Search Documents

By S. H. Ash

THE information obtained by examining and analyzing the core drillings from 15 diamond-drill holes shows that with the proper equipment little difficulty should be experienced while sinking the shafts at the 15 selected sites. Although a number of holes penetrated formations containing a high percentage of silica,, the health hazard from dust can be removed by using proper dust-control equipment. Methane was detected in small amounts in only one (hole 5) of the boreholes. The methane hazard should present no difficulty if adequate ventilation is employed while sinking the shafts.

Jan 1, 1952

By D. A. Larson

The Bureau of Mines conducted basic experiments to study the process of crack propagation with a wedge indenter. The work was conducted under plane stress conditions in a hard, brittle limestone. The purpose of these experiments was to first gain an understanding of the basic crack propagation process under a sharp indenter, and second, to determine how the crack propagation process could be used to improve mechanical fragmentation systems. Three methods of rock fracture with the wedge indenter were investigated in this program. These were the confined indentation tests, the unconfined splitting tests, and the edge chipping tests. The confined indention tests represent worst case conditions for crack growth and formed the lower bound on fracture efficiency. The unconfined splitting tests represented best case conditions and fixed the upper bound of fracture efficiency. The edge chipping tests represented an idealized fragmentation process based exclusively upon the highly efficient fracture propagation process. Edge chipping achieved a specific energy of 25 in lb f/in3 compared to conventional drag cutters, which required a specific energy of at least 2,385 in·lb f/in3? Thus edge chipping is up to 100 times more efficient than conventional drag cutting. Because of these promising results, more work is planned with the fracture propagation process in three dimensions.

Jan 1, 1987

By Oliver C. Ralston, Dorsey A. Lyon

The data reported in this bulletin are largely the result of experiments conducted by the Salt Lake City station of the Bureau of Mines in cooperation with the department of metallurgical research of the University of Utah. The work on lead is only one of the phases of the investigations carried on at that station during the years 1914 to 1916. The results of similar work with zinc ores and with copper and other ores will be published in future reports of the bureau.

Jan 1, 1918

The 1963 Lignite Symposium was held on the University of North Dakota campus, Grand Forks, N. Dak., April 30-May 1, 1963, under the cosponsorship of the University of North Dakota and the Bureau of Mines. This symposium, the third in a series, had as a general objective the dissemination of information concerning advances in technology and utilization of solid fuels, with emphasis on lignitic coals. Approximately 150 representatives of industry, government, and educational institutions from 21 states and 3 Canadian provinces were present at the symposium. Those attending were welcomed by Marling J. Ankeny, Director of the Bureau of Mines, representing the Bureau, and Dean T. H. Clifford, Vice President of the University, representing the University.

Jan 1, 1964

The 1963 Lignite Symposium was held on the University of North Dakota campus, Grand Forks, N. Dak., April 30-May 1, 1963, under the cosponsorship of the University of North Dakota and the Bureau of Mines. This symposium, the third in a series, had as a general objective the dissemination of information concerning advances in technology and utilization of solid fuels, with emphasis on lignitic coals. Approximately 150 representatives of industry, government, and educational institutions from 21 states and 3 Canadian provinces were present at the symposium. Those attending were welcomed by Marling J. Ankeny, Director of the Bureau of Mines, representing the Bureau, and Dean T. H. Clifford, Vice President of the University, representing the University.

Jan 1, 1964

By Mark S. Sanders

The present study was designed to explore the contribution of organizational climate and management practices to the injury experience in underground coal mines. A cross-lagged panel design was used in which miners from 22 mines completed questionnaires assessing 27 organizational climate, structure, and function dimensions on two occasions, The results strongly support the hypothesis that climate and management practice have casual effect on the incidence of disabling injuries.

Jan 1, 1976

This report summarizes the results of a research project entitled "Fatal Accident Data Base Development." This project is the last project under Contract No. S0110601. Volumes I and 1I, "Industrial Engineering Study of Hazards Associated with Underground Coat Mine Production," summarize the original industrial engineering project and the Fatal Accident Report Analysis project. These projects were completed and accepted by the U.S. Bureau of Mines on December 10, 1971. Both volumes of the report have been made available by the Bureau to the public through the U. S. Department of Commerce technical information service. Another project under the same con tract, entitled "Equipment Operations Safety Study, ' was completed in January 1972 and the report was accepted by the U. S. B. M. at that time. The analysis in this Natal Accident. Data Lose Development report is closely related to analysis in both of the earlier reports. The original project involved an industrial engineering and safety of production operations for a representative sample of underground bituminous coal mines. The contactor was required to make recommendations 'in work practices, mining methods, equipment, and safety practices which can effectively reduce the fatality rate from rib and roof falls.' (Longwall mining methods were excluded from the study.) Time study and work element analyses were performed in over 50 mines as part of the field data gathering effort. Another requirement of the study was to develop sets of multiflow. Process charts, which are diagrammatic illustrations of the time-related interaction of mining, cycle job elements.

Jan 1, 1972

By Alastair M. Lumsden

A study was initiated to examine the ways in which a number of foreign countries classify and regulate metal/non-metal mines which experience problems due to naturally-occurring flammable gases. Twenty countries were selected for study, and useful information was obtained from sixteen of these. Nine countries were visited (five of them twice) to hold meetings with representatives of government mine regulatory agencies and mine operators, and to visit mines encountering methane and other gases (carbon dioxide, nitrogen). In the later stages of the study seven gassy metal/non-metal mines in the United States were visited so as to provide a basis for comparison, and hence the evaluation of both the U.S. and foreign gassy mine regulations. In addition to obtaining copies of the mining laws and regulations of a number of foreign countries, nine foreign gassy mines, and the seven in the United States were documented in as much detail as possible. All this information is presented, along with appropriate conclusions and appendices. The study took two years and three months to complete.

Jan 1, 1983

By Frank E. Williams

This Bureau of Mines report describes 147 known fluorspar deposits in New Mexico and briefly mentions 54 miscellaneous occurrences for which little or no information was obtained. Most miscellaneous occurrences are minor and too poorly exposed to be considered more than prospects. History and production of fluorspar in New Mexico, type of deposition, mineralogy, uses, and grade specifications are discussed. Total mine production of fluorspar in New Mexico is nearly 641,000 tons of various grades of crude ore and hand-sorted material. Fluorspar deposits occur in 13 of the State's 32 counties. Grant, Valencia, and Luna Counties account for 86.4 percent of the total production. During the investigation, 141 deposits were visited. A total of 72 character samples was collected for assay, and 3 larger samples were collected for bench-scale metallurgical tests. Results of these metallurgical tests indicate that an acid-grade product can be obtained with 95 percent recovery of the CaF2 content of the crude ore.

Jan 1, 1966

By Frank E. Williams

This Bureau of Mines report describes 147 known fluorspar deposits in New Mexico and briefly mentions 54 miscellaneous occurrences for which little or no information was obtained. Most miscellaneous occurrences are minor and too poorly exposed to be considered more than prospects. History and production of fluorspar in New Mexico, type of deposition, mineralogy, uses, and grade specifications are discussed. Total mine production of fluorspar in New Mexico is nearly 641,000 tons of various grades of crude ore and hand-sorted material. Fluorspar deposits occur in 13 of the state's 32 counties. Grant, Valencia, and Luna Counties account for 86.4 percent of the total production. During the investigation, 141 deposits were visited. A total of 72 character samples was collected for assay, and 3 larger samples were collected for bench-scale metallurgical tests. Results of these metallurgical tests indicate that an acid-grade product can be obtained with 95 percent recovery of the CaF2 content of the crude ore.

Jan 1, 1966

By K. E. Stanfield

This report presents the results of analytical studies made on two series of oil-shale samples from the Mahogany ledge of the Green River mine the character of the various grades of oil shale that are being mined and processed into shale oil and refined products at the Bureau of Mines Oil-Shale Demonstration Plant at Rifle, Colo. The analytical work was part of a synthetic liquid fuels program being conducted at the Petroleum and Oil-Shale Experiment Station, Laramie, Wyo. The 16 oil shales ranG6d in color from a gray brown ( or a sample that assayed 10.5 gallons of oil per ton to a very dark brown for a sample that assayed 75.0 gallons of oil per ton. In general, the samples were similar as to the types of organic and inorganic matter that they contained but varied widely in the amounts or these constituents. The principal constituents were calcite, dolomite, illite, and yellow organic material, while the minor constituents were quartz, feldspar and plagioclase feldspar, pyrite, marcasite, analcite, opal, black organic material, and small woody fragments. Some micro-fossils, spores and pollen grains were found also.

Jan 1, 1951

By William P. Stroud

Chemical alteration of the compressive strength of sandstone has been investigated by the U.S. Bureau of Mines (USBM). Successful development of this technology would offer an attractive alternative to the methods now used for stress control in mines. Sandstone cores were stressed to failure under uniaxial compression at two different strain rates. Specimens saturated with either distilled or tap water showed an average 14% reduction in stress at failure compared with those dried in vacuum. Samples saturated with dilute solutions of aluminum chloride, hydrochloric acid, and polyethylene oxide showed no statistically significant difference in failure stress compared with those saturated with water. By contrast, compressive strength of the cores was increased some 7% by saturation with the nonpolar solvent carbon tetrachloride. No correlation was found between zeta potential and compressive strength.

Jan 1, 2010

This study relates to continuous face haulage systems in underground coal mines, and was performed by Joy Manufacturing Company for the U. S. Bureau of Mines under the Bureau of Mines Contract No. HO 242025. The effective starting date for this work was June 14, 1974. There were two main reasons for making this study, the first being to find a safer system to move coal away from the face than the currently predominant shuttle car system, and the second being to seek ways to advance the state-of-the-art of continuous face haulage as a means of increasing coal production.

Jan 1, 1975

By John D. Bardill

A cooperative project between the Bureau of Mines, Department of the Interior, and the Montana School of Mines, investigating results of hydraulic systems for transporting sand slurries for emplacement, was begun in August 1955. In such circumstances, the Bureau provides funds for a fellowship leading to a Master of Science degree as well as available instruments, tools, supplies and equipment. The School provides the ore-beneficiating laboratory with its equipment for use as a pilot plant. The success of a hydraulic backfilling method employing mill tailings depends largely upon the physical characteristics of the tailings. One of these characteristics is size distribution, especially in the finer size ranges. When being emplaced underground, almost impervious layers of slimes separate from some types of mill tailings containing a high percentage of slimes and settle on the top of the sand fill. These coatings may be so dense that the water in the slurry cannot percolate through them for proper drainage. Successive layers of fill in a stope, each with an impervious coating on top, sometimes build up a hydrostatic head, creating pressure on the bulkheads. This may cause breaks in the lining material, inducing sand runs and flooding the level and sumps below. Deleterious slimes flocculated and disseminated throughout the sands should help prevent the formation of impervious slime layers, increasing percolation and settling rates.

Jan 1, 1960

Data recently released indicate substantial improvement in mineral industry performance for 1984. Business plans to increase plant and equipment spending in 1984 by 14.8 percent, according to a recent survey conducted by the Commerce Department's Bureau of Economic Analysis (table 1). In contrast, capital spending by all industries declined 4.8 percent in 1983 and 2.3 percent in 1982. The latest estimate of planned expenditures for 1984 is $2.2 billion higher than the comparable estimate based on the survey conducted in late January and February 1984.1/ [ ] Of particular significance to the U.S. mineral industries are the 15.5-percent increase in capital spending planned by manufacturing in 1984 and the planned 18.6-percent increase in spending by durable goods manufacturing, where the largest increases are planned in the transportation equipment (26.4 percent) and electrical machinery sectors (23.5 percent). Capital expenditures in manufacturing declined in both 1982 and 1983.

Jan 1, 1984

By Earl C. Redman

The Juneau Gold Belt, centered on Juneau and approximately 120 miles long by 10 miles wide, stretches from Berners Bay on the north to Windham Bay on the south (fig. D-l). Access within the Juneau Gold Belt is provided by the Glacier, Thane, and North Douglas Highways. The Glacier Highway extends northwest from Juneau for approximately 40 miles to Echo Cove, and the other two roads end 5.5 miles southeast and 12.6 miles west from Juneau, respectively. None of these roads connect with other highway systems and access to other areas is restricted to airplanes, the State ferry system, and commercial barge lines. BUREAU ACTIVITIES The majority of lode gold produced in Alaska came from the Juneau Gold Belt portion of the Juneau Mining District. To evaluate the economic potential of the Gold Belt, the Bureau located 173 mines and prospects within the area. A total of 263 ad its and shafts were found and 56,650 feet of underground workings were mapped. The Bureau collected and analyzed 1,557 samples during the study. In addition, considerable detailed geologic map-ping was done in the vicinity of the mines and prospects from which ore control models were developed.

Jan 1, 2012

By J. S. Hansen

To advance technology that can conserve critical materials, the Bureau of Mines investigated a cast-on hard-surfacing that wear resistance and confines alloy additions to wear-prone surfaces. Wear-resistant material in form is on a polystyrene , the is embedded in a mold of unbonded s and the wear-resistant material is transferred to a cas surface at the time of For low-stress abrasion, derived from high-carbon ferro-chrome had higher wear resistance than did commercially available weld-hard. The microstructure of the was typi-white iron carbides. Free carbon added to the ferrochrome powder produced more M7C3 carbides than did material contained in surfacings made from ferrochrome alone, and improved the wear resistance. Several white iron powders with greatly reduced chromium contents also white iron contain-M7C3 carbides. One derived from white iron powder had wear resistance to that of weld-deposited hard facings. Among the parameters investigated, surfacing thickness was found to have a or influence on diffusion of elements out of the , microstructure, and wear resistance. The results of field tests on bucket-wheel excavator teeth and plowshares with cast-on hard surfacing are given.

Jan 1, 1985

By Albert H. Fay

The first data compiled by the Bureau of Mines relating to coal- mine accidents in the United States were published in Bulletin 69," in which the total fatalities by years and States were tabulated from 1896 to 1912. Since the publication of Bulletin 69, further research has been conducted, with the result that the bureau is now able to publish for the first time all of the fatal accidents described in the State inspectors' reports by States, causes, and calendar years, from the beginning of inspection service to date. For the anthracite mines of Pennsylvania, there is a continuous record since 1870; the records of the Pennsylvania bituminous mines are continuous from 1877, and, with the exception of one year, the Ohio records are complete from 1874 to date. In fact, the records of all of the States, with few exceptions, are complete; and incomplete data for any year may generally be attributed to the fact that no report was published during that year. The magnitude of the coal-mining industry in the United States is such that too much stress can not be placed on the need of safeguard- ing the three-quarters of a million men employed. Although the figures given herein show an appalling record for past years, they are not published for the purpose of proclaiming the high fatality rate of the past. They are a record of experience covering a period of 45 years, showing causes and results of many accidents in the coal mines of the United States. They represent a diagnosis of the hazard of the mining industry, pointing out the principal physical causes of accidents, and make available a body of uniform facts that will serve as a basis of preventive measures for use in future operations. It is with these great purposes in view that the Bureau of Mines presents the classified data in this report. Classification and study of mine accidents on the basis of number of persons killed is common and very old, but fails to throw enough light upon the problem involved. Many serious accidents in mines have no fatal results, hence in a tabulation of fatalities they are overlooked and the real hazard of the industry is not made clear. An accident does not necessarily include an injury that may result therefrom. Such accidents as the breaking of a hoisting cable, an explosion of powder, gas, or dust, a runaway car or motor are all serious. Although no loss of life results, they should be recorded, investigated, and studied to prevent their repetition. No accurate data for the United States are available showing how far the personal element as related to the miner and his co-worker, the mine foreman, or to the superintendent and others in authority, contributes to accidents. Many accidents are due to inexperience on the part of the miner, his failure to heed orders, a misunderstanding of instructions and last, but not least, carelessness of himself or his fellow worker. A foreman or superintendent may fail to give proper warning regarding the conditions of certain parts of the mine; he may not have inspected certain rooms or entries on the day of a mine accident; the mine may not be properly equipped, or the operator may neglect to comply with the inspector's recommendations. There is, therefore, a personal element on the part of both the operator and the miner that must be considered. Legislation and the enactment of compensation laws will make the operator realize the seriousness of the mine-accident situation, when fatalities and injuries are to be paid for in legal tender of the realm. The miner must be educated and made to realize the dangers he encounters; he must learn that self-preservation and the safety of his fellow workmen should receive his first attention; he should cooperate with his employer, his asso- ciates, and the State mine inspector to the end that the mine hazard may be reduced to a minimum. "Cooperation for safety" should be the watchwords of the operator, miner, State inspectors, and all others in any way interested in the mining industry.

Jan 1, 1916

By H. W. Gillett

This bulletin is issued by the Bureau of Mines as a contribution to the increase of safety and efficiency in the preparation and utilization of the mineral resources in the United States. Notable among the drains on these resources are the demands made by the nonferrousmetal industries, and in these the losses occasioned in melting brass and bronze are worthy of particular attention. This statement will be better appreciated by a consideration of the size of the brass industry. MAGNITUDE OF THE BRASS INDUSTRY. According to the Thirteenth Census, in 1909 there were in the United States 1,021 fu-ms that dealt mainly in brass and bronze. This total included jobbing foundries, manufacturing plants that both cast and machine a brass or bronze product, and rolling mills, but did not include iron foundries having nonferrous departments nor the numerous large brass-foundry departments of manufacturing plants that produce the castings used in the manufacture of electrical apparatus, cash registers, pumps, and the thousands of machines that require brass castings for their construction. Penton's Foundry List for 1910 gives about 1,150 exclusively nonferrous foundries and about 2,300 iron or steel foundries that also melt brass. If the rolling mills and. jobbing foundries in manufacturing plants be included, and if due credit be given to the rapid growth of the industry in the last few years, largely through the stimulation of the automobile busi¬ness, it is probable that not less than 3,600 plants are to-day melting brass or bronze.

Jan 1, 1916

By John R. Duda

The Bureau of Mines is developing estimates of capital investment, operating cost, and selling price for underground mines producing bituminous coal by various mining methods. This study estimates the required capital investment, operating costs, and selling prices for two hypothetical mines designed to produce 1.3 and 2.6 million tons per year (MM tpy)3 by using a longwall system in conjunction with a continuous-mining system. The coal properties being mined are assumed capable of sustaining a 20-year production period. Wages and union welfare payments used in this study are those in effect as of December 6, 1975, as set forth under the National Bituminous Coal Wage Agreement of 1974. Costs of materials and equipment are based on January 1976 indexes. Initial capital investment is $34.6 million for the 1.3-MM-tpy mine and $63.5 million for the 2.6-MM-tpy mine. Capital requirements, including deferred investments, were estimated to be $50.8 and $92.2 million, respectively. These figures translate into total capital investments of $38.51 and $34.91 per ton of annual production. Assuming a desired 15-percent discounted cash flow (DCF) rate of return, with Federal income taxes at 50 percent, the required selling prices would be $13.41 and $12.27 per ton for the 1.3- and 2.6 -MM- tpy mines.

Jan 1, 1976