Search Documents

By C Li

Removal of gangue minerals from ilmenite concentrates can beaccomplished by relatively low temperature roasting in controlled gasatmospheres to selectively enhance the magnetic separationcharacteristics of the ilmenite. At roasting temperatures below 800¦C the magnetising reactions are often not consistent with phase equilibria considerations. Metastable phases can nucleate and control the roasting products. In weathered ilmenites the phase assemblages and microstructures in the altered ilmenite grains can influence the roasting reactions. In this paper we give an overview of the phase chemistry of chemically weathered ilmenites and of metastable phases formed by low temperature roasting. We also report the results of roast experiments conducted in a neutral gas atmosphere. Major increases in magnetic properties after short roasting times at low temperatures were obtained for a range of ilmenite concentrates. For example heating a secondary ilmenite concentrate from Western Australia for 15 minutes in nitrogen at 600¦C gave an increase in the three kilogauss magnetic fraction from three to 92 wt per cent. The solid state phase changes accompanying the inert atmosphereroasts were characterised by combining elemental analyses withquantitative phase analyses of the ilmenite concentrates and their roast products. It was found that the phase reaction that is principally responsible for the increase in the magnetic properties of weathered ilmenites involves a transformation of disordered ferrous-containing pseudorutile to an ordered ilmenite-hematite solid solution containing typically ten to 35 mole per cent of the hematite component. Examples are given of the application of the inert atmosphere roast to effect separations of ilmenite from gangue minerals.

Jan 1, 2001

By S P, F Villanueva, R Palomo, D Meadows

During 2002, design and development of the worldÆs largest flotation cell was completed. The cell is the mineral industryÆs first 257 m3 flotation cell, and represents a major development in the design of larger flotation cells, with a 50 per cent increase in cell volume over the widely installed 160 m3 WEMCO« SmartCellTM flotation machine. It is anticipated, in the next few years, world-class copper sulfide concentrators will incorporate 257 m3 flotation cells in their rougher-scavenger flotation circuits. The prototype 257 m3 cell, No 250 SmartCellTM flotation machine is installed in Minera Los PelambresÆ existing rougher flotation circuit. The machine is located in front of the first cell in Row 1 and is followed by nine No 130 SmartCellTM flotation cells. The unit has been in operation since April 2004, and has proven itself in this duty. A key to the successful development of the equipment has been the emphasis placed on fundamental hydrodynamic scale-up criteria. Hydrodynamic factors include superficial gas velocity, water (pulp) circulation through the draft tube, and pulp mixing (distribution) characteristics. This paper will review the scale-up criteria of the No 250 flotation cell, and a case study will be presented on the in-plant testing of the equipment. The case study will document the metallurgical and hydrodynamic performance of the machine. It will also illustrate the economic benefits derived by incorporating larger flotation cells in a modern copper sulfide concentrator.

Jan 1, 2005

By Menne DM

The carbon-in-pulp (CIp)process has become well accepted and firmly established in the gold industry of South Africa and, at this stage, six large CIP plants are treating close to I million metric tons of material per month. Many small operators are also using CIP and additional large plants are either nearing completion, are on the drawing boards,. or are being considered. The programme of testwork that preceded the acceptance of the CIP process in South Africa was conducted over some eight years and has been previously described'-7. With the start-up of the President Brand CIP plant on 'calcine' in July 1980 and that of the Western Areas CIP plant on repulped filter residues in September 1980, the emphasis on the CIP process switched from pilot plants to these large plants - and has largely remained there. As it has started up, each new CIP plant benefited from the experience gained and the developments made, on earlier plants but, since so few plants have so far been established in South Africa, each new plant and each new design has revealed a further set of conditions to be met and problems to be overcome. However, in the highly collaborative atmosphere of the South African gold-mining industry, the results and observations from the operation of these first plants were shared by all mining groups. This paper will attempt to describe typical developments on, and results obtained from, these new large plants, and will incorporate significant results from the earlier laboratory and pilot-plant investigations.,

Jan 1, 1982

Placer Dome Asia Pacific operates eight mines in the region and has two closed operations that are either under rehabilitation or at the latter stage of care, monitoring and maintenance. All operating mines are scheduled to close within the next ten years based on current proven reserves. Mine closure planning and associated risk assessments are integrated into both strategic planning and day-to-day operations within the Placer Dome group. Mine closure is all about predicting the potential risks and Placer DomeÆs knowledge has improved following the planned closure at Kidston Gold mine in North Queensland. Planning for closure commenced in earnest in 1994, and focused on identifying the issues and associated potential risk to the environment, and ensuring that the most suitable control measures were implemented leading up to and following closure in July 2001. At all times during the process of planning, implementation, safety contractor management and post closure, the identification of risk and potential threats to the business have been identified and managed. Post closure risk assessment of rehabilitation strategies potential to fail has been completed in conjunction with URS and opportunities to manage these potential failures in perpetuity will be discussed along with lease surrender. Misima Mines is currently processing low-grade ore and plans to close in 2004. Planning for closure has been ongoing for several years with a focus on the social aspects and the impact of the mine closing on a remote island community. Misima Mines has assessed the risk profiles using a community closure focus group, to identify both the biophysical and social aspects for closure.

Jan 1, 2003

By J N. Moncrieff

The resource estimation process for the underground Mount Isa Copper Mine has undergone significant change. Block models are now created using a commercial software package as opposed to the in-house software that was previously used. With mineralisation occurring over a strike length of more than 4 km, Mineral Resources for all categories totalled 190 Mt at 2.7 per cent Cu at 31 December 2002. Estimation is by ordinary kriging with two separate models generated to cover the X41 and Enterprise orebodies respectively. The underlying Upper Basement Contact and the silica-dolomite alteration envelope are both used as hard boundaries to constrain the modelling. From a validated block model, grade shells are generated at the appropriate cut-off grade for a given area. The grade shells are depleted for mined voids and subdivided into 30 metre strike length blocks. Application of a SMU criteria and crown and pillar constraints results in failed blocks being culled from the resource inventory. Mineral Resource blocks are further subdivided into resource categories (Measured, Indicated, Inferred) by the Competent Person on the basis of geological confidence, taking account of geological and grade continuity, drillhole spacing and structural complexity (JORC, 1999). A geostatistical æconfidenceÆ category is incorporated into the block model as an additional tool for the categorisation process. The shapes are assessed in concert with a mining engineer to determine whether a reasonable expectation of mining potential exists and if not they are removed from the resource. The final categorised blocks constitute the Mineral Resource inventory and form the basis for conversion to Ore Reserves. The resultant Mineral Resources and Ore Reserves are reported on an æinclusive ofÆ basis.

Jan 1, 2003

By F Pothitos, S Hewson

The geological and geotechnical conditions at the Cadia Hill Open Pit are very complex. This complexity coupled with high mining rates has required significant technical input into the design and optimisations of the pit slopes, accesses, cutbacks and scheduling. A multi-discipline team of NML engineers, geologists and external consultants has been conducting comprehensive geological and geotechnical programs in order to achieve an optimum design of the pit slopes. Extensive data collection, analysis and interpretation has led to the formation of working geotechnical models of large structures, rock masses, and back-analysed slope performance charts. The current Cadia Pit Optimisation Project focuses on the risk-and-return principle for pit design and on the integration of geotechnical, hydrogeological, mining engineering and scheduling. The risk management for pit design has also been incorporated into the short term and long-term operation of the pit mining to ensure safety and production.

Jan 1, 2003

By E Haren, A Winchester

The CSA Mine has a long and varied history from initial discovery in 1871 through to the present. Lead-zinc mineralisation was mined historically near the surface. Today copper and silver are extracted from the deeper regions of the mine. The mine has passed through a number of owners over this time, each with a unique operating philosophy and understanding of the mineralisation. Cobar Management Pty Ltd re-opened the mine in 1999 and has undertaken extensive drilling programs to expand the resource and gain a better understanding of the mineralisation characteristics. Presently mineralisation has been located over a strike length of 1.2 km and to a depth of over 2.0 km with over 30 mineralised lenses from four identified ore systems. The refinement of geological and mineralisation models led to further discoveries and prompted a review and modification of resource modelling processes. Advanced statistical analyses prompted the implementation of ordinary kriging as a grade estimator. Improved stationarity from enhanced geological domaining has been supported by variography and kriging neighbourhood analysis studies. Resource models at CSA are now quantifiable in terms of mineralisation style and estimation reliability. The new techniques are assisting the definition of more mining fronts, which are creating new opportunities to increase mine output.

Jan 1, 2006

By Mackenzie W. R, Harding C. G

The Islamic Republic of Mauritania is a large country of over 1 000 000 square kilometres situated on the Atlantic coast of north-west Africa. It is bounded to the north by Western Sahara and Algeria, to the east by Mali, and to the south by Mali and Senegal. With the exception of a narrow strip in the south along the Senegal River valley, the country lies entirely within the Sahara. The north of the country is largely devoid of vegetation, and it is estimated that 90 per cent of the population of 2.1 million people live in the southern quarter of the country. From about the turn of the century, Mauritania was ruled by the French from Dakar in Senegal and, until 1960 when it obtained independence from the French, Mauritania did not have a capital. Today, the capital is Nouakchott, home to an estimated 600 000 Moors of mixed Arab, Berber and African descent. After independence in 1960, disputes over Spanish Sahara to the north led to a military coup in 1978 and it was not until 1991 that a democratic constitution was adopted. The new constitution declares Mauritania to be an `Islamic, African, and Arab Republic.' It provides for an executive president, elected for a six-year term, and for a bicameral legislature, consisting of a national assembly and a senate. The first presidential and legislative elections were held in 1992 under United Nations' supervision. Mauritania's economy is predominantly pastoral, and the country depends heavily on foreign aid. Its principal export industries are iron ore mining (about ten million tonnes per annum from mines near Fderik in the north) and fishing. Mines d'Or d'Akjoujt SA (MORAK), a company in which General Gold Resources NL (GGR) has 42.5 per cent equity, produces over 50 000 ounces of gold per annum, which represents the third largest export industry in the country.

Jan 1, 1996

Water is becoming an increasingly valuable commodity in Australia and the mining community is finding itself competing with pastoralists, domestic consumers and industry for access to what is an essential but finite resource. This paper will provide an overview of various legislative regimes in Australia governing water resources, and will review some of the fundamental issues which should be considered by mining companies when contracting with other parties for the supply of water. The paper will focus on mechanisms to secure access to water for mining purposes, and will deal with the following issues: Grants of water entitlements under legislation û (navigating the legislative requirements necessary to facilitate the taking and use of water for mining activities) The paper will focus on the key legislative requirements for securing access to water in Queensland, Western Australia, New South Wales, Victoria, South Australia, Tasmania and the Northern Territory, and will examine: compliance with regulatory processes for securing water entitlements through the grant of water allocations, licences and permits, etc; and dealings with water entitlements (ie statutory mechanisms for transferring water entitlements on a temporary or permanent basis). Securing access to water under water entitlements through contractual means. The paper will also review of some of the fundamental issues which should be considered by mining companies when contracting with holders of water entitlements for the supply of water from both groundwater and surface water sources. These issues include (inter alia): securing appropriate rights to take and use water in compliance with relevant legislation, the necessity to protect the validity of underlying water entitlements, ensuring the security of supply for the contract term, access rights affecting water entitlements and other important issues relating to the security of water entitlements for miners.

Jan 1, 2003

By George G

The Circum-Pacific Map Project is a cooperative international effort to prepare and publish geological, geophysical and mineral resource maps of the Pacific Basin and adjacent land areas. Earth scientists representing 180 organizations from more than 40 Pacific Rim countries are participating in the work. The project is directed by a committee established 14 years ago as an activity of the non-profit Circuin-Pacific Council for Energy and Mineral Resources. Technical and cartographic support is provided by the U.S. Geological Survey. The Circum-Pacific Map Project is organized under five regional panels of experts on the geology and resources of the four quadrants of the Pacific and Antarctica. A series of five 1:10,000,000-scale regional maps and a 1:17,000,000-scale map of the entire Project area, the Pacific Basin Sheet, provide the cartographic base. Forty-eight individual sheets are planned and thirty have been published in eight different series, including base maps, geography, plate tectonics, geology, energy resources, mineral resources, tectonics and geodynamics. Additional special single-sheet thematic maps on the Pacific Basin base have been published and are planned for a total of more than 50 individual sheets.

Jan 1, 1987

The Snap Lake Phase I project initiated a subsampling campaign on the material (kimberlite/metavolcanic/granite) mined and treated for diamonds. The campaign was aimed at determining the optimum subsampling program to subsample the feed to the bulk sample plant (BSP) for the duration of a sampling campaign. This paper describes the application of GyÆs formula for determining the subsample size and other good sampling practices to determine this subsampling campaign. Three main issues are discussed: the use of a hammer sampler to sample off a moving conveyor and the practical experiment to determine the optimum subsampling program; bias introduced by laboratory equipment including two sizes rotary splitters; and variability of the feed material to the BSP over time.

Jan 1, 2005

Drilling has disclosed a sequence of Cainozoic sediments immediately to the west of the Ediacara mineral field containing little or no dolomitic debris in the lower and middle sections, but with gravel beds of dolomite derived from local rocks in the upper part. It is suggested that the lower and middle sequence of Cainozoic strata was deposited over the area of the Ediacara Range, and that this range was uplifted, probably as a horst block, during Quaternary times and was first exposed to subaerial erosion during the upper Pleistocene epoch.Lower Cambrian dolomites with associated stratiform lead mineralization, which formed the target of drilling on the western downthrown block of the Ediacara Fault, were eroded before deposition of Cainozoic sediments.Intense leaching of basal Cambrian dolomites around the periphery of the Ediacara Basin took place during Mesozoic and Tertiary times. This leaching process has resulted in enrichment of copper and lead mineralization in a thick marginal zone of residual clayey material overlain by dolomitic collapse breccia. These zones of leaching and enrichment were preserved under Cainozoic sediments which have subsequently been eroded. The Ediacara Fault appears to have been a major conduit for mineralizing fluids and is the main lineament of the Torrens Hinge Zone. Contemporaneous movements on this fault have controlled rates of depositionand thickness of sediments across the fault during Adelaidean and Cainozoic times. Though latest movements of this fault have been west block down, the predominant movement has been east block down with associated thickening of sediments to the east in the Adelaide Geosync1ine.

Jan 1, 1972

By Barria J, Mencho J, Gonzalez GD

An extended Kalman Filter is used to build an on-line estimator of total ore, fine ore and water hold-ups in a SAG mill. In addition, an equivalent grinding rate from coarse to fine ore, as well as the discharge rates of solids (fines) and water are also estimated as part of the adaptation procedure of the model used for the Kalman Filter. The measurements used in the Kalman Filter estimator are the total mill weight provided by load cells, and inferred discharge flows of fines and water from flow and density measurements performed downstream. The net ore and water feed to the SAG mill are used as inputs to the estimator, and also the proportion of fine ore in the feed. As an example of how to introduce robustness in the estimation in the face of sensor bias errors, an estimation of the load cell bias error is introduced in the estimator, thus providing self calibration. The estimator presented in this paper has been tested by simulation using a detailed SAG mill mechanistic dynamic model comprising 27 size fractions well fitted to a pilot mill. The maximum error in the estimation of the operational variables - total and fine ore as well as the mill contents under different operating conditions - is about ten per cent.

Jan 1, 1993

By R M. Tosdal

Intrusion related ore deposits are widespread in the Central Peruvian Cordillera Occidental and adjacent high-plains to the east and include porphyry Cu (-Au, Mo; eg Morococha), Cu-Zn (Pb-) skarn (eg Antamina), Pb-Zn-Ag carbonate hosted vein deposits (eg Uchucchacua), cordilleran base metal (eg Cerro de Pasco) and epithermal deposits (eg Quicay). Geochronology and petrochemistry of intrusive rocks associated with mineralisation reveals that: most ore deposits were emplaced in the late middle to early late Miocene; and are related to calc-alkaline granodioritic igneous rocks with Sm/Yb >3, Sr/Y >40 and Y/Th <1.5. The largest deposits, including Antamina, Colquijirca and Cerro de Pasco are associated with intrusions with Sm/Yb >4 and which, as indicated by Pb and Sr isotopic data, have undergone relatively moderate middle and upper crustal assimilation. The chemical signature of igneous rocks related to mineralisation likely reflects melt equilibration in the lower crust at a crustal thickness of more than 45 km. Mineralisation was favoured by a change from normal to flat subduction, resulting in increased compression, crustal thickening and subsequent cessation of the magmatic arc. Premiocene ore deposits do occur, but are restricted to a broad E-W corridor between Uchucchacua and Milpo and probably were controlled by a crustal-scale structural discontinuity across the strike of theAndes. Not all igneous rocks with high Sm/Yb and Sr/Y ratios did acquire their trace element signature in the lower crust. Petrographic and Pb isotopic evidence indicates shallow crustal hornblende fractionation or assimilation of pelitic material as possible causes for high trace element ratios in some rocks. These are apparently unrelated to polymetallic mineralisation. Thus, critical evaluation of petrographic and geochemical data in metallogenetic studies, especially in areas with complex basement architecture such as Central Peru is critical and should not be reduced to simple trace element ratios. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

Mine planning is difficult. Even for small operations, it involves reasoning with complex variables and the practical difficulties of mining. It is also about predicting and planning the future in an unpredictable physical and economic environment. Yet we rely on a handful of individuals and their spreadsheets to tell us how to do it û planning the business and activities of mining to hopefully produce results that will please stakeholders. Does it work? Not as well as it could. Planning affects everyone in the organisation. Company executives are demanding more reliability and stability in cost and revenue forecasts from their operations. Management want to explore ways of being more cost effective. Miners and contractors want more useful plans and realistic targets. And the planners have to describe the method that will translate business objectives into implementable plans. Even with the use of computer technology a lot of effort is expended to produce plans that are largely qualified by the level of knowledge and experience of individuals. Better use of information and the application of Intelligent Technologies can improve the quality and reliability of mine plans and schedules. By capturing the knowledge within the organisation and speeding up the planning process, Intelligent Technologies allow more options to be considered more rigorously. But it is not just about technology. It is about how technology is implemented and embodied in the way the business is managed for performance. When this happens, the real benefits of better planning start to flow.

Jan 1, 2003

The magnesite deposits near Young, N.S.W., occur in decomposed serpentine rock below a soil. and alluvial cover. They show considerable variation in both quality and depth which greatly hampers mining operations. Seismic refraction techniques afford methods of conducting detailed and reconnaissance surveys which yield a depth and velocity analysis of the serpentine/magnesite refractor. The measured seismic velocities may be used as an index of the presence and quality of the deposits. The Seismic Timer which was used in the test surveys is a simplified seismograph which makes use of seismic reciprocity by replacing the conventional seismic shotpoints with geophone stations and the conventional geophone stations with impact points of a sledge hammer. Thi,s enables the use of detailed seismic refraction techniques which yield the depth and velocity analysis of the refractor.INTRODUCTIONThe magnesite deposits near Young, N.S.W., were produced by a process of leaching and enrichment of magnesium in serpentine rock. The magnesite occurs in nodular form emplaced in decomposed rock at shallow depths below soil and alluvium. The depth ranges from close to the surface down to some tens of feet. The deposits are patchy and show considerable variation in both quality and depth, giving riseto considerable difficulties in mining operations.Due to the thorough leaching of the surface material, geochemical tests carried out so far have not proved satisfactory for locating the pockets of magnesite enrichment.It was decided to test the application of detailed shallow seismic refraction methods to the investigation of both the depth and quality of the deposits. The tests were carried out...

Jan 1, 1962

By Li G, Dean-Jones G. L, She T

Highwall mining is a specialised and largely automated mining method developed in the United States for the extraction of coal left under a shallow overburden cover after cessation of economical open cut mining operations. As the name indicates, coal is extracted from the seam exposed along a highwall by a remotely controlled continuous miner operating in a single unsupported opening and brought to the surface by a string of conveyor segments. The single entries are separated by coal .pillars and driven normal to the highwall, over areas where the thickness of cover and volume of recoverable coal is insufficient to allow or justify conventional underground mining. An additional highwall mining method is augering. The success of high wall mining operations depends significantly on geological features, notably the stability of the working roof, determined by the type and mechanical properties of the immediate roof strata. Stability of the ribs, absence of floor heave, faults and dykes are further important prerequisites for profitable highwall mining. The geometric relationship between the spatial attitudes of existing joint systems, the direction (azimuth) of the single entry opening and its vertical profile determine the unimpeded depth of penetration into the coal and thus its economic success. The mechanical implications of the lithological transition zone from a coal seam to either primary or original roof strata, compared to an interface between the coal seam and overlying strata, characterised by a sharp erosional boundary between coal and a secondary immediate roof stratum, are very significant. The compatibility between the response to mining by the geological system (floor-seam-roof) and the capability of the mining equipment to prevent the development of instability are essential requirements from a mechanical viewpoint. The minimisation of vibrations, very good horizon control, an ability to vary the profile of the opening, and the maintenance of consistently high advance and retreat rates, are also important aspects of profitable highwall mining.

Jan 1, 1995

IN preparing a sample of refined lead for analysis, it is necessary to exercise great care to avoid contaminatien, as the amounts of the various impurities present in market lead are very small. The lead is cut into convenient-sized pieces, which are flattened out with a hammer, so that, on putting tbe lead through the rolls, strips of about one inch in width and Ij32iu. in thickness are obtained. The hammer, anvil, and rolls should be carefully cleaned before use. The strips oflead are cut up into pieces of about one inch square. If the lead is roIled out very thin and cut up into small pieces there is considerable risk of the acid acting too violently and causing loss through frothing over. A blank assay on all the reagents used should becarried right through, along with the actual analysis of the lead. This is of the greatest importance, particularly with regard to the determination of such impurities as iron, sulphur, arsenic, and antimony.METHOD OF ANALYSISThe method of analysis is as follows: Take two lots of 600 gIm. each, place in a large beaker, add 2000 cc. distilled water and 750 cc. concentrated HNOs. Cover with a clock glass and warm on a hot asbestos plate until all action ceases. (If any white precipitate forms, filter off and examine for Sn and Sb.) Add 420 cc. H2S04 (1-1), and stir well while adding the acid: Allow PbS04 to settle, pour off the clear liquid into a 12-in. porcelain evaporating dish, and start evaporating down, the dish being placed directly on an 8-in. ring gas burner. Wash the precipitate three times by decantation using approximately 1200 cc. hot water for each washing, and stir well...

Jan 1, 1922

Throughout the Kalgoorlie Field the dominant factors influencing all planned exploratory work are: firstly, the general geology of the district, and, secondly, the lode fracture pattern. Superimposed on these, there are innumerable faulting problems which tend to complicate the search for ore.In this paper it is proposed to deal primarily with the lode fracture pattern and to touch on the general geology only insofar as it affects ore distribution. So much has been written on Kalgoorlie geology that it would be impossible to review the literature adequately in a brief paper such as this. The basic facts of rock types and rock distribution are well established and the broad structure of the field is known in the central portion, though it is less well established towards the northern and southern ends.The latest descriptions of the general geology are those of Stillwell (1), and Gustafson (2), -and these represent the basis of current knowledge.GENERAL GEOLOGY.The field is six miles long and about one mile wide, the long axis trending north-west. The "Golden Mile," or heart of the mining 'area, covers a length of three miles in the southern section, and consists of a central core of quartz dolerite greenstone which merges into uralitic quartz 'dolerite on its western margin. The uralitic quartz dolerite is derived from an original quartz dolerite by a low grade...

Jan 1, 1948

Looking back 25 years, the role of the drill and blast engineer in an Australian mine seemed relatively simple, with the primary focal points being scheduling of the drill rigs, oversize control, and budget control with respect to consumption of both explosives and drill consumables. The choice of explosive selection was relatively simple, though many mines were becoming involved in trials of slurry explosives, emulsion blends, and low density ANFO blends. Guidelines to assist the engineer towards specific fragmentation targets were scarce, environmental constraints were light, and computers were rarely found on the desks of any mining engineers. Wall control blasting was in its infancy, with the bulk of attention being given to appropriate slope design and little real attention given to factors such as explosive distribution, and optimum delay timing and sequencing. Quantitative measurement of blasting performance was rare. The science of blasting, for fragmentation control, wall control, and environmental impact control was about to be born, and was heralded in those years by intense efforts by the explosive manufacturers and a proliferation of research centres throughout the world. Since the early 1980s, the role of the Australian drill and blast engineer has gone through a major metamorphosis, and currently requires a greater depth of scientific understanding than any other specialisation within mining engineering.

Jan 1, 2004