Search Documents

By Happ J. V

Factors affecting the rate of arsenic removal from lead bullion during softening processes were studied. Very high rates of removal could be obtained under conditions of intense agitation and ready availability of oxidant. Reaction mechanisms were proposed to explain the sequences observed. Selective removal of arsenic with minimal loss of antimony from bullion was favoured by a low temperature Harris process and oxidizing via a caustic soda medium.

Jan 1, 1987

By Barnett LJ

The Kellogg slag fuming model is extended to apply to the Port Pirie plant which uses recuperative heating of secondary air. Exten- sive investigations of plant operations pro- vide parameters for use with the model, and verification that the resulting model provides simulation which is very close to actual plant performance. The model is used to_deter- mine optimum slag fuming operating conditions, and the results of several other investigations with the model are briefly described.

Jan 1, 1975

By Alvarez A. R, Garcia H. l

A fuzzy expert system, DIME, has been developed, under Matlab v 5.1. to assess the coal and gas outburst risk in underground mining. Expert systems and fuzzy logic are powerful tools to manage information represented by linguistic statements,

Jan 1, 1998

The Tailings Leach Plant at Chingola employs a Leach/Solvent Extraction/Electro- winning process and contains the largest solvent extraction plant in the world, with design liquor flow rates of 55 m3/min. A pilot plant constructed to provide design data also indi- cated areas of uncertain operating and control performance and led to a decision to model the whole circuit to determine the overall dynamic behaviour and basic operating characteristics. Details of the plant flowsheet are given and the basic physical and chemical' equations required for the simulation defined. Each unit operation is considered separately and details of the mathematical models used for their simulation presented.

Jan 1, 1977

By Whitworth NR, Fox MJ, Henley RG

The coal mass flow monitor was developed to measure the instantaneous mass flow rate of pulverised coal to the copper reverberatory furnace at Mount Isa. The instrument was calibrated with an isokinetic coal sampler which was installed immediately downstream from the coal mass flow monitor. Readings from the coal mass flow monitor were used to control the feedrate of coal to the furnace and this helped to stabilise the furnace operation.Coal samples obtained from the isokinetic coal sampler were also sized using a Leeds and Northrup Microtrac analyser. The coal size was critical to reverberatory furnace performance. These developments significantly improved the overall combustion control of the furnace and gains of ten percent were made in the furnace thermal efficiency. Testwork on an auxiliary arch coal burner is also reported.

Jan 1, 1985

The Charters Towers 1:250 000 Gravity Data Set represents a new initiative of the Department of Resource Industries (DRI, formerly Queensland Department of Mines) to provide high quality regional gravity data over areas of the State that have high potential for new mineral discoveries. The Department has adopted a strategy to upgrade geophysical data to complement the ongoing Regional Geological Mapping Program (RGMP) of this Department and in areas where the data would be of most benefit to the mineral exploration industry. Part of this strategy is to ensure that these data are released within 6 months of data collection.The 1989 Charters Towers survey was completed as a joint project with the Bureau of Mineral Resources, Geology and Geophysics (BMR), and is the first regional geophysical data acquisition project undertaken by the DRI. Prior to this survey, the only gravity data in this area dates from the B MR regional surveys carried out between 1960 and 1967.

Jan 1, 1990

By Parker RL

A 250 tons per day ammonia-ammonium carbonate leaching plant is now being operated by Samin Limited, to extract copper from the oxidised ores at the Burra mine. This forms the first stage of a plant, which will eventually have a capacity in excess of 1,000 tons per day. The article reviews the history of the mines at Burra and the metallurgical studies which have been undertaken since the old mines closed in 1917, in an endeavour to recover the copper from the low-grade deposits left by the original miners. The reasons why an ammonia leaching process was selected instead of the conventional flotation or acid leaching methods are discussed. The paper concludes with a detailed description of the plant and the basis on which it was designed.

Jan 1, 1971

By Lean P. J

The present The Zinc ODrporation, Limited and New Broken Hill Consolidated Limited (ZC/NBHC) tailing dam (Site C) is expected to reach its terminal capacity late in 1985. Planning and design of new facilities for disposal of tailing after 1985 which includes new tailing dams (Site D) commenced during 1980. This paper briefly describes planning guidelines and specifications, location considerations, environmental aspects, operating strategy, engineering specifications, envirormental aspects and scheduling of works.

Jan 1, 1983

By Duke J. H

Advanced computer aided geological modelling techniques are now available to the geologist to allow the rapid evaluation of a gold orebody at various stages of its development. The types of grade estimation techniques used change during the various stages as the density of drilling and knowledge of the deposit increases. At the prospect evaluation stage drillhole intercept selection techniques are coupled with preliminary 2D (vein or layer) modelling or 3D block modelling techniques to arrive at a geological resource estimate. At the prefeasibility and feasibility stages more sophisticated 2D and 3D modelling techniques, such as domain controlled grade interpolation with anisotropy, are used along with interactive open pit and underground mine design, to calculate recoverable reserves. At the production stage closely spaced blasthole sample data is modelled quickly and coupled with interactive grade control facilities. Shot volumes, tonnages and grade estimates can be databased to provide reconciliation figures. These modelling techniques are embodied in MINEX-3D, an Australian software system which, with the emergence of the 386-based PC and high resolution (VGA or better) graphics, makes a whole range of advanced geological modelling techniques available to most exploration and mine geologists.

Jan 1, 1989

By Adams DG

At Cook Colliery a combination of main injection of the face coal, and mining into the floor has proved successful for the recovery of faceline falls.The strategy for preventing falls relies upon a conventional method of longwalling. improved geotechnical predictions, and continuous assessment of strata conditions. Different categories of faceline stability are recognised and an operating procedure has been developed for each category.

Jan 1, 1991

By Kerkhoff G, Wood J

The maximum gas emission into underground workings can be predicted by the use of established methods which have world wide recognition. Changes in gas emission and the influence of the gas and geological environments during longwall mining at Pacific Colliery, were found.to be a typical. The relationship between longwall mining and gassy conditions is found to vary from the European experience because of the different mining and geological conditions encountered, and the higher productivity achieved, by single longwall panels in Australia.

Jan 1, 1988

The Directional Drill Monitor (DDM) is an advanced instrument for real time in hole surveying. It was developed by Du Pont (Australia) to suit Australian gassy coal mining conditions. The instrument consists of three units: i. Down hole transmitter ii. Acoustic transducer iii. Data receiver processor unit (i.e. up hole unit). This paper describes the function of each unit in detail and highlights the importance of the DDM in long hole drilling efficiency. Surveying is carried out independent of hole depth. Each survey takes 2-3 minutes to complete, the frequency of surveying to control borehole trajectory is determined by the accuracy required for a particular hole.

Jan 1, 1992

By Yu H, Wan B

40 percent of the coal reserves and 40 percent of the ouput of coal in China is of thick coal seams. The sub-level caving in Yangguan has evolved together with the hydraulic supports, to provide recovery rates today of 80 to 85 percent, waste ratios less than 10 percent and daily outputs exceeding 7,000 tonnes. Matching of rate of shearing bottom coal to caving of top coal is most important to achieve "simultaneous" operations. Spontaneous combustion in the goat, gas, including in the goal, and dust, are particular safety hazards which are combatted with various stringent measures.

Jan 1, 1991

The search for an efficient and economic machine to excavate hard rock continues. Development of the Robbins Mobile Miner commenced in 1983 with the formation of a joint venture between Mount Isa Mines Limited and The Robbins Company. Construction of the machine ensued and preliminary trials to verify the cutting action were undertaken in the USA prior to transportation to and assembly at Mount I-sa where mining commenced in September 1984. Initially, the machine was used to develop the S60 Decline which serves as a combined access and conveyor drive for the Southern 1100 Orebody Ore Handling System.

Jan 1, 1988

By Watson F. G

As an introductory paper of a series on the Melbourne (Australia) Underground Rail Loop extension to the extensive electrified suburban railway system the paper outlines the need for the Loop, legislative background, organizational establishment, engage- ment of consultants, design control, contracts, financial aspects, example of organizational flexibility and certification and transfer of the Loop to the Victorian Railways Board.

Jan 1, 1981

An increase in the silver to gold ratio with increase in depth in the main ore shoot of the Crown- Crescent lode in the Emperor gold mine, Fiji, was found to be due mainly to vertical zoning of gold-silver tellurides. The zoning resulted from

Jan 1, 1980

The provision of electrical power is an important consideration in project develop- ment. The first step to be taken in this area is to assess the power requirements of the project. The alternatives of taking a supply from a power authority or providing local generation can then be considered. This requires additional definition of the prob- able characteristics of the supply. The availability of authority power in Australia is limited by the extent of the state power grids. Recent developments now allow these grids to be extended and their load capacity increased to meet major load increases at less cost than was possible pre- viously. The options for local generation include diesel, gas turbine, steam, hydro, solar and wind, each having its particular performance characteristics and costs. The choice of fuel for diesel, gas turbine, and steam plant likewise involves consideration of a range of factors. The arrangements adopted for a number of development projects illustrate some of the aspects which influence the decisions on power supply.

Jan 1, 1986

The importance of the minerals industry to Australia is briefly reviewed and the professional specialists essential for the industry identified. The average first degree graduation numbers in geoscience, mining engineering, metallurgy/materials and chemical engineering are shown and compared with the postgraduate numbers. Demographic trends in population are reviewed and the implications for the required numbers of trained specialists indicated. Short/medium and long-term possible solutions to potential shortages of trained personnel are canvassed.

Jan 1, 1997

On the 17th November, 1964, a new No., 2 lead blast furnace was blown in at Port Pirie. The furnace departed from previous designs by incorporating a centrally located continuous tapper for both lead bullion and slag. The use of a central tapper permitted a simple and effective layout for the handling of both products. Considerable development was necessary to bring the furnace to its present level of efficiency. Units vital to the continu- ous operation were developed to allow quick replacement, thus ensuring high time efficiency under varied operating and maintenance conditions. The furnace was designed with the following objectives in mind, 1. increased crucible life, 2. elimination of oxygen for slag tapping, 3. higher temperature slag for fuming operations-, 4. less operator skill needed, 5. reduced tapping tool consumption, 6. elimination of settler skull and scrap lead, 7. better control of blast air distributi.nn. And

Jan 1, 1975

The Amacan Copper Project was constructed in the Philippines by a Finnish-Filipino Consortium during the years 1979 - 1982. The project involved a turnkey contract for a mine and a concentrator to process 25 000 tonne per day of porphy- ritic copper ore at a grade of 0.45% Cu. The orebody is located on Mindanao, the southernmost island of the Philippines, in rugged, mountainous terrain approximately 1 000 m above sea level. The adopted design principle was based on an efficient, straightforward installation utilising a minimum number of items of equipment each with high unit capacities. The consortium faced many problems which resulted in lengthy delays in construction and finally led to the client taking over responsibility for the completion of the project. The concentrator was successfully commissioned in July 1982.

Jan 1, 1986