Search Documents

By Lawson F

A rotating disc geometry has been used to provide a uniformly accessible surface for a kinetic study of the cementation of the metals cadmium, lead and silver from dilute aqueous solutions. This work is an extension of studies carried out on the Cu/Zn and Cu/Fe systems for which the rection rate was found to be completely solution-phase mass-transfer controlled. When the amount of material deposited was greater than 0.2 to 0.4 mg/cm2 there was an apparent enhancement in e which is attributed to the formation of a roughened deposit. This same phenomeon was obseived in the Cu/Zn Cu/Fe systems. Again, the rate of reaction of each system investigated was found to be solution-phase mass ,..~sfer controlled.

Jan 1, 1970

By Nilsson C

Man has always been and will always be part of his environment, in ,a good, bad or indifferent manner. Until quite recently, this environment has been the atmospheric boundary layer above the land masses, and to a limited extent the air-sea interface of the oceans. Since the days when he lived in caves, he has built up a wealth of observations on these two environments,-with ever-increasing scientific precision which unfortunately until quite recently was completely insufficient for modern capabilities of data analysis. Consequently, in a sense, he has left in his wake thousands of years of missed, opportunities for making exact observations and increasing his understanding. The data of the past are lost and he has to be satisfied with what he can assemble from now on when his environ- ment, largely as a result of his actions, is exhibiting more and more rapid variations in time; in other words, time series of observations of phenomena are required, the length of which is critical for most purposes of analysis.

Jan 1, 1970

By H Catchpole, L FontbotT, J PTrez, M Ageneau, A Bendez·

In the world-class mining district of Morococha, epithermal polymetallic replacement bodies and veins overprint porphyry mineralisation and skarns related to subvolcanic intrusions of Miocene age, thus indicating ore formation in two different environments, separated in time or forming a continuum. The district covers an area of about 70 km2 in the north-western part of the Domo de Yauli complex in theWestern Cordillera of central Peru and is part of the Miocene polymetallic belt, also hosting the deposits of Colquijirca (Bendez· et al, 2008b) and Cerro de Pasco (Baumgartner, FontbotT and Vennemann, 2008). Multiple late-Miocene porphyry stocks intruded Permian, Triassic-Jurassic and late-Cretaceous sedimentary carbonate and volcano-sedimentary formations, as well as large mid-Miocene barren intrusions. Extensive field work and detailedmapping of different styles of orebodies suggest that ore formation in the area was related to the late-Miocene magmatism. Good outcrop conditions and superimposing of different mineralisation styles make Morococha an ideal location for studying ore-forming processes in a complex porphyry-related magmatic-hydrothermal system in which porphyry-to-epithermal transition occurred. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Baxter D. A

This paper, one of two written about the Queensland Railways Brunswick Street tunnels presented at the VIII Australian Tunnelling Conference, 1993, describes the design and monitoring aspects of the railway tunnels built between Central Station and Brunswick Street Station.The design was mainly influenced by the need to minimise settlement of buildings above the route. The performance of the design details and the monitoring of the tunnels are briefly described.Appendices include extensions to the work of Curtis in the analysis of circular tunnels in a viscoelastic ground.Reference: Asche, H R and Baxter, D A, 1993. Design and ground support monitoring of the Brunwick Street rail tunnels, Brisbane, VIII Australian Tunnelling Conference.

Jan 1, 1993

By F Hungerford

"In-seam drilling has been undertaken for the past 30 years for gas drainage to reduce the risk ofoutburst and lower the concentrations of seam gas in the underground ventilation. The drillingpractices have reflected the standards of the times and have evolved with the development oftechnology and equipment and the needs to provide a safe environment underground. Earlypractice was to adapt equipment from other fields, but with changing emphasis, research anddevelopment by the coal industry has created specifi c equipment, technology and practices toaccurately place in-seam boreholes to provide efficient and effective gas drainage."

Jun 1, 2012

By King D, Dickinson S. B, Matheson R. S

Commencing in 1956, Rio TInto Australian Exploration Pty Limited in association with Electrolytic Zinc Co of Australasia, Limited, has been carrying out a mineral prospecting program in North-West Tasmania over an area of about 4000 square miles.The program has comprised extensive airborne geophysical surveys, detailed geological mapping, ground geophysical and geochemical investigations. Out of the wealth of new data, and the examination of previous records, has emerged a new structural concept of regional ore control and distribution in North-West Tasmania. This roncept stems from the discovery of an ancient 'fossil' rift valley (graben), named the Owen Rift Valley, along which are located the major mines of the area and numerous well-known prospects. The known mines and prospects from north to south include Mt Bischoff (tin); the Pinnacles (zinc, lead, ropper); the Chester (pyrites); Rosebery-Hercules (lead, zinc, ropper, silver, gold); Mt Tyndall (lead, ropper, zinc); Comstock and Tasman (copper, lead, zinc); Mt Lyell (copper, pyrites, gold); Mt Jukes and Mt Darwin (ropper). The identification of the West Coast (Owen Conglomerate) Range as a fossil rift valley is due to Or B Campana, who carried out extensive geological mapping and interpretation work, and who, with S B Dickinson, are the senior authors of this paper.S B Dickinson, who introduced B Campana to the geological problems of West Tasmania, had previously investigated the Mt Lyell and Rosebery mining fIeld, to which reference is made in this work.D King assisted in the regional mapping and in providing numerous data on the mineral distribution of the area.R S Matheson rontributed to the fmdings on ore emplacement and rontrol in the discussions held on this subject. They are accordingly included as joint authors of this paper.Credit is also due to E McCarthy, who interpreted the geophysical results, and to J H Rattigan, who compiled the preliminary geological maps from published documents and by photo-geological methods.G Hall and V H Cottle, of the Electrolytic Zinc Co in Rosebery, provided invaluable geological data and suggestions in the course of the survey, and made a constructive criticism of the manuscript of this work. The airborne geophysical survey carried out by the Adastra-Hunting Geophysics Ltd company, furnished useful data which substantiated many of the fIndings on the stratigraphic and structural relationship. The Mines Department of Tasmania and S W Carey, Professor of Geology at the University of Tasmania, were instrumental in initiating the regional survey and provided the published and unpublished geological literature on the area.The authors also wish to acknowledge the invaluable assistance received from the Mt Lyell Mining and Railway Co in Queenstown, which made available the more recent geological and mining documents rompiled by M L Wade and M Solomon.

Jan 1, 1994

By Nixon C. A

The exploration of Mount Isa Mines' new copper source will require the development of a five kilometre 4.7 x 5.5 metre blind decline commencing 1000m below the surface and extending to 1600m below the surface. With virgin rock temperatures approaching 60¦C, the ventilation strategy represents a complete departure from any previously used at this mine, in that refrigeration becomes essential. The use of direct water to air cooling techniques has become commonplace in mines throughout the world and their application is being adopted at Mount Isa Mines. A heat load simulation routine has been implemented to allow for the design of refrigeration requirements, as well as to aid in the selection of diesel or electric equipment. This enabled planners to determine the size of a surface based refrigeration plant. Future refrigeration demand for expansion into the ore production stage has also been investigated.

Jan 1, 1988

Computers and other microprocessor technology lead the world of technological change. Nevertheless, the real advances in the world at large are not necessarily in the computer industry, but in the industries whose economics benefit most by the advances that this computer revolution makes possible. The minerals industry has always been in the forefront of this advance. Technological change in the era preceding the industrial revolution, and the mining industry's part in it, provides an instructive lesson for what is happening today. Strong parallels can be drawn for predicting future advances. With each technological advance allowing more efficient production comes a re-alignment of economics - absolute and relative changes to prices, to quantities demanded, and to other market characteristics. This re-alignment applies not only to the mineral industry, but also to the world at large. Adaptability, rather than technical advancement per se is the key to survival and growth in a changing world. 'Adaptability' as a concept is easy to support. As an operational philosophy it is not so easy to implement. As a goal for planning, it is much harder to quantify. A fixed scenario of a future world may provide helpful guidelines, but a scenario that demands adaptability to an uncertain future world is much less definite. Of course, everyone else in the world is also uncertain about the future, and they are making their plans using different assumptions. This virtually guarantees that our future will turn out different to our expectations. This is in part what Hayek (1945) calls the 'knowledge' problem. Until now, most of the planning and technical research undertaken in the world has ignored this problem. This ignorance is a luxury that we can no longer afford. The paper looks at the history of technological change and highlights the characteristics of successful technological revolutions. 'Adaptability' to unforeseen circumstances is the key to success in this environment. The paper examines the knowledge problem from the perspective of the mineral industry, and suggests a number of directions for maximising the returns from application of computer technology in this important area.

Jan 1, 1995

Since the announcement of early experimental work on rotating magnetic field (RMF) separation at the Sixth Mill OperatorsÆ Conference in 1997, the concept of RMF separation has been developed and tested further, and a range of separator designs is now being developed for the mineral processing industry. Shortened, but full diameter, prototypes of these designs are now available for test separations. The main advantage of RMF low and medium intensity attraction separation is the significant reduction in particle entrapment. This reduction is so significant that RMF separators are capable of operating very close to their theoretical limit for separator precision. This makes small laboratory RMF attraction separators ideal for low to medium intensity magnetic sample analysis, and larger separators ideal for applications requiring sharp magnetic susceptibility splits. Feedrates and separation rates are comparable to those of conventional attraction separators. Although RMF attraction separators are now well advanced in development, RMF rotation separation is still in the early experimental stage. The exception to this is the dry particle rotation eddy current separator that offers eddy current separation of small non-ferrous metallic particles from about 2 mm down to about 100 microns. Wet small particle eddy current separation is also possible, but has not yet been developed to a practical stage.

Jan 1, 2000

By D Obeng, D Alexander

Over the past five years, commodity prices have been high and the focus of many plants has been æthe more metal the better, at whatever costÆ. In the recent economic crisis, the focus has shifted more to reducing the cost of production and operating at higher efficiency. Since 2002, JKTech has partnered with the Century mine in north-west Queensland to transfer technology and understanding through the good, bad and ugly economic environments, using methodology and techniques arising from research at the Julius Kruttschnitt Mineral Research Centre (JKMRC) and other research institutions around the world as part of the AMIRA International P9 Project. The JKTech studies were concentrated around the primary zinc circuit. During this period, Century expanded the primary zinc regrind capacity, installed additional scavenging capacity, installed and commissioned a Jameson cell for concentrate cleaning in the carbon preflotation circuit, and installed additional primary grinding capacity. Flotation circuit models were developed for each of the survey campaigns and enabled opportunities for further improvement to be identified, implemented and tested in the subsequent campaign.

Jan 1, 2009

This work was instituted to investigate the microscopic structure of brown coals by means of microtome sections cut from them. It was found to be essential to impregnate the coal with some material prior to cutting, because of its powdery and crumbly nature. Of a number of impregnating materials tried, e.g., glycerine gum, gelatine, by far the most satisfactory was paraffin wax. Samples of brown coals for section cutting must be moist. When obtained, they should be put immediately into air-tight tins, and, if they are not to be used for some time, it is desirable to keep them under water containing a small amount of formalin. If the sample is allowed to dry in air, it becomes too hard to be cut. It cannot be softened again even by prolonged soaking in water.PREPARATION OF COALSmall rectangular, blocks were cut from the sample with a chisel and a strong scalpel. The largest block prepared was 3·2 x 2·5 x 0·6 cm. The faces of the block from which sections were to be cut were approximately levelled before treatment. The block was then painted carefully on all sides with two coats of warm aqueous agar, approximately 2 %. This prevented crumbling and breakage of the block during treatment. When the agar was set, the block was placed in water, and all the air removed with a vacuum pump. The water was replaced first by alcohol, then by chloroform, by the usual step transference of a series of liquids, in each of which the block was placed for 24 hours: Ethanol %, 10, 20, 30, 50, 70, 85, 95, 100 (three changes); Ethanol-chloroform, 3: 1, 1: 1, 1 : 3, chloroform pure (three changes) '. The blocks were then embedded in paraffin of melting point 56-58°C. Fresh...

Jan 1, 1947

By Morrison R. D

This paper describes major events in the design, construction, camtissioning and operation of the Elura concentrator. It covers the period fran September, 1974 when laboratory testwork on drill core cotmenced to March, 1983 when the concentrator catmenced operation on run of mine ore following successful completion of initial ccnmissioning tests. The concentrator was designed to treat 1.1 million tonnes of lead-zinc-silver ore per year with a plant availability of 89 per cent. This treatment rate has been achieved for test periods.

Jan 1, 1983

By C McIntosh, M van Dam, N Whetter, R Lane, M McCulloch

Mine geology is understood through synthesising large amounts of structural, lithological, geochemical and geophysical data derived from the original topographic surface, drilling and surfaces exposed and removed during open cut and underground excavations. Computer- generated 3D geological models of any mine environment need to incorporate large amounts of information but also should be regularly updated with typically frequent influxes of new data. Geologists with the local knowledge should also be involved in the model construction, enhancement and interpretation, placing ease-of-use functionality high on modelling software requirements. Implicit-style modelling is a fast-growing area of 3D geological software development where interpolated surfaces such as lithology boundaries and bedding orientations are defined mathematically as functions rather than explicitly through coordinate meshes. The functions are constrained only by the data and not by an artificially imposed grid; therefore, implicit 3D modelling can process a lot of information quickly and routinely operate on original data (such as observed contacts and structural data) rather than on evolved iterations and interpretations. 3D mine geology models can be readily updated with new data, which can be automatically reprocessed to test ideas in near-real time. Implicit, function-based 3D modelling software has been applied to the Globe-Progress mine in West Coast, New Zealand. This structurally- hosted gold mine has some geometrical conundrums that are in part being resolved as excavation of the open pit proceeds. The relationship of the Globe-Progress ore shoots to hanging wall and footwall structure is still not fully understood, however, and 3D geological modelling is assisting with visualisation and testing of structural hypotheses. The modelling is also capable of predicting areas of bedding defect slope failure in yet-to-be excavated parts of the mine.

Jan 1, 2009

By T Laurencont

The Queensland Department of Natural Resources and Mines (NR&M) accepted the environmental liability for the Mount Morgan minesite in 1991. This gold and copper mine located 38 km southwest of Rockhampton had been in operation for more than 100 years. Mining leases are still active while the feasibility of a reprocessing operation is carried out. From 1993, NR&M have operated a seepage interception pumpback system which has reduced the chronic load of acid rock drainage (ARD) to the adjacent Dee River, a tributary of the Fitzroy River system. In early-2000, it was recognised that a ten-year plan for rehabilitation of the mine, along with significant funding would be required if a long-term sustainable rehabilitation strategy was to be implemented at this minesite, ultimately making the seepage interception system redundant. A rehabilitation planning workshop coordinated by NR&M was held in May 2000. This workshop brought to the mine a range of technical expertise and key stakeholder groups. This workshop provided a technical forum for review of studies undertaken and to identify priority projects, which needed to be undertaken in the future to more clearly define contaminant sources on the mine site and to prioritise the rehabilitation program. Stakeholder consultation enabled the project team to be clear on community and other government (eg Environmental Protection Agency) expectations. It is clear that the future of the economically depressed community of Mount Morgan will be reliant on the careful management of the significant heritage values at the minesite for tourism, education and research. In the first year (2000), priority studies were initiated, which included whole of site studies on water balance, contaminant sources and a review of occupational health and safety and environment of the minesite and conservation and heritage scoping. Baseline vegetation and soil materials surveys were also initiated. The outcomes of these studies helped to shape the work program for the following year, while providing a basis for an additional funding application, which was granted. The second year of studies focused on building upon the existing baseline studies completed. In addition, studies focussed on addressing the priority issue of contingency planning for overflow from the open cut pit in accordance with best practice management of release water and river monitoring strategies were completed. Completion of these projects over the next six months will enable the optimal rehabilitation strategy to be defined in 2003. This optimal strategy may require the use of a water treatment plant for part of the ten-year program to provide space in the open cut pit for the deposition of ARD contaminant sources (eg waste dumps, tailings). It is envisaged that some sources will be rehabilitated insitu while others will be relocated to the open cut pit. Implementation of this strategy will be dependent on subsequent funding.

Jan 1, 2003

The South American mining community leads the world in recognition and adoption of the latest grinding mill relining technologies. Clearly this region has recognised the benefits of improved relining performance as a defence against the Global Economic Crisis. Five of the six RUSSELL TWIN 8 Mill Relining Systems, ordered to date, are either operating or being manufactured for South American mine sites. The sixth is for Sino IronÆs Cape Preston Project in Western Australia. This paradigm shift, towards very short relining times, aims at displacing mill relining activities from the critical path of concentrator maintenance shutdown schedules. The first uses of the RUSSELL TWIN 8 Mill Relining System have seen some of the highest semi-autogenous grinding (SAG) mill new liner placement rates ever observed by Russell Mineral Equipment (RME), as would be expected with two, independent Machines working simultaneously in the one mill. The liner replacement rate, averaged over the whole reline is good (27 per cent improvement over single Machine System in the same mill) but short of full potential. This modest result can be attributed to reline crews unfamiliarity with RUSSELL TWIN 8 System operation. This paper compares a sample of conventional (single machine) RME Mill Relining System performance data with one ædouble headÆ mill liner handler by others. Early performance of EscondidaÆs new RUSSELL TWIN 8 System performance is then compared with recent single machine data from Escondida, immediately prior to RUSSELL TWIN 8 commissioning. RME and Escondida look to constantly improving RUSSELL TWIN 8 System performance as full operational familiarity is achieved. The preparation of this paper revealed a need to develop a global industry standard for mill relining data collection. A web based platform to develop data collection templates is also discussed in Appendix 1.

Jan 1, 2009

The Ardlethan tin concentrator had dete riorated considerably in metallurgical per- formance, maintenance and plant availability. This problem was compounded by low tin prices and International Tin Council quotas. Mid- 1976 figures were: throughput - 1300 tonnes per day, availability 83% and metal recovery 537. Major problems existed throughout the circuit from crushing to tailings disposal and with morale, staffing, and housekeeping. With the lifting of the quotas in June 1976, management provided funds to implement a major rehabilitation programme and some fifteen major projects, at a cost of about $1.3 million have been completed to date. The change in performance has been dram- atic, and end of 1977 performance figures are: throughput - 1700 tonnes per day, availability 90% and metal recovery 65%.

Jan 1, 1978

Gunpowder Copper Limited processes 1,000 tonne/day of Mammoth ore in a conventional flot- ation concentrator. Run of mine ore is prepared for flotation by three stages of crushing and two stages of ball milling. The concentrate, in which the primary copper mineral is chalcocite, is solar dried and exported to Japan. The history of operation is summarised, and plant practice and metallurgical problems are discussed.

Jan 1, 1974

A mineral exploration manager's prime function is to provide a frame- work within which new mine production can be achieved. As part of this framework, the manager should know his employerb future requirements, and should direct exploration towards those particular mineral commodities which indicate satisfactory growth in consumption and price. Selection of these commodities can be assisted by studies of world reserves, and long term trends in price and consumption. Exploration planning is most efficient with an assured and reasonably uniform supply of funds.

Jan 1, 1980

By R Bunduwongse

The oil crisis had repercussions throughout the world and most importantly on mining, where the drive to reduce the use of liquid fossil fuel led directly to the appearance and subsequent growth in the design of mobile crushers in late 1970s early 1980s, which heralded a new era in both quarrying and mining. Even though mobile crushing has now become common, even preferred in the quarrying industry, this has not been the case in mining. This paper looks at why, in spite of the initial optimism, this technology has yet to gain full acceptance in the mining industry. The paper examines some of the problems that have been encountered in the past and offers suggestions as to how they can be avoided by applying the appropriate technology. It then takes a look at the successful application of the semi-mobile in-pit crushing system used by Italian Thai Development Company (ITD), on the Mae Moh Phase 5 contract and examines how the techniques used successfully there could be applied to the industry at large.

Jan 1, 2007

By F J. Rios

In the eastern high-strain domain of the Quadrilßtero Ferrffero, Brazil, hard and soft high-grade hematite ore may occur as schistose bodies in shear zones mainly related to the Cambotas-Fundpo thrust system. These orebodies are almost entirely constituted of oriented specularite platelets that develop both as a product of crystal-plastic deformation of hematite and solution-precipitation processes. Both mechanisms interact in the partitioning of the strain, while solution-precipitation is responsible for the precipitation of hematite and localised leaching of silica resulting in the formation of syntectonic ores. The analyses of fluid inclusions from specularite crystals of the Conceitpo and Timbopeba deposits, located in the northern and southernmost areas of the eastern high-strain domain of the Quadrilßtero Ferrffero, were studied using infrared microthermometry and Synchrotron x-ray fluorescence. The results indicate the participation of highly saline aqueous H2O-NaCl fluids containing other additional cations (Ca, Fe, K and probably Ti) in solution and homogenisation Temperature (Th) averaging between 130¦ - 190¦C. However, the partial fusion of metastable saturation phases indicates crystallisation temperatures of approximately 400¦C. The mineralisation process produces high-grade orebodies as well as Fe-rich specularitic itabirites that are explored in that area. The shear zones are related to thrust faults mapped and interpreted as related to the PanAfrican/Brasiliano Orogeny that affected the Quadrilßtero Ferrffero, thrusting the Paleoproterozoic platform sequence of the Minas Supergroup over Mesoproterozoic quartzites of the Espinhato Supergroup. They intersect and even overprint an early metamorphic and tectonic fabric of Paleoproterozoic age (Transamazonian Orogeny). The geological and fabric relationships lead to the conclusion that the fluids involved in the mineralisation were most probably of external origin, of still unknown source (possibly igneous), during the closure of the Spo Francisco Craton.

Jan 1, 2005