Search Documents

By Kaleta S, McTavish LP, Turner RD

Primary production blasting at Hamers- ley Iron began with seven inch holes at Tom Price in 1966 and has developed since then to large multiple row shots of 381 mm holes at Tom Price and 311 mm at Paraburdoo. Up to 1.3 million tonnes are initiated in a single blast with the average around 300,000 tonnes. Development can be traced through Anfo, AlAnfo, slurries, various boosters, initiation and delay techniques, hole loading and daily operating practices. A standard practice could be developed for the two mines for normal pro- duction blasts; this would not apply to such common variations as low "paddy" shots, pre- splitting, tight corners necessitating single row drilling etc. Because of ground variation three or even four sizes of drill holes may well be economic- al for blasting, even though this would be off set by complications in operation, supervision, store stocking and maintenance, particularly in Drilling.

Jan 1, 1978

By C Yates, S Jobling, Z Y. Yang

The current trend in the UK towards the adoption of retreat longwall mining methods and the associated rapid development of the access drivages have exacerbated the environmental conditions experienced within these workings. There is a recognised need to improve the efficiency of the design and operation of mine ventilation systems in order to maintain an adequate environment and climate within these workings. Any improvement achieved in the quality, quantity and control of the delivered ventilation will assist in the provision of improved gas and dust dilution and climatic control. The paper presents an analysis of the psychrometric data recorded during the execution of a series of comprehensive climatic surveys conducted within two representative deep underground UK coal workings. The surveys were performed across two high production retreat longwall districts within UK Coal Ltd collieries. The surveys employed intrinsically safe psychrometric transducers and digital data-loggers to collect a continuous record of the mine climate over designated weekday production and weekend non-production periods. The transducers and data-logging units are capable of simultaneously measuring and digitally recording changes in the dry bulb temperature and the relative humidity at regular time intervals for extended periods of time.

Jan 1, 2005

By Ueki S

Underground coal gasification (UCG) is a promising process for obtai- ning energy from coal, which is either unmineable with current mining techno- logy or uneconomic to recover, using conventional methods, in the present energy market situation. There are several coal fields, which could become new coal reserves, if the UCG process were successfully applied. In the 1960's Japanese researchers made a number of basic studies and field tests into UCG, although not all of them produced favourable results. This paper reviews Japanese research on UCG. This includs basic studies into coal gasification using a small, tube reactor fed by air and oxygen, and also large scale model stu- dies(reactor size of 8.Om x 2.4m x 1.5 m). Field test results from Akabira colliery in Hokkaido and a feasibility study of power generation using UCG from a coal field in Hokkaido are also Presented.

Jan 1, 1987

By Hughson B

A multi-wire borehole instrumentation system was used to monitor strata movement caused by a retreating longwall face at the Ellalong Colliery, situated in the Lower Hunter Valley in New South Wales, Mechanical anchors were placed at various horizons in the borehole which extended from the surface to the extracted coal seam. The vertical movement of the anchors was monitored during mining. The zone of major disturbance was confined to 13 times the extracted seam thickness above the seam. The average dilation of strata in this zone was 6 per cent. Above the caving zone, the tensile strain was under 2mn/m except at one location, where it was `xmi/m. The subsidence trough under dynamic conditions was flatter than that under stationary conditions. The subsidence also depended upon the extent of strata fragmentation prior to undermining.

Jan 1, 1987

By R Lau

In recently completed road tunnel projects in Queensland, such as the Airport Link and the Clem7 tunnels, there is a smoke duct running along the roof of the carriageways to extract smoke in case of fire. In New South Wales, no road tunnels have a smoke duct. In the Melbourne City Link tunnels, there is a small smoke duct running along the roof. All of the tunnels are safe as claimed by the designers and authorities. However, there is significant cost associated with providing a full size smoke duct compared with no smoke duct. This paper is going to present a comparison of the road tunnel safety with a smoke duct and those without one from a risk perspective. It further discusses the cost-effectiveness of such provisions and whether similar levels of safety could be achieved without a smoke duct.CITATION:Lau, R, 2014. Smoke duct or no smoke duct for road tunnels, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 83–86 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By A J. Moore

To control the airblast from blasting to regulatory limits at environmentally sensitive sites near the Collinsville Coal Mining Operations, it has been necessary for Thiess Mining to incorporate a wavefront reinforcement analysis model in the predictive environmental airblast design. Controlling airblast from cast blasting 70 m high faces with 2000-3000 kg of explosives per hole within 700 m of houses presents a considerable challenge to the blasting personnel. This paper describes the model used and summarises the results of an investigation designed to quantify the increase in airblast indicated by wavefront reinforcement diagrams to further calibrate the model for future prediction.

Jan 1, 2004

An examination has been made of the rate and extent of removal of carbon from scrap metal charges when the melt is exposed to atmospheres which are reducing or oxidising with respect to FeO at unit activity. The mechanisms of decarburisation of molten Fe-C-S- P-Mn-Si alloys with H2/CO/H20/C02 gas mixtures with controlled compositions at high or low concentrations of carbon in the melt in the presence and in the absence of sponge iron, in both slag free melts and in the presence of various slag forming additives are discussed. A significant quantity of carbon can be removed from the metal during the melting stage and under optimum conditions, a high percentage of metal recovery and low carbon can be obtained after exposure of melt to the above gas mixture with controlled compositions. The presence of ferrous oxide provided by poorly reduced ore in the charge and the use of controlled atmospheres facilitated the removal of carbon to very low level during the melting period.

Jan 1, 1984

By G J. Corbett

Magmatic-related low sulfidation hydrothermal ore systems at plate margins exhibit distinct spatial and temporal zonations which can be used to aid mineral exploration and development. Low sulphidation systems at all crustal levels exhibit the same paragenetic sequence of events: early breccia formation, followed by quartz - secondary feldspar sericite/illite veining, then mineralisation, and final argillic overprint. This sequence of events is interpreted to reflect the initial emplacement of melts at high crustal levels, and the progressive cooling of that melt and release of magmatic constituents into a circulating hydrothermal system.   Low sulphidation systems in the south-west Pacific region exhibit a vertical zonation in deposit types: from porphyry copper-gold at deep levels, quartz-sulfide-gold at mesothermal to deep epithermal levels, carbonate-base metal gold at mainly epithermal levels, and epithermal quartz silver-gold at shallow levels. It is interpreted that the characteristics of each of these styles of deposits is produced by mixing with circulating waters of different physio-chemical compositions.

Jan 1, 1995

The major slime forming minerals in coal seams are generally montmorillonite, illite and kaolinite, and due to the consistant trend to full seam mechanisation in New South Wales and Queensland these minerals remain in the feed to a coal preparation plant. After coming into contact with water their size degradation is very rapid, and therefore they mostly report to the fine coal cleaning section of the plant. Froth flotation, being the most effective method of beneficiating fine coal, is widely practised in these two major coal producing states of Australia. Plant experience and laboratory tests suggest that the presence of these slimes in the flotation circuit depresses the flotation of fine coal. Although the deleterious effects of slimes on the flotation behaviour of minerals is well known, the mode of their adsorption at the mineral surface has been a subject of controversy for some time. In this paper, on the basis of the surface properties of slime forming minerals and coal, a model has been put forward to explain the adsorption of slimes at the coal surface. The degree of slime coating has been examined by scanning electron microscopy. Laboratory tests have revealed that with the appropriate use of polyvalent phosphate electrolytes these slimes can be liberated from the coal surface. Just attrition and desliming are not enough to ensure complete liberation of slimes. Coal, after treatment with these electrolytes and then deslimed, floats readily with a common frother, such as MIBC. Modifications in the conventional flotation circuits have been suggested to ensure an efficient flotation of fine coal.

Jan 1, 1978

Results are presented of the investigation of gas dynamics of the blast furnace process obtained on laboratory models and operating furnaces. Gas residence times were measured using a helium tracer technique developed for the purpose. Residence times were determined in furnaces of 1007 m3 and 1719 m3 and results used in the calculation of the burden parameters and to estimate the distribution of the gas flow along the furnace radius. The effect of tuyere injection of coal dust on gas distribution was also investigated and the advantage of continuous injection compared with intermittent injection is noted. The unevenness of gas distribution across the furnace area is found to correlate well with differences in the size analysis of the iron-bearing component of the burden. The mixing of the gas streams between the neighbouring raceways was studied. It is shown that in the central region of the furnace gases from every tuyere are mixed together, whilst in the peripheral regions mixing is more localised and includes only the sections consisting of five adjacent tuyeres. A solution is proposed to the problem of a theoretical evaluation of the critical gas velocity. A simple relationship between the Reynolds and the Archimedes numbers was obtained from which, after substitution of the burden size data and the gas parameters, it is -possible to evaluate the critical gas velocity. Conclusions include information relating to the optimisation of the gas distribution and views on reducing gas injection at elevated furnace levels.

Jan 1, 1975

Warkworth Mining has been successfully operating a large open cut coal mining operation in the Hunter Valley of NSW since 1981.The mine is a complexmulti seam operation and utalises both truck and shovel and draglinetechniques. Warkworth Coal Sales Ltd markets approximately 10 different coal types.Since the mines inceptionthe development of mine scheduling and planning has been an ongoing programme. Resource recovery and coal utalisation have been the driving factors with this development as we strive to achieve maximum revenue for the investment dollar.The principal aim of this paper is to discuss the scheduling methodology as it is utilised todayhighlighting the interaction in the development of the final coal products schedule.Whilst the system is notperfect it has evolved and operated successfully in these difficult economic times and offers a practical and achievable approach to resource optimisation.

Jan 1, 1992

By Wilson PH

A research programme sponsored through the Australian Mineral Industries Research Association investigated two aspects of mine aerodynamics on model scale. These were aero- dynamic losses in (a) shaft/airway intersections and (b) losses created by mine cages moving in a combined haulage/ventilation shaft. The shaft/airway intersections studied included base and intermediate levels for both upcast and downcast. shafts, with one to four rectangular airways intersecting a circular shaft. Changes in intersection geometry were limited to the installation of 45¦ conical brow cutoffs of varying size and the addition of simple flow control devices. The relative air- flows between the airways and the downstream shaft were varied over a range employed in Australian mining practice. In general, experiments revealed that a small brow cutoff was significantly better than none at all, and a simple device such as a cone can reduce losses and improve flow stability at an intersection. The mine cage studies determined the effect on aerodynamic loss of cage area blockage, height/length ratio, openings in cage walls and surface roughness due to external structural members. The results show that in a combined haul- age/ventilation shaft, when the relative air

Jan 1, 1978

By S Planeta

The use of explosives in underground mining has its drawbacks, particularly in the case of thin or narrow vein type deposits. Due to that, there is a need to develop more discriminative and safe rock-breaking technologies. Mechanical rock splitting seems to be one of the most promising avenues in this respect. This paper describes briefly principles and features of radial-axial splitters. It reviews a feasibility study done to evaluate a potential of this technology in selective mining. It was intended to compare productivity and cost of ædrill-splitÆ mining with conventional cut-and-fill method. Hypotheses and assumptions adopted, methodology used and the obtained results are presented and discussed. The study has confirmed an interesting potential of radial-axial splitters in mining thin and narrow vein deposits. In conclusion, it is stressed however, that it will take more R&D work to corroborate the results obtained. Some suggestions concerning future research in this field are also given.

Jan 1, 2003

Efforts to stabilize international markets in commodities have gradually intensified during the course of this century in keeping with the grow- ing complexity and interdependence of the world economy and the increasing involvement of government in economic activity. Successive Australian Governments have con- sistently supported the concept of commodity agreements and arrangements in an effort to lessen short term fluctuations in price and to moderate the boom/bust conditions which tend to charac- terize production and trade in many commodities. The objective is to stabilize price at a level which equates supply and demand over the life of the arrangement. Such action involves a degree of market inter- vention and government involvement in the inter- national trade in the commodity concerned; the acceptability and desire to foster such arrange- ments varies from country to country depending upon attitudes to market intervention and man- agement. However attitudes, even among those opposing commodity agreements, have under- gone a major reversal in this century. Before the first world war, such intervention as existed almost entirely involved the physical producers. There was almost no government involvement and at that level most regarded commodity agree- ments as neither desirable nor practical. However government regulation of such activities as pro- duction and marketing of food during World War I, coupled with post-war shortages, followed by overproduction and the crash in prices during the Great Depression, stimulated producer gov- ernment interest in commodity market regulation. Consumer governments took a little longer and with a few exceptions, it was not until the post World War II period, that the fear of shortages of basic commodities brought some consumer countries to accept the concept.

Jan 1, 1978

By Wagland D. G, Guo H

The Mt Whaleback orebody is in a complex geological regime. A good understanding of geological structure is essential during the design and implementation stages. The amount of information on the rock-mass condition available at the design stage is considerably limited. It is essential to validate the rock-mass properties used in the design during implementation. It is important to achieve integrity of the final pit wall during development and to maintain the integrity until the end of its designed life for safe and economical extraction of ore. The original geological model is updated by way of on-going detailed geological face mapping. Original design is reassessed and is modified based on any significant variations to the previously evaluated geotechnical conditions. Information gathered during design implementation provide tools for effective management of the pit walls. Controlled blasting techniques are employed in the final limits blasting. Presplit blasting is used in most limits blasts. Presplit helps to maintain the integrity of the wall by venting excessive gases from the limits blast. This helps to reduce bedding dilation by gas penetration. Also, it helps to define the design batter for the operators for final batter trimming. Pyritic shale needs special attention during blasting due to its reacting nature. Cablebolting is applied in selective areas to secure small-scale potential instabilities. During the development phase, pit wall monitoring instruments are installed. These instruments are used to monitor the performance of the wall during and after excavation of the slope.

Jan 1, 1995

By G Giles

One of the main tools used by mining operations to mitigate the risk of rock burst is the installation of a so-called ædynamic resistantÆ support system. Such systems are designed to absorb the impact of shockwaves created by mine-induced seismic events. Dynamic support must be strong and capable of sustaining high loads and, at the same time, they have to be flexible and accommodate large deformation. A dynamic support system is therefore a system capable of absorbing a high quantity of energy. Ground support systems are composed of rock reinforcement (rock bolts or cable bolts) and surface support (mesh or shotcrete). In terms of surface support, fibre-reinforced shotcrete is increasingly seen as the industry preferred solution when difficult ground conditions are experienced, including areas of high seismic hazard. A thick layer of shotcrete is certainly strong but it is by no means flexible. Normal weld-mesh has some flexibility, but it is not very strong. The Australian Centre for Geomechanics (ACG), in collaboration with Onesteel Reinforcing Pty Ltd, is currently working on a new high-energy absorption mesh that combines strength and flexibility. The new mesh can be installed with a jumbo, in a similar way as the widely used sheet of weld-mesh. This paper describes the development of this new mesh system.

Jan 1, 2008

Edie Creek is located in the Morobe Goldfield about 17km by road from Wau in the Morobe Province of Papua New Guinea (PNG). Four distinct periods of mining development have occurred since discovery of rich alluvials in 1926. During the two years following discovery, individual expat-riate miners with gangs of native labourers mining rich alluvial gravels dominated the field. After the discov-ery of hardrock mineralisation in 1927, companies accumulated leases and devel-oped extensive underground mines and mechanical processing plants at Day Dawn Mine and Edie Creek/Karuka Mine between 1929 and 1942. After the Second World War, the underground operations were not re-opened, and mining activ-ities mostly concentrated on working alluvial and eluvial deposits. From 1962 onwards, Papua New Guinean miners became increasing producers as company activities declined. In 1990, Edie Creek Mining Company Pty Limited, a joint venture company involving Wau landowner groups commenced operations on New Guinea Goldfield's leases. It currently mines by open pit methods, rich quartz stringers and is invest-igating the open pitting of the Edie Creek/Karuka underground workings.This paper describes the mining and processing techniques employed during the various phases of develop-ment at Edie Creek in the past 70 years. The problems and hardships of operating on a new and remote goldfield are outlined.Abstract

Jan 1, 1994

By Perring CS, Barnes SJ

The nickel exploration boom of the late-1960s and early-1970s led to the discovery of numerous komatiite-hosted nickel sulphide deposits, associated with variably serpentinised bodies of olivine-rich cumulates. Subsequent research has shown the importance of volcanological processes to understanding the genesis of these deposits. Crucial developments have come through consideration of the fluid dynamics of magmas and magma-crystal mixtures, through observation of the dynamics and geometry of modern day basaltic lava flows, through application of theory and experimentation on the kinetics of crystal growth from magmas, and most importantly from extensive detailed field mapping of komatiitic sequences in the Yilgarn Block and elsewhere. From these studies has emerged a new integrated view of the volcanological setting of komatiite-hosted deposits, and a recognition that a complete continuum of deposit types exists. Nevertheless, komatiite associated magmatic nickel deposits generally fall into two overall types based on the nature of the sulphide ore. In the first type the bulk of the ore is either massive Fe-Ni-Cu sulphide or a variable mixture of massive sulphide and an ore characterised by olivine crystals in a continuous matrix of sulphide occupying between 30 and 75 per cent by volume of the rock (called Matrix Ore). Nickel grades of massive sulphide ore range from 2 - 20 wt% and those of the matrix ore generally fall in the range 1 - 5 wt% (average 2.5 wt%) Ni/Cu ratios of the sulphide fraction are generally >10.

Jan 1, 1996

Historically BHP Billiton Alliance Coal Operations Pty Ltd (BMA) have generated resource models from widely spaced data points (drill holes). The accuracy of these models has been influenced by the degree of local structural disturbance of the coal seams and by the choice of interpolators used in the modelling process. In some circumstances unacceptable vertical errors of up to 10 m have been observed whilst mining. New terrestrial photogrammetry or laser imaging technology now allow the 150 or so kilometres of exposed highwalls in BMA to be rapidly, accurately and safely mapped and the three-dimensional images economically incorporated into resource models, reconciliation grade control models, drill and blast designs and for pit stability analysis.

Jan 1, 2005

By Mills KW

Coal mine pillar design formulae available to mine planners are typically based on relationships determined for specific site conditions. Application of these methods is difficult when other factors, relating to mining or geological conditions, not specifically addressed in these relationships are encountered. A review of pillar design methods, coal strength properties and relevant field monitoring of pillar behaviour has shown pillar strength and deformational characteristics are extremely sensitive to in situ behaviour of the rock and other material components that make up the coal pillar system. A method has been developed that has been found to provide excellent correlation between existing field data using the strength and deformational characteristics of materials determined in selected laboratory tests. This method is based on definition of the loading conditions, accurate modelling of the strength, confining conditions and deformation occuring in the roof, floor and coal seam and definition of the in situ strength of coal based on underground monitoring of appropriately sized coal pillar. The design method is considered to provide an accurate and rigorous pillar design method that will give mine planners a more rational mine design capability which is based on the mine geometry and geological setting of the operation. It is envisaged that availability of such a method will allow significant optimisation of pillar layouts and more closely define the geological and mining issues that relate to pillar design optimisation.

Jan 1, 1992