Search Documents

By T Ueda an, T Sasaoka, A Yabuki, H Shimada

The basic concept of auger mining is to extract coal beyond the economic limits of surface mining technology by drilling holes of an appropriate diameter size into the exposed seam of the highwall as deep as is technically, economically and operationally feasible. This method of mining is used at the final highwall of typical surface mining operations. This paper describes the auger mining systems and discusses the methods to increase the coal recovery in auger mining from a field trial in Australia.

Jan 1, 2003

The Writer's knowledge of this region began in 1912, while he was with the Geological Survey of South Australia, and, investigated the principles governing the occurrence of fresh and saline ground waters in the area then being opened for closer settlement by the railways under construction from Port Lincoln.These field investigatons for water were extensive rather than intensive, but other examinations covered certain mineral aspects. The Writer also has' had the benefit in the preparation of this paper, of later work done by others, as well as of the monumental earlier work in South Australia by the late H. Y. L. Brown.AREAThe area dealt with, approximately 21,000 square miles, lies to the south of the latitude of Port Augusta.TOPOGRAPHYAs a whole the region is one of low relief, but the Olinthus Range, west of Cowell and north of Cleve, reaches an elevation of 2,000ft., while there is als0 a high area west of Port Lincoln and Tumby Bay. At the north end of the region the Gawler Ranges are formed by the dissection of a thick sheet of felspar porphyry extending over two degrees of longitude, by a width of 20 to 70 miles, with fairly uniform maximum elevations of the undissected portions of the order of 1,000 ft. above sea level. South of the Gawler Ranges are many isolated ridges up to 1,000ft. in height, generally sedimentary and trend...

Jan 1, 1951

By A Singleton, J Busfield

World coal producers have been under constant pressure in recent years because of falling export prices arising from oversupply and the Asian slowdown. This has resulted in a dynamic market place, a sharpening of focus on bottom line costs and some rationalisation of participants. Productivity has increased dramatically as many inefficiencies, typical of the coal industry, have been eroded through workplace reform. This is true for the both open cut and underground sectors of the industry. At the same time, the technology of underground mining is undergoing dynamic change. Mine operators are implementing better exploration and planning tools and are also starting to make gains against chronically low equipment availability and utilisation. æStep-changeÆ improvements in output are imminent. As the statutory environment shifts to a æduty of careÆ regime, it is hoped that mine safety performance will improve, particularly with regard to fatalities. The focus of the paper is on the Australian coal sector, although references to international benchmarks are made. Despite environmental threats to the future of coal, it is concluded that the next ten years will see impressive performance results from underground coal mines which will assist coal to maintain its position as the preferred fuel of lowest cost.

Jan 1, 2000

By S C. Sc, J Young, N Belluz, D Nicholas

The heavy sulfide zone (HSZ) of the Grasberg deposit has the geometry of a funnel and is located at the contact of the mineralised intrusive and the relatively barren sedimentary rock types. The geometry and the rock properties associated with the HSZ plays a significant role in pushback design and sequencing. Most of the HSZ has relatively low strengths which must be considered in slope design and management. This paper presents the open pit mine geotechnical and planning design considerations associated with the HSZ.

Jan 1, 2007

By G Gibson

Realising that current roadway development performance levels were unlikely to sustain new generation high-capacity (15 Mt/a) longwall mines then being planned, the Australian Coal Association Research Program (ACARP) established a Roadway Development Task Group (RDTG) in 2005 to develop a research strategy targeted at improving roadway development performance in Australian longwall mines. The initial phase of the project identified a number of factors that differentiated best practice mines from others, and proposed a multi-faceted research strategy encompassing both short- and long-term research initiatives, including:conducting regular benchmarking studies across the industry to identify factors contributing to improved performance and to monitor performance trends,conducting regular industry roadway development operatorsÆ workshops to facilitate the transfer of successful roadway development improvement initiatives throughout the industry and facilitate networking between development practitioners,development of alternative skin reinforcement and containment measures that would eliminate the use of steel mesh and enable face support systems to be fully automated,development of automated bolting and mesh handling systems that would enable operators to be removed from the immediate face area,development of a body of knowledge of industry roadway development practice,development of a web-based information management system to capture and transfer emerging developments in roadway development practice and technology,reviewing the Australian civil tunnelling and underground metalliferous mining sectors to identify practices and technologies that could potentially be utilised to improve roadway development performance, anddeveloping a new generation high-capacity mining system capable of +10 metres per operating hour for 20 or more hours per day (CM2010). The paper reports on the progress of the above initiatives and outlines strategies to continue the pursuit for improved roadway development performance.

Jan 1, 2008

George Fisher Mine, near Mount Isa in northwest Queensland, has been producing Pb-Zn-Ag ore since the late 1980s. It consists of two separate underground deposits, George Fisher South and George Fisher North. These two deposits are drilled and modelled separately but are crushed and hoisted as a single stream. The Pb-Zn concentrator in Mount Isa processes ore from George Fisher Mine and Black Star Open Cut, with production also from the Isa Lead Mine until January 2006. This paper outlines the steps involved in setting up a robust reconciliation system for George Fisher Mine, in conjunction with requirements of the Pb-Zn concentrator, Black Star Open Cut Mine and the Mount Isa Lead Mine. Good quality input data and commitment to training have contributed to establishing a robust and effective reconciliation system. Reconciliation data has highlighted several other continuous improvement opportunities.

Jan 1, 2006

The limitations of the conventional practices, and their effects, in prospecting for and in the evaluation of alluvial gold deposits are briefly reviewed. Geophysical prospecting methods have demonstrated their complementary role in the delineation of deposits by reducing the number of boreholes which are primarily of a 'probing' type. Larger diameter boreholes, although more expensive on a linear basis, are much cheaper on a volume recovered basis. The need to have sufficient volume as well as number of samples is stressed. Classical statistical methods are not appropriate for such deposits as there is sufficient structure, or spatial correlation, to require the application of geostatistics. Quite reliable semi-variograms, but not in all cases, of the spherical scheme have been obtained. Subsequent kriging has, to date, been confined to unworked deposits: retrospective estimates to compare to production have not therefore been produced. However, the technique shows promise but indicates a considerably greater borehole density (of the conventional diameter) may be necessary to produce confident estimates. Used in conjunction with larger diameter boreholes, a lesser borehole density may be sufficient, through radical reductions of the sampling error.

Jan 1, 1977

By Tapp B. A

To date, few studies have been made regarding the energy requirements of the Australian mining and mineral processing industries. This paper indicates that these industries use a substantial proportion of the total Australian energy input (32.7% in 1971-72 and 36.10% in 1974-75). With the growth orientation of these industries, this input is likely to increase. Data shows that mining energy requirementE varied from 4.22% (of total Australian energy requirements) in 1971-72 to 4.16% in 1974-75. Energy requirements for the total mineral processing industries increased from 28.49% to 31.93% for the same period. The total estimated primary energy input varied from 22.56% to 25.2%, whilst indirect energy use, in the form of electricity increased from 10.16% to 10.66%; in the same period. Analysis of primary energy input data within the processing industries (1973/4) showed that the Iron and Steel Industry consumed 15.03% of the Australian total consumption, Non-Ferrous metals, 5.43%, Cement, 1.64%, and Refractories, 1.59%. In toto this represented 24.57% of the total

Jan 1, 1979

The effects of changes in sintering bed height, coke fuel, suction and basicity on sinter productivity, physical strength and mineralogy were determined. It was found that, for a given iron ore, there is a narrow -coke range which maximises sinter strength, irrespective of bed height (in the range 300 to 500 mm) or basicity (in the range 1.2 to 2.2). Increases in bed height, at a constant coke level, improved the physical strength of the sinter. Productivity increases were obtained by increasing the sintering suction but, at coke levels other than the optimum, these *ere somewhat offset by the decrease in sinter physical strength. At basicities higher than 1.2 (i.e. 1.6, 1.8 and 2.2) there was a narrowing of'the size range of product sinter, with a decrease in the percentage of top size material, and a decrease in the amount of fines produced. Changes in coke, bed height and basicity exert major effects on sinter mineralogy, while the Nagoya index was mainly influenced by cote and bed height Changes.

Jan 1, 1975

By Dunstan N, Valentine C

Gas power was first used on the Sons of Gwalia mine in January 1911, when a twin-cylinder Crossley engine of 167 hp was installed to belt-drive a 112 kw 550-volt ac generator. This engine was connected with a No 8 Crossley up-draught suction gas producer, using mulga charcoal as fuel.A second Crossley engine, of 400 hp direct-coupled to a 550-volt ac generator, was installed in 1912, and operated by a down-draught wood producer.This was followed by a large Kynoch twin tandem four-cylinder engine, rated at 660 hp, sea level, with a rope drive to the crushing and treatment sections of the plant.These engines operated until January 1921, when the plant and power house were destroyed by fire. After the fire, both Kynoch and second Crossley engines were salvaged and reconditioned and they continued to give useful service for some years.

Jan 1, 1932

Although laterite ores already provide a significant proportion of the world's nickel and cobalt production it is anticipated that they will surpass sulphide ores as a source of nickel in the next century. The most recent period of greenfield nickel project construction was during the 1970s when it was notable that all of the eight new plants were based on treating laterite ores. This was because of the relatively large selection of available high grade laterite ore deposits amenable to cheap open cast mining and a paucity of high grade sulphide ore prospect alternatives. Of the three processing options for treating laterite ores: 1. smelting for the lower horizon saprolite ore, 2. ammonia; and 3. acid leach for the upper horizon limonite ore, smelting currently accounts for about 80 per cent of nickel production. In the future, as saprolite ore grades decline because of relatively high exploitation rates, the incentive to process the large untapped reserves of limonite ore will increase. The high cobalt content of limonite ore also makes it ideally suited to processing by a hydrometallurgical rather than smelting route. With only two exceptions, all saprolite smelting operations have a Class 2 nickel end product (largely ferronickel) and do not produce a cobalt by-product. As a result of technological advances, the modified ammonia leach process for limonite and transition ore as undertaken at Yabulu, now allows the production of pure nickel metal as a Class 1 product, along with significant tonnages of cobalt by-product. The mixed Ni-Co sulphide intermediate product of the pressure acid leach processing of limonite ore at Mon is converted to Class 1 nickel and cobalt metal at Fort Saskatchewan, Canada.

Jan 1, 1996

Pulverised coal firing was pioneered in the cement industry prior to the turn of the century. Ash from the coal is absorbed into the mix in the kiln and replaces secondary materials. With high purity limestone coal with high ash content can be used. Fuel cost is a major part of the total manufacturing cost. Cement plants are thus quick to respond to fuel price changes and will use low grade fuels if there is a price advantage. Combustion conditions in a cement kiln differ markedly from a boiler. Flame length is determined by air/fuel mixing but because of fixed secondary air conditions this depends on primary air momentum. Volatile content has some effect on flame length but this can be offset by coal fineness. Much of the heat for cement production is for limestone calcination which is a low grade energy requirement. By allowing long residence time in separate direct fired vessels which then feed the high temperature kiln the energy of materials such as oil shale, tyres and lump lignite can be utilised.

Jan 1, 1987

By K McNabb, M H. Turner, P A. Jenkin

Mining of the Agnew nickel deposit commenced in 1970 using a variety of underground mining methods, though with mixed success due to the difficult ground conditions. WMC Resources Ltd acquired the operation in 1989, and commenced nickel production with an open pit. In 1995 all production reverted to the rejuvenated underground mine, using exclusively SLC (sublevel caving) methods. Currently the mine produces 1.4 Mt per annum, at an average grade of 1.74 per cent Ni. Underground mining of the Perseverance orebody has always presented significant challenges due to the difficult ground conditions in the weak and altered ultramafic rocks. The range of problems include areas of swelling minerals, intense and extremely weak shear zones, relatively high in situ stress, and in other areas very brittle rocks. Under these conditions rock mechanics input has been and remains a critical element of the mining strategy. Severe ground behaviour difficulties down to a depth of 500 m below surface prompted a review of the mining strategy for the large disseminated nickel orebody, including evaluation of alternative mining methods. However, sublevel caving was ultimately selected as the preferred method, and a re-design of the SLC cross-cut layout followed. A selection of rock mechanics investigations of interest are described, including complex virgin stress measurements, detailed ground behaviour monitoring, and the use of non-linear stress analyses to re-design the mine layout. Subsequent ground behaviour, support design and production scheduling are also described.

Jan 1, 2000

To the south and west of Broken Hill lies the Thackaringa silver-lead district, about 25 miles, and is the locality really of the first silver find in the country long before Broken Hill, the geological fomations of which it much resembles. The Iocks and their structure are identical, except that in this area they are  more irregularly foliated and apparently much more faulted and expose in places quick successions of complete anticlines and synclines, even in a single lease. Saddles of ore respectively are found coinciding with the flexures of the rock but many minor veins otherwise and branches exist and make connections which render the whole a mining problem. It follows then that the surface.of the ground after some denudation in dotted with croppings of all the series, and in such a confusing way that the actual strike of a vein may be even confounded with the dip and readily mistaken for it at a few places. The main character of the outcrops are those usual in the district consisting almost wholly of argentiferous and silicious ironstone, sometimes gossan, which at a depth in a few feet changes to a gangue of very silicious carbonate of iron (crystallised), which occurrence is uniform through this district.The exploration of the lodes has not been extensive as it has not been well understood. Shallow shafts and drives have comprised nearly all the mining at present, which is evident on first sight by the numerous shafts and small excavations dotted 'about, as in an alluvial field. The depth of exploration underground in one place had gone several hundreds of feet, never more than 150 feet vertical from the surface in depth and irregular. The undulations of the most continuous work in this direction is such that it presents at different places successively either a tunnel, shaft, underlay winze, level, or Tise, and is on ore all the time, and where the rocks are faulted (which occurs as much as 30 feet and more) these changes are very abrupt, but for working on are suitably connected by the management.

By S R. Grano, M Vera

This paper deals with two separate case studies investigating the froth phase performance and characterisation of two industrial rougher/ scavenger flotation circuits. Froth phase performance was quantified using a mass balance approach to estimate froth zone recovery. Measured characteristics of the froth phase included frother solution concentration determined by gas chromatography, and the time taken for an equilibrium froth sample to decay to one-half of its original froth height. The latter measurement is referred to as the æfroth half-lifeÆ and is strongly linked to froth stability. Special methods and techniques developed to preserve frother in solution and to measure froth half-life are briefly described. The frother type in the first case study was a mixture of straight and branched alcohols, whilst the frother type in the second case study was a mixture of alcohols, aldehydes and triethoxybutane. The first case study focussed on a flotation circuit treating a low-grade ore containing only a small fraction of floatable copper sulfide minerals, while the second case study focussed on a flotation circuit treating a higher grade complex sulfide ore containing significant quantities of chalcopyrite, galena, sphalerite and pyrite. It was found that froth zone recovery of valuable mineral generally decreased down-the-bank of the two industrial rougher/scavenger circuits. Moreover, decreases in froth zone recovery significantly limit the overall cell recovery of valuable mineral achievable from the plant scavenger cells. However, the decrease in froth zone recovery could not be linked to the removal of frother from the pulp solution to the concentrate product in the preceding rougher flotation stages. Measurements of residual frother in solution suggested that, approximately, only five to ten per cent of the added frother was removed into the rougher/scavenger concentrate, with the remainder appearing in the scavenger tailings. This finding suggested there was apparently adequate frother in solution in the scavenger stages.

Jan 1, 2005

This paper describes an ongoing study into the management systems developed by mining operations in Papua New Guinea to address particular public health issues in the workforce (primarily communicable and lifestyle diseases). The first stage of the study involves the analysis of the site health and safety management system documentation of three major mining operations in Papua New Guinea, producing a descriptive summary of each system. In the second stage of the study these summary descriptions are evaluated using a maturity model constructed through a detailed review of literature. Experience with the evaluation process is then used to refine the maturity model. The analysis performed in the study is used to develop a process for creating a maturity model for mine site health risk management based on a theoretical risk management framework, and refining it through empirical evaluations of the actual systems in place on site. Companies can use maturity models as a guide to organisational improvement, which in the context of the study will assist the operations in developing their systems for the management of health both in their workforce and in local communities.

Jan 1, 2007

By M G. Aylmore

Thiosulphate is an attractive alternative reagent to cyanide for processing gold ores. It is relatively cheap and non-toxic, forms relatively strong gold and silver complexes, and readily leaches gold ores in ammoniacal solutions, catalysed by Cu(II). It is particularly suited to carbonaceous ores where the recovery of gold by cyanide is poor. However research over the past 20 years has identified a number of issues and impediments that must be understood or overcome before an overall process can be demonstrated as practical and economic for typical oxidised gold ores. This paper reviews our current understanding of thiosulphate chemistry and mechanism of gold dissolution, and discusses the stability of thiosulphate and polythionates. It then reviews the results of leaching various gold ores that have been reported in the literature, discusses gold recovery options, and considers environmental and toxicity issues. Some of the issues that require further research include decreasing the oxidation of thiosulphate by Cu(II) or other oxidants, increasing the extraction of gold compared to cyanide, and understanding the variation in gold recovery between ores. More work is also required to minimise the effect of polythionates on gold recovery using resins or alternative absorbents, to improve the elution of copper and gold from resins, and to recycle or minimise the concentration of reagents.

Jan 1, 2002

Oxy-ACETYLENE system of welding and cutting is at present practised in two forms, which may be described as the high and lowpressure systems. In the high-pressure system the two gases, oxygen and acetylene, are delivered. to the blow-pipe under pressure from properly constructed trade cylinders. Oxygen cylinders are in two sizes, each containing 100 and 200 cub. ft. of gas respectively. These cylinders are charged to a pressure of 120 atmospheres, or 1800 lb. per sq. in. approximately. The acetylene cylinders are made in one size as far as the writer knows, and contain 200 cub. ft. of acetylene gas at a pressure of 10 atmospheres. Each cylinder is provided with a valve and connection for attaching a regulator to "break down" the high pressure in the cylinders to the necessary low working pressure of the blow-pipes, and to deliver the two gases at a constant pressure irrespective of the variable pressures in the cylinders. These regulators can be adjusted down to as low as 1 lb. and are provided with two pressure gaugesone reading the contents of the cylinder in atmospheres, and the other the working pressure in lb. per sq. in. The high-pressure, or "two cylinder" system is compact and can readily be transported from place to place in the works. For this purpose the two cylinders are mounted on an easy-running 4-wheeled truck, which the operator and assistant find no difficulty in manipulating. In the low-pressure system the two gases are delivered to the blow-pipe, one from the oxygen cylinder and the other from the acetylene gas generating plant, which consists of the following:Generating cylinder, half filled with water, into which the cathoide is plunged. The generated gas is passed through a filter to the gasometer, then through a water washer on to the hydraullic seal...

Jan 1, 1922

The intent of this address is to look forward into the 21st Century and present certain thoughts as to how underground coal mining might be conducted. The views in this talk are based principally on the author's experience with mining practices in the United States. It may be difficult to accept, but the 21st Century is a mere 12 years away. What new techniques will be available? To develop an understanding of the way in which technology has been and could be changing, a two- stage analysis is made of mining technology for U.S. Coal. The first phase covers the period 1975 to the present, while the second includes 1960 to 1975. This historical perspective includes a view of underground production by mining methods, considerations of labour productivity, and a review of accident and fatality rates. Several topics are important features of this historical analysis. Among the most significant are: (1) the introduction of Ion-wall mining technology into U.S. underground coal mines, (2) the use of computers to assist in mine planning and design activities, (3) major efforts to improve health and safety performance, with emphasis on underground dust control, and (4) improvements in mining equipment with an eye towards increased reliability and up-time performance. Based on that historical perspective, projections are made in three increments. The first being immediately at the turn of the century, the second being a dozen or so years beyond that, and the third being at the quarter point of the 21st Century.

Jan 1, 1988

By M B. McKevitt, W J. Shaw

The main task of grade control on a daily basis is to define the material that should be mined to a destination under various categories. This can be determined by grade, lithology, quality and blending criteria. In the case of multi-element deposits or deposits with various blending or other processing criteria the optimum selection of ore block boundaries can be quite complex. In every case the balance between ore loss and dilution must be considered when designing the ore block boundaries and this becomes a risk-based decision when using the conditional simulation model. The use of such systems allows grade control to meet specific targets, such as budget tonnages and grades and blended product specifications. Two case studies are presented: the Prominent Hill copper/gold mine and the Rapu Rapu zinc/copper mine. Mining is based on a rational grade control strategy involving a number of factors, including strong geological control, advanced geostatistical approaches, such as conditional simulation, and optimisation of the ore blocking to meet production requirements. This provides an objective, transparent and repeatable grade control strategy.

Jan 1, 2009