Search Documents

By Robert Stefanko

The following tables contain the average, maximum and minimum power parameter levels for several mining machines. Power factor is listed only for defined transducer output regions. The reasons for the undefined areas are provided in the Instrumentation Chapter. Several maximum voltage drops are included, and are computed from the no load line-to-line voltage: Again, the drops are from measurements at the low side of the load center. The machines are: Continuous Miners; F6A Alpine 76AM Jeffrey (d-c) 8CM Joy 8CM (10CM) Joy 9CM-2AH Joy loam Joy CU-43-2H Joy 2 each CM26H Lee-Norse CM28E Lee-Norse Shuttle Cars; 18SC Joy 48S Torkar (a-c) 2 - 10SC Joys input to rectifier 2 - 16SC Joys input to rectifier

Jan 1, 1973

"These tentative coal mine inspection standards have been prepared as a guide for the Federal inspection of coal mines of the United States. Much time and thought have been spent by various members of the Safety Division in the preparation of thses standards, and it is believed that compliance with them eventually will be possible in most mines. In many instances objections will be raised to them owing to long-established mining customs and practices that are inherently of dubious safety and to a natural inclination to oppose change. In other instances there will be valid objections due to conditions not foreseen at the time these standards were prepared. Or there may be substandard conditions and practices due to original mine layouts that it is not practicable to change during the lifetime of the mine; in such instances it is likely that some effective measures are or can be taken toward lessening hazards.With the rapid change in mining methods some of the standards may become inapplicable and it may be advisable to revise them to meet the new conditions. Therefore, questions regarding these standards and suggestions regarding new standards should be brought to the attention of the supervising engineer of the Coal Mine Inspection Division so that modifications of and additions to these standards may be made from time to time.In many respects these standards exceed the provisions of the various State mining laws, and some may conflict with the laws of some States. In cases of conflict, the intent is not to advocate noncompliance with State laws but to suggest that it may be desirable for the State to reconsider such laws or safety orders.Although an effort has been made to word these standards so that they may be readily understood, nevertheless, a reasonable interpretation should be placed upon them. In fact, in numerous instances the words reasonable"", ""suitable"", and ""properly"" are used in recognition of the fact that reason- and sound judgment enter into the carrying out of the safety endeavor.The policy of the Bureau on some vitally important safety matters in mines is set forth in its published Safety Decisions. These decisions have been consulted and used in the preparation of these standards. These decisions also are now being reexamined by its Mine Safety Board."

Feb 1, 1942

By Edward A. McClatchie

A methane monitor that complies with 30CFR75.313 has been designed and fabricated using a novel pressure modulated infrared absorption technique. The methane monitor met or exceeded in performance all of its target specifications. The monitor was operated continuously during production mining for the entire duration (45 days) of the in-mine test; no failures occurred during the test. The monitor was regularly checked with calibration gas and no shifts in calibration were found during the in-mine test. Operating principles, performance data and electrical schematics are included in the report.

Jan 1, 1976

By N. Seidle

Numerous studies conducted in the 1960's and 1970's concluded or implied (1) that a high accident rate in terms of severity and frequency exists among new (first year) operators of mine machinery equipment, and (2) that lack of experience and training is a major cause of this high accident rate. Further studies refined this premise to show that the major causes of accidents among first year operators are: (1) lack of manipulative skills; (2) failure to follow/adhere to routine procedures; and (3) failure to recognize and respond properly to hazards. This report describes the design, development, and manufacture of a shuttle car operator training system, including a program of instruction which: ? Is economically feasible. ? Addresses accident data and specific causes of accidents. ? Includes an aerospace quality simulator of sufficient fidelity to teach and develop manipulative skills, recognition of and response to hazards, and routine and emergency procedures. ? Is designed to significantly reduce the severity and frequency of accidents especially during the operator's first year. ? Is designed to significantly improve the performance of the trainee as compared to the standard learning curve. Development of the simulator produced several valuable by-products including a major state-of-the-art technological advance in visual systems for simulators, and a first-time application of (certain) advanced filming techniques to underground filming.

Jan 1, 1984

By C. H. Titus

This study consists of four descriptive Sections covering respectively: a state-of-the-art literature survey on ungrounded and grounded power systems, a report on literature pertaining to human threshold limits of electric shock, an analysis of the performance requirements of isolated systems and a section on design and performance specifications for an isolated system the final section includes copies, and translations where applicable, of the most important articles on foreign mining practice as well as some technical publications which could be difficult to obtain elsewhere. Section 2 - Literature Survey In analyzing the available literature on ungrounded systems it became apparent that too strict an interpretation of Section 1.1 of the Contract would limit the survey in both period of time analyzed and in available literature which discussed several types of power systems. Therefore, the survey was expanded to cover approximately the past twenty-year period and to cover literature which addressed itself to both ungrounded and grounded power system operation. Section 2 gives a brief summary of this literature survey and lists the important papers and books which were examined.

Jan 1, 1972

By J. L. Holman

The Bureau of Mines, at its Rolla Metallurgy Research Center, has devised methods for separating and reusing the major portion of waste plastics discarded in urban and industrial refuse. Waste plastic concentrates from a local collection drive, recycling center collections, urban refuse pilot plants, and the secondary metals industry were separated into three major thermoplastic families--polyolefins, styrenes, and vinyls--based on differences in density using a Bureau-designed sink-float-elutriation hydraulic separator. Other separation methods and systems such as air classification, jigging, liquid media, screening, and electrostatics were studied. Vinyl plastics contain up to 50 percent HC1. It was found that over 90 percent of the HC1 in vinyls can be recovered as usable hydrochloric acid by pyrolysis at 350° C. The remaining pyrolysis products which had heats of combustion in excess of 12,000 Btu/lb, could become valuable as a future source of energy. A characterization study conducted on eight chopped wire insulation wastes from secondary copper and aluminum processors showed that most wastes contained 2 to 7 percent residual metal and large percentages of vinyl. The residual metal content of some of these wastes was lowered to 0.1 percent and the vinyl portion segregated using various separation techniques. The research also suggests ways in which reclaimed thermoplastics may be fabricated into useful products.

Jan 1, 1974

By H. C. Carpenter

This literature study of methods for desulfurizing residual fuel oil was conducted by the Bureau of Mines at the request of the Department of Health, Education, and Welfare. The sulfur compounds in residual fuels are believed to consist chiefly of condensed thiophenes and other polycyclic sulfur compounds. Hydrodesulfurization appears to be the most promising method for desulfurizing these oils and is the only method applicable to all types of sulfur compounds. There are indications in the literature that hydrodesulfurization without hydrocracking of residual oils may require higher pressures than used in present desulfurization processes, but no cost data and little experimental data are available on the higher pressure operation. Literature proposals for hydrogenating residual oils and heavy crude oils are exclusively for hydrocracking the oils to lower boiling products with accompanying partial desulfurization of the residual fuel fraction. Costs of the hydrocracking operations appear the closest available to probable costs of hydrodesulfurizing the oils, and have been reported (in 1955 to 1957) as $500 to $840 investment cost per daily barrel of capacity, with total operating costs of 70 cents to $1.10 per barrel.

Jan 1, 1963

By H. C. Carpenter

This literature study of methods for desulfurizing residual fuel oil was conducted by the Bureau of Mines at the request of the Department of Health, Education, and Welfare. The sulfur compounds in residual fuels are believed to consist chiefly of condensed thiophenes and other polycyclic sulfur compounds. Hydrodesulfurization appears to be the most promising method for desulfurizing these oils and is the only method applicable to all types of sulfur compounds. There are indications in the literature that hydrodesulfurization without hydrocracking of residual oils may require higher pressures than used in present desulfurization processes, but no cost data and little experimental data are available on the higher pressure operation. Literature proposals for hydrogenating residual oils and heavy crude oils are exclusively for hydrocracking the oils to lower boiling products with accompanying partial desulfurization of the residual fuel fraction. Costs of the hydrocracking operations appear the closest available to probable costs of hydrodesulfurizing the oils, and have been reported (in 1955 to 1957) as $500 to $840 investment cost per daily barrel of capacity, with total operating costs of 70 cents to $1.10 per barrel.

Jan 1, 1963

By George H. Holmes

This paper is one of a series on mining methods and practices being prepared by the Mining Division of the Bureau of Mines . It describes briefly operations and mining methods at the Basic Refractories , Inc. , brucite deposit , the only commercial deposit of brucite in production in the United States . The mine and crushing plant are in secs . 26 and 35 , T. 12 N. , R. 36 E. , M. D. B. & M. , northwestern Nye County , Nev . , 1 mile east of Gabbs and about 33 miles northeast of Luning , a town on the Mina branch of the Southern Pacific Railroad and U. S. Highway 95. ( Figs . 1 and 2 ) .

Dec 1, 1949

By John L. Schaller

The Bureau of Mines, U.S. Department of the Interior, has investigated the extraction of alumina from domestic kaolin clay by leaching with boiling 26 wt-pct hydrochloric acid. Acid leaching of crushed calcined kaolin feed yields slurries that are slow settling and difficult to filter because of the presence of fine particles generated in crushing, calcining, and leaching. Laboratory research showed that tumbling and moistening crushed raw kaolin on a pelletizing disk caused the fines to agglomerate on the surfaces of the larger particles, while the sharp edges and corners of the larger particles were rounded off. Minus 16-mesh crushed raw kaolin was misted on a 36-in-diam, 8-in-deep pelletizing disk at rates of 175 to 250 lb/hr, and was calcined in either a rotary or a fluidized-bed calciner; negligible degradation occurred. The physical properties of the misted calcined kaolin were evaluated in the leaching system of the clay-hydrochloric acid miniplant. Only minor attrition occurred during leaching, and the slurry was readily filtered on a continuous belt filter.

Jan 1, 1982

By W. H. Somerton

Many oil-producing formations contain significant amounts of clay. Because of the large surface area and reactivity of such surfaces, the response of the formations to various recovery processes may be dominated by the reactions of fine-grained minerals, including clay minerals, in the formations. Thus, the success or failure of enhanced oil recovery (EOR) methods may be controlled to a large extent by the amount and nature of these minerals in the formations to which the methods are being applied. One of the deterrents to the successful application of chemical EOR methods is the loss of chemicals injected into the formation, to non-oil recovery processes. These chemical loss processes include adsorption onto mineral surfaces, chemical reactions with rock and fluids in the formations, possibly leading to precipitation and plugging of the formation, and trapping of chemicals in parts of the rock structure so that they become unavailable for displacing oil. Chemicals that may be injected include surfactants, polymers and caustic solutions which react with organic acids in the crude oil to produce surfactants in-situ. These losses are most pronounced in fine-grained reservoir rocks containing substantial amounts of clays.

Jan 1, 1984

By Kenneth L. Cashdollar

The Mine Safety and Health Administration (MSHA) and the West Virginia Office of Miners? Health, Safety, and Training (WVOMHS&T) investigated the explosion at the Sago Mine in West Virginia, which occurred on January 2, 2006, and resulted in 12 fatalities. As part of the investigation, the agencies requested that the National Institute for Occupational Safety and Health?s (NIOSH) Pittsburgh Research Laboratory evaluate the effects of explosions on specific mine ventilation seals and other structures and objects at its Lake Lynn Experimental Mine (LLEM). The results of the LLEM study would assist MSHA and WVOMHS&T in a more thorough understanding of the various questions that arose during their investigations of the explosion. Six large-scale explosion tests were conducted in the LLEM from April to October 2006. The protocols for these tests, and in particular the procedures for constructing various Omega block seals, were developed mainly by MSHA and WVOMHS&T. NIOSH developed the experimental procedures at the LLEM that would provide the required range of explosion pressures against the seals. Three 40-in-thick seal designs using Omega 384 low-density block were constructed in the LLEM and exposed to various explosion pressures. These seal designs are referred to in this report as the ?2001 design,? the ?hybrid design,? and the ?Sago design.? The 2001-design Omega block seal (80 in high) located in crosscut 2 of the LLEM survived all six explosions, with pressure loadings up to 51 psi. The 2001-design Omega block seal (88 in high) in C-drift was destroyed during Test 2, which subjected the seal to a head-on explosion that resulted in a pressure loading of 51 psi. The height difference between the two seals and the orientation of each seal to the explosion were contributing factors. The higher seal would be weaker for the same seal thickness. The hybrid Omega block seal in crosscut 3 survived an explosion at a pressure loading of 25 psi and failed during another explosion at a pressure loading of 39 psi at the seal. Based on these tests, it seems that the hybrid seal design is weaker than the 2001 seal design. The Sago Omega block seals were constructed in crosscut 3 and C-drift before Test 3. The crosscut 3 seal survived a pressure loading of 18 psi and was destroyed during an explosion at a pressure loading of 35 psi at the seal. The C-drift seal survived a head-on explosion that resulted in a pressure loading of 21 psi and was destroyed during an explosion with a pressure loading of 57 psi at the seal. Based on these LLEM tests, it seems that the Sago seal design is weaker than the 2001 seal design, yet it still complied with the requirements of 30 CFR 75.335(a)(2) that were in effect at the time of the mine disaster. During these LLEM explosion tests, the distance of seal debris travel was also measured. In Test 5, the C-drift seal was destroyed during a head-on explosion that resulted in a pressure loading of 57 psi, and the seal debris was thrown over 500 ft. In Test 6, the C-drift seal was destroyed during a head-on explosion that resulted in a pressure loading of 93 psi, and the Omega block debris was thrown over 900 ft. During these tests, the explosion pressure effects on other structures and objects were also documented. Unless otherwise specified, all of the pressure data listed in this report represent the highest recorded smoothed (averaged over 10 ms) explosion pressure loadings. The information in this report was used by MSHA and WVOMHS&T as supporting data in their analyses and investigative reports of the Sago Mine explosion.

Sep 1, 2009

By Olman Hee

This study investigates the identity and relative importance of factors affecting the future demand for phosphate rock, potash, and nitrogen. The main objective is to analyze demand relationships for these chemical raw materials for some specified past period, and to utilize this information to make projections of consumption into some designated future period. The end-use approach is used, which divides total consumption of each chemical raw material into agricultural, industrial, and export use. Multiple regression analysis is employed to statistically measure the relative effects of the different factors on consumption in each end use. The general method centers on the construction of a consumer demand model, the fitting of the respective equations in the model, and the interpretation of the statistical results. Direct and cross price elasticities of demand are computed for each end use of the chemical raw materials. These give an insight into expected changes in consumption with respect to given changes in price. The results of this study indicate that price, consumer income, and level of technology are factors which measurably affect consumption of chemical raw materials. For phosphate rock and potash, the agricultural and industrial end uses showed an inelastic demand, whereas for nitrogen, all end uses (including export use) exhibited an elastic demand. Among the chemical raw materials, average annual growth of consumption of nitrogen for agricultural and export uses to 1980 is expected to be notably higher than that for phosphate rock and potash.

Jan 1, 1969

By John H. Johnson

Diesel tailpipe CO, C02, NO, and N02 concentrations by the Emissions Measurement Apparatus (EMA) were found to compare satisfactorily with simultaneous concentrations by instruments in the MSHA engine certification laboratory in Bruceton, Pa. The EMA was then applied to the measurement of LHD vehicle diesel tailpipe gases and smoke opacity in the White Pine and Brushy Creek Mines. A general experimental approach was developed by which instruments could be compared for the measurement of diesel exhaust pollutant concentrations in the 1/2 to 5TLV range. The concentrations are changed by varying engine speed, dynamometer load, and the portion of the exhaust which enters the dilution tunnel. Dräger detector tube diluted exhaust CO, CO2, NO, and NO2 measurements were compared with simultaneously taken portable instrument measurements. Diesel exhaust interference inaccuracies were separated from inaccuracies due to detector tube calibration by comparing the instrument readings with both actual detector tube readings and detector tube readings corrected by recalibration of the detector tubes alongside NBS traceable calibration gases. The detector tubes' accuracy was found to be only slightly affected by diesel exhaust interferences and it was concluded that most measure within certification limits established by the National Institute for Occupational Safety and Health. The effects of 2 exhaust system configurations on the pollutant concentrations in a dead-end heading were studied. Both of the configurations exhausted the gases near the roof, directing them toward the crosscut, and both improved the stratification of the air in the heading, due to the bouyancy of the hot exhaust gases. One of the configurations was a pair of Fume Diluters which diluted the exhaust with air by a 10:1 ratio, and the second system was simply a pair of exhaust pipes, bent to direct the exhaust similarly to the fume dilutors. By redirecting the exhaust, the concentration of C02 measured on the LHD vehicle was reduced by as much as 507, in dead-end headings up to 200 ft long. The Fume Diluters showed no improvement over the simple redesign of the exhaust system.

Jan 1, 1980

The general nature of the special constructional features that are required to provide safety from explosion hazards on machines approved as permissible by the Bureau of Mines is fairly well known to mining men who are at all interested in safety. These requirements are outlined in the schedules under the provisions of which the investigations of such machines are conducted. Also, the method of conducting inspections and tests of such machines has been described in Bureau of Mines Bulletin 305, Inspection and Testing of Mine Type Electrical Equipment for Permissibility, published in 1929. A more detailed knowledge of the special safety features of a particular machine is often useful and sometimes essential for inspectors, safety engineers, maintenance men, and engineers in selecting machines for a particular application. Three bulletins that give information of this nature have been-published by the bureau, viz., Bulletin 313, Permissible Storage-Battery Locomotives and Power Trucks. Bulletin 343, Permissible Coal-Handling Equipment. Bulletin 382, Permissible Coal-Cutting Equipment. Report of Investigations 3309, Permissible Electrically Operated Air Compressors, which contains similar information, was issued in August 1936, and a Report of Investigations 3326, Permissible Electrically Operated Room Hoists, was issued in January 1937. Thus, the present paper is the third to give detailed information concerning permissible machines of types not included in bulletins, and covers all the rock-dust distributors approved prior to October 1, 1936.

Jan 1, 1937

By Harry W. Campbell

A mineral survey conducted by the U.S. Bureau of Mines in 1983 identified no mineral resources in the Beaver Meadows, Blind Horse Creek, Chute Mountain, Deep Creek/Battle Creek, and North Fork of Sun River Wilderness Study Areas (WSA's). A prospect east of the Beaver Meadows WSA has low potential for lead resources. Sand, gravel, and limestone occurrences are numerous in the WSA's; however, similar or better quality materials outside the areas are abundant and more accessible to potential markets. Impure coal and titaniferous-magnetite occurrences are near the WSA's, but are not known to occur within these areas. In 1983, there were 7,025 acres leased for oil and gas within the five WSA's; no current mining claims were in or near any of the WSA's. Evidence of mining activity was found at only one prospect in the WSA's. It is inside the Deep Creek/Battle Creek WSA; no resources or resource potential were identified at this prospect.

Jan 1, 1984

By E. C. Tarpley

An acid-extraction procedure developed in Germany for determining mineral matter in coal was investigated by the Bureau of Mines to determine its application to American coals. It was found to be suitable for all ranks of coal from anthracite to lignite if modified slightly for coals containing considerable quantities of calcium compounds, such as calcite or calcium humate. The precision of the method is satisfactory, and the results are probably closer to the true content of mineral matter than those obtained by empirical formulas. The method requires considerably more analytical data than the Parr or approximation formulas but is no more time consuming than obtaining the necessary data for the King, Maries, and Crossley formula (theoretically the most comprehensive empirical formula used). An appendix to this report includes a detailed description of a recommended procedure.

Jan 1, 1959

By Stephen H. E. Phillips

This report outlines the modifications that have been carried out to the original prototype rectangular shaft sinking equipment for its use in a circular shaft. The surface testing of the machine is described where seven, 24 ft. diameter shafts were excavated to an average depth of 21 ft. at rates ranging between 1 ft/hr and 1.9 ft/hr depending upon the prevailing conditions. The durability and productivity standards for the equipment were established indicating that the objectives of the project had been realized. That is, when using the machine the sinking rates could be increased by 25% and costs reduced by a corresponding amount compared with conventional drill and blast methods. In addition it was shown that the machine had been developed to a state of fitness for sustained underground use.

Jan 1, 1981

By Anthony D. Szpak

The purpose of this program was to demonstrate the feasibility of Illuminating various types of underground coal mining machinery as required by the Federal Coal Mine Illumination Standards Part 75.1719 to 75.1719-4 Code of Federal Regulations Title 30. Nine various machines were illuminated and the illumination systems were evaluated for a 3 month period of operation. Factors evaluated were ease of implementation, reliability, ease of maintenance, acceptance by mine workers and operators, Illumination degradation and durability.

Jan 1, 1981

By Edwin S. Secor

The Federal Bureau of Mines conducted a field survey of 153 bituminous coal strip and auger mines to estimate coal recovery from surface mines in the Eastern United States. Recovery was calculated from field data by measuring coal losses resulting from mining coal and leaving barriers. Mean total recovery for strip mining in States east of the Mississippi River was 83.0 percent and ranged from 72.3 percent for Tennessee to 91.3 percent for Maryland. Mining losses and barrier losses were 10.1 and 7.7 percent, with standard deviations of 4.8 and 10.4 percent, respectively, indicating that barrier losses, although less than mining losses, were more variable. Mean total coal recovery varied only slightly for the two regions studied; 82.7 percent for Appalachia and 84.3 for the Midwest. Total recovery grouped by mining method--contour, area, and mountaintop removal--was 79.8,84.7, and 85.3 percent, respectively. Mean auger recovery was 35.9 percent; of the total average loss of 64.1 percent, over one-half resulted from design limitations while the remainder was attributed to operating losses. The wide recovery range at individual mines indicates the variability of the eastern surface coal mining industry. Because of this, care should be exercised in applying the results of this report to reserve estimates other than those of a general nature.

Jan 1, 1977