Search Documents

Excavation through fill material in underground metalliferous mines is usually avoided where possible, unlike in Civil Engineering application where excavation through soft ground is normally a matter of course. In the mining situation, where excavation is normally for access only, then excavation designs are engineered for mining in hard rock, except where previous lack of forward planning has made such excavation inevitable or a mining strategy sequence necessitates some mining through fill in order to achieve optimum recovery of ore. Historically, this has been the case, because of the lack of knowledge of the support characteristics of the fill material placed underground and the lack of knowledge of the composition of the fill material as placed. The expertise and experience available from mechanised excavation techniques in Civil Engineering application (shield jacking, forepoling, spiling, and soft tunnel boring, to name a few) are available for application to the underground mining situation if the need ever arises. This paper describes the situations in underground mining development where mining through fill material is required, the different types of fill material encountered and the types of support available

Jan 1, 1981

The design and operating characteristics of the hydraulic cyclone elutriator were described in detail by Kelsall and McAdam (1963), and the method of operation of the commercially available version, the Cyclosizer, is described in the manufacturer's pamphlet (Anon). Complete details of the operating procedure are given in the relevant operating manual (Anon, 1964).The cyclones which form the basis of the Cyclosizer (Fig. 1) under normal operating conditions produce typical cut sizes of 44, 33, 23, 15, and 10 µm for cyclones one to five respectively for material with a specific gravity of 2·7. At the end of the selected elutriation period each sized fraction is discharged and collected for subsequent assay or analysis but all material rejected by the fifth cyclone (e.g. minus 10 \lm quartz) normally passes to waste. When this material is needed for separate study, although its amount and average analyses can be calculated by difference, it may be necessary to collect more than 250 I. of very dilute suspension, flocculate the solids, allow to settle, and decant off the supernatant liquid.This procedure is cumbersome and inconvenient and the simple technique to be described may offer some advantages. The temperature of the water fed to the Cyclosizer is maintained at a constant value for added reproducibility.PROCEDUREThe present overall treatment of the subsieve material (minus 37 \lm) fed to the Cyclosizer incorporated several refinements compared with normal operation and these may be best illustrated by anactual example. Material to be cyclosized (25 to 100 g depending on size distributIOn and specific gravity) is completely dispersed in water at 23 QC by vigorous stirrmg, using suitable dispersants if necessary, in a...

Jan 1, 1974

ILZRO sights are locked securely on the targets of the expanded applications and ever-improving quality in the major market for zinc-coated steel. A wide range of ILZRO-sponsored research projects examine issues of formability, paintability, and corrosion resistance for traditional hot-dip galvanising, electrogalvanising, and ILZRO's own proprietary zinc coating, Galfan. Recent research has focussed on the on the interaction between Galfan and different substrate steels to determine optimum combinations for different applications. ILZRO enjoys an evolving role in providing the connection between research laboratories and marketing divisions through supporting research and services for the Galfan Technical Resource Centreò(GTRC) and the recently formed North American Galfan Development Authority (NAGDA). GTRC has just produced a new problem-solving manual that provides a comprehensive source of hands-on solutions for the many Galfan licensees throughout the world, and should contribute substantially to the reputation of Galfan as a consistently top-quality steel-coating product. Meanwhile, NAGDA is advancing the market with new advertising for Galfan based on superior corrosion-resistant qualities proven through ILZRO-sponsored research. Practical manufacturing issues remain at the forefront of ILZRO priorities, with research emphasis on cutting and welding zinc-coated steel to provide direct assistance towards improved product quality and a more secure market. Moving to the arena of die casting, when the specifier looks to zinc to fill a design need, ILZRO-sponsored research projects provide comprehensive documentation on metallurgical characteristics for every zinc alloy under almost any imaginable application. On-going ILZRO-sponsored research is integrating this wealth of data with sophisticated computer programs that model die-casting designs with ever-increasing accuracy, as other ILZRO projects lay the market groundwork for zinc in applications ranging from vibration damping to electromagnetic shielding.

Jan 1, 1993

During underground mining, rock mass changes can occur as a function of the mining sequence and excavation processes. Mining-induced rock mass damage can occur due to redistribution of static stresses and the application of dynamic stresses from blasting and seismic activity. These rock mass changes can result in a degradation of strength of the bulk rock mass and the remaining rock surrounding existing excavations. Rock mass damage near existing excavations which lead to excavation-scale instabilities such as rock fall, excavation closure, or visible rock mass fracturing can detrimentally affect the safety and profitability of mining operations.The focus of the current work was the prediction and assessment of damage to mine infrastructure occurring in relation to the blasting of a sublevel open stope. The study case involved a 60kt stope located in a highly-competent rock mass at a large Australian sublevel open stoping mine. The mine infrastructure of interest for investigation included local stope access development, critical access and haulage development crossing a regional-scale fault, an explosives storage magazine and a ventilation return air raise. The methods used to predict or assess the blast-induced damage to each infrastructure element in response to stope extraction were:- intact rock strength testing,- discontinuity mapping,- linear-elastic static stress modelling,- blast-damage mapping,- near-field blast vibration monitoring and analysis,- geophysical assessment using inferred stiffness and wave velocity methods, and- post-extraction void assessment.The results of the detailed blast damage prediction and assessment program at the mine site have been discussed by the primary author elsewhere (Fleetwood, 2010). The current work will address blast-induced damage to mine infrastructure as a result of extraneous blasting vibrations from stope production blasting. A method for predicting the amplification of excavation surface motions from reflecting body waves will be discussed as well as the results of damage mapping around the study stope. The results of the damage mapping program identified blast-induced damage that occurred to the surface of the explosives storage magazine and local stope access development. No damage was observed at the main fault crossing or return air raise where higher vibration amplitudes were measured or predicted.

Dec 6, 2010

By J Harmse

This paper deals with the modernisation of the brakes on an electrically coupled Blair multi-rope hoist and covers the removal of the old calliper brakes and hydraulic control system, and its replacement with brake discs, disc braking units and hydraulic control systems. The paper covers the braking requirements of the hoist, which is made up of two electrically coupled single-drum hoists, together with the theory behind the choice of brakes and control systems supplied. The paper also covers the project logistics that were required in order to install and commission the new brakes and control systems with the minimum disruption to production on the only rock hoist on a major production shaft. Items covered include the modifications to civil works, pre-installation of bearing lubrication systems, brake discs and hydraulics and the interfacing of the new hydraulic control system to the existing electric control system. It had to be designed to be compatible to a new electric drive and control system due for installation at the end of 2005.

Jan 1, 2005

By P Hogan, M Wells

Reflectance spectroscopy has become an established technique for mineral exploration and ore characterisation. However, there are few reported cases where the technique has been applied to the Hamersley Province channel iron deposits (CID). The Bonnie Creek CID, located ÿ140 km north of Newman in Western Australia, represents one of a number of CIDs recently discovered in the Hamersley Province. Reflectance spectroscopic analysis using the CSIRO HyLoggerÖ automated scanning system, in conjunction with X-ray diffraction and compositional analysis, was used to characterise and map the ore and gangue mineralogy in CID drill core. Using CSIROÆs spectral mineral characterisation scripts, it was possible to map the downhole distribution of the Fe-oxide abundance, hematite:goethite ratio and the gibbsite and kaolinite abundance. Spectral estimates of kaolinite abundance were found to be closely related to loss on ignition measurements at 650¦C and the spectral kaolinite abundance index provided a reliable estimate of the total weight percentage Al2O3 content. In addition, downhole HyLoggerÖ scanning of diamond drill core reliably mapped the distribution of kaolinite as supported by coincidentally elevated contents of alumina and silica. Furthermore, spectrally-derived estimates of iron oxide abundance were well related to assayed Fe wt per cent contents and use of the spectral iron oxide mineral index mapped the distribution of the goethite:hematite ratio, and demonstrated that material logged as high-grade ore in the Bonnie Creek CID was predominantly goethite-rich.CITATION:Wells, M and Hogan, P, 2013. Bonnie Creek channel iron deposits ore mineralogy - insights using the HyLoggerÖ technology, in Proceedings Iron Ore 2013 , pp 321-328 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Seedsman R. W

Good roads are essential in moving men and materials to and from the underground workplace. Coffey Partners International Pty Ltd (Coffey) has recently completed a underground coal industry funded project on underground mine road construction and maintenance. This paper discusses practical approaches to construction and maintenance of underground mine roads using transferrable civil technologies and innovative techniques. Mine pavements are generally low-cost (relative to civil roads), constructed to varying standards using locally available materials to best meet the mobility needs of the mine. Performance of pavements is thus largely dependent on the environmental conditions, quality of the available road making materials, maintenance policies and available resources. The paper will detail `what causes bad roads?' in various underground environments, available management strategies, construction and water control techniques, road maintenance and vehicle considerations.

Jan 1, 1995

By A Purvee, M F. Lee, L J. Mollison

Oyu Tolgoi is a large Cu-Au porphyry deposit in the south Gobi desert, Mongolia. The first of several deep, large-diameter, concrete-lined shafts, Shaft 1, is nearing completion. It will have a finished depth of 1380 m at a diameter of 6.7 m. These shafts will provide access to and hoisting capacity for block caving of deep underground ore. Geotechnical site investigations, and associated predictions of stability and ground support requirements, are compared against actual construction performance. Routine mapping is essential, along with checks against predictions and informing the contractor of ground conditions and variances.Advance rates are compared against predicted rock mass quality. A reasonable correlation exists between Qwall and advance rate. Overbreak and concrete liner thickness is related to the blockiness quotient, RQD/Jn.A ætool-bagÆ of just a few support elements (chain-link mesh, fibrecrete and 2.4 m long friction anchors and resin grouted re-bar bolts) was able to cope with the ground conditions encountered. QA/QC procedures are essential from the factory, through site storage to installation.

Jan 1, 2008

By N K. DavT, A Coggan

The performance of in situ, shallow water covers in controlling acid generation was evaluated at four recently decommissioned pyritic uranium tailings sites at Elliot Lake, Ontario, Canada. The tailings are acid generating, having a pyrite content of approximately five to ten per cent and a very low to non-existent alkaline buffering capacity. Adverse market conditions led to the closure of all operating uranium mines in the early- to mid-1990s, followed by rehabilitation and decommissioning of mine and waste management facilities. In order to control acidic drainage, all new and active tailings areas at Denison, Quirke, Panel, Spanish-American and Stanleigh mine sites were re-engineered to provide in situ submersion of these tailings under shallow water covers. The tailings impoundment dams were upgraded and reinforced or in some cases reconstructed, to minimise seepages and provide a minimum 1 m depth of water cover. With the exception of Stanleigh mine, which was closed in 1996 and rehabilitated during the late-1990s, the water covered Tailings Management Areas (TMAs) at other sites have been in operation for a period of six to nine years. The surface water quality at these sites is maintained at near neutral pH conditions by periodic addition of lime slurry to the established water covers. Additional treatment of effluent is provided as required to meet the discharge water quality standards. The performance of the established water covers at the sites was evaluated by analysing the annual equivalent limestone consumption data. The results were compared with the performance of an older, decommissioned Nordic TMA, which was rehabilitated using revegetation techniques. The water covers at these sites are performing as designed and acid generation has been reduced to low levels. Based on the total amount of yearly equivalent limestone required to maintain water quality in the water cover and at the effluent treatment plant, it is concluded that acid generation rate at the Denison TMA has reduced to less than 0.15 per cent of its pre-water cover conditions during normal operation and rehabilitation periods. In comparison to the revegetated Nordic TMA, the acid generation rates at Denison and Panel TMAs have decreased to less than 1.6 per cent of that at the Nordic TMA. The acid generation rate at the Quirke TMA was comparable or only slightly lower than that at the Nordic TMA because of its unique terraced cell configuration, having tailings in five hydraulically interconnected cells at different elevations. Historic acidity and oxidation reaction products, accumulated during normal operating and pre-water cover periods, are flushing from upstream locations to downstream cells, thus requiring much higher equivalent limestone additions for acid neutralisation and effluent treatment.

Jan 1, 2003

By Reed M. E, Cloutt B

Particulate samples were taken from the gas space in the settler of the Kalgoorlie nickel smelter using a vertical sampling probe and a specially designed isokinetic sampling probe which also quenched the samples. The vertical sampler was found to give unrepresentative samples. Suction thermocouple measurements of the gas temperature were also made. Using the isokinetic probe samples were taken at four points ranging from near the base of the reaction shaft to the base of the uptake at depths up to 1.5 m into the settler. Dust loadings and the sizing of the samples were determined. These parameters were found to be most affected by sample position and depth. The dust loading decreased along the settler but increased with depth. The loadings varied from zero near the roof to several hundred g Nm 3 near the slag. The dust also became coarser with increasing depth into the settler. Examination of the samples showed them to consist of spherical particles the largest of which were about 500 microns in diameter. The dust was mainly composed of mixed iron/nickel oxides with a little sulphide.

Jan 1, 1991

The present stage of economic development of the Broken Hill lode, attained after 40 years of active exploitation, leaves little opportunity for the study of the zone of secondary sulphides.Little remains of the oxidised zone, and the observations of the secondary sulphides of copper and silver can rarely be made on specimens collected in situ. A few specimens containing secondary...

Jan 1, 1927

By D Judkins N OÆLoughlin

"Basin Minerals Limited commenced exploring for conventional strandline hosted mineral sands (rutile, ilmenite and zircon) deposits in the Murray Basin in April 1997. This has resulted in the discovery of a major mineral sands field in the Douglas Project area, located southwest of Horsham in the Wimmera Region of Western Victoria. After the successful completion of a pre-feasibility study on these deposits in September 2000, the Douglas Project has advanced to bankable final feasibility study. This study should be completed by mid-2002 to allow a decision to commence production in 2003 at an expected rate of in excess of 500 000 tonnes of combined mineral sands products per annum. The field comprises several mineralised strandlines. The main ones of economic interest are from west to east, the four strandlines, Acapulco, Bondi, Bondi East and Echo. These strandlines at August, 2000 contain total Inferred Resources of 443 million tonnes at 4.7 per cent HM at a one per cent HM cut-off; ie 20.8 million tonnes of heavy mineral concentrate which in turn contains 11.3 million tonnes of ilmenite and leucoxene, 1.3 million tonnes of rutile and 1.6 million tonnes of zircon. The heavy mineral concentrate is coarse-grained with mean diameter grain size of the strandline deposits ranging from 130 to 160 microns in size. Major controls on the formation of mineral sands deposits in the Murray Basin are discussed with reference to the main mineral sand bearing, strand plain domains; the Central Strand Plain, the New South Wales Strand Plain and the West Wimmera Strand Plain. The Douglas Project deposits on the West Wimmera Strand Plain domain are characterised by wide zones of mineralisation with high-grade cores (>10 per cent HM), low stripping ratios, and a valuable economic heavy mineral suite comprising 60 to 80 per cent of heavy mineral concentrate. Constituent mineralogy of the heavy mineral concentrate of the overall deposits is; ilmenite (40 to 58 per cent), leucoxene (five to seven per cent), rutile (four to ten per cent) and zircon (four to 14 per cent). The Douglas Project Area appears to be endowed with significantly enhanced levels of heavy minerals compared to other areas of the Murray Basin due to its unique palaeo-geographical position. Long shore drift to the south of the basin has caused large quantities of heavy mineral to be trapped against the palaeo-cliffs and headlands of a rugged palaeo-coastline which includes in a major embayment, the Grampian Mountains, the Black Range and the Glenelg Complex. To the east, major faulting and uplift has brought the fine-grained WIM offshore deposits close to the surface and has resulted in erosional stripping of mineralised strandline deposits. This mineralisation has been recycled and reconcentrated within the younger strandlines to the west within the adjacent Douglas Project Area. These strandlines are thought to be younger than other mineralised strandlines discovered to-date in the Murray Basin. The Project Area strandlines are described; ie their morphology, geology and patterns of mineral distribution. The mineralogy of each of the strandlines is distinctive and variations are noted along strike and section."

Jan 1, 2001

This monograph presents a unified theory of adsorption and desorption of aurocyanide on activated carbon. This theory has proved useful for CIP/CIL carbon adsorption and Zadra and AARL elution process and equipment design; in accounting for the effects of various water qualities and process temperatures; and in the development of reagents to improve these processes. The theory presented is based on rigorous fundamentals : Classical Eyring theory links initial first order kinetics with Langmuir isotherm equilibria, and this isotherm is demonstrated for the first time to be a consequence of the activated complex postulate of Eyring theory. Simple extension to Freundlich conditions at high solution tenors is possible, but not presented. Supporting entropy data determined by the author includes practically all the pioneering CIP plants built in South Africa and Australia in the early 1980s.

Jan 1, 1991

By C E. Loayza, R M. Pinto, J G. G=mez

The Yanacocha District is located 20 km north of the city of Cajamarca, in the Northern Andean Orogenic belt of northern Peru.Gold production may have occurred as early as Incan times (Paverd, 2000), but modern exploration that began in the 1960s targeted only copper and silver. Newmont Mining Corporation, BRGM and Compa±fa de Minas Buenaventura began exploring for gold in 1983, with Newmont as operator.Initial drilling took place in 1985. By 1992 a reserve of 1.28 million ounces was reported (Teal et al, 2002).Production began at the Carachugo deposit in 1993.Current reserves are 31.7 million ounces at $US 325 per ounce at a grade of 1.03 ppm (Newmont Annual Report, 2003).The operating company, Mineral Yanacocha SRL (Newmont 51 per cent, Buenaventura 44 per cent and International Finance Corporation five per cent) produced 2.85 million ounces in 2003, making Yanacocha one of the largest gold mining operations in the world. The district is made up of a series of epithermal, high sulfidation style gold deposits and one gold-rich gravel deposit (La Quinua), aligned in a NE trend.La Quinua is not discussed in detail in this paper. The bedrock deposits are hosted in a Miocene volcanic package, the Yanacocha Volcanic Complex that also trends NE.Re gional NW striking Andean faults intersect the NE striking Trans-Andean Chicama-Yanacocha structural corridor (Turner, 1997), localising the district mineralisation. These two structural orientations dominate the district, controlling breccia and intrusion locations, and gold mineralisation. Discontinuous EW oriented fracture zones are interpreted as extensional and locally are important in controlling gold mineralisation.

Jan 1, 2004

White Cliffs Opal Field is situated in the Parish of Kirk, County of YulguIgra, New South Wales, about sixty miles from Wilcannia, and the River Darling. It is near the southern edge of the cretaceous basin of the interior of Queensland, New South Wales, and South Australia. Twelve miles south-west of the field, at Tarella station, a well sunk at the homestead reached silurian slates at about 127 feet, getting no water but about three miles north-west from the originally discovered and no central portion of the field, a well was sunk by the Momba, Pastoral cmpany, to a depth of 270 feet all the way through the cretaceous beds. At 250 feet a small supply of water was struck, but so much mineralised as to be quite useless. The temperature also was so high that a man could not keep his hand in it and Mr. Hogarth, the Momba Pastoral Company's manager, informs me that so corrosive was the action of the water, that a shovel left down the well for a fortnight, at the time of sinking, was completely eaten away.The well having now fallen in, I have been unable to obtain any of the water for analysis.The western termination of this portion of the cretaceous basin is situated about twenty miles from the present opal field, at which distance the slates, with (probably) devonian sandstones and quartzites resting unconformably thereon, commence to appear. The opal bearing country, as far as at present known, follows a more or less well defined line running north and south towards the northern end of the field, and north-east and south-west towards the southern extremity.

Downhole survey uncertainties observed at various De Beers operations prompted an investigation into their possible effect on deposit shape and volume. An accurately surveyed artificial æboreholeÆ was constructed and different downhole survey instruments tested. In this way an empirically determined error range of 0.1 per cent to ten per cent was derived for downhole survey data. These survey errors were applied to an orebody model at an existing mine. Visualising the sphere of uncertainty associated with a borehole trace using a general mining package (GMP) gives an indication of possible volume variance. The resulting orebody maximum and minimum volume scenarios for three different depths (200 m, 500 m and 800 m) are presented. For certain instruments and borehole angles, the 3D positional error can be as high as 100 m at 1000 m down the hole. At depths below 200 m the resulting volume deviations can become significant for borehole survey errors exceeding 0.35 per cent. At 800 m depth the volume difference can approach 25 per cent. These figures assume that the error is compounded. The impact of these downhole survey errors is greatest for pipe-like orebodies such as porphyries and kimberlite pipes. Subhorizontal sill-like orebodies (and coal seams) will not be significantly affected by these errors. The impact of this type of survey error needs to be stated (and quantified) and is significant in JORC classification.

Jan 1, 2009

Reduction of Iron Content from Silica by Gravitational Processes In this research work, it was attempted to reduce the iron contents (Fe2O3) in silica sample which was provided from Shenin silica mine using gravitational processes including jig machine, multi gravity separator (MGS), shaking table and spiral. The silica sample contains 93.75 per cent SiO2, 0.44 per cent Fe2O3, 2.78 per cent Al2O3, and 0.08 per cent TiO2 and the Fe2O3 has to be reduced to about 0.1 per cent or less than 0.02 per cent. Mineralogical studies and XRD analysis indicated the presence of haematite, pyrite and goethite as the major iron impurity phases. Mineralogical studies of polished and thin sections yielded that the degree of freedom of silica is more than 80 per cent in the range of -300 +212 mm. After elimination of fine particles, at first nine tests were carried out on crusher product (in two size fractions), wet rod mil product and scrubber product by means of Jig Machine. The best results were obtained with about 0.15 per cent Fe2O3 on rod mill and scrubber product which was not desirable. Thereafter 7 tests were carried out using shaking table; the best results were obtained with about 0.14 per cent Fe2O3 on rod mill and scrubber product which was not desirable. MGS showed the worst result in order to iron removal from silica which was not desirable. Finally 9 testes were carried out using spiral whish is the best gravitational separator for elimination of iron impurities from silica. The best result of spiral tests were achieved on scrubber product. In this test concentrate weight percent and its Fe2O3 grade were 82.32 per cent and 0.085 per cent respectively. Finally a test was carried out using 2 stages of spiral in order to develop flow sheet. In this test concentrate weight percent and its Fe2O3 grade were 78.8 per cent and 0.1 per cent respectively. This product can be used to produce float (clear flat) glass.

Sep 13, 2010

By T Christopher

The Campamento Au/Ag deposit, discovered by Linear Gold in 2004, is located in Chiapas State, southern Mexico. The deposit is hosted by a sequence of Pleistocene-Pliocene andesitic volcanic rocks that have been intruded by a feldspar-phyric porphyry complex. Measured and indicated resources are 852 000 oz Au and 3.46 million ounces Ag with inferred resources of 374 000 ounces Au and 920 000 oz Ag. Resources were estimated at a 1.0 g/t Au equivalent cut-off. This is an ABSTRACT only. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By M Byrne, P Newman, M Lindqvist

SomincorÆs Neves Corvo Mine, one of the largest copper producers in Europe, is currently constructing a paste backfill plant in order to replace cemented rockfill in its bench and fill stopes and possibly replace hydraulic sandfill in the drift and fill stopes. A 250 m flow loop was constructed at the mine and the flow properties of various paste blends were investigated. Cycloned tailings and total tailings were both pumped successfully as pastes and were also combined with waste rock for additional testing. The pressure losses in 102 mm and 154 mm diameter pipeline were recorded at flowrates up to 60 m3/hr and are presented at slumps from 120 mm to 250 mm. The data showed the sensitivity of paste mixtures to slight changes in consistency, confirming the need for accurate control during paste production and distribution. The flow results clearly showed the different paste behaviour between cycloned and total tailings pastes and the change in properties at low and high slumps. In addition to pressure loss data, strength testing was done on 38 mm and 82 mm diameter samples. Further strength testing is ongoing at the mine using fly ash as a supplement to cement, reducing the overall binder cost. Preliminary engineering for the underground distribution system is briefly discussed, with reference to the siting of the plant. The Neves Corvo Mine is particularly shallow and alternative methods to pumping were sought in order to ensure sufficient hydraulic head for underground distribution. The comparison of options had to take into account the capital and operating costs, the operation of the plant and the impact on the future expansion of paste fill utilisation at Neves Corvo.

Jan 1, 1998

By R Neivandt, Kane, M O&apos, D Browne

Newmont Australia is the operator of the Mt Leyshon mine near Charters Towers, Queensland. Mt Leyshon is an open cut gold mine, which processed on average 5.0 Mt of ore and produced up to 250 000 ounces of gold per year. Mining was completed in early-2001, followed by treatment of low-grade ore stockpiles for a further 12 months. Approximately 250 ha of waste rock dumps have been rehabilitated. Rehabilitation of two of the three tailings storage facilities (TSF) has been completed and the third is in progress. A field performance monitoring system that includes an automated meteorological station, large-scale lysimeters (measurement of net percolation), and in situ moisture content sensors (measurement of moisture storage changes in the cover material) were installed to monitoring performance of the cover systems placed on the waste storage facilities. This paper focuses on the installation and calibration of the in situ moisture monitoring system. The moisture monitoring system provides automated detailed in situ volumetric water content data above and within the large-scale lysimeters. A portable unit that provides spatial in situ moisture content measurements at additional locations on the cover system is also utilised. The paper will focus on installation and calibration of the in situ water content monitoring instrument in the waste rock, coarse cover material, and fine textured cover materials of the tailings facility and waste rock dump cover systems.

Jan 1, 2003