Search Documents

In 1874 a stockman, JE Wright of Foxlow Station, recognised copper mineralisation when he was about 12 kilometres south of the station. The find was on the banks of the Molonglo River. Several small mines were soon operating along the ridge above the river, and the village of Captain's Flat was established.One mining company established in the 1880s was Lake George Mines. It's name was to remain synonomous with the name of the town until mining and treatment ceased on 11 March 1962.

Jan 1, 1993

By Vogwill R. I J

The Boddington Gold Mine, operated by Worsley Alumina Pty Ltd, is located about 100 km south of Perth and is one of the largest-producing gold mines in Australia.Multiple open pits are planned and several extend below the water table, through the deeply weathered lateritic profile and into the underlying Archean bedrock. Groundwater related mining problems, such as poor trafficability, wet floor conditions and slope instability began to occur early in 1990.The mine is located within Archean greenstones which are steeply dipping and faulted. Rock types include mafic to felsic volcanics, pyroclastics and sediments. These rocks have been regionally deformed and metamorphosed and are intruded by quartz micro-diorites and post-mineralisation dolerite dykes. Deep weathering has produced a typical oxide profile consisting of laterite, clay and saprolite zones underlain by weathered to fresh bedrock.

Jan 1, 1993

By O N. Antzutkin, W Forsling, K J. Pike an

The adsorption mechanism of three different O,OÆ-di-alkyl-dithiophosphate (dtp) collectors, K[S2P(OR)2] with R = Et, i-Bu and i-Amyl, on the surface of synthetic chalcocite (Cu2S) was studied by means of solid-state 31P CP/MAS NMR spectroscopy. The morphology changes on the conditioned Cu2S surfaces, in the collector concentration range 0.1 - 10 mM, were also monitored with scanning electron microscope (SEM). In order to assign Cu(I)-dtp species on the surface of Cu2S, the corresponding bulk Cu(I)-dtp compounds, which are clusters of the monovalent copper containing either Cu6(antiprismatic) or Cu8(cubic) cores, were synthesised, and characterised by means of solid-state 31P CP/MAS and static 65Cu NMR. Further investigations on the crystal habits of the bulk systems were carried out by powder x-ray diffraction and SEM. A comparative analysis of the 31P chemical shift and chemical shift anisotropy (CSA) data estimated from the experimental NMR spectra of the polycrystalline bulk Cu(I) dialkyldithiophosphate complexes was used for assigning the 31P resonance lines in the NMR spectra of the collector treated Cu2S powder samples. The species formed on the synthetic Cu2S surfaces were assigned to polycrystalline phases of: Cu6L6 with L = Et2dtpû, Cu6L6 and Cu8L6(S) with L = i-Bu2dtpû, and Cu8L6(S) with L = i-Amyl2dtpû. A heterophase autocatalytic step process of both formation and growth of solid CuxLy (L = R2dtp, x = 6 or 8 and y = 6) complexes on the collector treated Cu2S surface is proposed. A possible role of the oxidised form of dithiophosphate collectors, bis[di-alkyl-thiophosphoryl]-disulfane (disulfide), is discussed in terms of a specific self-redox reaction. The second order quadrupolar lineshapes in 65Cu NMR spectra were simulated and the interaction parameters, CQ and hQ, for the bulk dialkyldithiophosphato-copper(I) complexes were obtained.

Jan 1, 2005

Broken Hill South Limited's discovery of phosphate deposits in the northwest of Queensland in 1966 prompted intensive exploration which has proved phosphate rock in excess of 2,000 million tons at ten separate deposits. Systematic exploration for phosphate in Australia was initiated by the Company in 1964. Early in 1966, an investigation of oil wells in the Georgina Basin in the Northern Territory and Queensland revealed widespread anomalous phosphate in early Middle Cambrian Beetle Creek Formation and Thorntonia Lime- stone. Phosphorites recognised in oil wells in the southeastern part of the Basin, Queensland, led to the discovery of the Duchess deposits, Exploration of the Beetle Creek Formation since 1966 has disclosed nine other sizeable deposits north of Duchess around the eastern margin of the Basin. The Lady Annie and the adjoining Lady Jane deposits, by reason of their location, 160 miles south of the Gulf of Carpentaria, are expected to be the first to be brought into production. Beneficiation testing and engineering investigations commenced in 1967. Transport between the deposits and various port sites in the Gulf of Carpentaria has been extensively studied and a slurry pipeline as a means of transport to a deep water island port, is now being investigated.

Jan 1, 1971

By Coates J. R, Firth I. C

The Imperial Smelting Furnace at Cockle Creek, NSW, was constructed in 1961 and is the oldest facility using the Imperial Smelting process in operation. In recent years there have been significant improvements in many areas of the operation, including production, safety, hygiene and environmental performance. Steps taken to achieve these improvements are described. Plans to secure a profitable future while meeting environmental requirements are outlined.

Jan 1, 1993

The techniques originally developed to process digital images of Mars, later gained widespread acceptance when applied to Landsat data: they are now making a significant impact in fields of geology outside remote sensing. The three ingredients of success are seen to be firstly, the perceptual attributes of image displays and the use of colour; secondly, the absolute ability to register data from a variety of sources; and thirdly, the speed of specialist "interactive" digital image display systems. The future lies in further exploiting these attributes through a Geographic Information Systems (GIS) approach to data handling, integration and display.

Jan 1, 1986

By Albano C, Antila A, Flykt B

A method for relating operating variables and dewatering parameters of Thunes disc filters in the LKAB pelletizing plant at Malmberget in Sweden, via empirical mathematical models is described. Near orthogonal experimental design was used, where all independentvariables were allowed to span over their domain of variation and pseudo-randomly distributed among the experiments. The dewatering parameters are dependent on many variables and instead of using a traditional mechanistic model, an empirical model based on multivariate data analysis was chosen. The way of expressing the relation is by regression coefficients obtained from partial least square regression (PLS). Two empirical models were generated. The models were validated using an extra set of 56 experiments. The dewatering parameters were related to the design variables with few experiments, and user-friendly response surface methodology was used to determine the optimal conditions.

Jan 1, 1989

By Lynch P

Oaky Creek Coal Pty Ltd. currently mines high quality coking coal from both underground and open cut operations at its Oaky Creek Mine. Coal is transported by rail to the Dalrymple Bay Coal Terminal south of Mackay and to the Gladstone Coal Terminal. Oaky No.1 Underground Mine, Open Cut and Highwall Mine have concentrated on seams from the German Creek Formation, one of the major productive coal measure formations in the Bowen Basin Coalfields. (Fig. 1) location map.

Jan 1, 1998

This opportunity to present a few thoughts on the question of professional education and training comes at a most appropriate time. In Britain, a great deal of energy is being expended in this, so-called, post-Finniston era, to create a new look for the status of engineers and engineering by the Engineering Council. Naturally, the tune and the tempo are being called by the big institutions which essentially serve the manufacturing industries. However, the Engineering Council in Great Britain also includes the mining and processing institutions such as the Institution of Mining and Metallurgy (IMM) and so there is a chance - if it is taken - for us to contribute to the debate and the determinations that emanate from it. The IMM, of course, caters for the professional status of those engaged in the mining and minerals industries and includes many who do not see themselves as engineers. Nevertheless, the debate is important to these other groups whose livelihood is inextricably bound up with those who are engineers and there are many facets of the engineering policies being shaped that will, I am sure, eventually be enshrined in the requirements for professional status across all the various disciplines in our industry.

Jan 1, 1986

By G K. Robinson, M D. Sinnott

Three-dimensional granular flow models have been run to simulate three types of sample cutters: a cross-stream cutter, a vezin, and a cross-belt cutter. This type of modelling involves solving the equations of motion for large numbers of individual particles as they travel along a conveyor belt and interact with a sample cutter. It allows flows of bulk materials to be visualised and understood. Here we have used spherical particles. These results illustrate some advantages that modelling has compared to physical bias testing: By taking reference samples which are very close to the actual samples, the estimation of bias can be achieve quite precisely with very few runs. (Many Standards about bias testing recommend a minimum of 20 runs, but we have found that five runs generally provide adequate precision.) Potential bias can be divided into two components: the particles which are missed but should have been sampled and the particles which are extra but which should not have been sampled. This more detailed information can provide useful insight. Exactly the same material can be sampled using different sample cutters, thereby avoiding a source of variation that complicates physical testing. Much more detailed visualisation is possible, allowing better understanding of the bulk material flow in various circumstances.

Jan 1, 2005

By Gemmell J. B

Zinc-bearing massive sulphide deposits have been mined in Tasmania since 1900. The current major producers are Hellyer and Rosebery, with total resource tonnages (mined plus reserves) of 16 Mt (million tonnes) and 24.8 Mt respectively. These deposits belong to the class of seafloor volcanic-hosted massive sulphides (VHMS) and are located within the Mt Read Volcanics, a narrow belt of continental margin calcalkaline volcanics of Cambrian age. Compared to other Australian VHMS deposits, and world-wide MVT and Sedex deposits, the Tasmanian examples clearly stand-out due to their high metal grades, averaging over 17 per cent Pb+Zn. The deposits vary in morphology from mound style (Hellyer) to sheet style (Rosebery) with other combinations including stacked lenses (Que River) and disrupted cross-cutting bodies (Hercules). All deposits show the classic VHMS zonation from an Fe-Cu-bearing base to a Zn-Pb-Ba-rich top. Zinc, gold and silver tenor commonly increases toward the stratigraphic top of the deposits. The ores have been deformed during regional metamorphism, resulting in folding, shearing and recrystallisation of sulphide lenses. In addition to the major deposits, a number of small massive sulphide prospects occur throughout the volcanic belt and the potential for the discovery of further large, deeply buried deposits remains high.

Jan 1, 1993

Railway cuttings require the highest care in design and construction, as the pro- bability of failure concept does not allow any risks to be taken with hundreds of lives being dependent on continued stability. The usual geological influences on stability such as bedding dip and faulting are often discus- sed, but other major problems may come from the presence of sheet joints, cross joints differential weathering and seasonal or daily changes of ground water level. The design of rail cuttings has taken little note of the problems imposed by cons- truction methods, and low cost quarrying methods may seriously weaken a designed shape. The presence of berms and drainage ditches is often difficult to achieve as blasting imposes cumulative stresses and jointing on rocks. Contractors face difficulties in bidding extensive rock cuttings as variations in rock properties are often concealed and overshoot- ing the toe of a batter can easily occur. Modern blasting methods offer some solutions, but the best guide to safe successful cuttings is extensive investigation and the continued involvement of engineering geology at the stages of feasibility, design, construction and maintenance. Two case histories show the influence of folding, faulting and construction methods in the case of slope failure and slope stability.

Jan 1, 1979

By Shklyar FP, Babushkin NM, Bokovikov BA, Fedotov PB

A mathematical model for gas flow dynamics and heat and mass transfer processes occuring in the tuyere raceways and in the zone of the final for- mation and heating of pig iron and slag has been developed and simulated on a digital computer. It takes into account the formation and size of the raceway zones, combustion of coke and its substit- utes, oxidation of the metal, radiation from the gases to the raceway boundaries, physical heat losses and the direct reduction of the pig iron elements below the raceway zones. To evaluate the distribution of heat produced by the oxidation of metal between gases and prod- ucts of smelting, the problem of heating the mat- erials in the raceways with the sources of heat in the materials under conditions of intensive gas circulation in the raceways is solved. To determine the amount of heat transferred by radiation from the gas to the boundaries of the raceways, the problem of radiant heat transfer be- tween two grey bodies forming a closed system is solved. Using the structural parameters of the furn- ace, the inlet parameters of the combination blast and exit parameters of the melt, the model permits the calculation of the temperatures of materials entering and leaving the raceways and also the res- idual temperature of the gases, which qualitatively differs from the theoretical combustion temperature. Analysis of the operation of several different blast furnaces has shown that the overall picture of the interaction between gas flow dynamics, mass and heat transfer processes occuring in the race- ways and in the zone of final product formation, obtained with the aid of the model, now permits us to approach from a different position the deter- mination of the limiting factors in furnace operat- ion. It also allows us to explain certain phenom- ena observed in blast furnace practice and to dis- cover new relationships which may be used in analy- sis and control of the smelting process.

Jan 1, 1981

By Schneider CL

The calculation of the liberation spectrum in the product from continuous milling operations is a problem of considerable importance, and it is difficult to solve because the population balance equation must be integrated in two-dimensional space. Complete solutions require a very detailed knowledge of the complex interactions between the fracture patterns and the mineralogical ore texture when brittle particles are subject to impact fracture. Most of the liberation models that have been developed to date apply only to batch comminution processes and under these conditions the liberation problem can be studied in isolation. When the comminution is continuous and forms a unit operation in a flowsheet that includes classification and separation operations, the situation is very different, and then the liberation of the minerals must be described when single particles of known mineralogical composition are fractured. Important industrial examples are conventional milling circuits closed by hydrocyclone and regrind mills in flotation plants. This paper presents an efficient computational algorithm for the calculation of the liberation spectrum produced by continuous milling operations. The algorithm relies heavily on the detailed internal structure of the Andrews-Mika diagram. The modifications that are required to make this diagram apply to practical ore minerals, and the internal structure of this diagram can be established using single-particle fracture on mono-size, mono-grade material but suitable liberation models are essential to interpret the data in terms of the cross transfer coefficients required for the population balance procedure. Models proposed by Leroux (1992) and King (1990) are compared to experimental data.

Jan 1, 1993

By Jankowski P

The Bannockburn gold deposit is located 67 km north-west of Leonora in a poorly exposed part of the Norseman-Wiluna belt of Western Australia. The deposit consists of narrow, complexly shaped orebodies which have presented a challenge to find successful grade control and mining methods. The deposit also presents an opportunity to examine in detail the geology of this part of the Norseman-Wiluna belt.This paper discusses the geology and structure of the Bannockburn gold deposit as well as the grade control and mining systems developed to define the ore and extract it with minimum dilution. We discuss the different techniques employed for grade control in the past and their shortcomings, and the evolution of the present system of doing grade control in cross section from blast hole assays.

Jan 1, 1993

By D Ford

BHP BillitonÆs new rotary iron ore car dumper installation at Finucane Island (Port Hedland) was constructed to increase the total capacity of the port facility from 110 Mtpa to 120 Mtpa and to allow for incremental capacity increases in future. The arrangement of the dumper is similar to other car dumper installations existing on site. To construct the facility, approximately 120 000 m3 of material was excavated in six months, to a total depth of 22 m. The saline water table was nominally 6 m below ground level and the materials excavated varied depending on depth, ranging from sand to mangrove muds. There was a need to retain the sides of the excavation and limit the amount of water from entering the excavated area. This was required to allow excavation to progress and had to be maintained during construction of the permanent concrete and steel facility. The excavation was backfilled progressively as construction progressed. Various retaining wall methods were investigated with the preferred option being sheet piles secured by walers and ground anchors. Detailed electronic models were developed and assessed to complete the final design arrangement. Dewatering bores around the perimeter of the excavation removed the groundwater to intercepted sumps within the site. A strict and methodical program was developed to monitor the integrity of the temporary works and the quality of the groundwater. The works were completed on time despite the following challenges being encountered: availability of resources and equipment, movement of mobile plant on æboggyÆ materials, difficulty driving sheet piles into material at depth, drilling of ground anchors to 32 m, grouting of ground anchors, greater than expected groundwater flows, and the risk of hydrocarbons within the groundwater. The lessons learned from the use of the retention system and, in particular, the associated construction challenges overcome, provide a sound basis for similar work in this buoyant resource market. The conference paper describes the temporary works options investigated, design considerations and processes, construction methodology and challenges encountered, and the monitoring systems developed. Lessons learned are also discussed.

Jan 1, 2007

By De Jong HJ

During the forthcoming reline of No.3 Blast Furnace at the Newcastle Steelworks of the Broken Hill Proprietary Co. Ltd., facilities for the screening and weighing o' coke will be installed. The equipment is needed to optimise the sizing and the quantity of coke immediately prior to it being charged to the furnace. Up till the time the furnace was blown out in November, 1982, coke was charged to the furnace by volume, ie by skip fulls only. This resulted in variation to the ore/coke ratio charged due to bulk density changes and erratic skip filling levels. This in turn affects the heat balance of the furnace and causes fluctuations in hot metal chemistry and temperature. A coke rate penalty has to be paid also. Coke layer thickness in the furnace burden cannot be controlled closely, resulting in loss of control over gas distribution in the furnace. A grizzly type screen was incorporated in the skip loading chute but this ineffective method left a great amount of fines with the coke being charged to the furnace. Furnace permeability was therefore reduced, particularly in the hearth.

Jan 1, 1984

By Tucker G, Clark A, Young M. F, Johnston M

Mount Isa Mines has made a huge commitment to process control in milling. Yet in lead zinc we still failed to achieve a steady operation. Comparisons with manufacturing plants showed the key difference was failure to control plant inputs. Lead

Jan 1, 1998

Direct smelting of copper in a single vessel has long been the extractive metallurgist's dream. Such a process offers the important alvantage. of (i) maximum use of the energy available from oxidizing the sulphur and iron of the concentrate: (ii) restriction of SO2 emissions to a single constant-strength source; (iii) minimum materials handling and (iv) elim-ination of at least one process step. Extensive developmental work was carried out in the 1960's and 1970's to implement such single-step processes. Some of the processes reached the prototype stage and it appeared that copper smelting technology was on the thresthold of a new, efficient, minimum-pollution era. Since that time, however, the forward thrust has slowed and single-step copper smelting is still a process of the future.The paper describes the potential advan-tages of single-step smelting; its history and current status; and the reasons why it has not been adopted industrially. It concludes that the potential benefits of single-step smelting are powerful and that many of the difficulties encountered in the 1970's will be overcome in the 1980's.

Jan 1, 1985

Most orebodies have one or more boundaries which are gradational, where the decision to stop mining is based on an economic cut-off. To maximise profit, this cut-off grade must be chosen correctly. It is necessary to review cut-off grades regularly, as the optimum cut-off grade changes with time, and major changes are hard to implement in a working mine without disruption to production schedules.Whenever a cut-off grade is used, there will be errors in its application caused by errors in the estimation of block grade. These can be minimised by stringent quality control in sampling and by the use of kriging, which attempts to minimise the absolute errors in grade estimation. The kriging method used should produce the most accurate estimates of marginal grade blocks - this will not necessarily be the technique that gives the best overall prediction of head grades.

Jan 1, 1993