Search Documents

By Roy F. Abernethy

All samples tested showed some loss of heating value for the 5-month period under all 4 storage conditions. The losses increased as the time of storage increased, with the pan-storage samples showing somewhat greater losses than those in cans. The individual daily analyses for the first 2 weeks and the analyses every other day for the third and fourth weeks of storage vary within the approximate tolerance of the test for heating value. During the first 2 months of storage the changes in heating values were not Significant for the samples from Pennsylvania, Indiana, and Colorado. The Ohio coal indicated some loss by the end of I month, which increased to a value measurable with certainty by the end of 2 months. These data show that (1) small changes may occur even to samples in closed cans and (2) the laboratory sample should be handled as expeditiously as is practical until the analysis is completed. The statement by the ASTM that "If the B.t.u. determination is an important consideration in the sale of coal, the time elapsed between sampling and analysis shall not exceed 30 days,"3/ is quite adequate for 3 of the 4 coals tested. The change in the Ohio coal stored for 30 days is merely indicated and could not be determined with certainty by the techniques normally employed. The data on free-swelling indexes determined on can samples, after 30° C. air drying, show that only the Indiana coal lost more than one unit in free-swelling index number in 120 days. No significant changes were observed with the samples from Pennsylvania, Ohio, and Colorado in the 5-month period.

Jan 1, 1958

By B. Gillenwater

This report describes the results of investigations into four specific areas related to trolley wire power distribution systems in coal mines. These are: 1. Partially insulated (shielded) trolley wire 2. High-speed insulator fault detectors 3. Dual-wire trolley systems 4. Insulator failure indicators. Prototype devices or designs were developed in each area. In addition, a brief survey was made in an attempt to assess the Future of mine trolley systems, and data was collected and reviewed in an attempt to analyze the nature of trolley wire related accidents. Other options for decreasing the risks associated with trolley systems that arose .during the study are briefly described in appendices. These include insulating equipment and miners from return and/or energized conductors and use of a segmented trolley wire with local control of current delivering capability.

Jan 1, 1981

By W. H. Forbes

The prevention of accidents from falls of roof and coal requires a considerable amount of personal judgment , for conditions are different even in adjoining working places in the same mine , and conditions may change from hour to hour even in the same working place as the coal is shot down and loaded . Experience has shown that many men can not or do not exercise enough care to protect themselves from injuries ; moreover , where the foremen have been made directly responsible for the safety of the men under them , accidents from falls of roof and coal have , in many instances , been reduced as much as 50 per cent . There is now no question that careful , constant , and intensive supervision is essential in preventing acci- { dents and more especially accidents of this class . Falls of roof and of coal account for approximately 50 per cent of all coal mine accidents and annually result in the death of approximately 1,000 men and cause lost - time injury to approximately 50,000 men . These and other accidents are recurring with little or no diminution , usually not because of the lack of knowledge of safe and dangerous practices , or of the technique of safety , but largely because of the lukewarm interest of major executives in safety or the failure of mine officials to formulate and to enforce common - sense rules and regulations . When failure is the outcome of a sincere attempt of the managing officials to teach safety to the miner , the fault may usually be attributed to misguided effort . Various solutions for the problem of eliminating accidents from falls of roof or coal have been suggested , some of which are : Standard system of timbering for the specified mining districts ; departure from the room-and - pillar system to a more concentrated system of mining ; more intensive supervision - that is , 1 section foreman for every 25 loaders instead of 1 section foreman for 75 , 80 , or even more loaders the practice in most mining districts . - However , investigations conducted by the writer at numerous mines operated by a number of mining companies in several districts show that employees and officials alike are inclined to work under loose and unsupported roof , relying solely on the " drummy " sound and on their judgment and experience as to whether the roof will stay in place for one hour or for several hours . With but few exceptions , men who had been injured by falls of roof or ccal or were found working under loose and unsupported roof , admitted that they knew of the possibly unsafe condition , but it was their opinion that the roof or coal was not loose enough to fall for some time .

May 1, 1931

By Edward M. Kawenski

Float dust deposits in return airways in bituminous coal and lignite mines present a special explosion hazard. Research is in progress at the Bureau of Mines experimental coal mine to evaluate the degree of the hazard and to develop measures for preventing dissemination of dust into the ventilating air current. To determine the extent of this hazard prevailing in operating coal mines, 711 dust samples were collected in 50 mines located in the major coal fields of the United States. The mean quantity of coal and the incombustible content of the dust in the samples were determined. The term "float dust" is used to designate particles smaller than 74 microns in diameter (particles passing a No. 200 sieve) which have settled from the air current. Dust usually found in roadways and in working places is coarser than float dust, and is termed "coarse dust" (particles passing a No. 20 sieve). Variations in amount and incombustible content of coarse dust in a midwestern mine were studied previously.

Jan 1, 1963

By E. J. (Kirk) Conway

Thirty-five years ago underground coal mining equipment consisted of simple but rugged machines powered by electric motors and hydraulics. The machines were maintained by maintenance personnel armed with a basic knowledge of hydraulics, electricity, and mechanical design. Over the years the the machine has been transformed into powerful complex mining systems. The maintenance burden has also increased. During this period significant advances have been made in maintainability engineering and system design techniques. Many of these innovations and techniques are applicable to the design of underground mining equipment. The objectives of this project were to; (1) determine the extent to which maintainability design concepts and principles have been applied to the design of underground coal mining equipment, (2) try to assess the impact of equipment design for maintenance on productivity and safety, and (3) develop a maintainability design guideline to enhance the design of new or rebuilt equipment. An equipment design review was completed at ten operational coal mines. Interviews were also conducted with mine management, safety, and maintenance personnel to identify machine specific design advantages and problems. Visits were also made to six original equipment manufacturers to discuss the design of their equipment for maintenance. Volume I presents an overview of the protocol used and a summary of the findings. Volume II includes the maintainability design guide for underground mobile mining equipment.

Jan 1, 1989

By Tyler Blake

This report describes a study designed to evaluate a pro-posed modification in the cap lamp battery cord intented to reduce the incidence of snagging and catching of the cord. A three phase evaluation was performed comparing a prototype with the standard, currently available cord. First, a ?pull test? equipment was run. The second evaluation was a body conformity study. The third evaluation involved subjects performing common tasks in a low seam coal mine simulator. The results of these evaluations clearly demonstrated significant safety advantages of incorporating coiled cord into the design of the cap cord. The coil cord presented less of a snagging hazard, allowed the wearer more time to respond to a snag, and transmitted lower levels of force to the helmet when snagged. The research team recommended that cap lamp cords be commercially developed which incorporate coiled cord at the battery and helmet.

Jan 1, 1980

By A. U. Miller

For many years Illinois has been one of the leading coal producers in the United States and as such its safety record has compared very well with the other large coal producing States , both in tons produced and millions of man -hours of exposure per fatal accident . ( See Table 25 in Bureau of Mines Bulletin 293. ) During the 10-year period from 1917 to 1926 , inclusive , the average production in the United States per fatal accident was 278 , 109 tons . The aver age for the State of Illinois for the same period was 409,249 tons . Illinois produced 450,464 tons per fatal accident, and in 1928 produced 390,630, tons , or an average of 419,721 tons for the 12- year period from 1917 to 1928 , inclusive . In 1927 During the year 1929 , the shipping mines of the State made a decided improvement in their record over any previous year . Table 1 shows the monthly production and the tons produced per fatal accident . During 1928 and 1929 safety work was actively carried on in Illinois . Safety meetings were held with mine officials , representatives of the State. De partment of Mines , and the United States Bureau of Mines . At these meetings mine hazards and accidents were discussed and remedies suggested for : their elimination in the future . It is believed that first - aid training was to a considerable extent instrumental in reducing accidents and in making the good safety records in Illinois during 1928 and 1929. During these years ( as well as in 1926 and 1927 to a somewhat less extont ) en intensive rirst-aid training campaign was con ducted in Illinois by the officials and members of the United Mine Workers of America , coal companies, State Department of Mines and Minerals , and the U. S. Bureau of Mines , Every first -aid class was made a safety meeting ; where accidents and general safety were discussed freely while teaching first aid. During this time , anproximately 25,000 persons were trained in first aid, and 17 coal companies were issued certificates for having 100 per cent of their employees. trained in first aid. Since January 1 , 1926 , more than 40,000 have received first -aid training in and around Illinois mines , and including those who received training previous to this date , it is believed that at least 90 per cent of the miners in Illinois have received first -aid training . This state ment is based on the fact that the labor turnover in Illinois is not large .

Apr 1, 1931

By Gerald P. Scanlan

Control of the dust produced by continuous mining machines in coal mines is generally obtained by water sprays from fixed nozzles mounted on the frame of the machine in back of the cutting head. Mounting the nozzles on the rotating head of the machine closer to the coal cutting bits may improve the efficiency of dust suppression. To test this concept, respirable dust measurements were made during 39 regular production shifts in an underground mine using a Joy 11CM continuous miner. The equipment used, difficulties encountered, and measurements obtained are described.

Jan 1, 1974

By W. H. Somerton

The basic objective of this project was to determine the permeability of coal fracture systems as a function of effective stress. The detailed steps in accomplishing this objective are given in Article I of the contract under which the work was conducted as follows: Sec. 1.1 The objective shall be to determine the permeability of the coal fracture system as a function of effective stress. At least three bituminous coals shall be studied and at least five samples of each coal shall be tested. The sample size shall be as large as possible to be representative of coal found in the seam; a minimum of four inches is preferred.

Jan 1, 1974

By E. R. Palowitch

Two samples of the Lower Hartshorne (Spadra) bed were collected: A sample of the raw coal with the machine cuttings excluded, and a sample of the machine cuttings exclusively. Analysis of the 5-inch by 200-mesh size fraction of the raw coal, excluding machine cuttings, showed that a product meeting minimum quality specifications could be produced by washing at 1.60 specific gravity, yielding a theoretical 93.7 percent of clean coal. A negligible amount of near-gravity material at the separation gravity indicated an easy washing problem. The sample of machine cuttings had a maximum size of 2 inches and contained about 50 percent ash. Washability tests of the 2-inch by 200-mesh size fraction indicated that a theoretical yield of 30.0 percent of specification-grade coal could be achieved by washing at 1.49 specific gravity. As the machine cuttings represent an estimated 10 percent of the total coal mined, their inclusion in the mine output would increase the theoretical net yield of salable coal by only 3.7 percent. Because the machine cuttings contained a high percentage of sink 1.80 specific-gravity material, they had neither an effect on the separating gravity required to clean the raw coal nor on the difficulty of separation. Gabbing underground versus transporting the cut-tings to the surface for disposal or washing either separately or combined with the raw coal involves a number of practical, economic; and intangible factors; hence, no specific recommendations could be made. A discussion of some of the factors involved in dealing with a similar problem is given by Gandrud and Riley.4

Jan 1, 1962

By George S. Rice

In 1911 the Director of the United States Bureau of Mines instructed the chief mining engineer of the bureau , during an investigation of coal-mine safety conditions in Europe, to ask the directors of the various mine-experiment stations whether they would favor a European conference . The majority of the officials in immediate charge of experiment stations favored the plan , and Victor Watteyne, inspector general of Belgium, suggested that the United States call such a conference to be held immediately after the Eighth International Congress of Applied Chemistry, which was to assemble in New York on September 3, 1912 . Accordingly, invitations were issued by the United States Government to those countries having mine-experiment stations , namely, Austria-Hungary, Belgium, France, Germany , and Great Britain, and to those that contemplated the establishment of such stations , Canada and Mexico . All but Great Britain and Canada accepted ; Mexico designated a representative , who later found it impossible to come. The Government of Great Britain in declining, expressed regret at its inability to accept ; an informal statement was made that the opening of the experimental gallery at Eskmeals , England , occupied the attention of the officials in charge . Delegates were appointed by their respective Governments as follows: Austria-Hungary, Julian Czaplinski , royal mining engineer. Belgium, Victor Watteyne , inspector general of mines . France, J. Taffanel, director of the Lievin experiment station . Germany, Carl Beyling, bergassessor, director of Dortmund experiment station. United States , Charles E. Munroe, consulting explosives expert and George S. Rice, chief mining engineer of the Bureau of Mines . Subsequently Mr. William O'Connor , a mining engineer and mine operator of Wales , who opportunely appeared at the Pittsburgh station with letters of introduction from the South Wales Institute of Engineers and from prominent mining officials of Great Britain , was unanimously invited to take part in the meeting as an unofficial representative of Great Britain . Messrs . Beyling, Taffanel , and Watteyne were met in New York on September 3, by George S. Rice, who accompanied them to Washington, where they were welcomed by Director J. A. Holmes , of the Bureau of Mines , and where , with the delegates to the Eighth International Congress of Applied Chemistry , they were presented to President Taft . Mr. Taffanel was unfortunately called back to France just before the scheduled time of the conference on account of a mine disaster ; the other delegates , including Mr. Czaplinski , convened at Pittsburgh on the morning of September 14. Mr. Rice, representing the Director of the Bureau of Mines , acted as temporary chairman , and called the meeting to order.

Jan 1, 1914

By Julius Roth

Flyrock is the source of most of the injuries and property damage in a majority of blasting accidents in surface mines. A quantitative correlation between shot conditions and maximum flyrock range can be used to define a "blasting area" in which no personnel or equipment should be present during a shot. The approach used was to develop a model that correlates shot conditions and initial flyrock velocities and permits computation of flyrock range from ballistic trajectories. The Gurney formula for velocity of explosively-propelled plates or fragments was adapted to explosively-propelled flyrock from vertical rock faces or from bench tops. The modified Gurney formula was then "calibrated" with measured flyrock velocities from mining and explosives literature. Charts were then developed for possible field use which give maximum flyrock range as function of shot conditions. The model indicates that for flyrock from vertical faces, borehole diameter, minimum burden and height of explosive column define maximum flyrock range for a given explosive, shot in a given rock. For flyrock originating from bench tops, flyrock range appears to be controlled by the distance of the top of the explosive column to the borehole collar, by total explosive load per borehole and, to a lesser extent, by borehole diameter.

Jan 1, 1979

By William M. Knuth

The objectives of this study were the evaluation of the technical and economical feasibility of utilizing color and color infrared aerial photography to satisfy some informational needs for pre-mine planning, mine progress monitoring, and reclamation monitoring. Seven aerial data collection missions were conducted within a two year period over strip mine sites in Pennsylvania. Scales of 1:6,000; 1:12,000; 1:24,000; and 1:48,000 were flown on the first aerial mission. The 1:12,000 was chosen as the optimal scale for the remaining six flights. An extensive literature and legislative review and discussions with strip mine operators identified the informational parameters that could possibly be obtained from aerial photography. Interpretability accuracies were evaluated for parameters in the broad categories of land use, soils, water, vegetation, and geology. Seasonal interpretation characteristics were noted for infrared photography. Man hours for photointerpretation and costs of aerial data collection were monitored closely and incorporated into a cost benefit analysis. Those parameters that could be mapped, identified, or measured with accuracies =75 percent were incorporated into a photointerpretation training manual. An additional analysis was performed to determine the applicability of the interpretation methodologies and results developed for Eastern sites to Western surface coal mining sites. In addition, a separate aerial photographic interpretation manual was produced during this contract. It is intended to be utilized by eastern and midwestern surface mine operators and regulatory personnel.

Jan 1, 1978

During the period 1979 thru 1982, Multi Mineral Corporation conducted a mining research program at the United States Department of the Interior's Bureau of Mines Oil Shale Mining Environmental Research Facility in the Central Piceance Creek Basin, Rio Blanco County, Colorado. The program consisted of mining, environmental and geotechnical research data and the results are described in this report.

Jan 1, 1983

By A. L. Service

In 1965 the Western phosphate industry ranked third after Florida and Tennessee in total mine and marketable production of phosphate rock and phosphate rock products. It has become an important regional industry and, since the close of World War II, it has become important in the national phosphate economy. This report includes an evaluation of the trends and outlook for the Western phosphate industry through 1975 as part of the Bureau's program to determine the rate at which the Nation's mineral resources are being utilized. The first part of this report is concerned with the relationship between the Western phosphate industry and that of the United States and the world. It describes the principal phosphate deposits and discusses production, export, and import of phosphate rock and marketable products. The second part of the report is concerned with the Western phosphate industry and discusses trends and outlook through 1975. Projections for the utilization of phosphate rock, phosphate fertilizers, and elemental phosphorus have been developed and extended through 1975 in an effort to provide data and information pertaining to the rate of depletion of the Nation's phosphate resources.

Jan 1, 1967

By Robert L. Anderson

A shaft or slope bottom is that portion of a mine that is contiguous to the bottom of the main hoisting shaft or slope. It includes the terminal tracks for loaded-and empty-car storage, locomotive run-arounds, locomotive shops, charging stalls, supply rooms, pump rooms, waiting rooms, and offices for dispatcher, weighmen, and foremen. This paper will deal principally with the arrangement of tracks and the handling of cars on the bottom, but includes other data that may be affected, directly or indirectly, by the bottom lay-out. All of the mines discussed are being operated in comparatively level coal seams.

Jan 1, 1937

By Walter D. Holland

This instructors guide is intended for use in a course which teaches metal and non-metal mine inspectors to perform surveys for inhalation contaminants in above ground metal and nonmetal mine work areas. The handbook entitled "Handbook for Surveys of Inhalation Contaminants in Above Ground Metal and Nonmetal Mining and Processing Work Areas? is used as a manual during the course. The manual contains a survey check list, rules for determining if sampling is required, a list of most frequently encountered contaminants, a list of candidate contaminants and their sampling conditions, and a description of control procedures and devices. There are several experiments in this guidebook which the trainees perform to acquaint them with the sampling systems.

Jan 1, 2011

By Thomas J. Peters

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied a 17,320-acre portion of the 52,143-acre Little High Rock Canyon Wilderness Study Area (CA-020-913/NV-020-008) in order to evaluate its identified mineral resources. The study area is located in Humboldt and Washoe Counties, NV, about 42 miles north from Gerlach. Three areas of epithermal alteration, similar to alteration associated with disseminated gold deposits, were found in the study area. One of the areas occurs along a northeast-trending structural lineament. Southwest of the study area two gold prospects undergoing active exploration, as well JS a gold deposit being prepared for production, occur along the same lineament. The Bureau of Mines examination, however, did not find evidence for gold resources in the study area.

Jan 1, 1987

By A. G. Galaitsis

This report summarizes the work performed under the USBM Contract No. J0245001. The purpose of this work was to expand and improve the scope and accuracy of the method developed under USBM Contract No. J0113056 for the prediction of the number of overexposed workers in the mining industry. A significant portion of the noise data were acquired during mine visits-that took place in the-course of this contract. These data were obtained with time-resolved dosimeters which among other things store a time history of the sampled noise for an eight hour work period. The remainder of the noise data have been obtained from MSHA files and from other BoM-sponsored projects. The report reviews the prediction model, discusses the model's assumptions and approximations, describes the function of the developed software, offers typical examples on the use of the software and includes plots of the newly acquired noise data records.

Jan 1, 1986

By David L. Bickel

The following instructions and descriptions are presented in two parts to assist an individual to make the borehole deformation gage transducer, and to assemble and test the three-component borehole deformation gage. This Bureau 8 of Mines three-component borehole deformation gage (4, 8, 11)2 fits in a 1-1/2-in-diameter borehole that is drilled in rock and then overcored to determine rock stress.

Jan 1, 1978