Search Documents

By B J. Wight, R Mackay, S Kim

Improving the understanding of the processes governing ground movements in and around brown coal open cuts is of significant interest for both operating stability and rehabilitation. Brown coal, lignite, is a low-rank coal that is best described as a soft rock, with geotechnical characteristics that derive from its organic origin. It is well-known that low-rank coals exhibit creep behaviour; however, little has been reported on the impacts of chemical processes on brown coal creep behaviour even though organic substances are susceptible to chemical alterations and mining processes will contribute to changes to the geochemical environment; around most mines, groundwater flow patterns are altered leading to enhanced surface water infiltration. Here we study the deformation behaviour of brown coal in response to ion exchange reaction. Our experimental results show that for different ion exchange conditions different characteristics of secondary compression are observed. With the addition of Ca2+, the ratio between coefficients of secondary and primary compression (Ca /Cc) initially decreased, presenting a minimum value at the concentration of 0.005?M, then increased significantly. This implies the importance of ion exchange process for the long-term deformation of brown coal. On the other hand, increasing Na+ concentration did not affect Ca /Cc values significantly over all tested concentrations. The suppression of diffuse double layer was still observed for Na+-treated samples as increasing Na+ concentration decreases Ca values. From a practical perspective, this study did not consider the tertiary creep behaviour and eventual creep failure.CITATION:Kim, S, Mackay, R and Wight, B J, 2014. Creep due to chemical alteration of rocks – a case study in brown coal, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 61–64 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By M Franklin, C Puglisi, S Fitch

Implementation of a well planned and executed Management Operating System (MOS) can result in widespread improvements to operational performance but its success relies heavily on the investment by and engagement of the larger workforce with the project. Over the seven month period of the Telfer MOS project, significant improvements were achieved; a 20% increase in monthly hoisted tonnes from the open stope and sublevel cave operations and a 45% increase in square metres of ore extracted from the narrow vein operation. The Telfer MOS was undertaken with the intention that the project wasn’t solely about producing new tools, it hinged on the investment and behaviours of the personnel affected by these tools and alterations. To ensure that the project ran smoothly, the Byrnecut senior leadership team and their operators were heavily involved in the project’s development. In the initial stage, Telfer’s MOS project determined that the quality and accuracy of the information received in the form of radio calls to mine control and completed operator plods was questionable. This required an overhaul of the data collection and verification process in the form of altered operator plods, which was then cross referenced with the operator’s radio calls to mine control. Once the data collection and verification process was implemented, the Telfer team was then able to produce several tools with the aim of providing visibility to the data being captured and its implications. These tools allowed the mine foremen to determine whether equipment was being under-utilised and where they should focus their production efforts to meet monthly targets. Whilst the initial underground project is now complete, the implementation of MOS across the entire site is ongoing with significant operating improvements occurring.

Mar 15, 2021

By Rowe P, Rogers D, Warren M

Pressure cyanidation of the minus 10 micron slimes fraction of the Fimiston flotation concentrates for the recovery of gold values has been evaluated as an alternative processing route to the roasting and atmospheric cyanide leaching of the calcine. Laboratory and pilot trials have demonstrated that gold extractions of greater than 94 per cent can be achieved at cyanide consumptions of 12-24 kg/t and oxygen consumptions of 0.1-0.3 Nm3/t with total pressures of 1000-2000 kPa. Economic and operational assessment of several reactor configurations suggests autoclaves may be preferred over pipe reactors at treatment rates of 10 t concentrate/h.

Jan 1, 1996

By J H. Zietsman

The transition to more sustainable metal production is receiving much attention at present, and the iron and steel industry is at the centre of the conversation. New, more environmentally friendly production technologies, such as direct reduced iron (DRI) smelting furnaces, need to be developed in a short period of time. This necessitates increased use of computational modelling that incorporates more accurate material descriptions. The combination of large-scale multiphysics models of high-temperature processes with CALPHAD material descriptions leads to infeasible computation times. This can be resolved with the previously reported RapidThermo framework, which has been demonstrated to make equilibrium calculations orders of magnitude faster, within controllable limits of accuracy. In this paper, we explain how further material properties, which are important to modelling hightemperature reactors, can be added to the RapidThermo framework. This can improve the accuracy and usefulness of process and multiphysics models in the development of new technologies, which can significantly accelerate development cycles.

Aug 21, 2024

By T Roesch, M Neurohr, S Stratton

"Dwindling commodity prices are forcing today’s mining operations to increase output. Sometimes the solution is to upgrade the existing infrastructure; however, in most cases it has to be achieved with the same or reduced workforce and with the same equipment capacity through improved process efficiency and higher uptime.Measure, Manage and Improveis the mantra for this years’ Mill Operators’ Conference and while this in most cases relates to the above process efficiency, Siemens has set its focus on the availability and uptime aspect since unscheduled downtime is one of the biggest threats to any grinding operation. Pinion misalignments, resonance, unbalance and bearing and gear meshing faults in geared trains, as well as long-term changes in the condition of the mechanical components or structures and auxiliary systems in gearless systems are the main reasons for unscheduled downtimes in today’s mill drive trains. Our paper outlines the efforts that have gone into adapting conventional condition monitoring methods in conventional, pinion driven mill drive trains as well as gearless systems to capture the gradual deterioration of wearing parts or structural changes in the drive train not only on fixed speed application but also on variable speed applications with multiple operating points. The paper further explores the use of condition monitoring systems as a tool to assess spare thermal motor capacity to potentially push equipment beyond its nameplate rating, along with the process that was followed to correlate measured frequency spectra and envelopes to ambient and load data to understand the kinematics of the drive train.Citation:Neurohr, M, Stratton, S and Roesch, T, 2016. Advancements in Condition Monitoring on Mill Drive Trains for Proactive Maintenance and Early Fault Detection Purposes, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 263–272 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By P Gleeson, J Coombes, P Suresh, T McLennan

The last 20 years have seen a dramatic rise in the use of 3D visualisation and modelling for geological data, but there has been relatively little effort to do the same for the variogram models that underpin the standard estimation algorithms used by the mining industry.For kriging, one of the most used geostatistical estimation methods, specifying a variogram model is a critical part of the modelling process. Experimental variography is the primary method for approximating the theoretical variogram function from the available sample data, and then determining an appropriate variogram model from the approximations.The traditional tools used for experimental variography are limited to looking at subsets of the data and are often presented without reference to geographic space and geology. It can be difficult to know what input data is being used for a particular experimental variogram, and whether there is enough support in the experimental variograms to propose an appropriate model.To overcome these limitations, an innovative approach called situational variography has been proposed that visualises variograms in 3D alongside contextual geological and geometric data. Presenting variograms in this manner aids understanding of how the spatial variance relates to the underlying data.A 3D extension of the 2D radial variogram maps will be investigated which allows for dynamic exploration of the full experimental variogram cloud. These 3D experimental variograms are much easier to visualise situationally.A workflow for situational variography will be outlined and the advantages of the situational approach will be illustrated using a porphyry copper deposit.CITATION:Gleeson, P, McLennan, T, Suresh, P and Coombes, J, 2017. Situational 3D variography – determining the variogram in the context of geology, in Proceedings Tenth International Mining Geology Conference 2017, pp 191–198 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By I Treloar, T Elenbaas, E Isaaks

Critical reviews of grade control generally focus on blasthole sampling and the estimation of ore control block model (OCM) grades, with little or no attention given to dig-line design. For example, the estimation of block grades is deemed important as estimation errors lead to the misclassification of ore types and subsequent dollar loss. Recognition of the problem that the underestimation of block grades may be more or less costly than overestimation led to the application of loss functions to the classification of individual OCM blocks by ore type. The method is known as maximum profit selection (MPS). However, each OCM block may be misclassified a second time by dig-line design. Although each block may initially be assigned an optimum ore type by MPS, OCM blocks are seldom individually mineable by ore type. As a result, a common solution to this problem is the design of mineable polygons or dig lines loosely constrained by a minimum mining width. All material within a properly designed dig-line polygon can be mined and sent to a single destination such as the mill, stockpile or waste dump. These dig lines are often designed manually or by simple variations of computer-generated contour lines. They are generally suboptimal and result in additional misclassifications of ore types. This paper provides an algorithm for constrained optimum dig-line design where dig-line misclassifications are also evaluated through loss functions or MPS. Constrained optimum dig-line designs minimise the dollars lost by dig line misclassifications for a given minimum mining width constraint. A case study is provided illustrating constrained optimum dig-line design and subsequent benefits.CITATION:Isaaks, E, Treloar, I and Elenbaas, T, 2014. Optimum dig lines for open pit grade control, in Proceedings Ninth International Mining Geology Conference 2014 , pp 425–432 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By C C. Souza, S C. Amarante, A C. Arauj

All major companies now producing iron ore in Brazil currently employ or are planning to employ some sort of concentration method to upgrade their fine sized products (sinter feed fines and pellet feed fines). The criteria for the selection of the most suitable concentration method for each application include a series of parameters; the most important among them being related to ore mineralogy. This paper reviews the concentration operations currently employed in Brazil and shows how ore mineralogy plays a fundamental role in the selection of a given method. Examples involving gravity concentration (jigs and spirals), magnetic separation (Rare Earth wet drums, ferrous wheel, and Jones type magnetic separators) and flotation (especially column flotation) are discussed. Fundamentally important for the selection of a concentration method is the mineralogy of iron-bearing minerals and gangue minerals presented to the feed to the concentration unit operation. For instance, the presence of liberated quartz as the major gangue mineral for a pellet feed size stream generally indicates that flotation will be the best selection for the concentration of that stream. However, even if magnetite is present only in the form of crystal relicts within hematite grains, it may lead to the selection of either magnetic separation alone or a combination of magnetic separation and flotation for concentrating such material. Presence of gibbsite and/or kaolinite as the major phase containing alumina will also affect the selection of the concentration method in all cases. Again for the case of pellet feed size streams, kaolinite does not interfere with flotation whereas gibbsite tends to contaminate flotation concentrate (pellet feed fines) as it is depressed together with iron oxides and hydroxides during the reverse cationic flotation process.

Jan 1, 2002

By Minchinton A

CPeX is a non-ideal explosive performance prediction model. The model takes into account the rate of energy release, the extent of chemical reac- tion and the effect of confinement on energy release. The model resolves the explosive energy into `shock' and `heave' com- ponents as a function of explosive type, hole diameter and rock type. The predictions of the model are compared for a bulk emulsion, and a prill-doped bulk emulsion in soft rock. The predictions, based on calibra- tion of the model with simple unconfined detonation velocity measure- ments, show the significant effect of non-ideality on explosive Performance.

Jan 1, 1988

The Bellambi Coal Company Limited com menced longwall mining at South Bulli Colliery in 1965. At present it operates three long- wall units in two seams. Although results to date have been less successful than planned, it is apparent that this type of mining has tremendous potential in the particular conditions at South Bulli. Massive sandstone strata above the Bulli seam is the controlling influence on face conditions. The earliest equipment proved to be inadequate and the Company has progress- ively replaced and upgraded the roof supports and ancillary equipment so that the present units are capable of producing high and consistent outputs.

Jan 1, 1976

By P Cleary, G K. Robinson, J Hilton, P Wilson

Concern has been expressed that Vezins can be biased when used for sampling fine materials if the cutter speed is as high as the 0.6 m/s which is often used. Using modelling techniques that consider airflow as well as particles, we have endeavoured to investigate sampling bias as a function of the size of fine particles, cutter aperture, cutter speed, shape of cutter blades, and the size of the gap between the inlet pipe and the cutter blades. Using crude estimates of the rate of airflow and a simple model of a single particle moving through air led to an approximate rule that bias will not occur due to mechanisms related to airflow for particles larger than about 200 microns; and bias will always occur for particles smaller than about 40 microns. For particles between these size limits, the extent of bias depends on particle density, cutter speed and cutter geometry as well as particle size.CITATION:Robinson, G K, Wilson, P, Hilton, J and Cleary, P, 2012. Avoiding bias when using vezins for sampling dusty materials, in Proceedings Sampling 2012 , pp 109-114 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By M Doran

The Olympic Dam mine utilises 1.1 m to 1.4 m diameter raise bores for generating the initial slot void for most production stopes. Slot raise bores generally span two development levels ranging from 30 m to 50 m in height. Raise bores are reamed upward and typically leave a cap of rock equivalent to two times the raise bore diameter on the drill level (minimum 3 m). This provides safe access over the cap for subsequent production activities. It is therefore critical to ensure robust falling object protection for personnel accessing underneath, and in the vicinity of the raise bore void on the lower level. Recently, a number of mesh failures have occurred at Olympic Dam as a result of falling rock from the underside of the cap and raise walls. In addition, as Olympic Dam transitions to deeper and more challenging ground conditions, rockfall-off onto the raise bore protection mesh is anticipated to increase in frequency. This paper discusses the evolution of raise bore protection mesh used at Olympic Dam and presents results from recent site-based drop testing. This impact testing was carried out using a built for purpose object to replicate point loading and shear failure of mesh wires. Testing was also carried out on an improved mesh design which utilises two layers of Geobrugg high-tensile MINAX mesh. Results from the drop testing suggest an improvement in performance of the raise bore protection mesh is realised with the updated design.

Mar 29, 2023

By A Rantala, J Timperi and J Kaartinen, T Maksimainen, O Haavisto

"X-ray fluorescence (XRF) is the most common technique used for online slurry assaying in base metal flotation applications. Typically, assays from feed, concentrate and tailings slurries are used to monitor and control the flotation circuit, with possible additional sampling locations in other main slurry flows inside the circuit. The elemental content detection from the XRF spectrum is relatively straightforward as the spectrum contains element-specific peaks whose height corresponds to the element concentration in the sample. However, centralised XRF analysers measure the elemental concentrations line-by-line, which may increase the sampling interval for an individual line and cause unnecessary response delays, especially in large flotation plants. Reflectance spectroscopy is an emerging technique that can be used to obtain more frequent measurements from slurries. The measurement is based on the mineral-specific absorbance of light in the visible and near-infrared (VNIR) wavelength range. Due to this relatively inexpensive and simple measurement system, it is possible to conduct the measurement simultaneously in several slurry lines. However, the information contained in the VNIR spectra is more difficult to interpret as concentrations of all the minerals in the sample contribute to the measured spectrum and changes in solids content, particle size and mineralogy disturb the elemental content estimation. Therefore, frequent calibration of the measurement is required. This study presents the application of combined reflectance spectrum and XRF measurements for rapid online slurry assaying in a copper-nickel flotation plant. The XRF assays are utilised as calibration samples for the reflectance spectrum measurement, keeping the calibration model up-to-date. The rapid reflectance spectrum analysis is then used to provide an almost continuous estimate of the slurry contents, enabling further improved process monitoring and control.Citation:Haavisto, O, Maksimainen, T, Rantala, A, Timperi, J and Kaartinen, J, 2016. Reflectance Spectroscopy with X-ray Fluorescence for Rapid Online Assaying in a Copper-nickel Flotation Plant, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 85–92 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

A sample of tailings from a local, low grade (less than 2g/t) tailings dump was investigated for gold recovery. The tailings were very fine, with 90 per cent passing 30¦m and almost 60 per cent passing 10¦m. Tabling the coarse product from classification using a cyclone proved unsuccessful, with low recoveries being obtained due to high gold losses in the slime streams. Gold recovery by cyanide leaching was quite rapid, with recoveries of 85-90% being obtained in five hours. Lime and cyanide consumptions were 3 g/t and 0.1 kg/t respectively. Gold loading onto carbon was inhbited by the presence of the large amount of fines, so heap and vat leaching should be considered where the gold is recovered from a clear pregnant solution. Settling tests were conducted on tailings. It was observed that the addition of at least 3 kg/t lime or 0.4 kgh nonionic flocculant was necessary to promote settling of the tailings to generate a clear supernatant for gold and water recovery.

Jan 1, 1991

By Hang G, Hongtian X

In this paper, it is briefly introduced that China's Ordovician limestone confined-water menaces coal mining and Ordovician water is prevented and cured to secure the safety of coal mining. The theory of "Down-Three-Zones" is presented on the basis of research and practice in recent ten years. The concept of "Down-Three-Zones" of floor water-eruption is described clearly. Finally, the principle and method of applying the theory of "Down-Three-Zones" are discussed. 1. An Introduction of Damage: China is rich in coal resources. The conditions of coal field geology are quite complicated. There is an area of two million square kilometre of Karst limestone in nine million six thousand square kilometres of territory. The resources of underground water are rather plentiful, but this menaces coal exploration. Sixty percent of coal mines in China are damaged by limestone confined-water in different scales, particularly coal mines located the Carboniferous-Permian coal fields of the Ordovician limestone distribution area of Northern China. Because there is the 500-800 metre thickness of Ordovocian limestone and the well developed Karst containsl plentiful water, Karst water can have more than 100 Kg/cm pressure. Limestone aquifers have only distances of several metres or several decade metres to coal seam, Karst water can enter the aquituge and even the coal seam, large eruptions often occur. For example, a mine of 3 million ton production capacity had an eruption of 2053 cubic metres per minute. This is the largest confined-water eruption which has brought enormous economic damage and threatened the safe production of coal mining. Therefore, the prevention and cure of Ordovician water has immense advantage to the development of the coal industry. There are several decades experience in the prevention of Ordovician water-eruption in China. The prevention of Ordovician water-eruption has two kinds of plans. 1) dewatering and depression: it refers to dewatering of aquifers as roofs of seam and depression of aquifers as floors of seam in mining areas. 2) comprehensive prevention under the condition of having water pressure in aquiters. Due to enormous water, electricity, equipment and lots of other factors, the former isn't used extensively, the latter tits to China's actual conditions and is used widely. So-called comprehensive prevention under the condition of

Jan 1, 1988

By J Kwiri, T Zvarivadza, R Mitra, F Cawood

It is crucial to record ground movement of any magnitude to enable the safe and economical design of excavations and infrastructure. The DigiMine Laboratory is equipped with technologies to record such movements. This paper analyses the effectiveness of the Digital Mine instrumentation in recording earth movements in light of the Botswanan earthquake which occurred on the 3rd of April 2017 at 17:40 UTC. Recordings from the Digital Mine are compared with other ground sensing technologies which also captured the event (USGS and GEOFON systems). USGS and GEOFON system’s recordings suggest that, there are a number of possible mechanisms that could have resulted in the earthquake as discussed in the paper. Compared to the USGS and GEOFON systems, DigiMine system could not provide an analysis that could give possible source mechanisms. However, the system’s success in recording the Botswanan earthquake, is an indication that the system works and can be further developed or improved. For a comprehensive analysis, more data from various sensors needs to be collected. For example, DigiMine connecting to the national seismic monitoring system or to the local mine’s seismic monitoring system. Such connections will enable the development of a better self-analysis system and possibly prediction of future events. More importantly, it will contribute to better understanding of regional seismicity and its potential impact on excavation design. CITATION:Kwiri, J, Zvarivadza, T, Cawood, F and Mitra, R, 2018. How efficient is DigiMine technology in recording earth movements? A look at the Botswanan earthquake, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 414–419 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By Semple DG, Leach TM

A continued exploration programme has further defined the geology of the Tolukuma vein system, verified the resource indicated by Newmont, and identified potential for additional mineralisation. The resource at Tolukuma Hill, designated as Zone C, is a measured 440,000t @ 17g/t Au and 46g/t Ag with an additional indicated resource of 120,000t @ 16g/t Au. A diatreme breccia localised at an intersection of structures, and a relationship of gold to base metal sulphides, are highly indicative of a porphyry association. Typical epi-thermal features such as crustiform banded quartz and quartz pseudomorphing. platy calcite are also present and locally contain lesser gold mineral-isation. Pre-existing dilatant structures have acted as a host to the ore fluids, resulting in the formation of the semi-continuous Tolukuma-Gulbadi veins over a 1100m strike. A fluid flow model suggests that mineralising fluids were sourced from the diatreme margins and migrated laterally along dilatant structures. Bonanza gold grades are derived through fluid quenching in the flexure between a hanging wall split which hosts much of the Tolukuma Hill resource and the feeder graben structure. Thus, the relationship between the pre-mineral structural geometry and fluid upflow at the margins of a diatreme breccia, controls the ore setting. Potential for more ore remains within the Gufinis and the 120 veins as well as in the outlying Prospects.

Jan 1, 1994

The New Zealand Minerals Industry Association was incorporated as the NZ Mineral Exploration Association in 1982, with a membership that consisted of the gold exploration companies then active in New Zealand . As its membership broadened, it changed its name to the Mining and Exploration Association in 1994, and more recently the Minerals Industry Association. It is a non-profit-making incorporated society relying on voluntary membership, and is not funded by industry levies.   It has employed a full time executive director since 1988 when Robyn Ross was appointed, followed by John Pfahlert (1991 - 1996) and now with Doug Gordon managing the Association.   The Association is one of a number of organisations that represent the mining industry in New Zealand. Others include the Coal Association of NZ (CANZ), the Aggregate and Quarry Association (AQA), The West Coast Commercial Gold Miners Association and Minerals West Coast.   NZMIA membership comprises the main exploration and mining companies that account for over 80 per cent of New Zealand Æs mine output, and nearly all of its exploration investment. Its membership has expanded from gold exploration to encompass exploration and mining companies active in coal, gold, aggregates and industrial minerals.   The Association has developed a National Minerals Strategy that determines its priorities, implemented via a Minerals Industry Advisory Committee. This group was established six years ago to advise the Associate Minister of Energy on issues relating to the long term development of the minerals sector in New Zealand.

Jan 1, 2006

By OÆNeil G. R

The gold adsorption capacity of ash-char and ion exchange resin Zerolit F.F. (I.P.) was evaluated by obtaining Freundlich isotherms in the presence of selected variables. It was found that the presence of Na , 2+, Ca 2+ cations and SO4 , CN , S Z, 0 2- Zn anions prompted adsorption of gold onto the char and reduced gold adsorption capacity of the resin. Temperature, particle size of adsorbent and pH of solution were found to influence the gold adsorption capacity of char and the resin. The most efficient desorbent for gold adsorbed on the ash char was S2 ions. Optimum sulphide concentrations were found in the region of 1% Na2S. Investigation into the concentration of gold from actual carbon contaminated gold residue dumps in Kalgoorlie area onto ion ex- change resin showed limited success in one case and not so in another. Maximum gold adsorption by the resin appeared when cyanidation and sulphidization treatments were carried out simultaneously in the presence of the resin.

Jan 1, 1979

By Mason D. O, Tuckwell K. D

Whole rock geodhemical analyses from samples of Potosi gneiss within the Willyama Supergroup have been utilised to identify geochemical trends towards Pb/Zn ore positions. Although the analyses come from disparate sources they have been incorporated in the data base only if locational, sampling, analytical, lithological and stratigraphic descriptors were reliable. These data have been statistically analysed using programmes of the GASP software package. A discriminant function has been derived which permits Potosi gneiss associated with the Pb/Zn lode horizons in the Broken Hill domain to be distinguished from Potosi gneiss in a similar stratigraphic position in the Maybell Domain. In the "near ore" position the Potosi gneiss has significantly lower mean Na2O and significantly higher mean MnO. Also mean Rb, CaO and K20 are higher and mean Sr lower. This discriminant function serves to identify areas prospective for Pb/Zn mineralisation. A second discriminant function based on MnO, Si02 and K20/Na20 gives a semi- quantitative indication of proximity to ore.

Jan 1, 1983