Search Documents

By J. A. Sanchidrián, P. Segarra, S. Gómez

Blasting is a common activity in mining that can cause significant damage in the remaining rock mass. The most commonly used method for predicting vibrations is the Swedish or Holmberg-Persson approach. It is a simple and fast method that uses empirical formulation to estimate the vibration levels based on the explosive charge weight, distance to the source, and other parameters. However, it has limited accuracy and does not consider the effect of free surfaces or other boundary conditions. On the other hand, recently developed methods as the full-field solution (FFS) can provide more accurate predictions of vibrations due to excitations provoked by cylindrical columns of explosive, but the inclusion of free surfaces in analytical methods is a challenging problem. This paper presents a new approach that includes free surfaces in the FFS to predict vibrations analytically in the near-field. The main obstacle to including free surfaces in the FFS was the belief that the solution was non-decoupleable in P- and SV-waves separately. The Heelan's approach was previously used to decouple them, but it only provides valid radiation patterns in the far-field and does not account for intrinsic attenuation. In this paper, we address this problem successfully, allowing for the inclusion of free surfaces in the FFS.

Jan 1, 2024

By Ewan Selers, Gary Cavanough

Drilling automation technology is well advanced and automated drill rigs are in use at a number of operating mines. This is not the case for the other drill and blast processes due to significant technical challenges to overcome. These challenges, with regard to the current “on bench” practices, include placing the initiators, loading the explosive and connecting up the initiation system. Although difficult, these challenges will be solved with engineering advances.

Jan 1, 2016

By Gerard McAlinden, Daniel Frost, Patrick McAlinden, James McAlinden

In an effort to recover Polychlorinated biphenyls (PCB’s) that had leached into bedrock below the Hudson River in Upstate New York, a shaft and tunnel complex was designed that would allow installation of inclined and vertical wells into the zones of contamination to recover PCB’s by gravity. A joint venture of Merco Inc., of Lebanon, NJ, and Obayashi Corporation, of San Francisco, CA, was awarded the contract for constructing the first Tunnel Drain Collection System in the world. Conventional drill and blast techniques were the most economical method to construct the project but due to the presence of PCB’s and community concerns, innovative drill and blast practices were needed.

Jan 1, 2010

By Stephen Mansfield, Saran Sankar

The Sentinel open pit copper mine, operated by First Quantum Minerals Ltd, is located in the North West province of Zambia. The Sentinel orebody is a sediment-hosted, structurally modified deposit in which mineralisation is contained in the phyllite formation, which occurs as a series of layered, continuous sheets having a northerly 20 to 30⁰ dip. The persistent nature of the geological structure can lead to the generation of large slabs when joints are relatively close together or very large blocks when joints are more widely spaced. With standard blasting methodologies, the challenging fragmentation most commonly occurs in the stemming zone and blast interfaces, reducing excavation rates and increasing the risk of crusher bridging events and reduced throughput. A generalised approach to increase powder factor would increase in drill and blast costs and would not be sufficient to target the specific cause of the challenging fragmentation. Implementing differential blast energy based on post blast requirements for different material type, such as ore and waste, and rock mass characteristics is not new in the mining industry. High-energy blasts for ore aim to produce finer materials, enhancing downstream processes such as crushing and grinding, while reducing power consumption and increasing throughput. Conversely, waste rock often requires less energy in order to deliver optimised fragmentation for loading and hauling efficiency. Identifying and applying optimum blast energy to specific material type and geological domains will not only ensure smoother and efficient operations throughout downstream processes, but will have a direct impact on overall profitability of the entire operation. This paper will describe the methods used to model and implement differential blasting across a range of material types in order to deliver the required blast outcomes for ore and waste and the impact on downstream processes and drill and blast unit cost.

Jan 21, 2025

By John Platt, Mark Stephens

"When blasting is required in critical areas and anticipated shot movement and quick cleanup areessential to the success of the project it is extremely important to use the best technology available to achieve the goals expected by the customer. Wampum Hardware was given such a challenge in 2014-2015 when the PA Turnpike and New Enterprise Stone and Lime hired the company to do presplit blasting along the PA Turnpike. The face height averaged 45 feet (13.72m) and the shots had to be controlled to stop within 60-75 feet (18.29-22.86m) of the face or in this situation before they entered the travel lanes on the PA turnpike. In many if not most blasting environments, it is essential in controlling the movement of a blast, to make certain that the face holes are drilled at exactly the right place, with the proper amount and type of burden in front of and to the sides of the borehole. Profiling is an important first step to insure that the holes are drilled at exactly the right place and showing us the correct amount of burden in front of each and every drill hole."

Jan 1, 2016

By Ron Woolf, Corry Goumans

This paper describes rock slope remediation performed along America’s first Superhighway, the Pennsylvania Turnpike and in particular, the specialized drilling equipment designed and built by Pacific Blasting to complete this work. This S-month project was performed on an existing rock cut slope within the Bedford Narrows, a gap formed by the Juniata River through Evitts Mountain. These rocks are in the folded Juniata and Tuscarora Formations within the Valley and Ridge Province and strike northeast with near vertical to slightly overturned bedding.

Jan 1, 2001

By Alexandra Yuyali

The objective of this research work is to increase the drilling ratio represented in tons per drilled meter (ton/m) to reduce mining costs. One of the key characteristics of this research is the use of the ITH (in-the-hole) drilling rig with a water-powered hammer, also known as Wassara™. The patented Wassara™ in-the-hole hammer is powered by high-pressure water instead of air. To reach the objective, a new design of the blast pattern was implemented considering the following: Burden from 1.7 m (5.6 ft) to 2.8 m (9.2 ft) Spacing from 1.7 m (5.6 ft) to 2.7 m (8.9 ft) Drill diameter from 89 mm (3.5”) to 102 mm (4”) Drilling length from 15 m (49 ft) to 30 m (98 ft) Borehole deviation < 2% The result of this new design is the optimization of the drilling ratio (ton/m); having as a baseline 5.2 ton/m with traditional equipment and obtaining 13.7 ton/m with the ITH drilling, which generates annual savings of $2.43M.

Jan 21, 2025

By Alastair Torrance

The performance of commercial explosives is clearly influenced by the conditions under which they are used. Mining companies are supplied with Technical Data Sheets which provide details about explosive properties and its suitable application. These are generally produced using laboratory techniques which may not accurately reflect the quality and performance of the product in the field.

Jan 1, 2013

By Samir Garcia, Alain Mestanza

This technical work was carried out in an open pit copper mining unit, located in central Peru, which has a daily production of 440 thousand tons per day. Currently the pit consists of three mining phases, however, in phase 05 north, there is the construction of a shaft with a height of 375 meters, the function of this structure is to collect and drain the water coming from the pit, there is the importance of preserving its stability and keeping it operational, guaranteeing the sustainability of the operation. For this, a controlled blasting plan was developed that goes from level 4530 to level 4455 to place the central well on a bench, reactivating the pools.

Jan 21, 2025

By Hairong Zeng, Matthew Baumann, Shahram Tafazoli, Edmond Chow

Measurement of rock fragmentation has evolved from a completely subjective and manual process to a statistically objective and semi-automated process. However, ultimately, the vision is to achieve a statistically representative and fully-automated process. From the blast optimization perspective, it is critical to receive reliable rock fragmentation results quickly to incorporate into the planning of subsequent blasts. Since manual rock fragmentation measurement methods tend to be time consuming, a fully-automated method is the practical way to meet these requirements.

Jan 1, 2012

By Felix Degold, Mark Ganster

Achieving a customer optimized fragmentation by using robust data from new technologies e.g. GPS positions of boreholes, fragmentation analysis to calibrate the geology and fragmentation prediction models. The inclusion of the collected data into the blast’s design makes it possible to accomplish a desired particle size distribution.

Feb 1, 2020

By Shazad Hosein, Bill Birch, Catherine Johnson, Toby White, Liam Bermingham

Air overpressure (AOP) from blasting can give rise to a significant number of blasting complaints from residents living adjacent to blasting operations from mines, quarries or civil engineering projects. High amplitudes of AOP are usually associated with the lateral movement of a vertical free face, but it can also be caused by the upward lifting and the venting of gases through the surface of the blast area.

Jan 1, 2018

By Piet Halliday, Ellina Kharatyan

Conventionally, emulsion matrices (unsensitized) need to be sensitized to become detonable explosives. This is done either chemically or mechanically. Both methods have their advantages and disadvantages. Mechanical sensitization involves the addition of microballoons (plastic or glass) to the emulsion matrix, in order to create hot spots during detonation. This is usually done at the manufacturing site and poses a safety risk in terms of the storage, transportation and handling of a 1.1 type explosive. Many countries throughout the world make use of chemical sensitization as opposed to mechanical sensitization as this allows for the storage, handling and transportation of two 5.1 type products rather than the 1.1 type explosive. Chemical sensitization involves the addition of a small amount of a chemical that reacts with a component of the emulsion matrix causing the formation of gas bubbles that act as hot spots during detonation. The disadvantage of this is the lack of accurate density control (due to various factors affecting the reaction) and the lack of comprehensive understanding of the operators of the reaction. This can easily result in poor blast performance. Due to these disadvantages a pumpable, non-detonable (5.1 type) mechanical sensitizer was researched and developed. This product allows for pumping at a 50:50 volume ratio with the emulsion matrix, when loading into blast holes. The significance of this is that a 1.1 type explosive is formed in the blast hole. As such, the security and logistical issues of the transportation and storage of the 1.1 type explosive are eliminated. Another advantage is accurate density control of the final product, specifically in small diameter long hole applications. A cost effective, unique mini pumping system has been developed for the loading of this product. Moreover, this system can easily be used for secondary blasting applications and the on-site packaging of cartridged explosive products.

Jan 1, 2015

By Gordon C. Petersen, Gary A. Almeraris

This paper describes the controlled blasting techniques required to mine a rock tunnel section of a main interceptor located in the Boston Metropolitan area. The 3m (10 ft) x 2.8m (9.25 ft) horseshoe shaped tunnel was driven 490m (1600 ft) by conventional drill and blast methods. The geology varied round by round and consisted of five highly faulted and jointed igneous rock types. The tunnel intersected numerous slickenslides and open mud seams which hampered both drilling and loading operations. Smooth blasting wee critical in order to keep overbreak tc a minimum in this extremely hard but blocky ground.

Jan 1, 1991

By CVB Cunningham

"The Kuz-Ram model as originally proposed included an error in assuming that the mean fragmentsize predicted by Kuznetsov’s equation was actually the 50% passing size. In 2003 Spathis began discussions on this issue and recommended correcting the equation. The correction produced more fines in the predicted fragmentation, which had been a criticism of some users of the original model. Ouchterlony subsequently showed that the error had, if anything been beneficial, and that the Swebrec function adequately covered the fines. This author shows that the Spathis correction does not assist the fines correction in examples examined, but tends to underestimate coarser fractions. An intrinsic problem of communication between academics and engineers is a root of misunderstanding on both sides, and requires patience by both parties to enable value to arise."

Jan 1, 2016

By Jesus Pascual, Benjamin Cebrian

A new Convention Center is going to be built in the millenary city of Toledo, right in the old city limits. The workings will need to excavate some 80.000 cubic meters of granite, which has, a trench-like structure already blasted for the construction (60 years ago) of a parking lot and a shopping area. Surrounding this trench, some few feet away, there are structures and buildings from the 16th century and remainings from previous times that need to be preserved from any damage caused by blasting. Because of this, a vibration analysis was designed according to the special characteristics of this work. Structures to monitor were located at several levels. It considered three different directions of study in order to evaluate the impact of vibrations of the structures located at three different heights of the granite trench. On top, the historical convent of Santa Fe, with some remaining from the 8th century (Muslim domination of the Iberian Peninsula), on the bottom, the Justice Hall of Toledo with 16th century walls, and, in the middle, a wall and a tower from times of the king Phillip II (16th century, the time of the Spanish Empire).

Jan 1, 2004

By Joshua Hoffman, William Chad Wedding, Braden Lusk

The University of Kentucky employs an explosively driven shock tube in the course of experimentation. A good deal of the work completed relates to the verification of blast mitigation products and strategies. The work is dependent upon reliably reproducing specific pressure time histories called out by the test in question. The facilities are located in the workings of an underground limestone quarry in Georgetown Kentucky. As such, the temperature maintains fairly consistent 60°F (15.6°C), making it a comfortable work environment year round. Unfortunately, the relative humidity follows the prevailing weather conditions allowing a wide variation, especially between the winter and summer seasons. A study was undertaken to gauge the influence of relative humidity on shock wave generation, including the positive and negative phases of the wave.

Jan 1, 2011

By Tapan Goswami

The main objective of the blasting phase in a coal mining operation is to maximise the coal recovery. However, coal loss due to blasting is a serious problem. The Australian Coal Association Research Programme (ACARP) reported in 2011 that in Australia one in every ten coal mines is completely wasted due to such losses. Coal is either lost in the spoil, largely due to the blasting operation or becomes diluted and cannot be recovered entirely. The major coal loss mechanisms include losses from the coal seam roof, the floor, the front edge and from dilution. Coal damage and loss mechanisms during cast blasting that have been observed by various authors include: •Excessive cast dragging the coal edge in the cast direction. Movements of this nature are oftenassociated with the formation of trenches. •Spatial movement of overburden where rock shears and moves in a plane above the coal seam,which damages and dilutes the coal. •Rock falling over the coal during the blast often producing indentations in the exposed coal. •The inappropriate use of bulk and initiating explosives that often results in coal damage. •Insufficient stand-off distances from the coal. The Australian coal mining industry has gone a long way towards addressing the coal loss issues since 2011: almost all operations now deploy touch-coal drilling and sporadically use gamma logging for loading overburden. A study was conducted to compare the effectiveness of touch-coal information in which some touch-coal blastholes were drilled on a fixed or random pattern. In another study, some blastholes were drilled to the touch-coal, gamma-logged and mapped to determine stand-off distances. It was found that the coal roof surface created by gamma-logged holes was the most effective option for minimising coal loss. As a result, a variable stand-off distance was found to be the key to minimising losses. This paper discusses the importance of coal mapping, the rock properties of the roof and floor interface of the coal seam, and the significance of loading and initiating designs in minimising coal damage. Furthermore, the importance of using electronic initiators cannot be emphasised enough. This paper also discusses how a cast blast can be initiated from many locations by mitigating geological abnormalities and thereby avoiding spatial movement of rock shearing in a plane above the coal seam.

By Tapan Goswami

This paper discusses the importance of coal mapping, the rock properties of the roof and floor interface of the coal seam, and the significance of loading and initiating designs in minimising coal damage. Furthermore, the importance of using electronic initiators cannot be emphasised enough. This paper also discusses how a cast blast can be initiated from many locations by mitigating geological abnormalities and thereby avoiding spatial movement of rock shearing in a plane above the coal seam.

Feb 1, 2020

By Andreas Bienz

The safety of persons from accidental explosions and fires during manufacture, storage, transport etc. of explosives, pyrotechnics, propellants, firework and ammunition is most commonly assessed according to prescriptive rule-based approach: Safety is given when all requirements which are listed in numerous regulations and directives (such as e.g. safety distances, limited quantities, protective installations etc.) are complied with. Such a deterministic prescriptive rule-based approach is quite easy to apply but has got disadvantages, however: The actual state of safety in a specific case is not explicitly and quantitatively expressed, and it is not distinguished between the endangered individuals and the whole group. As a result, the effects of the safety measures cannot be measured. This is why uneconomical and in the worst case useless safety precautions cannot be avoided. In addition, waivers are difficult to negotiate, meaningful and sound arguments for pro and con being lacking.

Jan 1, 2007