior to mining commencing in 1999, the proven reserves were estimated at 265 million tonnes (Mt) in 2004 and 40 Mt of 100 Mt overburden has since been mined. Of the six exploration targets, the largest anomaly in the GEG district is Deposit No 3. This paper discusses economic considerations focusing on mine extraction and construction of a concentration and pelletising plant to process ore from Deposit No 3 of GEG. Planned capacity of 10 Mt product (concentrate and pellet) per year is targeted to commence in 2011, and nominal capacity by 2014. The economical evaluation and analysis is one of the most important stages in the feasibility study of mine development. Financial calculations including the provision of financial resources, operation period revenue, loss and profit statement, cash flow, net cash flow, internal rate of return and net present value have been undertaken as part of the feasibility study. The feasibility study operating plan assumes a large open pit mine containing proven reserves of approximately 250 Mt. The feasibility study assumed an economic return of $80 per tonne iron pellet. The economic study determined that Deposit No 3 of GEG can be economically developed by open pit mining followed by magnetite separation and flotation to generate iron concentrate and pellets.

Jan 1, 2007

By C Vejrazka1

The occurrence of airblasts is one of the principal mining hazards in caving operations between the time of cave establishment and breakthrough of the cave to surface. As such, it needs to be managed continuously and risk assessments need to be reviewed on a regular basis for applicability to changing conditions. The likelihood of an airblast occurring is based on a range of geotechnical factors over some of which engineers on-site only have limited control. However, the impact of an airblast to the underground mine, if it does occur, can be managed by following established safety guidelines for the production from the cave.This paper outlines how the Caving Airblast Simulation Tool in Ventsim was used to determine a risk management strategy for a sublevel and a block cave at a mining operation in Australia. The block cave has a footprint of 14 500 m2 with the extraction level located 1250 m below surface while the sublevel cave currently has a footprint of around 18 000 m2 operating between 660 m and 800 m below surface. Both caves are currently in their early operational periods. The risk analysis provided valuable information for the production planning of the caves including confirmation of extraction ratios for the block cave undercut, locations of airblast walls and maximum allowable air gaps for different muck pile heights to ensure safe operation is achieved.

Oct 12, 2022

By K J. Lownie, T Rafferty

The in situ testing of mine ventilation fan systems has been a contentious issue for many years. Site testing was generally undertaken by adapting standards that were developed for the laboratory testing of fans using standardised airways. The deficiencies inherent in this practice have been widely recognised by informed practitioners, and this led to the first stand-alone document specifically intended for the in situ testing of large fans (ISO 5802:2001 Industrial fans - Performance testing in situ).This paper describes the structure of the International Standards organisation and the processes that are followed in the course of preparing such a standard.The application of ISO 5802:2001 is briefly outlined together with how test data is assessed for compliance with the suppliers guarantee. This paper must be read in conjunction with ISO 5801:2007, ISO 5802:2001 and ISO 13348:2007.CITATION:Lownie, K J and Rafferty, T, 2013. A review of ISO 5802:2001 industrial fans - performance testing i n situ, in Proceedings The Australian Mine Ventilation Conference , pp 149-154 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

This paper discusses the requirements for a successful simulation modelling study, and the steps involved in the modelling process. Advantages and disadvantages of simulation are described, and a case study highlights how not to go about it. Two other case studies, for a decline truck haulage and a block caving production operation, are used to illustrate the types of variables whose impact may be investigated. Typical results are presented to indicate the sorts of presentation styles the author has found useful for conveying study results to project sponsors. Standard spreadsheet charting techniques can be very useful in this respect, but the possibilities are limited only by the imagination of the study team.

Jan 1, 2000

By A Querzoli, B Williams

In late 2014 the Flinders Power Management Team was executing business improvement plans to ensure continued electricity generation until 2028 and beyond. Six months later, in June 2015, the Board announced the closure of the Flinders Power South Australian business, including the Leigh Creek Coal Mine, the Northern and Playford Power Stations located at Port Augusta and the 250km railway line. The announcement was preceded by a brief period of internal planning. A date was soon set for ceasing coal mining operations, being November 2015. The mine is unique in many ways. Located approximately 550km north of Adelaide the site has over 100 years of history and was formerly operated by the South Australian Government. Privatisation in 2000 saw the mine continue operation under Perpetual Leases from the South Australian Government. The leases included exemptions from multiple sections of the Mining Act 1971, obliging primary regulation under the Mines and Works Inspection Act 1920. The coal, being a low rank sub-bituminous brown coal, is prone to self-heating and spontaneous combustion. The mine and company town Leigh Creek were the economic and cultural heartbeat of the community. Facilities at the mine were shared by the community and vice versa. While many mines across Australia and the world enter periods of care and maintenance, few have been actively closed to the point of relinquishment (Bennett and Lacy, 2016). A swift decision to close, followed by a short mining operations shutdown period, presented significant technical and regulatory challenges for both the mine operator and for Regulators. The subsequent joint risk mapping process employed by Flinders Power and South Australian Mining Regulators was a unique real-world example of collaborative mine closure planning and execution. Lessons learnt are valuable for all mines, production facilities and for Regulators, even for those who may wrongly assume that closure is many years away. CITATION:Williams, B and Querzoli, A, 2018. Risk management for minesite closure planning and execution – start now! Lessons from the closure of the Leigh Creek Coalfield, South Australia, in Proceedings Life-of-Mine 2018, pp 68–72 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By I Canbulat, J Emery, L Yao and C Zhang

This paper documents a process of data analytics and machine learning applied to coalmine roof convergence data. It follows a publication documenting the formation of the database. For each set of analyses Python scripts were utilised to extract data from an SQL database, with subsequent analyses also executed in Python, utilising open-source tools such as scikit-learn. Preliminary analyses with classic machine learning algorithms included multiple logistic regression, K-nearest neighbours, decision tree, random forest, support vector machine, kernel support vector machine, artificial neural network (ANN), naïve Bayes and multiple linear regression. Results indicated that relationships were complex and non-linear, with the artificial neural network most suitable. An ANN model was then refined through a standard process of hyperparameter optimisation and data augmentation to arrive at a final model. Due to the black box nature of the ANN further insight into how the parameters interacted was sought and found with Shapley additive explanations (SHAP values). SHAP values utilise Game Theory, where each input parameter or feature is a ‘player’ while the data set is the ‘team’. The SHAP value is the impact of each player on the target value, essentially establishing the contribution of each input parameter. The results from all analyses are delivered in the paper, together with insights, applications, strengths, and limitations of the methodology.

Nov 29, 2022

GENTLEMEN, I have to thank you very much for the honour you have conferred upon me by electing me President of the Institute for this year. On behalf of resident members, I have to offer the visitors a very cordial welcome to Mount Morgan, and to tell them that all arrangements have been made to enable them to inspect the mine and works at their own convenience, and to supply them with any particulars they may need.It is very pleasing indeed to see such a large gathering, especially on account of the long journeys many have undertaken in order to be present. The first congress in Queensland, about eleven years ago, was attended by a comparatively small number of members, and a rather long time has been allowed to pass in consequence. The large attendance at this meeting encourages the holding of meetings in Queensland more frequently. Owing to the long distances, and the number of mining centres in Australia and New Zealand, we cannot expect to meet oftener than once in six or seven years in...

Jan 1, 1911

By Q Qu

Reliable prediction of longwall gas emission sources and rate plays a critical role in mine ventilation and methane drainage capacity planning. Over the years, Australian longwall mines have been using the historic Winter method and the Flugge method in modelling specific gas emissions (SGE). The predicted results often experience high discrepancies from the operational reality. To improve gas emission prediction, post-mining gas contents were measured in several mines in Qld and NSW by safely drilling core holes into the longwall goaf. The results revealed many new insights into gas emission characteristics from different coal seams and the drawbacks of the European methods in their use in high-production gassy Australian longwall mines. Based on measurement data, a new, time-dependent gas emission prediction model has been developed. Considering several factors such as caving, desorption and production rate, the new model can predict more accurate and meaningful gas emissions to meet today’s needs in mine gas emission management. A case study is provided to demonstrate the application of the new SGE model.

Oct 12, 2022