Search Documents

By Karen Dawson

This paper presents a case study of the deformation-based design, construction, and performance of stone column ground improvement (GI) beneath a mechanically stabilized earth (MSE) wall and bridge abutment with heights up to 50 feet. As part of the widening of Interstate 5 (I-5) to allow High Occupancy Vehicle (HOV) lanes in Tacoma, Washington, a new approach and span over the Puyallup River will be constructed. During the soils investigation and design phase of the project, low plasticity silts (ML) inter- bedded with silty sand layers and organic silt where identified as being potentially liquefiable. Stone column ground improvement was designed using a deformation-based approach to address static settlement and seismic stability of the proposed MSE embankments. The deformation-based design of the stone columns resulted in significant savings over a limit equilibrium-based approach. This paper presents the results of sonic coring taken from the initial stone columns installed and compares these results to the real-time data acquisition reports from the stone column installations. Vibration monitoring results during stone column installation are included. Settlement monitoring at the face of the MSE wall and buried vibrating wire settlement monitoring elements are presented and compared to the original settlement predictions.

By James M. Tantalla, Roderic A. Ellman, W. Allen Marr, Scott R. Bamford

"Construction of the powerhouse for the Willow Island Hydroelectric Project required a 100-ft deep excavation inside the limits of a cofferdam and embankment-seepage cut-off wall through soil and rock adjacent to the Ohio River. Portions of the rock had preexisting weak plans and slickensided surfaces with low frictional strength. Stability analyses were performed for critical sections of the excavation to evaluate the stability of the soil slopes and rock cuts using buckling, tension crack, and limit equilibrium analysis techniques. Loading conditions included the 100-yr and intermediate floods, normal pool, sudden drawdown, and seismic design conditions.Stability analyses indicated adequate factors of safety for soil slopes and for rock cuts through the landside embankment sections. However, the results of deep-seated stability analyses through the rock supporting the riverside cellular cofferdam indicated unacceptable factors of safety. Consequently, the riverside portion of the excavation required measures to increase stability. Long, high-capacity rock anchors and deep dewatering wells to lower the site piezometric head were chosen for this purpose.Thirty high-capacity rock anchors were installed on the upstream, riverside, and downstream sides of the cofferdam rock cut. Required rock anchor loads varied from 1,968 to 2,074 kips. The designed anchors consisted of multiple, seven–wire strands with up to 59 strands per anchor. Bond lengths used an allowable bond stress of 100 psi based on the rock bond measured with pull-out tests. Maximum bond and anchor lengths were 50 ft and 140 ft, respectively. Measurements of forces in selected strands and displacements of the excavation showed excellent performance."

Jan 1, 2017

By Dominic Parmantier, Karen Dawson, Suthan Pooranampillai, Seungcheol Shin

"This paper presents a case study of the deformation-based design, construction, and performance of stone column ground improvement (GI) beneath a mechanically stabilized earth (MSE) wall and bridge abutment with heights up to 50 feet. As part of the widening of Interstate 5 (I-5) to allow High Occupancy Vehicle (HOV) lanes in Tacoma, Washington, a new approach and span over the Puyallup River will be constructed. During the soils investigation and design phase of the project, low plasticity silts (ML) inter- bedded with silty sand layers and organic silt where identified as being potentially liquefiable. Stone column ground improvement was designed using a deformation-based approach to address static settlement and seismic stability of the proposed MSE embankments. The deformation-based design of the stone columns resulted in significant savings over a limit equilibrium-based approach. This paper presents the results of sonic coring taken from the initial stone columns installed and compares these results to the real-time data acquisition reports from the stone column installations. Vibration monitoring results during stone column installation are included. Settlement monitoring at the face of the MSE wall and buried vibrating wire settlement monitoring elements are presented and compared to the original settlement predictions.IntroductionStone column ground improvement was implemented as a means of supporting mechanically stabilized wall approaches for a new bridge over the Puyallup River, part of HOV improvements to I-5 in Tacoma, Washington. The work discussed in this case history was part of the Washington State Department of Transportation (WSDOT) I-5/Portland Avenue to Port of Tacoma Road, Stage 1 Northbound HOV contract, developed as an early work element to a follow-on bridge construction project. The area requiring stone column ground improvement is shown in Figure 1. The improved ground supports permanent geosynthetic walls and embankments up to 50 feet high. This wall can be seen in Figure 1. The selected ground improvement primarily provides global stability of the soils beneath the walls during anticipated seismic loading and also reduces the time and magnitude of consolidation settlement under the weight of the planned embankment.Approximately 74,000 cubic yards of liquefiable alluvial soils were improved by stone columns. Stone column construction occurred in late 2010 and early 2011. This was followed by the embankment and wall construction. Settlement monitoring began with the embankment construction and continued into 2012."

Jan 1, 2017

By Chengcan Wang, Jin-Tae Han, Young-Eun Jang

"The waveform micropile is a newly developed foundation type for increasing the bearing capacity with the created shear keys on the pile’s shaft. Analyzing the increment of resistance at the shear key zone is a crucial factor in the design of the waveform micropile. Hence, centrifuge tests were carried out employing six different models, including a waveform micropile in the axial loading condition. The analysis results of the load-settlement curves showed that the waveform micropile achieved a higher bearing capacity compared to the micropile without shear keys. In addition, the test results revealed that the load-settlement relationship was affected not only by the pile shape but also by the locations of the shear keysINTRODUCTIONA micropile is a small-diameter pile, typically constructed with a less than 300 mm diameter. Generally, the micropile’s construction involves drilling, grouting, and insertion of a reinforcement material, such as a thread bar. The micopile can be utilized in a variety of fields for reinforcing the foundations of existing structures. It also has advantages for accessing challenging areas like limited-access construction sites, including those with a low headroom space and adjacent structures, due to the small size of the construction equipment. Thus, since it was introduced in 1950 in Italy, the micropile has become one of the preferred solutions when other deep-foundation methods are not applicable to the site.Federal Highway Administration (FHWA) gives the micropile design implementation guideline of neglecting the end bearing due to its small diameter but considering the frictional resistance if the bond zone of the pile is in the soil or on a weak rock. The bearing capacity is considered primarily only if the micropile is founded on a high-quality sound rock (FHWA, 2005). Micropile design in South Korea is currently being performed based on the FHWA manual and taking into consideration the frictional resistance for the design as the pile generally sockets into a weak rock or soft rock. Moreover, the frictional resistance within the soil layer has usually been ignored, considering only the shaft resistance of the rocksocketed length in the conservative design. The design concept excluding the frictional resistance in the soil layer, however, may lead to an extension of the pile socket length, which will increase the construction cost. Hence, many researches have attempted to provide better design and construction methods to increase the bearing capacity in a cost-effective way (Juran et al. 2001; Sadek and Isam 2004; Tsukada et al. 2006; Finno 2002; Gomez et al. 2003; Seo et al. 2013)."

Jan 1, 2016

By Abolfazl Eslami, Fatemeh Rostami, Sara Heidarie Golafzani, Mohammad Arabameri

Collapsible loess is classified as problematic soil found in most continents. The loess immediately collapses under stresses induced by axial compressive loading or the soil weight when exposed to moisture. In Iran, vast areas of the Golestan province are covered with aeolian loess deposits. This paper investigates whether the simultaneous effect of inundation and pre-loading in helical pile installation are operative and effective in improvement of Golestan loess. The effect of installation conditions on loess collapsibility is studied via two main approaches, i.e., field investigations and physical modelling. The experimental studies include installation of eight single helix piles in the Amirkabir University of Technology Frustum Confining Vessel, i.e., FCV-AUT. Also, four single helix piles with embedment depth of 3 m and diameter of 250 mm were installed in Golestan province and full-scale pile static loading tests were performed. The results indicated that the simultaneous application of crowd loading and water pressure during installation of helical piles results in better soil shear strength parameters. Moreover, high crowd stresses or low crowd stresses accompanied by water pressure during pile installation brings about similar load-displacement behavior of model piles installed in FCV-AUT and full-scale helical piles.

Oct 1, 2022

"This model specification includes sample text shown in normal font with commentary in italics. The commentary is intended to highlight project-specific items the specification writer should consider during development of the specification. In some sections, typical values are presented to indicate common practice, and these values may be changed to reflect project-specific requirements. The commentary should be removed before using the specification for a project. 1. SCOPE The work consists of designing, furnishing, installing, and testing helical piles used to support foundation loads (compression, tension and lateral), and any ancillary materials (e.g., load transfer devices, etc.) according to the project plans provided and these specifications. Unless otherwise noted, the installing contractor shall provide all labor, tools, equipment and materials necessary to install the required piles. The parties referred to in this specification are as follows: • The Owner is the property owner. • The Owner’s representative is the individual or firm hired by the Owner to design and oversee the overall project. • The pile designer is the individual or firm generally hired by the installing contractor to design the helical piles. • Installing contractor installs and tests (if necessary) the helical piles, and possibly tasks associated with the project. It is important to clearly define the roles and responsibilities of every party on each project to promote good communication and reduce potential for contractual misunderstandings. Different types of contractual vehicles (design-build, value engineering, etc.) require different roles and responsibilities for the various parties, which should be considered in specification development. The Owner will provide suitable access to the construction site for the installing contractor’s personnel and equipment. Unless specifically noted otherwise in the contract documents, the Owner will remove and replace any structures, utilities, pavements, landscaping or other surficial improvements in the work area as necessary to facilitate the work. The Owner will be responsible for overall construction oversight to minimize potential for developing unsafe conditions. The work may include post-construction monitoring of pile performance if required by the Owner or the pile designer to confirm performance of the piles subsequent to their installation. The work may also include installation of additional piles if the initial installation does not meet specified capacity or performance requirements. Responsibility for providing subsurface investigation shall be addressed in the bid documents. The Owner is responsible for providing to the installing contractor all available subsurface soils, rock and groundwater information and geotechnical testing data."

Jan 1, 2015

By Fredrik Sarvell, Harald. Ihler, Veli-Matti Uotinen, Jukka Rantala

"Many of the valid international building codes state that the lateral support provided by the soil is sufficient to prevent buckling of fully embedded piles. However, the development of small diameter micropiles and especially the use of high strength steel have evolved to applications including high capacity elements. The ultimate structural load bearing capacity of a pile in a cohesive soil is decided by examining which gives the lowest value, the peak buckling load and the resisting moment provided by the surrounding soil medium or the structural capacity of the pile cross section. In both cases, the initial deflection of the pile is a significant factor when the axial load bearing capacity of the pile is determined. Steel micropiles are joined commonly with mechanical splices. A less rigid mechanical splice is often a weaker hinge that allows the pile to bend and deflect more during installation increasing the initial deflection of a pile. In addition the less rigid splice element decreases the bending capacity of a jointed pile section and the ultimate axial load capacity of the entire pile. A series of FE analysis performed for various pile sizes suggest that the steel pipe piles including separate pile sections and mechanical splicing elements should have the combined bending stiffness of EIshaft = 0,75 × EIpile. This requirement yields to the buckling resistance of at least 96 % of the solid reference pile with the sameinitial eccentricity in similar soil conditions.IntroductionMany of the valid international building codes state that the lateral support provided by the soil is sufficient to prevent buckling of fully embedded piles. However, the development of small diameter micropiles and especially the use of high strength steel have evolved to applications including high capacity elements. The potential buckling of these very slender high capacity piles in soft soils may in many cases be the controlling design factor of the pile, especially with end bearing micropiles.A typical sequence of soil strata in Nordic countries, such as Norway, Finland and Sweden, constitutes of friction soil or dry crust clay on top of soft clay followed by till. This soil stratum often rests on solid bedrock of granite or gneiss. Conditions like these are suitable for slender end bearing piles subjected to buckling and especially steel pipe piles where most of the material is located at the edge of the cross section. Other reasons for using slender steel pipe piles are for example fast installation with minimal waste, efficient manufacturing and relatively well established design and execution procedures. Minimum quality criteria’s regarding splices for steel pipe piles are recommended to be set as national provisions to ensure quality and comparable procurements in foundation business."

Jan 1, 2014

By Abolfazl Eslami, Sara Heidarie Golafzani

CPT-based methods considered as complementary tools for static analyses outperform other axial pile bearing capacity predictive methods. Considering soil spatial variability and minor errors associated with procedure and operator, CPT-base methods mitigate the effect of latent uncertainties in pile design. These methods were developed based on different databases and purposes. Hence, several statistical and probabilistic attributes were defined and implemented to assess the predictive CPT-based methods’ performance via CPT and pile databases in terms of the model parameter. These features make a comparison among methods in terms of precision, accuracy, and efficiency. Furthermore, CPT-based methods can be subjected to scrutiny over their backgrounds and how they were developed via reliability analysis. In this regard, a database of sixty-two driven piles and their adjacent CPT soundings were gathered, and six commonly applied CPT-based methods were examined according to criteria other than prevailing statistical and probabilistic ones, including; (a) input variables, (b) soil behavior classification (SBC) (c) model assumption (d) Influence zone, and (e) axial loading direction. According to these introduced criteria, CPTbased methods were classified and appraised via efficiency ratio. Eventually, these reliability-based, statistical, and probabilistic criteria evaluate the understudied methods performance for the investigated compiled database and help designers select consciously appropriate predictive methods according to the site conditions.

Sep 8, 2021

By David S. Graham, Benjamin Turner, Paul J. Axtell

Seismic challenges were at the forefront of design for two parallel replacement bridge structures over the Arkansas River as part of the I-30 Crossing Project in Little Rock, Arkansas. Although not an area of the country typically associated with high seismicity, proximity to the New Madrid Fault Zone resulted in design ground motions sufficient to trigger liquefaction in alluvial channel and point bar deposits. A detailed post-award subsurface investigation program utilized CPT with complimentary borings to obtain samples for laboratory testing to assess the continuity of potentially liquefiable layers, from which we concluded that continuous zones of liquefaction across the extent of the north approach could lead to lateral spreading towards the river. An overview of the foundation and superstructure design to resist lateral spreading forces in accordance with the latest published design guidelines and research is presented. Other seismic aspects of the design are covered including timber pile ground improvement to mitigate liquefaction at the north approach embankment and foundation input motions that differ from code-based ground surface motions due to foundation stiffness, strength, and geometry. The project showcases an example of successful collaboration between geotechnical and structural designers with contractor input to address seismic challenges in the South Central US. Furthermore, the importance of considering kinematic demands on columns and other superstructure components – not just foundations – is highlighted.

Sep 8, 2021

By Armin W. Stuedlein, Jim Zammataro, Bernie Hertlein, Daniel Belardo, Qiang Li, Antonio Marinucci

"An experimental program focusing on four drilled shafts was conducted to determine the effect of high strength steel reinforcement bars on lateral resistance, steel casing on axial and lateral resistance, and steel casing without internal reinforcement on lateral resistance. Thermal Integrity Profiling (TIP) Thermal Wires and crosshole sonic logging (CSL) access tubes were installed in each shaft, and thereafter the corresponding non-destructive testing (NDT) was performed on each shaft to assess the integrity of the shafts and to compare the results from the different NDT methods. The results of the CSL tests using scored PVC tubes are compared against those conducted in 73/56 fully-threaded steel hollow bars, whereby the results indicated that the threaded bars served as a good host for performing the CSL tests. The data from the TIP Thermal Wires is compared against the results from the CSL tests for each of the four shafts, and the similarities and discrepancies between the two methods are discussed. This paper will serve as a reference to those interpreting the measurements and data obtained by performing nondestructive integrity tests on drilled foundations.INTRODUCTIONNon-destructive tests (NDTs) embody a set of critical tools for the evaluation of the integrity of constructed deep foundations, particularly for cast-in-place foundation elements. Construction defects may require the rejection of the foundation element by the owner’s representative, resulting in costly repairs or replacements and delays to the project schedule. The use and appropriate interpretation of the results from the NDTs provide the information required when evaluating the integrity of these constructed elements. A cooperative research program was conducted to assess the effects of various construction variables on the axial and lateral performance of drilled shaft foundations, which provided an opportunity to compare the established Crosshole Sonic Logging (CSL) test method to the newer Thermal Integrity Profiling (TIP) Thermal Wire method. This paper presents an overview of the experimental program performed at the geotechnical test site at Oregon State University (OSU), details of the CSL and TIP installation and testing methods, and the results of the NDTs on the constructed drilled shafts. Because one of the shafts was constructed with fully-threaded longitudinal steel hollow bars, this experimental program also allowed the assessment of the use of the hollow bars as access tubes for the CSL tests. Both the CSL and TIP test methods indicated that the shafts were of good quality and free from defects or anomalies; the data obtained using the TIP method also provided an estimate of the as-constructed shaft diameter and the reinforcement cage alignment, which will prove helpful when back-calculating axial and lateral load transfer during future loading tests."

Jan 1, 2016

By Glen Mann, H. G. Vestberg, Robert D. Holtz

"Underpinning of residential and commercial structures is often accomplished using a number of driven-in-place small diameter steel pipe piles. These piles, at least in the Seattle area, are typically described as pin-piles and are driven with an air compressor operated jack hammer to a refusal criterion developed from an empirical basis. Over the past twenty years or so, the materials have improved in quality and strength, and the driving equipment has improved in efficiency and capability. These improvements have resulted in damage to the pin-piles during driving as well as to the driving equipment. The primary objectives of this load testing study were to develop a relationship between the driving penetration resistance of 2-inch diameter pin-piles and the ultimate bearing capacity when piles were driven at different penetration rates and, based on the load test results, to develop an opinion regarding an increase in the allowable axial load capacity [ultimate load capacity divided by a factor of safety] of a 2-inch diameter pin-pile over the currently used permissible load capacity of 4 kips in the Seattle area. Also, if feasible, a reduction in the present driving penetration rate was to be recommended to help reduce the rate and magnitude of pile and equipment damage whilst maintaining the allowable load capacity. The recorded ultimate bearing capacities were also compared with the Tagnent-line and the Davisson analytical methods in an effort to determine if either of these provided a reasonable determination of the pile load capacity.IntroductionThis paper describes the results of a series of load tests performed on small diameter, 2-inch, driven-in-place steel pin (pipe) piles and based on these results, provides the support for a modification to the presently used allowable axial pin-pile capacities.The intent of the load testing program was to determine how much influence the penetration resistance might have on the individual piles' ability to support the allowable axial load without undergoing any significant vertical deformation. For the purposes of this paper the ""allowable load capacity"" is considered to be the ultimate pile load capacity divided by a minimum factor of safety, typically considered to be 2.0 in this area. A pin (pipe) pile comprises an open or closed ended, schedule 80 steel tube which is driven-in-place, usually with an air compressor operated 90 pound pneumatic jack hammer. These jack hammers typically operate at a rate of about 1,200 blows per minute, (Haggard, Holtz and Mann, 2001 )."

Jan 1, 2005

By Brian T. Nereson, Michael C. Penney

"This technical paper was prepared to describe the general process by which the authors designed a column-supported load transfer platform (LTP) for support of asphalt-paved runway and taxiway embankment areas over soft organic soils, the major tasks and observations made during construction of the system, and the outcome of the system design and construction. The LTP system was designed using the method described in the BSI Standards Publication Code of Practice for Strengthened/Reinforced Soils and Other Fills, BS 8006-1:2010 (BS8006), to achieve performance objectives for the project. The design also used other criteria based upon the authors’ engineering experience and understanding of the expected interaction between soils, structures and geotextiles. The design and construction process described herein resulted in a successful project. The authors identified that full-time engineering oversight during construction was of high importance and provided a high degree of value to the project. The authors’ intimate knowledge of the potentially adverse effects of variations in construction practices promoted timely identification of construction deficiencies that could have affected the reliability of the system. This resulted in corrections and modifications being made, while materials were still accessible, to protect the intended performance of the finished system.INTRODUCTIONThe site is located in Marshfield, Massachusetts. The surrounding area is flat and contains significant wetlands with a water table at or near the ground surface. Prior to the improvements described herein, the site was already developed as an existing municipal airport with an approximately 3,000 linear-feet asphalt-paved runway oriented in a northeast/southwest direction (northeast end referred to as Runway 24 and southwest end referred to as Runway 6; Fig. 1). The site is located approximately 0.5 to 1 mile (Runway 24 and Runway 6, respectively) from the Atlantic Ocean.The improvement project included total extension of approximately 550 linear feet of asphalt-paved runways and taxiways over existing wetlands that consisted of soft, organic soils with varying but significant depths (Fig. 2). An initial geotechnical assessment performed for the project identified that the subsurface conditions were not suitable to support the proposed runways and taxiways in their existing state."

Jan 1, 2016

By Abhijit R. Sheth, Craig M. Benedict, John Brun, Ara G. Mouradian

"Amtrak recently replaced the 1907-era bascule two-track bridge over the Niantic River between East Lyme and Waterford, Connecticut. The project included new approach embankments, with approximately 2,500 lineal feet of retaining wall along the west approach and 780 lineal feet of retaining wall along the east approach. The paper focuses on the design and construction of the east approach retaining wall, whose alignment is directly adjacent to an existing wetland area which required protection. An anchored prestressed concrete sheet pile retaining wall was selected for the east approach. A combination of concrete anchor piles and ground anchors were used to support the wall. The design of the wall took into account two simultaneous train live loads, support of electric traction catenary structure foundations, and construction live load, while at the same time preventing permanent impacts to the adjacent wetlands. The design considered challenging subsurface conditions, shallow groundwater, the close proximity of the existing operating tracks, construction staging, and storm surge events in Long Island Sound.INTRODUCTION AND PROJECT HISTORYThe National Railroad Passenger Corporation (Amtrak) recently replaced the 1907-era bascule two-track bridge (No. 116.74) over the Niantic River, between East Lyme and Waterford, Connecticut, along the heavily-traveled Northeast Corridor (NEC). The two NEC tracks, which carry over 50 trains per day, run east-west over a narrow spit of land known as “The Bar”, which separates the Niantic River’s marine estuary to the north from the Niantic Bay to the south, before crossing the river. The bay is an arm of Long Island Sound and is occasionally subject to storm surge from hurricanes.The 1907 bridge was built as a replacement for the previous 1891-era swing-span bridge, and was constructed parallel to, and 49 feet north of, the swing-span structure. The two-track 1907 bridge consisted of a single-leaf bascule span and four approach spans supported on stone masonry piers and abutments. The new bridge increases horizontal navigational clearance for marine traffic in the river from 45 feet to 100 feet, and vertical clearance from 11.5 feet to 16 feet above mean high water with the bridge in closed position. The new bridge, constructed 58 feet south of the 1907 structure, features a single-leaf bascule span of 141.5 feet, with an approach span on either side."

Jan 1, 2017