Search Documents

By A. Supomo, H. Resendiz, C. Burbidge

"Freeport-McMoRan Inc. (FMI) commissioned the expansion of the Morenci Metcalf concentrator in 2014. The concentrator included many design and equipment innovations, including the first-of-its-kind Metso Hydraulic Roll Crusher (HRC), variable speed ball mills and variable speed crushers. In addition to the innovative design, FMI commissioned the Metso APC team to design a realistic process simulator and the plant APC. The process simulator was utilized to train operators before commissioning, which led to a smoother plant start up. The plant APC utilized the concept of dynamic constraint control, which controls the feed to the primary ball mills by “pulling” the tons from crushed rock storage bins, which then automatically are filled by the upstream HRC and secondary crushing circuits. The primary ball-mill control also adjusts the water addition to the cyclone clusters to avoid overload and achieve sufficient grind size. The constraints include in-circuit constraints for feeder capacity, screen-deck capacity, ball mill power, cyclone mass flow, pump capacity and pump motor capacity. The APC system was implemented shortly after the start of commissioning and immediately demonstrated increased throughput and an ability to highlight and quantify process constraints and bottlenecks. The following paper outlines the control strategy, discusses system implementation, results and challenges.INTRODUCTION The FMI Metcalf Concentrator is located in Morenci Arizona on the site of the old original Concentrator. The new Metcalf concentrator started operation in May of 2014. This plant was designed for an average of 63,500 tpd (70,000 stpd), increasing the total Morenci concentrator complex production to a nominal 113,400 tpd (125,000 stpd). The process flow diagram is shown below in Figure 1.The process consists of primary crushing feeding a coarse ore stockpile followed by secondary crushing operating in closed circuit with vibrating screen decks. The screen undersize feeds the first of its kind Metso hydraulic roll crusher (HRC) operating in a closed circuit with vibrating screens. The primary crusher is a Metso 60x110 gyratory crusher. Secondary crushers are Metso MP1250 Crushers with variable speed drives. Secondary crusher discharge is recycled to the dry screen feed bin and screened with oversize returning to secondary crushing and undersize feeding the Metso HRC3000. The product from the 3.0 meter X 2.0 meter roll crusher is wet screened with the undersize feeding the grinding circuit, which is comprised of two each 24-foot diameter by 40- foot-long variable speed ball mills running in parallel with each in closed circuit with a cyclone bank of 12 cyclones. The wet screen oversize is recycled to the HRC feed bin."

Jan 1, 2019

By MaryAnn E. Crichton, David G. C. Clarry

"Environmental risk is becoming more important in debt and equity financing decisions in the mining industry worldwide. Demonstration of good environmental management practices and management systems has a direct impact on the ability of mine developers, operators and investors to raise financing. Based on experience in providing due diligence services, there are a number of factors that are important in assessing financial risks related to environmental issues in either new projects or existing facilities. A frame-work for understanding the importance and priorities of each element of environmental management is presented.IntroductionIn the context of lending money to a corporation, environmental issues represent another aspect of credit risk (Henry, 1989). These issues, because of their nature, represent the potential for large unforeseen expenditures if they are not known or acknowledged and are not being proactively managed. Lenders, other investors and their advisors, are becoming increasingly aware of the potential financial impact of environmental issues. Consequently, they are increasing their requirements for environmental audits to review the environmental issues, management practices and systems when they are considering financing mining and/or metallurgical processing operations worldwide.Many banks have signed the United Nations Environment Program (UNEP) Statement by Banks on Environment and Sustainable Development. Banks in this category include National Westminster Bank, the Union Bank of Switzerland, Deutsche Bank, and the Royal Bank of Canada."

Jan 1, 1997

By Michael Boyle, John Zeni

"The Blind shaft boring method is a mechanised process of excavating large diameter vertical shafts downward from the surface. It is a rotary drilling technique eliminating any requirement for personnel to enter the shaft or access underground workings during drilling and lining phases. Excavated material is delivered to surface carried by a flow of circulating fluid through the centre of drill rods. The drill assembly is suspended from a large A-frame rig and powerful winch at ground level providing vertical thrust to a hard rock cutter head. INTRODUCTION The Southern Coalfields Ventilation Shaft was constructed at a mine, 45 km north-west of Wollongong. The 5 m finished diameter (6.2 m drilled) shaft reaches a final drilled depth of 517 m, the deepest, fully lined blind bored vent shaft to date in Australia. Operated by a mining company in the Southern Coalfields, the expanding mine required a new ventilation shaft and associated surface infrastructure to service future operations. An assessment of future ventilation requirements for the coal seam operations identified a need to improve the capacity and reliability of the existing underground ventilation system in order to ensure a safe and efficient underground working environment. Installation of the new upcast ventilation shaft was determined to be the most cost effective and reliable solution to provide adequate ventilation for underground operations. The completed shaft is smooth and fully lined with steel/concrete composite liners that are hydrostatically sealed. The shaft lining is designed to meet the mine ventilation requirements for a service life of 20 years. The shaft intersects the top of the working section of the coal seam at approximately 513 m of depth. This includes the shaft collar depth and shaft bottom profiled intake section.PROJECT METHODOLOGY AND INDUSTRY BEST PRACTICE The shaft was drilled using the blind bore method, an innovative construction technique and an alternative to the traditional methods of sinking deep and large diameter shafts, such as raise boring and conventional drill and blast shaft sinking. The blind bore method allows the shaft to be drilled from the surface down without anyone having to enter the shaft or the mine during the construction process. This is by far the safest method of shaft construction and is especially suitable for difficult ground conditions where there may be unstable or water-charged strata. As this method involves drilling from the surface downward, shafts can be completed ahead of the underground mine development. Thus, allowing underground operations to focus on development and production without the conflicts of managing ventilation priority for underground contractors and mucking out spoil from excavation workings."

Jan 1, 2019

By Graham Farquharson, Jame Marshall

"Mining towns have always been an important part of Canadian geography. Many Canadians grew up in them. The frontiers of northern Canada would be a lot closer to the United States border but for the pioneering of new mines, new towns, and new transportation routes. Names such as Labrador City, Chibougamau, Val d’Or, Rouyn-Noranda, Kirkland Lake, Timmins, Sudbury, Red Lake, Thompson, Flin Flon, Yellowknife, Whitehorse,Trail and Kimberley are some of the better known larger communities that have grown to become major commercial and government centres, but which started as the base for a mining development.Many other smaller towns never grew beyond being small communities, dependent upon the local mine and many of these are still alive, but perhaps not quite what they used to be. In this list would be Buchans, Schefferville, Chapais, Cadillac, Virginia town, Lynn Lake, Uranium City, Pine Point, and Keno Hill.Nevertheless, all these towns and dozens more like them were residential communities where people lived and raised families and were quite accustomed to being days from the major centres of Montreal, Toronto, Edmonton and Vancouver, and not just hours away as wet end to measure travelling time today."

Jan 1, 1996

By E. Peek, L. Becze, K. Reading

"Gallium oxide is an important semiconductor material used in optoelectronic devices (flat panel and solar cell) catalysts and sensors. One of the methods to produce ?-Ga2O3 is the so-called hydrothermal route. It is practiced by Neo Gallium Compounds and comprises of two steps: (1) the production of mainly gallium-oxy-hydroxide in a pressure vessel by reacting metallic gallium with water at 200-220 ºC and (2) the calcination of gallium-oxy-hydroxide at 700-750 ºC to convert it into ?-Ga2O3. This paper describes this pressure hydrometallurgy process supported with relevant thermodynamic data and presents the characteristics of the ?-Ga2O3 powder produced for commercial purposes. INTRODUCTIONGallium is a relatively new metal, having been predicted by D. Mendeleev in 1871, discovered by P.E. Lecoq de Boisbaudran in 1875, and first commercially produced in the USA in 1943. Gallium is not rare, being more abundant in the earth crust than antimony, bismuth, molybdenum, silver and tungsten. However, few gallium minerals exist in nature, and the dispersion of gallium within other minerals add to the complexity of its recovery. In practice, gallium is found in dispersed state primarily in bauxites and in some sphalerites, and, to a much smaller extent, in some coals. At present, a very large proportion of the primary gallium in the world is recovered as a by-product of aluminum plants, mostly Bayer plants, where gallium is extracted from a bleed of the Bayer liquor (Roskill, 2011). In 2011, world production of primary gallium was estimated at 200 metric tonnes. In addition, there is a significant contribution of recycling to the overall yearly availability of the metal.Gallium exhibits fairly remarkable properties: it is liquid above 29.76 ºC, can be supercooled, and with its high boiling point (2204 ºC), is the metal with the widest liquid range. Gallium is magnetic, and is an excellent conductor of both heat and electricity. Gallium also displays a marked anisotropic electrical conductivity (Roskill, 2011). All these properties render gallium almost irreplaceable in the semiconductors (GaAs, GaN, GaSb, GaP wafers) and the optoelectronics industry (flat panel, solar cell)."

Jan 1, 2012

By Al Gagnon

Since start-up in 1972, many circuit problems have been encountered, most of which were related to the abundance of fines (-28 mesh), which the circuit had not been designed to treat. The major problems associated with the original circuit included excessive loss of magnetite, reduced throughput during periods of a high proportion of fine coal in the plant feed and low yield in the fine coal circuit. This paper outlines the coal processing circuit at Fording Coal Limited as it exists today, with emphasis on the changes to the original fine coal treatment circuit.

Jan 1, 1978

By A. Welty, T. Garn, K. Lyon, B. Jakovljevic, R. S. Herbst, M. Greenhalgh, Cytec Solvay Group

"Industrial rare earth separation processes utilize PC88A, a phosphonic acid ligand, for solvent extraction separations. The separation factors of the individual rare earths, the equipment requirements, and chemical usage for these flowsheets are well characterized. Alternative ligands such as Cyanex® 572 and the associated flowsheets are being investigated at the pilot scale level to determine if significant enhancements to the current separation processes can be realized. These enhancements could be defined as higher separation factors, reduced stage requirements, or reduced chemical consumption. Any of these enhancements can significantly affect the costs associated with these challenging separation proccesses.A mid/heavy rare earth element (REE) separations flowsheet was developed and tested for each ligand in a 30 stage mixer-settler circuit to compare the separation performance of PC88A and Cyanex® 572. The ligand-metal complex strength of Cyanex® 572 provides efficient extraction of REE while significantly reducing the strip acid requirements. Reductions in chemical consumption have a significant impact on process economics for REE separations. Partitioning results summarized Table 1 indicate that Cyanex® 572 offers the same separation performance as PC88A while reducing acid consumption by 30% in the strip section for the mid/heavy REE separation."

Jan 1, 2016

By O. Babak, J. G. Manchuk

ABSTRACT A significant factor in evaluating bitumen recovery from an oil sands mine is the particle size distribution (PSD). Increased understanding of mined ore quality and improvement in predictions of recovery can be achieved through PSD modeling. This paper addresses PSD modeling using geostatistics. PSDs may be described using many discrete particle sizes, making this a challenge. The approach parameterizes PSDs with a few statistics. A lookup table is used to reconstruct the PSDs based on models of the statistics. The workflow is applied to Total E&P Canada’s Joslyn Lease and yields good results that reproduce input statistics without introducing artifacts.

Jan 1, 2013

By Cindy Schiewek

Industrial injury occurrences are an ongoing concern for Mine Operators. Along with the personal suffering of injured workers comes an increase in compensation and productivity costs. Growing recognition of repetitive stress and bodily injuries, accompanied by recent studies, validates the assumption that a relationship exists between ergonomic injuries and machine design. Intuitively, there is a belief that an ergonomically designed machine will reduce repetitive stress injuries through design and education however; quantifying this belief has been a challenge for Mine Operators. Sandvik Tamrock has undertaken a project aimed at developing a business model to assist in quantifying the benefits of ergonomic intervention. This model focuses on distinguishing and quantifying this method of intervention to allow for a better evaluation of the machine. For simplicity, the project initially focused on the Face Drill Jumbos. The target of the project was three fold: !" Recognition of the cost drivers for compensation; ergonomic injuries !" Identification of the relationship between ergonomic machine design, and the decrease of the negative effects associated with the cost drivers !" Systematic prioritization for ?prevention by design? The project findings substantiate the expected reduction in injuries and compensation claims. Based on all ergonomic intervention studies conducted, each case showed a reduction in compensation cost; through prevention by design, one can reduce the amount of potential risk. The paper addresses the resources and methodology used, along with the findings and its relevance to the issues that face the Mining industry.

May 1, 2003

By Guy Demers

"This paper defines the responsibilities and functions of the Maintenance Department, and its organization, physical and human assets, highlighting the unique operating problems. Due to the self-sufficient aspect of the Asbestos Hill Deception Bay project, the Maintenance Department cover-s fields that are numerous and very dissimilar: production, mobile, processing, service, power generation, fire protection, heating, water and sewage disposal equipment. Added to this, buildings, plant and camps, wharves and communications equipment all demand versatility, adaptability and expertise from maintenance personnel. Good maintenance practices are a necessity in this environment and are more critical than at southern locations; that is, high-quality replacement material, complete and well-controlled preventive maintenance, major repairs on a component-replacement basis, updated inventory, efficient training and permanent contacts with suppliers, combined with an equipment improvement program, updated specifications on lubricants, hoses, seals, filters, etc., are mandatory. The seasonal aspect of the operations applies a great deal of pressure on the maintenance team, as the production months do not permit major repairs. Short- and medium range planning and accurate evaluation of equipment conditions highly influence production efficiency. Maintenance control, planning and scheduling do not follow the accepted standard routines, as personnel turnover normally does not permit an accumulation of knowledge of the equipment history and condition by the •individual tradesman."

Jan 1, 1976

By Dan Miners

"This presentation will provide an overview and understanding of Mine Safety and Health Administration (MSHA) and Ontario Regulations for Mines and Mining Plants. It includes discussions on the history and practical development of the standards and an overview of engineering best practices from a construction, maintenance and operational viewpoint. INTRODUCTION Ontario is one of the safest mining jurisdictions in the world and has some of the most comprehensive regulations for the construction, operation and maintenance of a mine. In the USA, several operators have adopted some or all of the practices prescribed by the Ontario Regulations as an internal procedure. Experience has demonstrated that these plants are indicating less unplanned downtime and fewer issues with MSHA inspectors in their hoist plants. HISTORY AND THE REGULATIONS Both Canada and the USA have had some form of laws governing the operation of mines since the late 1890s. The paths of legislation have run in reasonably parallel lines, continually improving the health and safety conditions in the mining industry. Ontario Mine Health and Safety In the 1970s the accident rates in mining were higher than any other industrial sector; this prompted a Royal Commission on the Health and Safety of Workers in Mines (the Ham Report). The recommendations of this report, published in 1976, generated several changes in the regulations regarding worker safety in mines. Following the release of the Ham report, the Occupational Health and Safety Act (OHS) was passed by the Legislature in 1978. The Act is a set of comprehensive laws governing almost all Ontario workplaces, and it replaced separate laws governing different industrial sectors. OHS is enforced by the Ministry of Labour (MOL), and this discussion will focus specifically on Ontario’s Occupational Health and Safety Act, R.R.O. 1990, Regulation 854, Mines and Mining Plants, Part X Mine Hoisting Plant (Ontario Regulations). USA Mine Health and Safety A coal mine explosion in West Virginia and medical studies on occupational disease led to the 1969 Federal Coal Mine Health and Safety Act (Coal Act). The Coal Act was the most comprehensive and stringent Federal legislation governing the mining industry to date. The Mining Enforcement and Safety Administration (MESA) was formed, following the 1973 Act, as a new departmental agency to assume the enforcement of safety and health in mines. The Federal Mine Safety and Health Act of 1977 (Mine Act) transferred enforcement responsibilities from the Department of the Interior to the Department of Labor and named the new agency the Mine Safety and Health Administration (MSHA). This agency enforces the Code of Federal Regulations (CFR), and this discussion refers to CFR Title 30 Mineral Resources, Chapter I Mine Safety and Health Administration, Department of Labor, Subchapter K—Metal and Non-metal Mine Safety and Health (MSHA)."

Jan 1, 2019

By Yuyong Li, Liangman Zhang, Zhaolian Wang, Shun Wang, Ltd. Shandong Huate Magnet Technology Co., Fengliang Liu

"Introduce a newly revolutionary magnetic separator - Raising Concentrate Grade and Decreasing Dregs Content Magnetic Separator Series JCTN (i.e. RCG&DDC MS JCTN). HUATE® JCTN is designed for rinsing, purification, desliming and thickening of the magnetic minerals as per different requirements. Adopting 240°-270° larger magnetic element with multi-poles and magnetic pulsation, and combining the devices of multi-channel rinsing water and top flushing water and new style tank, HUATE® JCTN can improve another 2%-10% concentrate mFe% than the traditional MS without lowering the concentrate recovery rate. Thereby, it solves the uneasy concentrate upgradation problem of the traditional MS resulting from the magnetic aggregation. Now, JCTN has been successfully applied in more than 30 mines in Australia, China and Russia, e.g. Sino Iron of CITIC PACIFIC MINING MANAGERMENT PTY LTD. HUATE® JCTN can optimize the industrial processing line by: 1) improving the discarding rate before milling to discard the necessary tailing ASAP; 2) getting in advance the final concentrate after milling. One JCTN can replace many traditional MS in series. In some way, it can also replace the anti-flotation separation process.INTRODUCTIONWe’re writing to introduce a newly revolutionary magnetic separator - Raising Concentrate Grade and Decreasing Dregs Content Magnetic Separator Series JCTN (i.e. RCG&DDC MS JCTN). HUATE® JCTN is designed for rinsing, purification, desliming and thickening of the magnetic minerals as per different requirements."

Jan 1, 2016

By Azadeh Riahi

The main goal of this paper is to investigate the effects of permeability anisotropy in Large Open Pit (LOP) mines for problems that exhibit homogeneous anisotropic characteristics. The most important effect of the groundwater flow in open pit mines is on the stability of the pit slopes. This study will investigate the effects of having increased permeability in both horizontal and vertical directions on three aspects of LOP behavior, location of phreatic surface, pore pressure distribution and stability of slopes. The hydromechanical coupling is simulated using a one-way coupling approach. The Shear Strength Reduction method (SSR) is applied to assess the stability of slopes. The studies performed in this paper suggest that anisotropy in permeability leads to a significantly different regime of pore pressure dissipation depending on two aspects, ratio of anisotropy and the relative magnitude of permeability to simulated time. As a result, variation in safety factors and the location and depth of the failure surface must be expected.

Jun 1, 2012

By A. Aubin, H. Yang, G. Zaluski

The Athabasca Basin of northern Saskatchewan and Alberta is an exceptionally rich metallogenic region, hosting more than 2.8 B lb U3O8, of which over 927 M lb U3O8 have been mined out since extraction first started in the late 1970’s. A detailed compilation of several empirical features of 85 deposits located within the basin was conducted in order to understand the distribution and variability of the geological characteristics of the mineralization and its associated alteration. A new empirical classification was devised based on four parameters: 1) geometry of the mineralization (dimensions and relation to the unconformity surface), 2) size, grade and metallurgical complexity of the mineralization, 3) lithostructural setting, and 4) extent and nature of associated alteration haloes. This compilation defines the footprint characteristics of the Athabasca Basin deposits, which guides decision-making processes from early exploration and discovery to resource expansion and extraction.

Jan 1, 2020

By A. Bezama

For over a decade European countries have addressed contaminated sites by developing technologies for managing both polluted soil and groundwater. This development has not only been driven by health and environmental aspects, but also because of economic pressures, as the remediation and redevelopment of derelict areas can be a meaningful alternative to undeveloped areas for the establishment of new industrial, recreational, housing and service locations. In most developing countries, however, the subject of contaminated sites is a new environmental issue that authorities have recently started to deal with. Among these countries, Chile has just started to prepare the country's legal context as well as to foster the formation of research and investigation groups that will deal with the exploration, investigation and management of contaminated sites. That requires a comprehensive technical, scientific and legal support in this stage. Goal of this article is to present the state-of-the-art technologies for site remediation currently applied in industrialized countries, in order to identify the most interesting approaches that can be implemented within the Chilean situation, especially considering the influence of the copper mining industry on the soil and groundwater quality of the environment surrounding their production facilities.

Jan 1, 2007

By F. L. Thompson

MAN has been using lubricants of one type or another for at least four thousand years, and probably for a much longer period. We have learned from the inner wall of the tomb of Tehuti-Hetep, on which is a decoration illustrating the method of moving a great stone statue, that as early as 1650 B.C. lubricants were used to facilitate the movement of heavy loads. The Egyptians had available nearly every animal oil and fat, as well as at least thirteen vegetable oils, of our time, all used for food products and in the arts. Examination of the deposit on the axle of a chariot from an Egyptian tomb of 1400 B.C. showed it to consist of animal fat, quartz, sand, iron, and compounds of aluminium and lime-indicating a manufactured lime-soap grease made with lime-soap and possibly tallow. This would not be a bad lubricant for the axles of chariots which had to travel over sandy soil in hot weather. As to the method of grease application, it is remarkable that, from the time wheels were first used in the far distant past up to the present day, no one has ever thought it necessary to design a seal to keep the lubricant in and the dirt out. While time certainly marches on, we have today, in waggons throughout the world, exactly the same form of lubrication as was used in the earliest chariots. From the early days of the chariot until shortly before 1800 A.D. (when the steam engine was introduced), the main heavy equipment required for mining purposes, for machines of war, etc., was made of wood. The bearings were rough, but usually they had metal in the lower half. Light machinery was made of bronze, brass, or iron. Large clearances and poor alignment, plus the fact that speeds were much below present-day demands, combined to provide conditions that were quite satisfactorily met by the lubricants available. These were often produced locally by the machine operator. In northern countries, lard oil, prepared from the fat of hogs, was the universal lubricant employed in machine shop, as a belt and leather dressing, and for cutting operations. Sperm oils were used for light machinery, whereas beef and mutton tallow were more generally employed for the largest bearings. For the early steam cylinders, a slug of heated beef tallow was injected wherever the cylinders gruntingly complained of a lack of lubricant. Southern countries, however, resorted to the use of vegetable oils-olive, cocoanut, etc.

Jan 1, 1940

By R. F. Baxter, C. M. Read, R. I. McCulloch

"Globalization of the aluminium industry continues to increase the pace of change and the intensity of competition, while simultaneously, society demands better products, cleaner technologies and sustainable industries. Bechtel, a global engineering, construction and project management company, is not immune to either the opportunities or the challenges created by globalization. However, and not withstanding the challenges, for aluminium industry ""players"" with a true global perspective, globalization presents very real opportunities that may be leveraged to deliver value creating goods and services. The following paper will focus on the exploitation of one of the opportunities created by globalization in the Knowledge Management domain - the application of high level tools and methodologies to improve global delivery of greenfield and brownfield aluminium smelter construction projects. Specific examples will be presented of value driven solutions that were delivered at the early stages of project engineering."

Jan 1, 2006

By J. L. Miller, R. W. Burns

This paper sets out the various phases of bringing a merchant bar mill into operation from feasibility consideration through financing, design and scheduling to completion.

Jan 1, 1967

By Chas. L. Emery

"The laws of rock mechanics apply equally well to all rock structures, and open pits are not exceptions. The concepts and some arguments about the emphasis to be placed on various aspects of open-pit design are discussed in this article.RocksROCK can be described as a granular material consisting of grains and glue. The grains may be fragments of other rocks or polycrystalline aggregates. The glue may be ferruginous, calcareous, argillaceous, siliceous or other material connecting the grains. In a crystal intergrowth, the outer layers of the crystals in contact with each other may be considered to act as a glue. Water may be a glue in clay or a grain in a crystal structure. Air and other fluids or gases are grains if they occupy spaces in a granular mass. Such grains are functional either chemically or mechanically or both."

Jan 1, 1966

By S. C. Radopoulou

Pavement condition assessment is an indispensable constituent in maintaining roadway infrastructure. Current practices for pavement condition assessment are labor intensive which introduce subjectivity in pavement rating and are time consuming. Automated methods rely on full 3D reconstruction of the pavement surface which introduces high equipment and computation costs. This paper presents a methodology for detection of patch type distresses in asphalt pavement images. This method uses filtering and histogram equalization for clearing and enhancing the image accordingly. It continues by applying the morphological process of closing, along with some rules based on the characteristics of a patch when captured in an image, to finally detect the area it occupies. Criteria for area, length, and width of a patch as seen in an image are taken into account to decide whether a probable patch is actually a patch. The method has been implemented in C#. The preliminary experiments demonstrate it produces promising recognition results

Aug 1, 2013