Search Documents

By John C. Loretto

"The paper identifies two of the main problems encountered in recent hydrometallurgical plants for the recovery of gold and silver: firstly, the plant recovery is lower than anticipated from the testwork; secondly, the metallurgical accounting figures cannot be reconciled.The principal reasons for the plant recovery being lower than the testwork are discussed, together with solutions that can minimize these problems both during the design stage and during the plant operation after the problems have manifest themselves.The reasons for the difficulties in metallurgical accounting are analyzed by reviewing the various components of the plant figures. Recommended solutions are given for minimizing this problem and the realities of obtaining accurate figures are discussed.IntroductionThe start-up over the last few years of new hydrometallurgical plants for the recovery of gold and silver has brought to the surface again a number of problems. Most of the problems have existed for some time and they manifest themselves mainly in two ways. Firstly, the plant results do not agree with the metallurgical testwork figures; secondly, the metallurgical accounting figures do not balance.Metallurgical TestworkThe plant results not agreeing with testwork figures are mainly due to:a) testwork samples not representative of the eventual plant feed;b) misinterpretation or misunderstanding of testwork ;c) plant losses;d) plant design not allowing testwork results to be achieved;e) operating deficiencies."

Jan 1, 1982

By Z. Bibak, S. Banisi, A. Ghasemi, E. Nematollahi

"The major importance of liners in grinding is their role in providing an appropriate trajectory for the charge. Since it is not possible to study the charge movement by direct observation in operating industrial mills, this task is accomplished by physical (laboratory), and/or, mathematical (software) methods. Because of the high cost and a longer time required for a physical analysis, mathematical simulations have become more common. Simulation of the effect of liner shape on the charge movement has provided a means to select a proper design based on the operational objectives and conditions. Furthermore, the liner shape changes due to wear and impact during operation, which will influence the charge trajectory. This adds more of an incentive to use simulation. These changes in liner could be predicted through liner profile measurements during operation and/or simulation. In this research, an inhouse developed DEM software called KMPCDEM © was used to simulate the charge movement in industrial plant SAG mills. A geometrical method of implementing the shell liners on SAG mills at the Sarcheshmeh (9.75×4.87 m) and the Gole-E-Ghohar (9×2.05 m) operations facilitated the software simulation. Point by point implementation of the measurements of liner profiles of these mills enabled the study to trend the change in the charge movement as the liners wear. Comparison of the simulation to a laboratory mill (1 m diameter) showed that the difference between the measured and predicted charge impact point, shoulder angle and toe angle were 6, 4 and 3°, respectively.INTRODUCTIONComminution is the most energy intensive operation constituting the major portion of operating and capital costs of a mineral processing plant. In the last decade, a vast number of research was aimed at studying various aspects of grinding with the aim of performance improvements (Davis, 1919; Mishra & Rajamani, 1990; kalala, Breetzke, & Moys, 2008). Mill liners transfer the input power to the charge and play a significant role in affecting the motion of the charge (Mclvor, 1983; Mishra & Rajamani, 1990; Radziszewski, 1997; Van Nierop, Glover, Hinde, & Moys, 2001; kalala et al., 2008). Lifters are usually used with mill liners to extend their life and to enhance the grinding and impact breakage efficiency. Mill lifters are used to raise the grinding media and ore to transfer the energy from the mill to the load (Rezaeizadeh, Fooladi, Powell, & Weerasekara, 2010)."

Jan 1, 2016

By G. R. C. Pacheco, D. M. Fonseca, R. Neuböck, G. E. Gonçalves, W. Moulin-Silva

Degradation by sulfur gases is an important lining wear mechanism in the copper industry. SO2/SO3 gases infiltrate into the pores of the basic refractory bricks, combine with their raw materials through expansive reactions and significantly modify the bricks’ structure. This study presents a comparison of the corrosion resistance against sulfur attack of different magnesia-based refractories using a simple, low-cost and quantitative method. Recipes containing sintered MgO grains showed lower resistance to corrosion by sulfur oxides compared to basic grades containing fused grains. Chromium corundum grades were used as a reference and showed very good resistance to this corrosion mechanism under the test conditions. The novel test provided relevant results that agree with what is commonly observed during operation and in previous post-mortem studies. This tool could be very useful in selecting refractory grades for the copper industry and predicting their performance. INTRODUCTION Oxidation of matte sulfides during copper production leads to the formation of sulfur oxides, which infiltrate into the pores of the refractory lining and react with the basic oxides below 1000°C to form magnesium and calcium sulfates. This reaction is accompanied by an expressive volume increase, consequent densification of the refractory microstructure and weakening of the brick bond (Malfliet et al., 2013). Thus, corrosion by SO2/SO3 is an important wear mechanism in the non-ferrous industry and the resistance to this compound should be considered when defining refractories for this application. Previous studies on this matter include expensive and complex testing methods involving pressurized SO2 gas cylinders in order to investigate the corrosion resistance of MgO-containing materials by sulfur oxides (Gerle & Podwórny et al., 2016; Fotoyi & Eric, 2011; Fotoyi, 2009; Podwórny & Piotrowski et al., 2008). The current study was based on a test developed by Pacheco & Fonseca (2018) to assess alkali infiltration and aims to provide an evaluation method of the corrosion resistance of refractories by SO2/SO3 in a simple and quantitative manner. This novel test is useful to compare the corrosion resistance of different refractory recipes and properly select the grades that should be employed in the non-ferrous industry. A case study is provided to illustrate the damage caused by sulfur oxides in refractory linings.

Jan 1, 2019

By J. Oliver, B. Wilson, 10

"Red Dog is one of the world’s largest zinc producing mines and a significant producer of lead and silver. While some of the operational challenges relate to the mine’s location in a remote part of Alaska, there are also challenges in the mineral separation process. Recent processing upgrades have included the installation of two M5000 IsaMills to improve the zinc regrind circuit and of one Jameson Cell to improve the pre-flotation circuit. Relatively fine grinding is required to achieve efficient mineral separation at Red Dog, but while fine grinding aids in the production of high grade concentrates, it also creates challenges in the efficient recovery of fine minerals. Over half of the lead lost to the lead circuit tailings, as well as almost half of the zinc lost to the final tailings, is in the finer size fractions (<10 µm). The high pulp density experienced in the pre-flotation and lead rougher circuits also causes significant entrainment loss of lead and zinc to the pre-flotation concentrate and of zinc to the lead concentrate. To help improve fine mineral recovery, Red Dog has recently plant tested and installed magnetic conditioning technology in the flotation circuits. The equipment aggregates fine paramagnetic sulphides and selectively increases their flotation recovery. This paper outlines the testing and positive results at Red Dog.INTRODUCTIONRed Dog is the largest zinc mine in North America and represents approximately 29% of North American zinc concentrate production. The mine is located in northwest Alaska, approximately 100 miles north of the Arctic Circle and 50 miles inland from the Chukchi Sea. The remote location makes the mine accessible only by air or seasonally by ocean-going barges. Red Dog is a partnership between NANA Regional Corporation Inc, the land owner and Teck Alaska Incorporated, the operator of the mine. Red Dog Ore and Mineralogy The Red Dog deposit is a rich sedimentary exhalative (sedex) zinc-lead-silver deposit. The main minerals present in order of abundance are: quartz, sphalerite, pyrite, barite and galena. Production began in 1989 with mining of the Main deposit. Between 1989 and 2012, approximately 55.6 million tonnes of ore with an average grade of 20.5% Zn, 5.6% Pb, and 97 g/t Ag was mined from the Main deposit. Subsequent to the development of the Main pit reserve, two additional open pit deposits were discovered: Aqqaluk and Qanaiyaq. The first blast in Aqqaluk occurred on June 4, 2010. As of December 31, 2014, the Aqqaluk deposit reserve is an estimated 45.7 million tonnes of ore with an average grade of 15.1% Zn, 3.9% Pb and 71 g/t Ag."

Jan 1, 2016

By E. Ghali, N. Sorour, G. Houlachi

"The binary Fe53Mo47 and ternary Fe54Mo30P16 coatings have been electrodeposited from citrate-based electrolyte on mild steel (MS) substrates. The electrodeposition has been conducted for 6 hours at 20 mA cm-2 and 30°C. The electrochemical tests were carried out in chlorate solutions containing 300 g L-1 NaCl and 4 g L-1 K2Cr2O7 at pH 6.4 and 80°C. A number of surface characterization techniques such as SEM-EDS, XRD and EMP were used to study the microstructure of the alloys. The electrocatalytic activity of these coatings was investigated using steady-state polarization and galvanostatic technique. This study revealed that the Fe-Mo-P coating could be considered as a promising cathode material for the hydrogen evolution reaction (HER). The results showed an important decrease of hydrogen overpotential for Fe-Mo-P alloy as compared to that of Fe-Mo and especially MS which is a traditional cathode in chlorate industry. The HER overpotential for Fe54Mo30P16 at current density of 250 mA cm-2 was decreased by 30% in comparison to that of MS (1029 mV), and by 16.5% to that of Fe53Mo47 coating (857 mV).INTRODUCTIONSodium chlorate is used for manufacturing of several daily consumption products. This chemical is mainly employed for the production of chlorine dioxide (ClO2) that is a bleaching agent used in the pulp and paper industry. The ClO2 is also consumed for generation of perchlorates, chlorites and other chlorates, as an herbicide and in uranium processing (Cornell, 2002). Sodium chlorate is produced industrially via following overall formula in un-divided electrochemical cell (Nylén & Cornell, 2009):"

Jan 1, 2016

By T. S. Golosinski

"This paper reviews the types of selective continuous miners (SCMs) available at present, and compares their main features. Furthermore, operating practices and mine planning aspects of the SCMs applications are reviewed and conditions for efficient application of this equipment are defined. Finally, the potential applications of the SCMs in surf ace mining of oil sands are discussed INTRODUCTIONIn the 1970s the United States Bureau of Mines (USBM) conducted a program of investigations, design and demonstration of various continuous surface mining concepts, This included continuous mining equipment which was an adaptation of several civil engineering and/or underground mining machinery concepts to surface mining. Upon termination of this program, the related development was continued by a number of equipment manufacturers, leading to development of several types of SCMs. This new type of surface mining equipment is able to mine selectively hard and thin multi-layered formations at high, sustained, and economically viable production rates.While used mostly in coal mining at present, the characteristic features of this equipment permit conclusion that it may prove to be an efficient tool for surface mining of oil sand, and/or related overburden stripping. Of particular interest here may be the ability to mine thin layers of hard material, without a need for its earlier fragmentation, and the ability of the SCMs to load a variety of haulage equipment, including belt conveyors."

Jan 1, 1989

By Eric D. Jamieson

"How well is the Canadian coal industry able to expand in the tough competition with other fuels in Canada and with other suppliers in the international, metallurgical and thermal coal trade? Coal production as a whole decreased between 1950and 1960 and, although there has been a tripling of production since then, underground production continued to decrease until 1975. This trend has been reversed to a certain extent as a result of the modernization of mines in Cape Breton, but in 1978 over 85% of coal production came from surface mining.Against this background, the paper reviews current Canadian mining operations as described in papers presented at the 1979 CIM Annual General Meeting. Conclusions are then drawn regarding some of the longer-term mining applications in relation to the latest coal demand forecast, which indicates a potential Canadian production requirement of 160 million tonnes per year by 2000. IntroductionThe Canadian &apos;coal industry is experiencing a period of expansion and a new record for production is set with each passing year. This growth pattern over the last IS years has been based on two main markets-the generation of electricity in Canada and the export of coking coal to Japan. Supply to those markets has entailed either the development of mining, coal preparation and transportation systems for the delivery of large volumes of products with predetermined specifications or the establishment of minesite plants designed specifically to suit the characteristics of the coal in the adjacent deposits (Fig. I).Coal is a low-value commodity in relation to its bulk, and the economics of coal use become progressively less attractive with increasing distance from the producing mine. The transportation component in the export trade and in the movement of western coal to Ontario is a major cost factor. In the latter case, it approaches the cost of coal produced at the mine. In addition, the .international competition among coking coal producers chasing diminishing markets in a worldwide steel recession as well as the competition from U.S. coals and other fuel s for Canadian thermal coal have introduced a tight set of parameters to govern mining practices in all parts of the country. Some appreciation of the required changes in mining techniques brought about by declining traditional markets and the rigorous demands of the new bulk markets can be gained by comparing production from surface and underground mines over the past 25 years (Fig . 2)."

Jan 1, 1980

By Lynne Bowen

"On the da y shift in Number One Mine at Nanaimo on Vancouver Island, on May 3, 1887, William Griffiths, a coal miner with many years experience, fired a shot to advance the face of the crosscut. A flame ran out for a distance of fifteen feet along the roof and then extended up the slope for ten to twelve feet, and although many would have called this a blowing out shot, Griffiths said it was just a feeder. ""A blower"", he said, ""would have caused an explosion."" 1There was no explosion. Griffiths reported gas and the area was cleared for three hours and then work resumed. When the shift changed at 3:00 p.m., the fireman reported all places clear of gas and the ventilation good.2The ventilation in Number One Mine was the best anyone had ever seen. The air in the mine was almost too cold. The current was so strong that it sometimes blew out the flame on the miners&apos; fish oil lamps. It delivered five to six hundred cubic feet of air for every man and animal working in the mine. The law required only one hundred cubic feet 3The miners considered Number One to be relatively safe. The manager was proud of the mine and its up-to-date equipment"". Recently, there had been reports from France and America about the explosiveness of coal dust, but the manager did not think his mine was sufficiently dusty to be dangerous.5 The dust lay thick on the floor of the mine. Sometimes when a shot was fired the dust rose in great clouds. When a miner was shovelling it, the dust would billow up and be carried off by the current of air. The dust was also in the roof and in the stopings, put there intentionally to fill up the spaces and prevent the accumulation of methane gas."

Jan 1, 1992

By Stephen C. Tadolini

"The use of a torque wrench to establish the amount of actual load developed on an expansion anchor bofting system dates back to work completed in the early 1950s. The advent of ultrasonic measurement systems and hydraulic torque wrenches has made it possible for the U.S. Bureau of Mines to perform torque-tension measurements in the laboratory and the field much more accurately. The results indicate that the amount of initial boft preload may be overestimated by amounts in excess of 45% of the expected load using torque wrenches. This inaccuracy is primarily due to the friction that occurs between the bearing plate and the head of the boft. These parameters become extremely important when the support system is being used to prevent joint members from slipping relative to each other or when the boft acts as a heavy spring to clamp two or more sections together. Methods to overcome the frictional losses are presented in conjunction with a laboratory method to determine the actual torque-tension ratios for expansion anchor and combination bolting systems.IntroductionMechanically anchored roof bolts have been widely used in the mining industry since their introduction in 1947. Estimates made in 1989 indicate that out of 85 million fixtures, approximately 49 million bolting fixtures still use applied tension to complete the reinforcement necessary to maintain stable openings. Nearly 85 million bolts are used yearly. The most widely used bolt is the resin-anchored headed rebar, followed by standard mechanical roof bolts, specialty bolts (mechanically anchored, resin enhanced fixtures) , and combination bolts . Po st-tensioned resin rebars, combination systems, and friction stabilizers make up the remaining 10% of the units used (Fig. I).For mechanical, combination, and tension rebar bolts, the bolt tension is the primary means of reinforcing the roof, but in many cases, because of poor installation procedures, the bolts are ineffective. Mine operators recognize the importance of proper installation procedures. Long-term bolt tension measurements are required in the Code of Federal Regulations (CFR)In each bolting cycle, the actual torque or tension of the first tensioned bolt installed with each drill head shall be measured immediately after it is installed. Thereafter, for each drill head used, at least one roof bolt out of every four installed shall be measured for actual torque or tension. If the actual torque or tension of any roof bolts measured is not within the range specified in the roof control plan, corrective action shall be taken."

Jan 1, 1991

Purpose of TSUG Continuous Improvement in Mining Share Best Practises Exchange Ideas Network for Frontline Supervisors and Middle Management Meetings ? Two per Year -Spring and Fall ? Thirty Five to Forty Attendees ? Rotate Between Host Properties ? Host Mine Provides ? Meeting Room for One Day Tour of Mine and Maintenance facilities on Second Day

May 1, 2010

By V. Silins, J. Tameling, R. C. Cook

"A general review of the wear problems encountered in the mining industry is presented and current practice for wear protection systems is reviewed.A new concept in wear protection is described and compared to alternative systems. Utilization of conventional stud welding technology and abrasion-resistant wear studs is shown to be a useful supplement or substitution for conventional techniques. Operating life of many consumable components can be increased by up to four fold. The technique is highly portable for on-site field application or can be used in shop environments.Details of the wear protection model and metallurgical properties of the wear component are also reviewed. Laboratory wear test data are reported to supplement field test performance or to screen potential alloy compositions for application in specific environments.A Review of Wear Problems and Wear ProtectionThe emphasis on wear protection has increased in recent years because of the increasing impact of the potential savings in time, materials and energy. A 1974 German study concluded that attention to tribology, the study of friction and wear, could save approximately $3 billion, and a study in the U.S.A. at the same time put the figure at $100 billion of which $20 billion was for materials. A more recent American study put the energy component of the potential savings at $16.2 billion per year. A recent British study estimated the total potential savings in the U.K. as $1 billion per year, with the largest savings coming from lower maintenance and replacement costs ($500 million), lower breakdown costs ($250 million) and increased machinery life ($200 million). These three major contributions are all potentially accessible in the mining industry."

Jan 1, 1982

By Chris Yellowega

The construction and startup of a new mine is a daunting task. To successfully locate, design, build and startup an immense human endeavour like a new mine, takes perseverance, planning, dedication and significant capital. The application of capital requires a thorough evaluation of risk and where that risk is most properly limited to create the risk/return profile. One area of significant capital and thus, significant risk is the selection and maintenance of the very machinery needed to deliver the creation of investor wealth. Albian Sands Energy is the operator of the new Muskeg River Mine located north of Fort McMurray in Alberta?s oilsands. The Muskeg River Mine is owned by a joint venture of three companies: Shell Canada, Chevron Canada Ltd.and Western Oil Sands. The mine is designed to run 400,000 tons per day, 365 days per year. The mine conditions vary from material as hard and of similar consistency to pavement to underfoot conditions as soft as saturated sands. Water cannot be drained below surface conditions, shovel teeth can disappear in less than 24 hours and the primary business is often constructing large civil structures that have little to do with the delivery of ore. The mine starts with the deposit (if it doesn?t exist, nothing else matters), moves into the design, the feasibility study and the approval. The evaluation of risk and the strategies surrounding the control of that risk truly lie after these stages are complete. The strategy and execution stage is where risk is eliminated or accommodated. The point at which the investors money is being spent is the point at which the decisions made cannot be reversed. It is of absolute importance that the execution of the decisions are consistent with the strategy agreed to, lest the investors need to be asked for more money. The key sources of risk identified for the Muskeg River Mine were recruitment of trained and experienced personnel and the delivery of ore to maximize early (<2yr) cash flow. The Muskeg River Mine personnel determined that to minimize risk, personnel would be recruited to operate the mine equipment yet, the requirements for maintaining the equipment would best be held by the manufacturer. The strategy was to obtain the correct equipment for the operation of the mine and leverage the supplier?s expertise to ensure the mine wasn?t training a maintenance organization at the same time as a mining organization. In essence the key strategy for the mine start up and early operation was to leverage the equipment suppliers to maintain and repair the equipment. Albian Sands would maximize the utilization of Maintain And Repair Contract?s.

May 1, 2003

By C. Campero, C. Nicolau, L. Pagliero

The Chilean Congress has recently promoted desalination as a solution to meet the mining industry’s growing water demand. However, this rapid expansion of desalination infrastructure comes with trade-offs. This includes a significant energy cost for treatment, as well as socio-environmental impacts on indigenous communities, tourism, fisheries, and the marine ecosystem. This paper advances a regional-scale model for analyzing competing trade-offs through a case study in the Antofagasta mining region of Chile. Through geospatial data analysis in ArcGIS, new desalination infrastructure investments supplying water to mines are overlain with features of concern raised by communities during the environmental impact assessment (EIA) process, such as national parks, fisheries and exploitation areas for benthonic resources. The resultant model provides a test-bed for analyzing the cumulative effects associated with desalination expansion and for investigating scenarios to mitigate negative social-environmental impacts. The model simulates alternative scenarios for desalination locations and pipeline routes according to competing constraints (i.e. to minimize cost and energy constraints while also avoiding ecological and social hotspots). The ultimate contribution of the work is a demonstration of how the proactive adoption of a regional-scale infrastructure planning might have led to different desalination investment decisions. INTRODUCTION Chile represents the largest producer of copper globally, and holds approximately a third of the world’s estimated copper reserves. However, access to water represents a major constraint to industry expansion and creates conflicts with competing water users (Aitken et al., 2016; Côte et al., 2010). Recently, the Chilean Congress has promoted desalination as a solution to meeting the industry’s growing water demand, which is likely to lead to significant growth in desalination infrastructure to support large-scale mining projects that extract freshwater over a rate of 150 l/s1. By most recent projections, the Chilean copper mining sector is set to increase seawater use by 230% by 2029 (Faversham House Group Ltd, 2019). By the year 2015, Chile had 11 projects serving the mining industry and there are at least other 12 planned plants (Cochilco, 2015). While the use of seawater allows continued expansion of the sector without depletion of scarce underground aquifers, it is nonetheless accompanied with important socio-environmental drawbacks. One such challenge with desalination is the associated energy costs, expressed, both economic and environmental (e.g., CO2 emissions). This includes the energy required for reverse osmosis treatment facilities, as well as to pump water to inland regions at high elevations around 3.100 m.a.s.l in Chile. (Dixon, 2013; Knops et al., 2013). Additionally, the impacts of desalinated water use on flotation chemistry are generally poorly understood, necessitating the need for further research into the impacts, both positive and negative (Cisternas and Gálvez, 2018; Liu et al., 2011).

Jan 1, 2019

By B. Kruger

The Dundee Precious Metals Tsumeb Smelter has evolved over the last decade to meet the challenges and opportunities brought about by a changing copper concentrate market, technological advances, environmental legislation as well as social and political changes. The paper discusses some of the challenges, successes and lessons learnt through the expansion and modernization of its smelter complex. It considers the details and impact of the transition from slag granulation to that of slag slow cooling as well as the improvement program that was implemented to more than double the refractory campaign life of the Ausmelt furnace from around 6–9 months to 15–18 months. In addition, given the evolving world we live in, it considers the challenges that the smelter faces today, not the least of it being how to remain relevant in an age of digital and other 4th Industrial Revolution disruptions. INTRODUCTION Dundee Precious Metals Tsumeb (DPMT) Smelter is located just outside the town of Tsumeb, in the Oshikoto region of Namibia. It is the largest town in the region with a population of approximately 45,000. The smelter was built in the early 1960s to treat concentrate from the nearby Tsumeb copper mines. Construction of the site was completed in 1962 and the smelter was officially commissioned in 1963 by Tsumeb Corporation Limited (TCL). At the time the smelter consisted of a lead section (including a refinery), a copper section and plants that produced cadmium, sodium antimonite and arsenic trioxide. Production commenced in early 1964, with 3,500 tonnes of copper and 6,000 tonnes of lead being produced per month. TCL was acquired by Gold Fields South Africa in 1988, and a few years later the lead section was shut down due to reduced lead content of the mined ore. In mid-1996, all mining and smelting operations were halted due to labour strikes. Ongopolo Mining and Processing Limited (OMPL) re-opened the mines and the smelter in 2000, only operating the copper section of the smelter. At the end of 2008, all mining operations were halted by the new owner of OMPL, Weatherly Mining International, while the smelter continued to operate. The closure of the Weatherly owned mines in Namibia, the primary feed source to the Tsumeb Smelter, meant that the smelter had to transition its business model from operating as a ‘captive smelter’ to that of a ‘toll smelter’. Its Ausmelt Top Submerged Lance (TSL) smelting technology and various ancillary plants made it especially suitable for accepting and treating complex concentrates that were available on the global market.

Jan 1, 2019

By Joseph Carlston

With environmental regulations continuing to restrict the discharge of phosphorus from wastewater treatment facilities, traditional methods of phosphorus removal are proving inadequate. To achieve the phosphorus control necessary, a new coagulant used for phosphorus removal, cerium chloride, has been studied in several municipal and industrial wastewater treatment facilities that must meet a phosphorus discharge limit of 0.5 mg/L or lower. These studies demonstrated the high phosphorus removal capabilities of cerium chloride, with the results illustrating the ability for cerium chloride to reduce phosphorus to low concentrations in the effluent using a lower volume of product as compared to traditional coagulants, such as ferric chloride. This reduction is due to the unique ability of cerium chloride to remove phosphorus as cerium phosphate, whereas iron- and aluminum-based coagulants rely on adsorption and co-precipitation.

Jan 1, 2014

By D. K. Sarkar, Ying Huang

"Superhydrophobic thin films were fabricated on aluminum alloy substrates by chemical etching followed by passivation with organic acid molecules; (ii) electrophoretic deposition (EPD) of functionalized ZnO nanoparticles and (iii) electrodeposition of organic-inorganic composite materials. The physical and compositional analyses of the deposited thin films were characterized by SEM, FTIR, XRD as well as contact angle goniometer. The contact angle and surface roughness of the superhydrophobic surfaces prepared by the chemical etching process were found to be 156° and 2.29 µm, (ii) by the EPD process were found to be 155° and 4.54 µm and (iii) by the electrodeposition process were found to be 159° and 7.11 µm, respectively.The corrosion properties were analyzed with both polarization and electrochemical impedance spectroscopy (EIS) in NaCl aqueous solutions. The results demonstrate that the superhydrophobic thin films on aluminum alloy substrates display better anti-corrosion behavior than the as-received aluminum substrate. The comparison of results pertaining to the compositional and corrosion properties of these thin films on aluminum will be discussed in this work.INTRODUCTIONSuperhydrophobicity is defined as a surface property which provides non-wetting characteristics with a water contact angle larger than 150°. It is observed that the creation of certain micro-nanoroughness structures promotes the entrapment of air in the spaces of the rough surface morphology. In addition, lowering the surface energy helps to reduce the affinity of water drops to the surface, thereby weakening the water-surface interaction. Recently, various fabrication methods for superhydrophobic surfaces have been explored (Sarkar, 2010, Huang, 2010, 2011, 2013, 2015a, 2015b), such as the sol-gel process (Brassard, 2011), plasma treatment (Marchand, 2013), chemical vapor deposition (Zheng, 2009), chemical etching (Saleema, 2011), electrodeposition (Ying, 2011) and electrophoretic deposition (EPD; Huang et al., 2015b)."

Jan 1, 2016

By Matt Manson

?? Current Exploration and Assessment ?? Overview of Potential Development ?? Infrastructure ?? Opportunities and Challenges ?? Renard? 1-10 kimberlite pipes and ?Lynx-Hibou? kimberlite dyke system within ?Foxtrot? property ?? 50/50 Joint Venture between Ashton (a subsidiary of Stornoway) and SOQUEM ?? Discovered 2001-2003 ?? Québec is routinely assessed as one of the top mining jurisdictions in the world ?? Agnico-Eagle Mines Ltd. Is Stornoway?s largest shareholder and a leading mine developer in Québec

May 1, 2008

By T. P. Lim, N. K. Davé

"A modified accumulator method was devised to measure surface radon flux from porous media. It consists of a collector hood type of accumulator with a homogenizer pump and a pressure balancer. The latter was used to compensate any pressure changes produced during sample withdrawal and hence eliminate additional radon transport from the media. Errors resulting from radon back diffusion due to decreasing concentration gradient with time across the interface were also eliminated by measuring radon concentrations in the accumulator for two different periods of time and calculating the true radon flux, J(o), from the solution of a time-dependent radon transport equation in the absence of any pressure and temperature gradients.Core samples from the observation site were also withdrawn for laboratory determination of porosity, moisture content, bulk and grain densities, Ra-226 source concentration and the fraction of Rn-222 produced in the void volume. The data were used to calculate the radon diffusion coefficient for the media.Using the present method, the true value of surface radon flux for an abandoned uranium tailings pile was obtained as J(o) = 2020.2 mBq/m2/sec (54.6 pCi/m2/sec) compared to the value J = 1406.0 mBq/m2/sec (38.0 pCi/m2/sec) obtained by the conventional method. The bulk diffusion coefficient of radon for the media was obtained as 1.2 x 10-7 m2/sec.IntroductionRadon-222 (hereafter called radon) released from uranium mill tailings is a continuous source of environment radioactivity in terms of its transport as an airborne gas and its decay products. The particulate daughter products readily attach to aerosols or dust particles and can further be transported by various other environmental pathways. Typical radon release rates from existing tailings piles vary between 740 and 14,800 mBq/m2/sec (20-400 pCilm2/sec), depending on the nature of the tailings material, moisture content, etc. The United States Nuclear Regulatory Commission (NRC) is proposing radon release rates of 74 mBq/m2/sec (2 pCi/m2/sec) above that of background."

Jan 1, 1982

By G. R. Sadowski

"Large subhorizontal joints have been found in the foundation excavations in basalt and granite of Brazilian Dams. Some spread for hundreds of square meters showed slickensides—polished surfaces plus striations—and laminations interpreted as related to shear displacement, what substantially reduced their shear strength and imposed special reinforcement measures against the potential sliding of overlying concrete structures. The geological characteristics of these discontinuities have raised speculations related to their origin, be it related to mechanisms of bulging, cambering or to some tectonic or primary geological event.Several geologists and engineers from the northern hemisphere including Terzaghi already showed to be concerned with their role in granite foundations while in the southern regions Brazilian authors have found similar occurrences but also affecting individual lava flows of continental flood basalts in the foundations of major dams of the Parana Basin, which they designated under the particular name of “fault-joints”. This double-standard designation is self-explanatory of the difficulties involving their origin and related geomechanical properties: faults or just shear joints?Recently, similar features were encountered in the foundations of large dam constructions in anorogenic granites inserted in the realm of the Brazilian Amazon, where some of these discontinuities exhibit features common to tectonic thrusting combined with deep tropical weathering.The evidence of preshearing along the surfaces of such fractures, also associated to products of deep weathering, reduces their geomechanical strength substantially, suggesting values of ultimate phi spanning 12 to 28°. The detection of these descontinuities during initial investigation phases continues to be a major complex task in geological risk evaluations surveys. Trenching associated to some geophysical exploration techniques, although considered to be very basic exploration techniques are still the suggested methods for their forecast and previous determination."

Jan 1, 2015

By D. H. Wilton, C. I. Godwin, A. J. Sinclair

"A computer-based drill core logging system used to examine computer-based drill core logging system used to examine copper mineralization hosted in volcaniclastic rocks at the Sustut deposit, in north-central British Columbia, has many advantages over conventional logging. A relatively simple format for recording geological information allows complex, but significant, geologic parameters to be recorded consistently, accurately and quickly. This allows graphical presentations and statistical interpretation of the data that lead to rapid and detailed analyses of the control and distribution of copper mineralization at the Sustut deposit.Ore mineralization is concentrated in lens-shaped bodies and is zoned from native copper cores through chalcocite, bornite and chalcopyrite to a margin containing pyrite. Chalcocite, the principal mineral, occurs mainly in volcaniclastic agglomerate characterized by a specific grain size, a narrow range of matrix and fragment proportions, and a specific sorting.IntroductionWe report here a case history of the practical application of a detailed computer-based drill core logging system applied to the Sustut copper deposit of Falconbridge Nickel Mines Ltd. The Sustut deposit, containing a few tens of millions of tons of ore grading slightly more than one per cent copper (Church, 1975), is in north-central British Columbia about 875 km north of Vancouver. The deposit is contained in volcaniclastic sedimentary rocks of the Upper Triassic Moosevale Formation, which is within the upper part of the Takla Group (Monger and Church, 1977) of basic volcanic and associated sedimentary rocks. Takla rocks occur along the eastern fringe of the Intermontane Belt in the Canadian Cordillera (Sutherland Brown et al., 1971). The deposit consists of concentrations of copper sulphides, native copper and pyrite within pods and lenses parallel to bedding in the host sedimentary rocks. These sheet-like deposits exhibit a mineral zoning from pyrite at the fringes successively through chalcopyrite, bornite and chalcocite to native copper at the core (Wilton, 1978; Wilton and Sinclair, 1979)."

Jan 1, 1980