Search Documents

By Hayward N, Sutherland D, Wilkie G

A pilot plant study has been made of the liberation characteristics of a nickel ore under different milling conditions. A series of runs were made ranging from fully autogenous grinding to semi-autogenous grinding with a ball load of 8%. The mill products were sized and assayed then analysed by QEM4SEM. This enabled a full liberation analysis to be carried out to see whether the autogenous grinding leads to improved liberation by promoting selective breakage. Though it is frequently claimed that fully autogenous grinding yields superior liberation this could not be detected in the present study.

Jan 1, 1991

By Barro L

Very large reserves of gas are contained in coal. Because of the low permeability of the coal gas flow rates are very low. Fracturing of the coal can be achieved by use of the nitrogen - foam frac techniques described but the flow rates after fracturing are not sufficient to support economic development. Fracturing of the seams in the Bowen Basin was as predicted but in the Sydney Basin no trace of the fracture could be found when development proceeded past the fractured well. Testing of coal samples has provided some insight into parameters affecting desorption Rates.

Jan 1, 1982

By D Sidea

There has been increased focus in Australia on large diameter raise boring for ventilation shafts and orepass excavation in good quality, brittle, highly stressed rock. As mining in many parts of Australia progresses to deeper levels, more vertical openings are being excavated in highly stressed ground conditions. However, whilst shafts have been successfully raise bored in highly stressed rock, it is often at a significantly increased risk of loss or damage to inhole equipment. It is important for both mine owners and contractors to have an appreciation of these risks at the planning and tendering phases of raise boring contracts. This paper provides an understanding of the risks associated with large diameter raise boring and a review of methods to predict failure in highly stressed rock.

Jan 1, 2005

By Weller KR, Restarick CJ, Stewart PSB

Following a detailed assessment of concen trator performance at Broken Hill South Limited which was reported in a previous paper, the fine grinding section was changed from a parallel arrangement of the two grinding circuits to a series arrangement, and the concentrator per- formance re-assessed. The change to series grinding had virtually no effect on the actual or potential capacity of the circuit to make a final product with 80% passing 100 mesh. However, the fresh flotation feed contained significantly less +150 mesh lead and +65 mesh zinc (material which was shown to float poorly), without an increase in the quantity of poor-floating ultra-fine lead and zinc. From the size-by-size flotation recovery data, it was shown that overall recoveries of both lead and zinc were approximately 1% higher than they would have been without this change in size distribution and it was concluded that this was a direct result of the change in grind- ing procedure.

Jan 1, 1972

By Lilly PA, Kavetsky AP

An empirical, kinematic model is developed which calculates the trajectory of individual blocks of rock in a blast, their point of impact in the muckpile and the final shape of the muckpile. The method is based on the determination of initial block velocity and requires input on stemming length, bench height, subdrill, burden, spacing, energy of explosive per unit length of blasthole, energy attenuation rate and resistance to movement. The model, which will form part of a comprehensive blast simulation package, has application in open cut mining in predicting muckpile geometry and the movement of grade blocks during blasting, which in turn impact on shovel productivity and grade control.

Jan 1, 1986

The rocks of the Serranias Chilla massif of Bolivia are a suite of metamorphosed Palaeozoic basalts and associated continental sediments. Whole-rock trace element geochemistry of the basalts suggest a calc-alkaline affinity and indicate that subduction extended as far north as the Bolivian Altiplano during lower Palaeozoic time.

Jan 1, 1990

By Yinxiang W, Chunlai Y

In older to improve efficiency of surface pre--grouting in sealing off water in heavily water-bearing strata, such as sandstone,siltstone and limestone, several methods have been used in China, they are ; intermittent pre-grouting, adjusting pre-grouting parameters and stepwise repeated pre-grouting methods. The paper describes effect of deviation on water sealing in pre-grouting. Deviation correction measures, like mechanical, technological and changing hole position methods have been introduced with satisfactory results in practical engineering projects without increasing the volume of engineering project and without causing delay.

Jan 1, 1988

By Hewitt D

A study of two laterite profiles developed on a serpentinite near Rockhampton, shows that loss of Si02 and MgO results in the relative concentration of Fe203, A1203 and a number of minor elements. Serpentine is broken down to form montmorillonite, goethite, quartz and kaolinite. Enrichment of nickel occurs, and it is shown that the element is mainly associated with montmorillonite and serpentine. Highest nickel values are associated with a zone in the profile which occurs at a depth of 10.5-22 metres, and the bulk of the nickel in this zone (42-80%) is associated with the

Jan 1, 1974

By Mahoney BK

The development of simulation models to reflect accurately the operations of a port and its associated transportation systems can be an expensive and time consuming process. However the complexity of such operations leaves little choice for other than simulation techniques since analytical methods are rarely appropriate. The development of suitable software has now reached the stage that these techniques can be used with confidence. Types of simulation models and their requirements are discussed together with the results from some recent applications to the planning and management of bulk terminals.

Jan 1, 1983

By K H. Esbensen

Sampling of grain, animal feeds (solid and liquid) including important mineral mixtures in the Danish agricultural sector is subject to an ongoing investigation with the objective of improving existing (suboptimal) sampling procedures. Results from the first six months are presented here; the project will continue for two more years and will include international collaborators (Australia and Canada). The Danish authorities have instituted a system of control analysis, which contains a set of mandated sampling and analysis methods. From a preliminary survey it was concluded that in fact all of the existing sampling procedures are not optimised in the light of Pierre GyÆs Theory of Sampling (TOS).

Jan 1, 2005

By Parks T. C

A low-grade disseminated nickel sulphide serpentinite ore from W.A. had a relatively high permeability after drying. Various techniques indicated that the permeability resided within a fine network of fibrous vein- lets and especially within coarse cracks along which the sulphides lay. The ore minerals were therefore open to selective extraction by chemical leaching. A IM ammonia-7.8 wt.o "ammonium carbonate" solution, oxygenated at 1 bar oxygen pressure and about 23¦C, released nickel, copper and cobalt from the sulphides, leaving a permeable residue of goethite, while calcium, magnesium and iron concentrations remained negligible in the leachant. The nickel and copper was electrodeposited directly from the pregnant liquor in a deposit which included 16.5 wt.% sulphur. Enhanced copper/ nickel ratios early in the extraction suggested that valleriite (not amenable to flotation) was leached preferentially. Th$ controlling influence of the pore structure was demonstrated by the dependence of leaching rates on the size of the ore particles used, and on the measured porosity of different ore samples. A 2mm size was probably the optimum for exposing sulphides to the leachant. Leaching was accelerated by increasing the temperature and oxygen pressure.

Jan 1, 1974

The Ramu chromite deposit occurs in the Marum Ophiolite complex and is the most economically attractive chrom-ite deposit in Papua New Guinea. Its lateritic nickel, chromite and cobalt potential has attracted several compan-ies to prospect the deposit.In the present work, the compositions of chromite in the Ramu lateritic deposit and coexisting olivine-chromite pairs in Marum Ophiolite dunite were analysed with the electron microprobe for Fe, Mg, Cr and Al. The results were used to determine the relationship between the cations in the tetrahedral and octahedral structures of the chromite. In addition, the Fe, Mg, Cr and Al cations of the coexisting olivine-chromite pairs were used to calculate the equilibrated temperatures of crystallisation of the chromite. The variation of Fe", Mg and Cr cation values of the chromite in relation to the calculated temperatures was studied by regression analysis.

Jan 1, 1994

By Whiting AN

Major changes in the world in recent years are changing the criteria for selection of future developments. Oil prices soared during the 1970's while commodity prices including metals and minerals fell. Many new independent nations, have been created and now control the resources in areas which were once part of great colonial Empires.

Jan 1, 1983

By Zharinov SE

Geonechanical modelling of island arc sys- tems and their analogs is investigated. Slow seismotectonic movements along the inclined deep fault zone under the compressive horizontal stress conditions are proposed to be the princi- pal mechanism controlling the structures and processes in the active continental margins. A model of shearing surface crack in an elastic half-plane is used for simulation. The main ele- ment of the model is viscous interaction bet- ween the crack sides, the viscosity varying with depth. To describe the stress-strain state of the medium an integro-differential singular equation is derived and solved numerically. The results of simulation are in good agreement with geological and geophysical data on the ac- tive continental margins.

Jan 1, 1987

Ore sorting is a high capacity, low cost method of preconcentrating ores and in some cases of producing a marketable concentrate. In most cases it is applied to run of mine material, immediately after primary crushing and screening in sizes ranging from 10 mm to 150 mm. Recent developments in bulk sorting of friable uranium deposits have resulted in machines capable of handling fine materials with sensing and separation being achieved on a zone by zone basis. Modern ore sorting machines rely on the synchronous operation of four internal sub systems, feed presentation, sensing, data processing and separation. A variety of different sub systems is available which can be combined in various forms to produce sorters capable of handling a wide variety of mineral types. The benefits in using ore sorting cover a wide range of situations and are applicable to both established mines as well as new mining ventures. Reduced operating costs, increased productivity, capital savings, energy and resource conservation and environmental issues are all part of the reason why ore sorting is finding rapid acceptance in today's mining industry.

Jan 1, 1980

By Wilson AF

Gold-silver mineralization at Cracow and Ukalunda in Queensland comprise quartz-filled veins, fissures and breccia zones hosted by propylitically altered volcanics and epizonal intrusions which are strongly fractured. The terrestrial volcanic facies, structural setting, type of alteration and complex mineralogy suggest these deposits are of the epithermal type.The 180 depleted character of the wall-rocks is consistent with the involvement of meteoric waters in convective hydrothermal cells associated with the vulcanism. The Cracow quartzes have remarkably low 6180 values from -2.0 to -3.4 per mil typical. of meteoric hydrothermal systems at high latitude, consistent with the inferred position of Australia during the Permian. 6180 values for the Ukalunda quartzes exhibit a wide range from 5.1 to 14.9 per mil which reflect the mixing of magmatic and meteoric waters, and a steep geothermal gradient.Further stable isotope and geochemical studies are in progress to establish the scale and morphology of the zones of anomalous 6180 and mineralogy in the wallrocks which constitute significant exploration targets.

Jan 1, 1984

By Juras ST, Krouse RH, Godwin CI

The Buttle Lake camp is in central Vancouver Island, southwestern British Columbia, Canada. The camp hosts world-class polymetallic volcanogenic deposits of Devonian, Frasnian age (370Ma). This paper describes an on-going sulphur and lead isotope study of the major orebodies.Sulphur isotopes were determined for sulphides (pyrite, chalcopyrite, bornite and galena) and sulphate (barite). Sulphide analyses are markedly different from sulfate. The differences are explained below in a unique model.Sulphide isotopic compositions cluster tightly (del34S -6.7 to 4.6), and demonstrate isotope reversals. Calculated temperatures of correctly ordered mineral pairs are unrealistically high. We conclude that the sulphides are in isotopic disequilibrium, presumably because of rapid precipitation from a quenched plume in an anoxic environment, and because of subsequent sulphide replacement.

Jan 1, 1990

By Blackham M

West Wallsend No. 2 Colliery is a new mine that is presently being developed in the New- castle Coalfield by J. & A. Brown & Abermain Seaham Collieries Ltd., a subsidiary of Coal & Allied Industries Ltd. It is situated near Barnsley and is some 15 miles by rail from the port of Newcastle. The mine will produce coal from both Bore- hole and Young Wallsend seams. The Borehole seam has a working seam thickness varying from 7 ft to 5 ft while the Young Wallsend seam presents a choice of two distinct working thick- nesses, i.e. 5 ft. or 8 ft, the upper 3 ft containing much high ash material. The inter- seam interval varies from 10 ft on the western edge of the area to more than 70 ft in the central portion. The Borehole seam lies at a depth varying from 550 ft to 750 ft and the overlying surface terrain is gently undulating bushland with limited surface development.

Jan 1, 1972

The Quiruvilca district, located 80 km east of Trujillo in north central Peru (Fig. 1), has produced over eight million tons of Cu-Pb- Zn-Ag ore from approximately 60 veins since 1789. "Quiruvilca means "sacred tooth" in Quechua, the lingua franca of the Incas. The expression refers to a prominent volcanic neck exposed several kilometers northeast of the district. The district covers an area of approx- imately 24 km2. The mines occupy the eastern quarter; workings underlie 6.7 km2 with a developed vertical range of 280 m. All pres- ently operating workings are owned by Corpora- cion Minera Nor Peru S.A., a subsidiary of ASARCO Incorporated. The oldest rocks in the area are Lower Cretaceous clastic sedimentary rocks exposed 7 km to the east. Lithologies include sand- stone, siltstone, shale, coal seams, and carbonates (Cossio, 1964). These rocks were folded and affected by regional low-grade metamorphism during the early Tertiary, 40-65 m.y. (Hollister, 1977).

Jan 1, 1987

By Harvey T, Kizil M, Bride J

Hydrogen sulphide (H2S) as a seam gas has occurred in several locations in the German Creek seam at Southern Colliery. This paper overviews the techniques developed to quantify the H2S content of the seam, overviews research into controlling and reducing H2S emissions from the seam, and details the procedures used to mine through the HZS zone in 702 longwall panel. Learning points from research and mining experience are reviewed for application in the next longwall block.

Jan 1, 1998