Search Documents

By John A. Huber

At an underground limestone mine in the Central United States; there were plans for the installation of a limestone processing plant. The special design and layout of the plant called for the installation of a tunnel from the underground mine to the surface above. The dimensions of the tunnel would be 10 feet high, 20 feet wide, and would be 500 feet long on a 17 degree incline. The tunnel would be used for the transportation of raw stone to the surface by a conveyor. A second conveyor would transport processed limestone into the mine for storage, that would be loaded out for shipment later.

Jan 1, 1995

By Shih Wen Wang, Ronald R. Rollins

A blast casting model is proposed to predict the burden velocity in bench blasting. This blast casting model is the first theoretical model that 1) explains the throwing procedures and mechanisms, 2) uses the explosion pressure as the primary source in throwing rock fragments, 3) applies them to field conditions successfully. Also the predicted burden velocities are based on the rock properties, the explosive properties, and the drilling and initiation patterns. This blast casting model is programmed into a computer software "ROCKFRAG". The comparisons between "ROCKFRAG" predicted values and two field test data are in good agreement.

Jan 1, 1992

By Michael J. Sapko, Eric S. Weiss

The U.S. Bureau of Mines has been conducting research on the secondary explosion hazards associated with the mining of oil shale under gassy mine conditions. Explosive incendivity tests have been conducted in a 28 m~3 (1000 ft~3) gallery to evaluate the relative incendivity of experimental emulsion-ANFO blends. The incendivity was measured by determining the minimum inert stemming requirements for preventing the ignition of a methane-air atmosphere by the discharge of hot detonation products from a 5.7 cm (2.25 in) diameter borehole.

Jan 1, 1990

By Qi Jingyue, Wang Zhongquian, Yang Nianhua

Qinling Tunnel is the longest tunnel in China. The rock stratum is very hard rock - intact mixed gneiss. At the beginning of the construction, drift-pilot excavation is very costly due to the use of regular drill and blasting methods. After tests on the acoustic impedance match between rock and explosive, watergel explosive, which has a high velocity of detonation and high brisance, has been used for hard rock blasting. In addition, different cut plans have been compared. It was found that four-large-hole cut is the most effective. And the number of drillholes and specific charge cut down and the average advance reaches more than 94% of the blastholes depth. Thus, the difficult problem of hard rock blasting in drift pilot is successfully solved, while safe and quick construction is guaranteed.

Jan 1, 1998

By R Holmberg, P A. Persson

Recent developments in the methods of measuring rock motion close to the contour at the moment of blasting have given an improved understanding of the extent of rock damage caused by different charge systems. The paper presents the new results and the methods of prediction of damage zones which are used in Sweden for the design of contour blasting rounds. A survey is given of the tools and the techniques for smooth blasting that are now used on a routine basis in Sweden.

Jan 1, 1978

By Michael Wieland

Three laboratory tests were developed for rating the wave-impact ruggedness of cap-sensitive explosives that are used for blasting in underground coal mines. Destructible pipe fixtures, called simulators, reproduce the shock wave or rift compression registered during the cross-hole wave interactions. The rift-compression fixture was modified to render quasi-static desensitization, when utilized with a remote air supply. Waves that were recorded near charge explosions show narrow pulses resembling underwater shock waves, followed by wide, weak humps, called rift compressions.

Jan 1, 1996

By Charles H. Dowding

Public concern over blast-induced CRACKING has led to the search for a radically new approach to vibration control. The present system, while scientifically correct, is cumbersome to explain. Historically the potential for blast-induced cracking has come to be described through velocity time histories, which are correlated with observation of crack extension under controlled experimental conditions. Unfortunately time histories are simply too difficult for jurors and village or county regulatory boards to understand. Furthermore these arbiters must accept on faith that the observers were unbiased. Since these public bodies control the manner in which blasting activity is adjudicated and regulated, information must be presented in a form they can understand and that is not subject to second-guessing.

Jan 1, 1999

By Mark S. Stagg, Rolfe E. Otterness, Stephen Rholl

The Bureau of Mines is engaged in research to develop and test high explosive fracturing and rubblization techniques that will enhance ore body permeability and thus increase recovery during in situ mining. The natural permeability of many ore bodies is too low to allow successful in-place leaching. These deposits could be profitably mined if flow rates of leach solutions could be increased. Blasting represents a potentially low-cost and effective permeability enhancement technique.

Jan 1, 1991

By David Sprott

The effect that underground blasting has on the stability of hangingwalls, pillars and other rock structures is an inherent part of Noranda's geomechanics and mine design program to improve mine safety and stability, increase productivity and reduce ore dilution. The blast monitoring program at Noranda Research aims to provide values of particle velocities and accelerations, delay firing times, and vibration periods to assist with practical blast design and controlled blasting techniques.

Jan 1, 1988

By Tom McDonald, Rodney Burke

As mining progresses in the West, the depth of material has increased, making highwall stability a major factor in safety and production. The Jim Bridger Coal Mine has made highwall stability a priority, concentrating on safety as well as increasing and improving production. Overburden depths are increasing dramatically; the geological environment consists of medium to soft material, faulting, water, and current pit alignment not favorable to joint planes. Angle drilling the presplit at 20 degrees became necessary as vertical presplit drilling produced wall failures.

Jan 1, 1997

By Joseph W. Hejny, Marlyn G. King

Coal mining in the Powder River Basin has changed in recent years to accommodate the large quantity of coal produced. With strip ratios of one to one and up to three to one, extensive amounts of overburden have to be removed to get to the large thick seams of coal. Larger shovels and trucks have been implemented in the removal of this overburden. The addition of draglines and continuous miners have been added to increase the production of coal. Drills used today are capable of drilling up to 13.5 inch blast holes.

Jan 1, 1994

By Vaughn Bowns, Allen Stanley, Brian Redeker

"Running casing in drilling operations is often complicated by boulders or large cobbles.Past practices of dealing with these have included use of drop hammers, attempts to drillthrough or around the boulder, contact explosive charges and even pulling the casing andrepositioning the hole. All these methods are time consuming, expensive and offer noguarantee of success. In this paper a different method of dealing with these boulders ispresented that promises to be faster and less expensive with a much higher success rate.This involves using a light plastic conduit pipe to place a shaped explosive against theboulder. It requires no special tools or techniques not commonly in use in the drilling andblasting industry."

Jan 1, 1993

By J R. "Dick" Daniel

In the fall of 1988, The Cannon mine decided to investigate a central blasting system based on conventional electric blasting detonators being used to initiate rounds primed with Nonel detonators. The advantages of this hybrid detonator system were viewed as being safety and cost effectiveness. A study was done reviewing the safety aspects of utilizing a permanent blasting line installed throughout the main haulage drifts to a central blasting station located at the mine portal. The study addressed the following potential safety hazards: radio frequency induced current, stray current from both electrical utilities and transmission lines, galvanic and electrostatic sources of extraneous current.

Jan 1, 1989

By T I. Jerman

The Du Pont "Detaline" nonelectric initiation system utilizes a low energy detonating cord. It is compatible with conventional detonating cords and shock tube downlines as well as nonelectric in-the-hole delay caps. "Detaline" millisecond surface and in-hole delays offer a great degree of flexibility in developing effective delay patterns for improved fragmentation and reduced vibration. All components are easily assembled in the field.

Jan 1, 1982

By Shulin Nie

The detonability of a chemically gassed emulsion explosive has been studied in recent tests, after the study of three micro-balloon sensitized emulsion explosives. Blasting experiments in steel pipes and computer simulation have been carried out. This study showed that the gassed emulsion explosive and the micro-balloon sensitized emulsion explosives have different desensitization features. Namely, the gassed emulsion explosive can recover its detonability very rapidly after the pressure vanishes, in contrary to the micro-balloon sensitized explosives.

Jan 1, 1997

By Yang Ruilin

Bulk gassing technology is a growing trend in the commercial explosive industry. The gassed bulk products produced differ from microballooned bulk products or cartridged products. It is easy to know the loaded or in-hole density for microballooned bulk products or cartridged products, whereas it is not as straight forward to know the m-hole density for gassed bulk emulsions. The loaded density is one of the key parameters affecting explosive performance and therefore it is important to have a field technique to monitor the in-hole properties of gassed bulk products in order to accurately predict the blast performance and to ensure efficient use of the products.

Jan 1, 1999

By Bill Runner, James T. Ludwiczak

During the last few years, there has been a flood of local, state, and Federal government regulations concerning blasting. Many of the laws and regulations were written by individuals who know little about explosives, the purpose of blasting, or blasting vibration and damage. I feel that the special interest groups responsible for some of these regulations are not trying to regulate blasting, but to stop it completely by unreasonable, non-flexible, regulations. The most recent being the Office of Surface Mining regulations that are already spreading to the quarry industry and will, no doubt, spread to all blasting involving disturbance of the surface.

Jan 1, 1979

By J J. Mullay, G W. Anderson, C J. McFinley, J F. VanNorman, C J. Kefer

Previous work has shown that testing of precompression effects conducted on a small scale under simulated field conditions in actual rock provides a reasonable model for the evaluation of explosives and initiators under the adverse conditions encountered in production blasting. Using this methodology can result in greater understanding of the phenomena as well as the ability to predict performance. This effort has been extended to evaluate various parameters not previously studied in a controlled fashion. The present paper describes the use of this technique to study the effects of delay timing on precompression effects. Intervals from 25 to 150 milliseconds are included in the study. Both VOD measurements and damage estimates are utilized in the evaluation. The results demonstrate that timing delay between holes is quite important in determining the overall effectiveness of a blasting program.

Jan 1, 1994

By Raymond V. Adolphson

Use of explosives effectively and safely has come a long way since its discovery and early stages of development. The need to objectively and functionally train personnel in the safe and effective use of explosives became forcefully apparent in the early 1930's in Forest Service work at the start of the Civilian Conservation corps program.

Jan 1, 1978

By R. K. Wharton

A European Directive requires that an explosive which is sold or transported within Europe must meet certain essential safety requirements from 1 January 2003. The assessment and certification of such an explosive is undertaken by an Explosives Notified Body and if the explosive meets the requirements a certificate is issued that allows the affixation of a CE mark. The presence of a CE mark ensures the product free access to European markets. The paper examines the requirements of the Directive, identifies those explosives that come within its scope, considers the role of an Explosives Notified Body, and explains the process of applying for certification.

Jan 1, 2002