Search Documents

By Lawrence Mirabelli, William Hissem, Gary Veltrop

Capital Quarries Company, Inc., Jefferson City MO produces aggregate products for road base, asphalt, concrete and concrete block. With their production quantities small in comparison to those produced by the goliaths of the aggregate industry, they find it necessary to constantly stay on the leading edge of best practices for cost control, process and production improvement to sustain a successful business. In the words of Eric Strope, President, “The safety of our employees is foremost. They all work hard each day. They are focused on keeping our cost to manufacture down. As I see it, we cannot work any harder so we must work smarter!”

Jan 1, 2009

By Neal Lee, Braden Lusk, John Silva Castro

One of the most common assumptions regarding the use of ANFO versus utilizing 100% sensitized emulsion is that ANFO “turns over” the muck-pile better, due to the “higher gas volume” supposedly inherent in ANFO. This paper examines this assumption and provides quantitative data for analysis. Total gas volume from each product was evaluated using Orica’s I.D.E.X. Code analysis. This analysis was used to determine if gas volume is a significant contributor to differences in fragmentation and movement between blasts utilizing the two different products. A constant drilling and blasting cost per yard for given cut depth, hole diameter, stemming height and rock type was utilized. The cost per yard was held constant by adjusting patterns considering product, accessory, and drilling costs. Photographic fragmentation analysis, dig rates measured quantitatively through production tracking and time studies and qualitative information about the diggability of the blast provided through video recordings were used to evaluate performance. The data collected during the study is presented and recommendations are made regarding the performance of ANFO and Emulsion holding other variables constant for a limited number of blasts.

Jan 1, 2012

By Yves Lizotte, Malcom Scoble, Sanu Hanspal

"This paper reviews the physical, chemical and mechanical components of what is considered to be the anatomy of a blast muckpile. These relate principally to geometry, floor, fragment size and shapedistribution, density, hydrology, weathering, and diggabiity characteristics."

Jan 1, 1995

By Natalie Zeleznik, Brian Hawkins, David Bradley, Rachel Gooding, Patrick Wilson

"An Event Tree Analysis (ETA) is an established approach for logically deconstructing and assessing scenarios for probabilistic risk assessment. This deconstruction into a series of understandable eventsfacilitates probability estimation for explicitly defined explosive terrorism scenarios with consideration of modes of possible failure during execution (a scenario is defined through selection of a target, selection of an explosive material, and interdiction prior to arriving at general target location, etc.). Further, each event is decomposed into a range of possible outcomes. The physical action or reality ofthe outcome is statistically represented by “branches” of the event tree (e.g., the terrorist may choose totarget a stadium, hotel, or subway; terrorists may be successful or unsuccessful in acquiring the material)."

Jan 1, 2017

By Lifeng Li, Jhon Silva-Castro

"Signature Hole Technique is one method to assess the vibration waveform of a production blast.Methematically, it is the convolution between a prior measured waveform of a single blast hole (signature) and a given time delay sequence (comb function). Being an advantage, the inverse operation of convolution, known as deconvolution, can be used to estimate the signature."

Jan 1, 2017

By R. Sibley, K. Perry, E. McCorkle, M. Coy

Black powder has been used in fireworks since the 10 th century in China. To this day, black powder still has a variety of uses, including fireworks, and remains relatively unchanged. Black powder is used in the firework shell to help produce the effect and in the lift charge to propel the shell skyward. The performance of fireworks shells used in displays varies greatly. In fireworks shells, there are two different black powder charges that differ in construction based on the desired performance of the shell. The two charges consist of the lift charge and the break charge. The lift charge is the first to fire and propels the shell out of the mortar. The break charge is the second to fire and is initiated after a delay from the lift charge; its purpose is to burst the shells effect over the desired area of the sky. The lift charge provides the shell with its initial velocity by pressurizing the mortar below the shell body. The pressurization process is violent and occurs in fractions of a second. The purpose of these experiments are to better understand the pressures sustained in fireworks mortars during the firing process. Mortars and shells vary by size and weight. Pressures in each mortar were monitored at various heights along the mortar to provide a pressure profile during shell lift. A high-speed camera was used to measure shell exit velocity near the mortar’s muzzle. This information was correlated with the size and weight of shells and their respective lift charges

Jan 1, 2024

By Dale S. Preece, Lee M. Taylor

Computer simulation of the physics involved in conventional rock blasting can be split into two phases; transient stress wave propagation and rock motion. Because the two phases involve totally different mechanisms and time scales, they must be numerically modeled with two different computer programs. The first phase is usually modeled with a finite element or finite difference code which treats the rock ss a continuum and simulates the transient stress wave and subsequent fragmentation of the rock. The second phase is usually modeled with a distinct element technique where the rock mass after fragmentation is no longer treated as a continuum but as a finite number of distinct particles that interact with each other through collision mechanics.

Jan 1, 1989

By Jennifer Paukula, Steven Lindsay, S. Joon Kim

String loading is the placement of a bead or ‘string’ of emulsion along the lower edge of a development drill hole. The loading hose extraction rate controls the amount of emulsion placed in each drill hole. This allows a controlled distribution of explosive energy throughout the development round. Center holes are loaded using the slowest extraction rate causing the majority of the explosive energy to be placed in the center of the round. The loading hose is extracted successively faster for the buffer and perimeter holes causing less explosive energy to be placed near the edge of the blast. This causes less damage to the rock mass that remains in place after the development blast.

Jan 1, 2012

By Nikolaos Petropoulos, Ulf Nyberg, Ulf Stenman, Daniel Johansson, Håkan Schunnesson

The optimization of the explosive performance is of great importance since blasting is extensively used in civil projects and mining industry. An improved understanding of how the energy from the detonation of an explosive is transmitted to the surrounding rock mass is critical information for the proper selection of an explosive. Therefore, an extensive study was done on the influence of the blasthole diameter on the Velocity of Detonation (VoD) and the detonation front curvature.

Feb 1, 2020

By Dr. Tristan Worsey, Dr. Jhon Silva-Castro

Confinement is an important aspect of blasting. Reducing and increasing confinement can determine whether a blast design performs properly. Over-confined shots usually have poor fragmentation, higher vibrations, and stemming ejection, and unconfined shots usually have a lot of air blast and fly rock. When talking about confinement in blasting, static confinement conditions are typically referenced. Static confinement conditions are ruled by free faces, shot muck, burden, spacing, stemming, hole depth, toe, etc. All these conditions exist in a static state. Static confinement conditions are generally analyzed before the shot takes place, but once the shot starts, the conditions will change according to the sequence and delay of the shot. Once the shot starts, Dynamic confinement takes place. For the authors, Dynamic confinement is the confinement conditions that exist for the charge when it fires and should account not only for the variables included for the static confinement but also for the time and sequence of the shot. The paper explores the theory of dynamic confinement and its role in influencing blast performance. Time and sequence are the main influencers of dynamic confinement and will be the focus of the paper. How to generate the appropriate timing based on blast design, dynamic confinement, static confinement, and geology will also be discussed.

Jan 21, 2025

By Ann Barron, Paul Downing

Those employed in the explosives industry must have a keen familiarity of the explosives products they handle, the safety pro c e d u res they must follow, and the increasing number of laws and regulations governing blasting operations in order to perform their duties satisfactorily. For this reason, companies must make certain that their employees have the necessary knowledge and full understanding of their blasting and non-blasting responsibilities. Consequently, training is one of the most important elements in any company’s safety program.

Jan 1, 2004

By P J. Dailey, S L. Burchell, R F. Chiappetta

High-speed motion picture photography and its application to the mining, quarry, construction, and explosive industries has proven to be a valuable diagnostic tool. The techniques developed allow one to evaluate blasting performance, compare explosive efficiencies in relation to burden velocity, and estimate optimum delay times to provide adequate forward relief.

Jan 1, 1983

By Robert B. Hopler

The history of bulk loaded explosives begins with the loading of black powder and RRP (Railroad Powder) into vertical boreholes. The early air place, net of black powder and nitrostarch dynamites is covered, as are the brands and formulas of the nitroglycerinsensitized "Bagged" powders.

Jan 1, 1993

By Alastair Torrance, Gary Cavanough

Over the past two years a research project has been performed on reactive and hot ground. A key finding is that host materials including carbonates and coal are inhibitors to the reaction of sulphide and nitrates. The mechanism of this inhibition is pH buffering and isolating the surface of sulphide from reactants. It has been identified that acidity is a key driver of the reaction with a pH of 2 required for a reactivity event. A series of decomposition experiments confirmed that reactive and hot ground are essentially the same phenomenon with the heating produced either by the reaction of sulphide with nitrates or an external heat source. The results indicate that the key driver of detonation in reactive ground is energy and heat released from the acid induced reaction of sulphide and nitrate with no indications of sulphide being a catalyst or contributor to detonation apart from being a heat source. There must be sufficient sulphide and thermal insulation to provide and retain enough heat for detonation to occur. A pathway to detonation is postulated whereby the heat travels upwards and results in evaporation of water in the explosive. When the temperature reaches approximately 200°C (400°F) the ammonium nitrate starts to decompose, decreasing the mass of the reacting species. The material in the top layers has reduced density and specific heat hence the temperature of the top region rapidly increases up to >1000°C (1800°F) and may initiate detonation. Field tests on loaded blast holes support this proposed mechanism. Case studies are presented whereby the research findings are used to provide an analysis of historical reactive ground events.

Jan 21, 2025

By Michael Wieland

The thermodynamics work-principle was used to develop the rupture-fracture-throw (RFT) model for ranking the performance of reduced-density explosives when shot in rock or other stratum. The RFT model revises techniques used for the rock-water-jelly (RWJ) model, where the reaction-zone remains trapped within the rock/stratum. Therein, ranking of performance refers to trends for the two resolved components of the total expansion work: the reversible mechanical work taken as the heave and the residual irreversible portion, taken as the undissipated shock. For numeric tractability, the RFT and RWJ thermodynamic efficiency were taken equal, while the RWJ late-stage confinement was replaced with restrained venting through the rock, to render the RFT inefficient heave. The transfer of heat from the reaction-zone was neglected and the root-power formula was used to render the gas-covolume. Ranking trends were found for a generic charge formulation over a wide ranging density, with underwater results noted for comparison. Realistic compositions, some with natural resource materials, were treated for just typical and reduced density. Rock characteristics, ranging from hard rock to weak stratum, were represented by their density and rupture compression strength. Quantitative test results for shock or heave in rock remain difficult, so qualitative guidelines remain helpful when reviewing the graphic trends. Theoretical refinements for rock fragment size-distribution remain under development, though some relationships are touched upon to gain insight.

Jan 1, 2011

By Rafael Tadeu Pinto e Moura, Giorgio De Tomi, Jacopo Seccatore

This paper describes a research and development project in an open-cast mine with the goal to achieve an average P80 of 300 mm (11,8”) in the run-of-mine (ROM) product without altering the existing budget. The project included several variables in the blast design that were not previously taken into account, such as the orientation of natural joint sets in the rock mass, specific energy of the explosive and firing sequence. The new blast design method considered the directions of natural joint sets and determined the drilling pattern and the firing sequence accordingly to favor the movement of the blasted rock along its preferential direction, to reduce its confinement. At the end of the project, it was achieved an average P80 of 304 mm (12”) in the ROM, 50% lower than the one at the beginning of the project. The final blast of the project showed a reduction of 3% of the drill and blast cost, employing the same powder factor and the same drill pattern size used at the beginning of the project. The results achieved show how rock fragmentation is related to variables that are not contemplated in the most common fragmentation models: the firing sequence and the direction of movement in the blast.

Jan 1, 2015

By Donald Jonson

Stockholm’s Northern Link, currently Europe’s largest urban road tunnel project, will be about 5 km long from west to east. Running through two separate, mostly parallel tunnels, each with 2-4 lanes, the complex will include numerous entries and exits, as well as a major branch to the north. The total length of tunnel will be 11 km, of which 9 km will be in rock. Over million m3 of rock will be blasted. The Northern Link will open to traffic in 2015. After a 10-year stop to deal with environmental questions regarding Ekoparken, Stockholm’s unique “national city park”, the Northern Link project in the Swedish capital was restarted in the autumn of 2006, with the construction of five works-access tunnels.

Jan 1, 2009

By Lon Santis, David Buckwalter, Ken Steinmetz

This paper describes a magazine security system using two readily available cellular telephone-based technologies. The system is comprised of vibration sensors and remote cameras. The system is used at a Bureau of Alcohol, Tobacco, Firearms, and Explosives (ATF) licensed explosives storage location in Pennsylvania to comply with PA Department of Environmental Protection (PADEP) regulations. The system provides instant notification to the licensee via cellular modems, text messaging, phone call, and e-mail. Likewise, the licensee can control the system remotely over the internet and using text messaging commands. The vibration sensors attach to the door of the metal type I magazines magnetically and detect any movement or vibration. The cameras trigger on movement and thermal radiation changes and can also be triggered manually to check alarms received from the vibration sensors. The previous system was comprised of a base unit and magnetic strips. The magnetic strips were powered by a hard line from the control unit and mounted on the doors and top of magazine creating a bond, that when broken triggered an alarm. Our main issues with the unit were the delay in alert times and tech support. Because of these issues, we decided an upgrade was necessary. Compared to that previous system used at this site, these new systems are highly affordable, carefree and reliable.

Jan 1, 2014

By R. Ranjan

Stanstead granite has been investigated with respect to its dynamic compressive strength and its strain-rate dependency. A standard Split-Hopkinson Pressure Bar (SHPB) apparatus has been employed to generate strain rates of up to ~500/s through high-velocity impact. The diameters of the test samples were 19 mm, and tested under impact velocities up to ~20m/s. It is found that even within this limited range of strain rates, the dynamic compressive strength for the granite showed nearly a 100% increase in value compared to those obtained under static loading conditions (e.g. compressive strength of 394 MPa at a strain-rate of 600/s, compared to 215 MPa obtained under static loading). The details of the test are described in terms of incident, reflected and transmitted stress pulses, along with means to achieve stress equilibrium in the test samples under dynamic loading conditions. The advantage and drawback of the use of ‘pulse shaping’ techniques to achieve dynamic stress equilibrium are also detailed.

Jan 1, 2010

By Alain Blanchier, Pascal Bernasconi

Blasting operations took place on Channel coast NW of France to extend Flamanville Nuclear Power Plant (EPR new generation). The closest operating reactor building was monitored by a 24 remote vibrations transducers network to fulfil, on one hand, the severe environment constraints and satisfy high degree of productivity required by the project, on the other hand. Although these requirements usually are incompatible, this challenge compelled to introduce a seismic modelling technique to optimize blast designs using electronic initiating system. The “Hybrid Seismic Modelling” (MSH) uses blastholes signatures (seismic vibrations records) which are greatly dependent on geology and alteration of rock mass, explosives, charge geometry, blast configuration, and the final excavation shape. In order to respect severe vibrations limits, excavation layout was divided into areas with specific blasting modules - type and number of charges, single charge, initiating sequence. Thanks to this technique, it has been possible to reach lowest blasts vibrations levels and a better productivity compared to classical blasting operation at the same location in the past. After the modelling method presentation - principle and use precautions, technical improvements are reported.

Jan 1, 2008