Search Documents

By Edward J. Jr Walter, Edward J. Walter

The vibration problem is approximately fifty years old. The original investigation of the U.S. Bureau of Mines was begun in 1930. Significant investigation into the problem was done by Crandell, Langefors, et al, Edwards and Northwood, and again by the Bureau of Mines. This resulted in an effective Safe Limit standard expressed in particle velocity as 2.0 inches per second.

Jan 1, 1979

By Charles Zdazinsky

Back-break induced from blasting is a concern in open pit metal mining because it compromises the conditions of the pit’s final walls. Final walls that have excessive blast induced damage commonly require extra attention and can often lead to increased cycle times. Most importantly however, the safety conditions of a back-broken region can be significantly compromised and it must be addressed to prevent injury and/or damage to equipment. This occasionally results in the necessity to alter mine plans to prevent an incident from occurring in a back-broken region which can be costly to the mine.

Jan 1, 2014

By G E. Frantii

In the exploitation of low grade mineral deposits, blasting engineers are vitally concerned with maximizing the efficiency of explosive fracturing of rock while simultaneously limiting deleterious environmental affects to acceptable levels. Efficiency can be inferred from radiating seismic waves. Likewise, seismic waves carry direct information on damage potential. The usual approach to this problem is to measure the maximum signal level close to a blast, where it is difficult to instrument and where the signal complexity is intensified by mixtures of wave types and by local heterogeneities. Near-field sites are usually more easily monitored and more readily interpreted. Therefore, a study is being conducted to determine if variations in multi-hole, delayed blasts produce measurable changes in the spectra of seismic waves recorded in the near-field and if these spectra can be correlated with close-in strong motions and affects. To date, power spectra for the well-developed phase Lg and its early coda have been computed and are found to vary measurably when nominal changes occur in blast conditions. Up to a distance of about 50 km the spectra of Lg and its coda appear to be dominated by body wave characteristics (thus source-controlled), whereas beyond 50 km path affects seem to dominate. Additional data must be collected to fully explore the consistency of near-field Lg observations and to verify their usefulness as diagnostics of the engineering affects of blasting.

Jan 1, 1977

By M. Khaled, K. Abdel Rahman, M. Khattab

Helwan limestone quarry is located at a distance of 35 km (21.7 miles) to the south of Cairo downtown. Drilling and blasting operations are used to extract the limestone for the Helwan Cement Company (HCC). In 1980’s a new urban community was constructed adjacent to the quarry. This situation led to shifting of the old quarry 5.0 km (3.1 miles) to its current location, to avoid causing blasting problems to the new community. Unfortunately, the new quarry is opened in a highly faulted area, with weak zones of brittle materials. The drilling and blasting crew is facing many difficulties due to the geological complexity along these zones. Moreover, the extension of this community towards the new quarry makes the control of ground vibrations is very important.

Jan 1, 2008

By D Anonby

The Fox Pit at EKATI Diamond Mine is designed with 11 m wide benches excavated using a double benching technique leaving 30 m high faces. Blasting tests were conducted to increase the percentage of benches that meet an 11 m catch width. The subdrill depth for the lower bench trim blasts and the blasthole diameter for the upper bench trim blasts were reduced to maintain the bench crests. Raising the lower trim blastholes by 0.5 m decreases the depth of broken rock below the final bench elevation, and consequently reduces damage to rock that forms the bench crest below. The use of smaller diameter (165 mm vs. 270 mm) blastholes in the A and B rows for the upper trim blast reduces the charge per delay during detonation, reduces the powder factor slightly, and reduces the energy affecting the final pit wall and crest.

Jan 1, 2007

By Catherine Johnson, Kelly Williams

The ability to measure the overpressure of a shock wave is necessary for explosives research such as shockwave focusing and field testing of blast-resistant designs for buildings and vehicles. To record the peak overpressure of the nearly instantaneous pressure rise at the shock front, pressure transducers with a fast response rate and streamline pencil design are needed. Time spent setting up sensors coupled with the expense of high-frequency data acquisition systems, and the inconvenience of low impedance cables can make the process challenging. Additionally, only small inaccuracies in sensor position can drastically change the measurement recorded. Advances in high-speed video imaging make it possible to see the refraction of light due to the high-density gradient at the shock front without the need for parabolic mirrors or additional light sources necessary for Schlieren or shadowgraph imaging. The average shock front velocity between two points can be calculated by dividing the change in position by the elapsed time between the images. Using the Rankine-Hugoniot relationship demonstrated by Swisdak the peak overpressure of the shock wave can be calculated from its velocity eliminating the interference of the gage and mount. This paper investigates the accuracy of this method by setting dual transducer pencil probesat0and180 degrees perpendicular to the central axis of a285-gram(0.63-pound)cylindrical charge to record pressure versus time for comparison to the high-speed video. The axis of the camera lens is aligned with the central axis of the charge with both pencil probes in view. The pencil probes have two pressuretransducersset100millimeters (3.9 inches)apart to measure the time of arrival and are used to validate the velocities calculated from the high-speed images. This method can be used to evaluate the shock wave propagation from more complex prismatic charges with different cross-sectional shapes where precise placement of cumbersome pencil transducers in the near field is almost impossible.

By Mark A. Rugen

It may be difficult to imagine but small engineering companies do exist, even in relatively large cities like San Antonio. Due to the limited capital available for the purchase or use of equipment such as computers, many times the small company must evaluate a blast damage claim by limited means. This paper will discuss how a relatively small company has managed to become the leading blast damage experts in an area without the use of computers or sophisticated equipment. It will be shown that a single individual in a company who is familiar with vibration theory, local soil conditions and who does not mind spending long hours with a calculator and reference books can satisfy both the insuranc e adjuster or attorney, and the homeowner concerning the claim. Several examples will be given which show the typical flow of work and the ultimate outcome. This paper will focus on the special problems encountered by a small firm and how these can be overcome, and the unique interaction of a small engineering firm with both the insurance adjuster/attorney and the homowner that can lead to an equitable settlement of the claim.

Jan 1, 1983

By Italo Onederra, Jason Furtney, Ewan Sellers

The Hybrid Stress Blasting Model (HSBM) is a high level blast modelling research tool which provides results that can still be used implicitly for practical blast design. The code is being developed through an international collaborative research project funded by a consortium of companies which is comprised of explosive, equipment suppliers and major mining houses. A key component of the HSBM is the numerical code and user interface designated as Blo-Up 2.5. To date validation work has focussed on breakage, fragmentation and damage outcomes in controlled laboratory experiments and using large concrete cubes

Jan 1, 2012

By P. E. Hoffman, Joshua Ph. D.

The Institute of Makers of Explosives (IME) led a post-detonation debris collection project in conjunction with a large AN railcar detonation conducted by the Department of Homeland SecurityTransportation Security Administration, Department of Defense-Combating Terrorism Technical Support Office, Sandia National Laboratories, and the U.S. Army Dugway Proving Grounds. This important work will aid in underpinning algorithms used in the IMESAFR (Institute of Makers of Explosives Safety Analysis for Risk) Quantitative Risk Assessment (QRA) tool. The test also provided valuable data about AN detonation characteristics when it is driven to detonation. The test took place at the Utah Dugway Proving Grounds (DPG) on April 27, 2018 and the debris collection was conducted the following two weeks with an average of 20 persons per day and an approximate total of 1,400 manhours. This paper details the collection efforts, challenges, and lessons learned. It also presents some of the initial findings relating to the debris distribution.

Jan 1, 2019

By P D. Katsabanis, S Kim

A number of small scale fragmentation tests have been conducted to analyze the effects of blasting effort on the grindability of granite, granodiorite, limestone and iron ore. Powder factors were modified, post-blast fragments were screened and drop weight tests were conducted on fragments of different sizes to deliver a variety of specific impact energies. The fragmentation from the drop weight tests has been analyzed to examine the effect of impact energy and powder factor on size reduction. A consistent effect of blasting on the various fractions of the fragmentation distribution has been obtained for all rocks used. The effect of powder factor on the impact fracturing of the rocks has been expressed in a convenient relationship between progeny size, impact energy and powder factor used in obtaining the primary fragmentation. It is clear that explosives consumption affects downstream size reduction; depending on the rock, the effect can be substantial at coarser final sizes but very small in the case of grinding to small final sizes. Differences from the expected trend can be attributed to changes in blast design. As an example, the effect of in-hole collision of detonation waves is analyzed.

Jan 1, 2011

By Jhon J. Silva Castro

Blast vibration records used in mining contain unwanted information in the form of noise due to long-period drifts, background noise, and noise due to the conversion of the analogue signal to a digital signal. When recorded signals from blasting are used to find other physical variables, such as going from particle velocity to acceleration or displacement, the additional information in the vibration signal can result in inaccuracies in the estimation of the peak values and more dramatically, the results in displacement or acceleration can be nonzero near the end of the record. There are different proposed methods to clean or filter the unwanted information from the signal. All of the methods are based on finding the best fit of the record average value (baseline) and then subtracting from the record under analysis to produce the desirable adjustment. Different criteria and functions are used to define the best fit. The function to use will depend on the shape of the record average values. The main characteristic of the baseline function is that it represents a low frequency wave. Such a low frequency wave can be a periodic function or a polynomial expression of nth order. According to the order of the polynomial expression, the baseline correction can be linear, parabolic or high order. In this document the detailed procedure and the results for the baseline correction of a blast vibration record using a periodic function and a polynomial expression of different order is presented. The results show that the drift problem when displacement is calculate using velocity records increases with the increase of the distance from the blast.

Jan 1, 2015

By Ian Tolliday

Emulsion Explosives manufacturers are aware of the destabilizing effect that the presence of inorganic impurities such as magnesium and iron and organic impurities such as naphthalene sulfonates and alkyl amines can have on their emulsions. This destabilization often manifests itself as severe crystallization and subsequent product loss. This paper describes the performance testing of specifically developed emulsifiers which give greatly improved emulsion stability in the presence of high levels of impurities. The test work involved a series of stability tests using ammonium nitrate doped with various levels of crystal modifier and anti-caking agent. A further series of tests were done to evaluate the stability using ammonium nitrate doped with various levels of iron and magnesium ions.

Jan 1, 2018

By Bill Paysse, Lyle Ruffle

My intention is to produce a video, pictorial, and oral presentation on utility blasting, primarily power pole holes and ditches. Included will be blasting for a take-off structure inside of Wanapum substation, jointly owned by BPA, PSE, and Seattle City Light, and blasting for 230kV steel tower foundations.

Jan 1, 2007

By Joshua Hoffman, Braden Lusk, David McLane, John Rathbun

The research conducted previously on Shock-Tunnel Waveform Analysis gave a brief insight into the propagation of a shockwave within a shock-tunnel compared to that of an open air arena test. As a refresher, a shock-tunnel is an energy channeling device used to simulate the effects of a large scale detonation with significantly smaller charge weights; having the ability to conduct tests in this fashion can greatly reduce the costs of testing products.

Jan 1, 2012

By Armin Iravani, Changping Yi, Matthias Wimmer, Daniel Johansson, Santiago Gómez, Håkan Schunnesson

Sublevel caving (SLC) is a mass mining method based upon the utilization of gravity flow of blasted ore and caved waste rock. Drilling and blasting are the initial and the major impact on primary fragmentation and later material flow characteristics. The heterogeneity of rock mass has a great impact on materials’ mechanical properties and plays a significant role in rock fragmentation by blasting. In this work, a numerical model for sublevel caving based on 3D Voronoi tessellations was developed to section rock mass into arbitrarily shaped regions for modelling the heterogeneous rock mass. A coupled finite element and discrete element method was employed to investigate both the fragmentation due to blasting and the gravity flow of ore in a heterogeneous orebody. In the coupled model, the caved waste rock was modelled with loose discrete particles while the orebody to be blasted was simulated with bonded particles. The detonation of explosives was described with a particle blast method and a finite element model was used to model the remaining orebody. The results indicated that the fragmentation at the upper part of the ring is coarse while it is fine at the lower part of the ring. The heterogeneity of rock mass induced some boulders after blasting.

Feb 6, 2023

By Anderson da Cunha Meireles, Pedro Garcia, Ernst Young, Leandro Coelho, Carlos Eduardo Soares Feliciano, Key Fonseca de Lima

Rock blasting is a crucial technique employed in mining construction and quarrying industries to fragment large rocks into smaller, more manageable pieces. However, it often generates ground vibrations that can pose significant challenges. This study explores the application of Conformal Prediction (CP) in the context of rock blasting to develop predictive models that estimate blasting-induced vibrations and quantify the associated uncertainties. Various machine learning models were integrated within the CP framework using MAPIE and CREPES libraries. The results demonstrated the effectiveness of CP in providing statistically reliable prediction intervals, making it particularly useful for applications where the stakes of underestimating uncertainty can be high.

Jan 21, 2025

By Roger L. Keller

This paper covers the design and test blast procedures for several drop shafts and edits leading to the completion of a recent Rochester Pure Waters Expansion Project . Due to the projects "in-town" presence, and its close proximity to many sensitive vibration sites, very stringent ground vibration limitations and guidelines for blasting were places on each site.

Jan 1, 1991

By Wang Zhong Qian, Liu Hui

The paper proposed a fractal and damage model for rock-breaking by blasting, which assumed that the process of rock-breaking results from intrincent fractal development and the accumulation of damage. Remarkably, the process is of fracture character. Based on the model, a computer program is compiled to calculate the 3-dimension damage distribution in blasting crater. Trial results agree well with the predicted results, showing the model set up in the paper is sound.

Jan 1, 1997

By AK Chakraborty, AK Raina

Burden of drill hole is third most sensitive parameter effecting the ground vibration in blasting apart from maximum charge per delay and distance. Various types of burdens can be seen in practical bench blasting situations. Burden can be expressed as drilled burden and initiation burden. Drill holes may have various front row burdens (toe burden), which may be different from the designed burden. In order to ascertain the impact of front row burden as well as the initiation burden on intensity of ground vibration and air overpressure experiments were conducted in sandstone overburden benches of an opencast coal mine and limestone quarry. Blast trials were carried out in cognisance of both drill and initiation burden while keeping all other parameters constant. Effect of front row burden was also extensively studied by keeping almost all other parameters constant. The results of the study reveal that there is substantial influence of front row burden on the vibration and air overpressure. The statistical analysis of vibration and air overpressure data with drilled burden and initiation burden gives significant evidence that the level of peak particle velocity of vibration (Vmax)) is reduced by reducing effective burden with modification of initiation. Data analysis carried out for air overpressure versus initiation burden shows that reducing effective burden with modification of initiation results in increasing the level of P. The study reveals a qualitative assessment of the influence of burden on the blast induced vibration and air overpressure. The study also recommends to modify the initiation pattern to reduce the effective burden in order to reduce the vibration, without disturbing the fragmentation.

Jan 1, 2004

By Richard Givens, Thomas Baginski

Technological advancements in warhead designs and implementations have driven the development of arrayed initiation networks of highly accurate, highly reliable, and extremely safe detonators. Recent development efforts have produced advanced Exploding Foil Initiator (EFI) based systems that have been adapted for civilian use in commercial blasting applications.1,2,3,4,5 This novel, high technology system promises multiple improvements and advantages over the manufacturing, transportation, tracking, storage, inventory and field operation of current detonator systems. Ultimately the insertion of this technology would result in fielding a Non-Energetics Based Detonator (NEBD). Insertion of complementary technologies into the detonator’s supporting systems would greatly advance current detonator hardware/software.

Jan 1, 2011