Search Documents

By C Lower

An unprecedented, quantitative, deposit-scale understanding of major clay mineral distribution throughout the Yeelirrie uranium deposit has been achieved by adapting the existing HyLogger™/HyChips™ analytical technique to measure resource assay pulps. Spectral analysis via HyLogger™ and HyChips™ systems has previously been used as a small-scale geometallurgical research tool, but never before has it been quantitatively applied to an entire resource sample population for the purpose of developing stand alone block models for major clay minerals. Economic uranium mineralisation within the thin but extensive Yeelirrie?palaeochannel?primarily exists within the transition zone between a groundwater-derived calcrete and the underlying clay-quartz regolith. Early geometallurgical investigations identified that certain clay minerals could be deleterious to the efficiency of the uranium recovery process. Accurate calculation of clay mineralogy from resource assays proved too difficult due to chemical similarities between co-existing kaolinite, smectite and magnesium carbonate minerals. A relatively low-cost, efficient and accurate method of quantitative clay mineral analysis was required to measure over 70 000 resource assay pulps. After initial testing and comparison with QXRD, the HyChips™ 3-1 spectral logging system was implemented as a primary method of clay mineral analysis for the Yeelirrie uranium deposit. The resultant spatial data set allowed the interpretation and geostatistical analysis of geometallurgical domains across the deposit. Clay block models were generated and used in geometallurgical resource calculations to benefit the mine planning process.

Sep 5, 2011

By Connell JE

The Worthing Mine near Hallett Cove. 20 km southwest of the cite of Adelaide, belongs to Aus- tralia's first mining era, which took place in South Australia between 1841 and 1851 (Figure 1). Oper- ations began in 1849 only six years after the com- mencement of metal mining in Australia at Glen Osmond. Although not as historically significant as Glen Osmond (1841), or the much larger copper mines of Kapunda (1844) or Burra (1845) its importance lies with its Cornish enginehouse and chimney. The Worthing enginehouse, built in 1851-1852 is the oldest remaining in Australia and certainly the most significant relic of Australia's first mining era. Six other stone enginehouses were built during that period: at Kapunda in 1848 and 1850: at Burra in 1849, 1850 and 1851; and at Tungkillo in 1849. All of these houses have long since dis- appeared although the foundations of one (Kapunda, 1850) still remain. The significance of the Worthing site is enhanced by its magnificant environmental setting in the bare, steep valley of Field River. Currently (1986) the Worthing Mine is the only site within the City of Marion which is on the Register of State Heritage Items. The site is also included in the Classified List of the National Trust of South Australia and on the Register of the National Estate.

Jan 1, 1987

By Taylor GP

Mining Lease SML 57 was registered to Mount Kasi on 5 January, 1995. The Mount Kasi gold mine is located in Vanua Levu, Fiji's second largest island and operated from 1932 to 1946 producing 261,000t of ore at an average grade of 7.5g/t Au. The deposit represents a structurally controlled style of high sulphidation copper gold mineralisation with peripheral low sulphidation mesothermal vein type gold mineralisation. The resource consists of 1,048,000 tonnes of residual soils (eluvium) containing 1.9 g/t Au at 0.5 g/t Au cut off and 1,240,000 tonnes of hard rock at 3.0 g/t Au and 1.0 g/t Au cut. 94 drill holes, 298 auger holes and 85 pits were modelled to outline the resource. 29% of the pits bottomed in mineralisation and it is likely the full thickness of eluvium has been understated. The pit is scheduled to produce 500,000 tonnes of ore per annum to yield 35,000 ounces of gold with an initial 2 years of eluvial ore followed by a further 2 years of hard rock ore. Total capital costs are estimated to be less than 10.0 million dollars with construction planned to commence in 1995. The likelihood of locating further ore is high.

Jan 1, 1995

By Thomson I. R R, Friday R. G, Palmer W. T

The paper introduces the problems encountered in designing open stopes and briefly examines the factors that determine the final stope dimensions achieved after mining is completed. A case study is presented where monitoring of a stope was considered necessary due to the expected formation of a highly stressed crown pillar above the stope. The influence, on the mining approach adopted, of a yielding crown pillar is discussed. Monitoring and numerical modelling were used to develop an understanding of the behaviour of the particular stope as mining progressed. A comparison between the measured displacements and the numerical predictions at an interim stage of mining was carried out to assist in choosing the final sequences involved in completing the stope.

Jan 1, 1981

In high stress mining environments, production drill rigs are often employed for rapid drilling of boreholes for systematic cable bolting. One outcome of this drilling method is the need for larger boreholes than would normally be drilled using customised bolting machines, such as the Tamrock Cabolter. Past laboratory studies indicate that, under ideal grouting conditions, borehole diameter has little effect on the pull-out strength of cable bolts with high bulb densities. However, the sensitivity of pull-out strength to large boreholes and less ideal variations of grout strength have not been investigated. To explore these sensitivities, industry standard single embedment tests were conducted on large boreholes simulated using steel pipes. Four borehole diameters were tested, namely: 42 mm, 52 mm, 81 mm and 106 mm. In each case the grout water to cement ratio was varied from 0.35 to 0.45 and two cable bolt bulb spacings were considered, namely: one and three bulbs per metre. The results indicate that, across the range of parameters tested, variations in peak axial load at failure corresponding to changes in hole diameter were statistically insignificant.

Nov 25, 2010

By Bhattacharyya A. K

A major constraint on sustaining high rates of production in the collieries of the Southern Coalfield of New South Wales is the inability to develop panels fast enough to match the rates of extraction. This inability is particularly crippling in the case of retreat longwall mining and is due to nearly half the time in roadway drivage being spent on strata control operations such as roof support.Increased rates of roadway drivage and significantly improved roadway stability can be achieved by the application of yield pillars between parallel roadways. These pillars are designed to yield immediately upon formation and transfer the damaging roof loads away from the immediate vicinity of the roadways. Since the width of the yield pillar is the key to their successful application, it was determined through the Yield Pillar Experiment conducted by Kembla Coal and Coke Pty Ltd at West Cliff Colliery.Three experimental headings, each nominally 5.5 m wide and 2.8 m high, were driven to form two tapering pillars. The width of these pillars progressively decreased from 24 m to 3 m over a length of 154 m. The convergence between the roof and floor of the headings measured at various cross-sections corresponding to predetermined widths of the pillars are analysed in this paper to evaluate the stability of the tapering pillars at the different widths.The width of the yield pillar in a three heading development layout at West Cliff Colliery was determined to be 7.5 m.

Jan 1, 1995

By Abishev D. N, Balakirev V. F, Davydov G. I

The problem of recovery of cobalt products from poorly oxidised nickel ores (Kempirsaisk deposit) and pyrite concentrates with a low content of cobalt (Sokolovsk-Sarbaisky deposit) has not been solved to the present time in Kazakstan. The balance reserves of nickel ore of the Kempirsaisky deposit make up more than 35 million tons with a nickel content of 1.13 per cent and cobalt content of 0.05 per cent; besides there are 110 millions tons of out-balance ores (Anon, 1995). In a tailing dump of Sokolovsk-Sarbaisk Mining and Productional Association more than 320 million tons of tailings of wet magnetic separation have accumulated, which contain 7.2 per cent of sulphur, 0.022 per cent of cobalt, 0.012 per cent of nickel, 0.094 per cent of copper, 0.079 per cent of zinc, 16.45 per cent of iron, and from which a high quality pyrite concentrate car) he separated through flotation, containing 48 - 50 per cent of sulphur, 44.15 per cent of iron, 0.141 per cent of cobalt, 0.07 per cent of nickel, and 0.10 per cent of copper. The well-known technological flow charts for cobalt and nickel recovery from the tailings of sulphide-magnetite ores dressing (to give pyrite concentrate) and from oxidised nickel ores, are not profitable at the existing prices for metals, but are not worthless and require significant capital investments for the realisation of their value. The flow chart `sulphate roasting - leaching - solution processing' is used widely for combined processing of cobalt-containing pyrite ores and concentrates.

Jan 1, 1996

By C Zschiesche, alam, A Abadias Llamas, A K

An integrated experimental and thermodynamic modelling study of the phase equilibria in the FeOFeO1.5- SbO1.5-SiO2 system in equilibrium with liquid Sb and Sb-Ag metal has been undertaken to develop thermodynamic model of the Na-Si-Fe-O slag system with S-Sn-Sb-Pb-As minor elements based on the experimental investigation of the selected sub-systems. New experimental phase equilibria data at 575–1600°C were obtained for this system using high-temperature equilibration of synthetic mixtures with predetermined compositions in sealed silica ampoules, Fe3O4 basket in sealed silica ampoule, or Re foils, a rapid quenching technique, and electron probe X-ray microanalysis of the equilibrated phase compositions. Experimental results on phase equilibria in the Fe-Sb-Si-O+Sb metal system obtained helped to produce initial set of model parameters in the slag. The primary phase fields of quartz/tridymite/cristobalite (SiO2), 2 high-SiO2 immiscible liquids, olivine (Fe2SiO4), wustite (FeO1+x), spinel (Fe3O4), schafarzikite (FeSb2O4) and valentinite/ senarmontite (Sb2O3) were identified in the binary Sb2O3-FeO, Sb2O3-SiO2 and ternary FeO-Sb2O3- SiO2 systems. Further refinement, particularly the distribution of excess Gibbs energy among the ‘FeO’-Sb2O3-SiO2 and ‘FeO1.5’-Sb2O3-SiO2 interactions, required the study at more oxidising conditions. Oxygen potential was increased using an inert metal (Ag) rather than using the gas flow due to the high volatility of Sb-containing gaseous species. Liquid Ag-Sb alloys with low concentrations of Sb of a few percent were used. At these conditions, the concentration of AgO0.5 in slag was below 1 mol per cent, which had a small effect on observed phase equilibria in the system. In addition, important information on the solubility of silver in slags is produced, which can be valuable when treating electronic recycling materials or primary silver-containing ores through the Pb process. Two main areas were addressed: the spinel-tridymite boundary (40–70 per cent SiO2 in slag) and spinel liquidus near 15 per cent SiO2 in slag. This allowed to deconvolute the separate contributions of the FeO-Sb2O3(-SiO2) and Fe2O3-Sb2O3(-SiO2) systems.

Jun 17, 2024

By T Sua, B Wright

"BHP Billiton West Australian Iron Ore (WAIO) conducts an extensive geometallurgy program for its iron ore deposits in the Pilbara with the focus on determining the lump yield (the mass percentage of >6.3 mm rocks) and the lump and fines grade for iron ore products. The geometallurgy program provides accurate information to design engineers and technical marketing teams on the performance of different iron ore mineralogies for future deposits. Additionally geometallurgy results are being used to guide short-term production planning with their introduction into short-term geology models and grade control models. The data that underpins this knowledge is from dedicated geometallurgical programs, drilled using PQ (~83 mm) holes. These holes are crushed by intervals that are based on geological definition which provides an indicative lump yield and lump and fines grade. The lump is then subjected to standard dropping and tumbling test stages to produce a simulated lump and fines product. In the past, quality assurance, quality control holes were drilled using HQ (~64 mm) holes for geochemistry purposes. These holes were crushed to provide an indicative lump yield and lump and fines grade and then 100 per cent is sent for assay (with no dropping and tumbling). Utilising data from HQ holes can significantly increase the indicative geometallurgical data available. This paper compares the geometallurgical results from both PQ and HQ holes from a range of bedded iron deposits (Brockman and Marra Mamba). The PQ and HQ data are compared by orebody, stratigraphy and depth to exclude factors that are expected to influence geometallurgical results.CITATION:Wright, B, Sua, T, Robertson, B and Van Dijken, B, 2016. Comparison of Diamond Drill Size on Iron Ore Geometallurgical Results, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 161–166 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By S Mundell, A Atkins, S van de Water

Geoscientific information management enables the capture, management and delivery of the original geoscientific observations and measurements of the earth’s natural resources. However, original observations and measurements are worth nothing if the quality and integrity of the data can’t be guaranteed. Geoscientific information is one of the fundamental assets enabling miners to make confident and accurate business decisions, whether that is defining a resource model, performing reconciliation, delivering ore reserve reports or meeting environmental compliance requirements. Without access to reliable, validated or verified data it increases the risk of miners using incorrect information for reporting and compliance. Industry codes, such as JORC, or government regulations, such as environmental compliance requirements, must be adhered to and companies should be able to confidently report to these standards. Without having a robust information management framework in place, it becomes a challenge to make trustworthy decisions, report confidently and reduce the risk of non-compliance. As a key initiative, good data governance should form one part of a miner’s information management strategy. Within the mining industry it is common for companies to only consider technology tools as the key focus for compliance whereas a mature information management focus will additionally consider people and process. All three pillars are critical for a miner to have confidence in their data driven decisions. This paper discusses an industry framework for best-practice geoscientific information management based on the observations gathered from analysing data management practices within the mining industry. It focuses on how the three pillars of people, process and technology are crucial elements to improve operational decisions and ensure companies are compliant.

Nov 8, 2021

By D J. Williams, C Zhang, F E. Herrera Cabrera

Farming on bauxite residue using screw propelled equipment (SPE) has been commonly practised to accelerate dewatering and as it promotes consolidation and enhances storage capacity. However, it is unclear when and how often farming should be conducted during the transition of bauxite residue from slurry to dry solids and how deep each slurry deposition should be. To address this issue, three desiccation tanks were established in the laboratory to investigate how much farming could enhance the desiccation and consolidation of tailings. The cuboid tanks, of 350 mm in height and 300 mm in width and length and with an opening on the top, were placed on load cells to monitor the water loss during desiccation and were instrumented with moisture and suction sensors designed and developed at the University of Queensland to measure the water content profile of the residue. The bauxite residue, composed of silt-size particles with low plasticity, was hydraulically deposited in the tanks as a slurry at 27% solid content, resulting in 100 mm depth of solid material settling. Evaporation was enhanced by placing two identical electrical fans above the tanks. Two phases were conducted. In the first phase, the two tanks were left untouched for evaluating non farmed conditions and for calibrating sensors, while in the second phase, three tanks were subjected to atemporal farming using purpose-built screw propelled equipment. The experiment was terminated when the residue was completely desiccated. This paper reports on the instrumented tank set-up and the results obtained to date.

Jul 1, 2021

By D Maldonado

BlueScope Steel’s Port Kembla sinter machine underwent a major upgrade during mid-2009. The mixing and rolling drum (MRD) was thoroughly cleaned during the upgrade. Space factor measurements taken in October 2009 showed that the drum was operating in the cataract regime in the dry mixing section and the cascading regime in the rolling section, which is optimal for granulation. Sampling carried out during an entry into the MRD showed that both the Sauter mean diameter and the predicted bed voidage increase rapidly during wetting, and then decrease in the wet mixing section. In the rolling section, the granule properties remained constant untilthe drum discharge. Frozen particle analysis, using liquid nitrogen as the quenching agent, were carried out on material collected from the MRD discharge. The results, expressed as a Granulation Index, showed there had been a significant improvement in the granulating performance of the MRD following the upgrade. The plant studies were also complemented with laboratory scale experiments which aimed to optimise the granulation process. The effect of burnt lime on green feed permeability was quantifi ed using the laboratory scale drum at different moisture contents. A significant increase in permeability was apparent once the burnt lime dosing rates doubled from 1.1 - 2.2 per cent w/w (feed basis). The capacity of the burnt lime system at the sinter machine will be increased in order to benefi t from the expected higher permeability, permeability, which will enable the machine to sinter at deeper bed heights.

Jul 11, 2011

By D Hatton, S Wilson, F Orrante, M Taghimohammadi, F van der Walt, N Arslan, M Westcott

"Cayeli Bakir Isletmeleri is an underground copper-zinc mine in turkey. The ore is highly variable with feed grades ranging from 1–4 per cent copper and 1–10 per cent zinc. Due to this variability, ore characterisation and blending strategies are crucial for performance optimisation.This paper presents a case study for a multidisciplinary approach to process optimisation, integrating Geometallurgical and advanced control methods to achieve optimised plant performance. The results from comprehensive metallurgical tests and surveys were used to develop a mathematical model utilising SGS’s Integrated Geometallurgical Simulator® (version number 2.5.24.0). The model was employed to determine the most appropriate operational settings required to ensure that optimised grades and recoveries are achieved for each ore type.SGS’s Modular Expert Technology (MET) expert system was then implemented to target these optimum operational ranges utilising online grade and froth velocity measurements. The successful conversion and deployment of the modelled process parameters into an expert system has resulted in significant improvements in overall recovery and circuit stability.Citation:Arslan, N, Westcott, M, van der Walt, F, Hatton, D, Taghimohammadi, M, Orrante, F and Wilson, S, 2016. A Multidisciplinary Approach to the Optimisation and Control of a Copper-zinc Grinding and Flotation Circuit, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 115–122 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By M Haest, S Sandler, R Botha, H Lang, K Hume

Benchmark practices in the mining industry include the establishment of Quality Programs — Quality Assurance and Quality Control (QAQC) — to monitor the correct execution of sampling protocols and control each stage of the ‘Sample Cycle’: Sample Collection, Preparation (comminution) and Analysis. QAQC reports commonly include statistical-numerical results that quantify performance of QAQC controls (field duplicates, preparation duplicates, blanks, standards etc). Graphics such as scatter plots, QQ plots, histograms and cumulative frequencies are used to represent the results. Statistical values including relative difference, absolute difference, relative variance, averages, T-test, and Zscores are used to quantitatively express the relationship between duplicate pairs ... but is an effective quality program just a statistical exercise? This paper aims to highlight the concept of ‘Quality Management’ (QM) as the precursor of continuous monitoring (ideally in real time) of QAQC results on Exploration, Production, Processing and Port samples, determined by trend analysis performed on a time and/or grades basis. Currently, there is a paradigm in the process of quality assurance that if individual data points fall within a predetermined acceptance limit then they are ‘acceptable’ and therefore suitable for informing operational and investment decisions. However, what is stated with respect to QM is that sometimes results found within the acceptance limits can indeed be internally biased, or show material deviations over a period of time, thereby impacting reconciliation results and/or potentially creating discrepancies with the final buyers. QM refers to the proactive detection of these ‘anomalous tendencies’, the approach and communication with the source of the information, the understanding of the reasons that cause the deficiencies, and the generation of agreed action plans to remediate the situation and ensure the consistency of results, in other words: continuous improvement on proactive manners.

Mar 22, 2022

Chlorine as a lixiviant for gold possesses a number of significant chemical and Idnetic advantages over cyanide but because of its corrosive and vaporous nature the method of implementation needs to be significantly modified. At comparable reagent concentrations the dissolution rate for gold in the C12/Cl- systems is some 10 - 100 times that achieved in the 02/CN system. The dissolution rate in the chlorine system is largely a function of the concentration of C12, Cl- and pH. Under conditions of low Cl', (less than 50 g/1), the dissolution rate begins to drop off dramatically over the pH range from 3 - 4. Increasing the level of dissolved chloride ions shifts the pH of this rate reduction to around pH 5 at 100 g/l NaCl, and to around pH 6 at 300 g/l NaCl.

Jan 1, 1991

By Ryan CG, Both RA, Mernagh TP, Large RR, Hunns SR, Gemmell JB

The Hellyer and Mt. Chalmers deposits are mound-style volcanic-hosted massive sulphide (VHMS) deposits in Australia. Textural, petrographic and microthermometric investigations of fluid inclusions in the Hellyer stringer system indicate that Type I, primary, liquid-vapour inclusions are 10-15 pm in size, and yield homogenisation temperatures of 170-220¦C in early 2A veins, 165-322¦C in main-stage 2B veins and 190-256¦C in late-stage 2C veins. These data suggest a waxing and waning thermal history. However, the average salinity remained between 8-11 NaCl equiv. wt % in all Stage 2 veins. At Mt. Chalmers, Type I inclusions up to 20 ¦m are found in quartz from the mineralised zone, and these inclusions yielded homogenisation temperatures of 160-268¦C and salinities of 5-8 NaCl equiv. wt %. Laser Raman spectroscopic (LRS) analysis indicates the presence of CO2 (

Jan 1, 1995

By J Euston

In the 1990s round flotation tanks were introduced as a result of the lower fabrication costs for larger cells. It was soon observed that round tanks held a number of further advantages over the traditional rectangular cells, such as better hydrodynamics, lower costs and reduced footprint per unit volume.In the last twenty years flotation cell sizes have increased almost exponentially and designs of 250 to 300m3 are a well established standard with plans for full scale pilot installations of 500m3. The option to install these large cells gives flexibility in circuit arrangements and allows efficient and economic matching of flotation lines with modern mill designs. The benefits of scale up are well known with reduced numbers of cells required, lower power costs per unit volume, etc. These benefits will be briefly reviewed with specific reference to the installation of 300m3 to 350m3 flotation cells at the Copperton Concentrator of Kennecott Copper in Utah, USA.The sophisticated techniques required to model these ‘supercells’ have led to a critical review of the fundamentals of flotation science and engineering. In addition to outlining the advantages of large flotation cells, this paper will review the science which supports, and occasionally challenges, the ongoing trend to larger flotation cells.

Aug 8, 2011

By O van Baalen

The Ernest Henry Mine is a copper-gold open pit operation situated in northwest Queensland, Australia. It is owned and operated by Xstrata Copper, with a current throughput of 11 Mtpa, however, open pit operations are scheduled to cease in mid 2011. The deposit dips approximately 45º and extends for at least another 400 m vertically below the final 530 m deep pit design.Construction and development of a sublevel caving (SLC) operation beneath the open pit was approved in December 2009. The feasibility design requires 39 km of development to be completed prior to production, which will commence in the fourth quarter of 2011. Initial ore production will be trucked and will increase to 3 Mtpa by the end of 2012, after which a hoisting shaft will be used. Ore production will then increase to 5 Mtpa in 2013 and ultimately to 6 Mtpa in 2016.Two 3000 kilo watt of refrigeration (kW(R)) modular refrigeration plants will be installed, as well as two 1600 kW mixed-flow fans capable of a combined flow rate of 780 m3/s at a total pressure loss across the mine of 2000 Pa. The main fans will be installed underground and will exhaust into the base of the pit.The following challenges were faced in the development of the ventilation and refrigeration network:•a relatively steep geothermal gradient,•tropical ambient conditions,•working under a wide pit shell, and•a large underground trucking fleet prior to shaft commissioning.A considerable number of ventilation studies were conducted with later studies extensively using Ventsim Visual™ mine ventilation software to complete the design process of the ventilation and refrigeration networks, including the comparison of several alternative designs. The paper focuses on design challenges prior to the commissioning of the hoisting shaft, and discusses resistance optimisation and occupational hygiene-related design parameters, such as heat and diesel emissions, production level ventilation, main fan selection and location, and refrigeration requirements.

Mar 21, 2011

Dimension stone is the term generally given to rock used in building construction. During early European history in Otago, locally available dimension stone products were easily obtained. Crude rock shelters built on river banks with schist rock within Central Otago soon gave way to more established and sophisticated permanent homesteads constructed with the same materials. Victorian architectural achievement is celebrated in Otago with many fine bluestone block buildings. When the University Council decided to build substantially in stone, it narrowly escaped disaster. It was well known at the time that brick in Dunedin was of an inferior quality and that it soon wasted. Rev Dr Stuart said before the 1879 Commission that æthe Council had some old-world notions and liked to have the University with some architectural styleÆ. Contemporary utilisation of dimension stone is generally restricted by expense to a simple veneer. Stone products produced from Otago quarries have found ready markets in other areas in New Zealand , particularly prior to the share market crash in 1987.

Jan 1, 1992

By T Honeyands, L Jelenich

We are currently witnessing large fluctuations in the relative price of ironmaking raw materials brought on by changes in the dynamics of supply and demand, market conditions, environmental regulations and technical factors affecting the iron and steelmaking process. From a customer perspective, it is the behaviour of iron ores in downstream processing that give them their value; their impact on the sintering or pelletising process and subsequently blast furnace ironmaking. It is therefore important to consider this value when developing projects, making mine planning/cut-off grade decisions and in setting price differentials for differing quality.This paper describes the use of the Marx value-in-use model to quantify the downstream value of lump iron ores. The Marx model consists of heat and mass balance modules for sintering and pelletising and a rigorous two-stage heat and mass balance model of blast furnace ironmaking. Mass balance and cost models are applied for steelmaking, casting and rolling. The use of a heat and mass balance allows accurate comparison of the impact of raw material properties on blast furnace operation. The impact of minor elements, such as alumina, silica and phosphorus, and metallurgical properties on ironmaking is described, and examples are given for the calculation of a lump premium.CITATION:Honeyands, T and Jelenich, L, 2015. Lump ore properties and their impact on value-in-use in ironmaking, in Proceedings Iron Ore 2015, pp 359–362 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015