Search Documents

By S. M. Bulatovic, D. M. Wyslouzil

"This paper presents the results of a study of the effect of flowsheet configurations on metallurgical results and describes a general method for developing and optimizing flowsheets used in the treatment of massive sulphide ores. The flowsheet configuration can have a significant effect on recovery and selectivity between valuable minerals and gangue minerals. Placing of intermediate products within the flowsheet, positioning of various pretreatment units, such as conditioners or regrinding mills, and the ability of the flowsheet to cope with wide swings in the feed grade and composition are the major parameters that determine the optimum flowsheet configuration. The complexity of the flowsheet is largely a function of the ore itself and of the number of final, marketable products that have to be recovered from the ore. INTRODUCTIONTechnological ExpansionThe trend of past decades has been towards larger equipment and a better understanding of the chemistry of the flotation process. Despite appreciable progress in these areas little attention was given to the study of the actual configuration of the flowsheet, although the arrangement of the flotation equipment significantly affects the overall performance of the circuit."

Jan 1, 1989

By R. A. Triglavcanin

Delivering dilution water and mixing this water with incoming feed slurry, addition of flocculant, maximising flocculant-slurry interaction to build aggregate size, unabsorbed flocculant percentage, volume average of solids volume fraction, momentum dissipation ratio, dilution recycle ratio, volume average shear, maximum shear rate at exit, aggregate size on exit, uniform discharge profile and more ? all of these need to occur in the right order and in the right proportions within the thickener feedwell, the secret to thickener performance.

May 1, 2009

By Carlos Antônio de Morais, Renata Dias Abreu

The present work describes a study of the separation of terbium and dysprosium from heavy RE concentrate through a solvent extraction circuit in a counter-current system. As the efficiency of the REE extraction by acid extractants rises with the increase of the atomic number of the element, the aim of this work is to extract the elements with higher atomic number maintaining Tb and Dy in the aqueous phase. Thus, terbium was separated first with subsequent separation of dysprosium. The experiments were carried out by using IONQUEST®801 as the extractant and a REE-hydrochloric liquor as feed solution. The optimum operational circuit in terbium separation was comprised of 37 stages: extraction, scrubbing, stripping, and solvent washing. For the dysprosium separation 39 stages were required. Terbium separation over 92% with over 95% purity and a Dy separation over 97% with over 95% purity were obtained.

Jan 1, 2014

In this paper, the use of electrochemical AC impedance spectroscopy (EIS) for in-situ diagnosis of high temperature PEM fuel cells is described. EIS was performed on single cell hardware, built in-house, using a fuel cell test station modified to operate up to 120°C and 30 psig. Electrode kinetics, membrane resistance, porous-layer and mass transport impedance of MEAs, assembled in-house, were measured at various current densities for the purpose of validating the test station and cell hardware, and for optimizing MEA and flow-field designs. The effect of temperature and humidity on the various impedances was investigated. Impedances obtained at lower and higher temperatures were compared to obtain insight into the issue of water management in operating fuel cells.

Jan 1, 2005

By David L. Sprott

This paper presents an evaluation of underground-to-surface haulage options for a relatively large deposit. Specifically, it presents a recommended haulage option to provide the greatest value to the Project. Options considered included conventional truck, trolley-truck, conveying and shaft hoisting. The work was done at the level of a preliminary assessment as input to an internal pre-feasibility study. The Base Case for the analysis in this study was a Long Hole Open Stoping option (LHOS) using conventional truck haulage. Two scenarios were considered for the evaluation and included: 1. The current resource to ~700 m depth. 2. An expanded resource to ~825 m depth. The haulage options evaluated included three trucking options, three conveyor options and two shaft options. The paper presents the results from evaluating these options within the two mining scenarios using a Discounted Project Cost (DPC) comparison. Recommendations are made for the options that will provide the greatest overall value to the project.

May 1, 2008

By Michael Davies

Mined Material Management Meeting or Missing the Mark? o you agree that we have the technology to consistently design robust M3 facilities? ?YES your experience do these M3 facilities perform as expected during operations? ?USUALLY hat can be done to improve performance, e.g. better communications between project and operating teams, discontinuity between design and operational input by designers, others? ?UNDERSTANDINGWHY THINGS GO WRONG an we identify the key characteristics of ?good M3 facilities?, i.e. ones that are performing well? Can we identify ?good M3 facilities?, i.e. ones that perform well and can be held up as examples? ?WITHOUT QUESTION?? your opinion, for what reason do they not perform as expected? ?NO SINGLE REASON??..

May 1, 2010

By C. O. Aksoy

Operating the underground marble quarries effectively, it is important to evaluate the deposit blocks economically which are affected by the suitability of the topography and configuration of bedding. The joint sets within the deposit and the spacing between these discontinuties are also of great importance. In this study, the marble deposits that could be geomechanically eligible for underground excavation have been selected throughout Turkey and these selected reserves have been classified accordingly by Q-Rating System. These classified marble deposits that forms groups of 1,2, and 3 (groups were determined by evaluating the O-rating, topography, quarry situation, cracks, joints etc.) are convenient for this type of production. Nevertheless, when the auxiliary factors (topography, location, production method etc.) regarding the deposit have also been investigated, the most convenient sub-group of deposits (Afyon Tiger Skin, Burdur Beige, Diyarbakir Pink and Mugla White) have emerged. The sizing of the pillars have been performed utilising Bieniawski?s stress profile. The LAMODEL software, developed by National Institute for Occupational Safety and Health (NIOSH), USA and run under the laminated displacement discontinuity method, has been used to size the pillars. This work brings in a novel opportunity to Turkey, in which no underground marble quarry has been attempted up-to-date similar to its several examples in Italy, USA, etc. This study serves as a reference for the marble operators and for the pioneering application of laminated displacement discontinuity method in hard rocks.

Apr 1, 2005

By C. A. Young

"The stabilization of tailings has been a matter of concern to the Mining Industry for many years. In earlier times, when mines were small and only high grade ore deposits were mined, the problem was not a great one. But, more recently - during the last 30 to 40 years - the increased world demand for various metals, combined with the vast strides that have been made in the improvement of metallurgical extraction processes, have resulted in the development of lower grade ore bodies.About 30 years ago The International Nickel Company started experiments to stabilize the surface of the tailings and prevent them from becoming a dust source under certain weather conditions. The use of chemicals to form seals, covering with crushed stone, mulching with straw and some early seedings were some of the stabilizing methods tried. Results were either unsuccessful or impractical economically.In 1954 a series of experiments to establish vegetation on the tailings began. Varying degrees of success were achieved but however unsuccessful a particular scheme turned out, the attempt to find a solution was never written off. As we look back, we realize that the first significant break-through came as the result of three test plots planted in the spring of 1957. Each plot covered an area of approximately one-third of an acre. One plot was successful and persisted until it was covered up by the expansion of the tailings area in 1961.In 1960 a review of all our test plots to that date was carried out to assess the factors which effect the chance of grass being established."

Jan 1, 1969

By L. Kilpinen, K. R. Kay, H. B. Fowler

"FOREWORDThe International Nickel Company of Canada has built four ore concentrating plants since 1950. The fifth and largest is now under construction. In each successive plant, the level and type of instrument control and sophistication of control techniques have increased as experience was gained. The type of control progress is illustrated in Fig. 1.At Frood-Stobie the high degree of instrumentation and the level of control were made possible by the constant evolution of techniques and improved instrument hardware technology. We have established in practice concepts that are sound, although many modifications to instrument sensor types and locations 1-rere often necessary. It is generally true that at other existing Inco mills, it is possible to run ""all manual"" for protracted lengths of time because of operator availability and dependence. The Frood-Stobie Mill is the exception, and it is the degree of reliability of the instrumentation hardware and level of maintenance that has made this possible."

Jan 1, 1971

By J. P. Mogan, E. D. Dainty

Polynuclear aromatic hydrocarbon (PAH) levels were measured in underground mines in the vicinity of diesel vehicles equipped with several types of emission control hardware. In general, the emission control devices appeared to reduce PAH levels, but the companion mutagen study suggested that the reduction might not always be beneficial. All underground PAH concentrations were below the threshold at which a significant impact on health might be expected, but recent animal exposure studies have indicated that PAHs may not be the primary hazard from chronic diesel fume exposure.

Jan 1, 1994

By J. Gillies

"Extraction of Gold in Ketone from a suitably prepared sample of sulphide or siliceous ore or concentrate permits a rapid and accurate determination by Atomic Absorption. Mill test products and exploration development samples are acid-treated to effect complete dissolution of silver, copper, zinc, lead, molybdenum and iron present. Interferences in the determination of molybdenum are described. Results by Atomic Absorption are comparable to those afforded by other acceptable methods.INTRODUCTIONDuring recent years much has been written and discussed concerning Atomic Absorption Spectrometry as a technique for determining the concentration of metallic elements. We would, however, recommend a perusal of the paper presented by J. C. Ingles at the annual meeting of Canadian Gold Metallurgists held in Ottawa, January, 1966. The paper was published in the August, 1966, issue of the Canadian Mining Journal, and contains general information on Atomic Absorption.The purpose of our paper is to present certain specific method procedures for the determination of several precious and base metals normally present in Mine, Mill and Smelter products. Of necessity, analytical results should be as accurate as the most suitable available method permits, whether for metallurgical balance, settlement purpose, ore beneficiation programs, or exploration property development. The success of such programs is relative to the accuracy, speed and economics of the analysis. It is obvious, therefore, that in presenting our paper we consider the technique has achieved the desired evaluation."

Jan 1, 1968

By Robert B. Parsons

"The February 18, 1987, Federal Budget contains a proposed amendment which would simplify somewhat the ""successor corporation"" rules in the Income Tax Act. Despite this amendment, though, the important successor rules will continue to be relatively complex.IntroductionThe February 18, 1987, Federal Budget papers propose an income tax amendment whereby the so-called ""successor corporation"" rules would be revised by removing the present provision which limits the application of these rules to a maximum of two ""successions"". The successor corporation rules represent one of the most complicated sets of rules in the Income Tax Act. This month, Tax Notes seeks to explain these rules and the proposed amendment in simplified terms.Basically, the successor rules provide a mechanism for transferring unused exploration and development expenses from one taxpayer to another , in specified circumstances. The aforementioned limitation of two successions refers to the rule which allows a maximum of two such transfers with respect to any particular pool of deductions."

Jan 1, 1987

By Ron Hatch, M. K. Witte

"INTRODUCTIONThe proper selection of carbon for a gold carbon in pulp (CIP) circuit involves careful evaluation of several physical, chemical and economic factors. A series of evaluations are required to maximize gold recovery at the lowest capital and operating costs, whether the carbon is selected for an existing gold mill circuit or a new mill under design.Although evaluation may proceed through various stages, it is the intent of this paper to outline some of the preliminary testwork that should be carried out to screen potential carbons for a particular application.An examination of the specification sheets supplied by the various carbon manufacturers may indicate some desirable properties on which to make cursory selection. This exercise by itself will not provide the basic data needed for selecting the best carbon for a particular ore pulp and metallurgical circuit. The necessity of further metallurgical evaluation is indicated by the fact that different carbons perform differently depending on the physical and chemical nature of the leach pulp. In the case of an existing mill, actual leach slurries using mill water are available and should be used for testwork. In the case of new mills, leach pulps must be prepared to simulate the proposed circuit.Five coconut shell activated carbons were obtained from various suppliers, all reported to be 6 x 16 mesh carbons recommended for CIP circuits. A metallurgical evaluation was made utilizing two leach pulps with significantly different characteristics. This paper describes the test procedures utilized and the results obtained from the testwork."

Jan 1, 1985

By George P. Demopoulos

In this paper the author will provide an overview of over 20 years of research & developments in the area of hydrometallurgical arsenic immobilization that culminated recently in the industrial implementation of the atmospheric scorodite process. The paper will consider various aspects of arsenic fixation in the non-ferrous metal industry from the iron-arsenic co-precipitation process employed to arsenic-bearing effluent solutions; to autoclave processing of arsenical copper and gold feedstocks and the fate of the in-situ formed iron sulphato-arsenate precipitate phases; the precipitation and stability of scorodite; the possible stabilizing role of mineral phases like yukonite, and the development of "scoroditeplus" processes employing novel encapsulation strategies. Emphasis is placed on the characterization and long-term stability of the various forms of arsenic-immobilized phases under either oxic or anoxic conditions over a wide pH range and the establishment of critical links between process parameters and hazardous material stability, contributing thus to advancement of new generation safe and sustainable waste management technologies.

Jan 1, 2014

By Malcolm Powell

"Predicting the performance of the whole mining process is surely the holy grail of predictive simulation. This can be named ‘Integrated Process Prediction’.The objective is to be able to predict the response of the processing chain, from mining to concentration, to changes in the ore type. This can apply to greenfields design – selecting processing options to optimise the overall mine performance within the constraints and aspirations of the greater community and environment; expansion and optimisation of existing plant to deal with changes in economic drivers and ore types; and on-line control – predictive reaction to ongoing changes in ore processing types in an operation.In order to achieve this there are several broad key components that are required: ore characteristics based on in-situ rock properties; a reliable 3D map of the ore body by the key processing parameters; prediction of how the rock fragments and the energy requirement to break it; the ability to predict and track progressive mineral liberation of the rock through the reduction process; the response of rock to separation processes as a function of the rock mineralogical properties. This requires the identification of primary rock properties and associating them with the rock particles as they move along the mining process chain to a concentrate or various forms of waste.This paper looks at the value of this integrated approach; the challenges it poses; the technology and capability we require; and how as a mineral processing community we can address the challenges."

Jan 1, 2016

By Louise Laverdure

Outline ?Background ?Issues and considerations ?Why do we need to innovate ?Green Mining Initiative ?Footprint reduction ?Innovation in waste management ?Ecosystem risk management ?Mine closure and rehabilitation ?The Future

May 1, 2011

By Pierre Laliberté

Objectifs ?Quantifier les économies d?énergie potentielles liées àl?utilisation de différentes technologies ?Créer un modèle permettant d?évaluer les économies possibles d?énergie en combinant plusieurs technologies ?On ne peut simplement additionner les pourcentages d?économie individuels pour en évaluer le total.

Feb 1, 2008

By Jose A. Caceres

Mine planning and mineral processing optimization are usually treated as two unconnected problems, especially at open pit and panel caving mines where the cut-off grade is practically the only variable optimized and analyzed for in the planning proposes. Using existing planning tool, the output is a reserve consumption strategy privileging higher grades. With the earlier consumption of the highest grades, every year produces revenues which are closer to the cost and potentially even below cost. However, there are other ore characteristics that can also affect the profitability of the operation. A new methodology has been developed, incorporating the grinding and flotation relationship into the mining economic models for the simultaneous analysis and optimization of the throughput-work index-recovery relationship through changes in the mining limits, sequence and redefinition of the reserve consumption strategy. A mine-site that implements this new planning strategy, can expect to increase the NPV from 5 to 15% depending on the actual operational settings. Two case studies have been developed, showing how the inclusion of the work index in the economic model changes the phase and mining sequence in an open pit mine and the caving sequence and the optimum column height in a panel caving mine.

May 1, 2004

By R. Pérez, James A. Finch, F. Tavera, Cesar O. Gomez

"Gas holdup is a variable which affects the operation of flotation columns. On one hand, gas holdup is a function of bubble size (a function of sparger type, frother characteristics and concentration, and air flowrate), tailings flowrate, solids content, and mixing patterns in the collection zone. On the other, gas holdup defines flotation kinetics and carrying capacity. Therefore, gas holdup is a useful variable to control and diagnose the operation of a flotation column, but the lack of a reliable sensor for on-line gas holdup monitoring has prevented its use in industry.This work describes the principle and the practical difficulties associated with the development of a gas holdup sensor based on the measurement of the electrical conductivity of dispersions. Two different approaches have been devised. These approaches will be described and test results presented of prototypes in laboratory and industrial columns.Background.Several years ago, a research program was initiated at McGill to use electrical conductivity as the basis for developing sensors for process measurements in mineral processing. Electrical conductivity is an intensive property which is a function of the concentration of the different phases present in a dispersion. The initial focus was on the detection of the interface between two dispersions with different characteristics (i.e., that between the collection and froth zones in flotation columns or that between clear water and sedimented solids in thickeners). The technique works in this case by searching for the location at which a sudden change in specific conductivity occurs, as a consequence of different gas holdup or solids content, and absolute values of the specific conductivity of the dispersions involved are not necessary1,2."

Jan 1, 1995

By Jianglan Duan, Steve L. Cockcroft, Andre B. Phillion, Carl Reilly, Daan M. Maijer

"In the aluminum alloy wheel casting process, careful design of the cooling system in the die and its operation (cooling channel timing) are critical to achieve quality and productivity goals. The problem is challenging owing to the cyclic nature of the process and the relatively large thermal mass of the die in comparison to the wheel. For a given die geometry, a set of constraints have been defined to ensure directional solidification and an objective function, based on cooling rate during solidification, has been defined to reach a target secondary dendrite arm spacing. The methodology presented in this study employs the commercial finite element package, ABAQUSTM, and an optimization module based on the open source library, Scipy. The developed methodology has been applied to a series of geometries and cooling system configurations, including a 2-D axisymmetric wheel and die assembly generated from a prototype die. Preliminary testing has shown that careful selection of the objective and constraint functions have made it possible to reach desired solidification pattern.TM- Dassault Systèmes Corp."

Jan 1, 2014