Search Documents

By Lester M. Adams

In 1980, the Bureau of Mines surveyed a group of mine seals in Randolph County, WV, to evaluate their effectiveness for reducing toxic pollutants in mine water discharges. The survey focused on 11 block wet mine seals, but mine seals of several other types were also examined. The seals were installed in 1966 and 1967 in abandoned drift portals by the Federal Water Quality Administration (FWQA), a predecessor of the Environmental Protection Agency (EPA), in cooperation with the Bureau of Mines and other Federal and State agencies, in a project known as Elkins Mine Drainage Pollution Control Demonstration Project. The seals were designed to prevent air from entering the mine portals while allowing mine water to flow out. It was believed that by preventing air from entering inactive or abandoned mines, the formation of toxic pollutants and acid mine drainage (AMD) could be reduced. Evaluation of the seals was based on water flow measurements, water analyses, and visual observations. The Bureau's 1980 data were compared with past data collected by the EPA. Several leaks and failures were observed in the clay seals, as evidenced by apparent blowouts and the absence of vegetation where the mine water surfaced. Analyses of the 1980 data indicated some improvement in the quality of water discharged from many of the wet air seals.

Jan 1, 1984

By Sidney Katell

This Bureau of Mines study estimates capital investment, operating costs, and selling prices for three underground bituminous mines producing coal with annual production ranging from 1.03 to 3.09 million tons. It is assumed that the mines have a 20-year life. Wages and union welfare payments are considered as of December 6, 1974, under the Bituminous Wage Agreement of 1974, and costs for material and equipment are based on 1975 indexes Initial capital investment ranges from $26,498,500 for the 1.03- million-ton-per-year (MM tpy) mine to $67,173,300 for the 3.09-MM-tpy mine. Total capital investment ranges from $37,437,500 to $92,984,300 for the same mines. Corresponding selling prices for the coal range from $14.83 to $13.26 per ton, assuming a 15-percent discounted cash flow rate of return after Federal income taxes.

Jan 1, 1975

By J. W. Thompson

"The Republic of Colombia on December 30, 1919, enacted a new petroleum law. The Act is expressly limited to mineral oil, natural gas, bitumen, wax and fossilized resin and to asphalt intended for export.The law is not only intended to encourage local investors, but to attract foreign capitalists for oil development. Provision is made for a special edition ion of the law in such languages as the Government may deem necessary to give it extensive circulation within the country and abroad. The published editions must contain the provisions of the law relating to alienship and naturalization.All public lands, or what are termed unclaimed lands, are open to flee prospecting for the purpose of discovering the deposits named in the law, A prospector must obtain from the Government a, license which binds him to deliver to the Government topographic plans of the lands prospected, together with reports of their prospective yielding capacity. This license does not vest the li¬censee with any preferential right for contracting or leasing and may be drawn by the Government at any time.If a discovery is made by a licensee of any of the deposits named and he desires to exploit the same, he must present a memorial or application to the Ministry of Public Works, stating:- (a) the location and municipal district in which deposit beds are found; (b) boundaries of the zone of exploitation, which shall not be more than 5,000 or less than 1,000 hectares; (c) the names and nationality of all persons for whom the lease is sought and the action and time within which,they propose to make the exploitation; (d) the name of the corporation and its legal representatives with their residences; (e) if an alien, he must state his willingness to comply with the law relative to alienship and naturalization; (f) agreement to abide by all of the provieions of the law with regard to Government supervision, payment of taxes, rate of lease and causes of forfeiture; (g) the rate of rent or royalty that the applicant offers to pay, together with any other circumstances that may make the proposed lease advantageous to the Nation."

Apr 1, 1920

By C. K. Eilerts

Knowledge of the phase relations of the fluids that exist in the porous spaces of rocks constituting natural petroleum reservoirs and of the behavior of these fluids under various field conditions of operation is essential to the conservation of petroleum and natural gas and to their efficient recovery. The problem of determining whether these fluids are in the liquid or gaseous state and of recognizing the transitions that may take place as the material in the reservoir is subjected to different conditions of pressure and temperature confronts many producers today, especially in certain fields. The subject has grown rapidly in importance since the discovery of and production from deeper reservoirs that have correspondingly higher pressures and temperatures as compared with shallower

Jan 1, 1938

By W. J. Kroll

This investigation was undertaken with the idea of studying a number of unconventional methods for making chromium to determine whether production cost could be lowered and to discuss some of the more recently described processes. These comprise carbon reduction of the oxide in vacuum, nitride dissociation, fusion electrolysis of the chloride, amalgam method, iodide dissociation, calcium reduction of the oxide, hydrogen reduction of the chloride, and reduction of this compound with zinc and with magnesium. Preference is given this latter method, which is shown in a flow sheet. Special attention is given purification of the chloride and separation of the vacuum at about 900° C. A reduction method for the elimination of traces of oxide contained in pure chromium by pure hydrogen obtained from the dissociation of zirconium hydride is described. The various methods are compared in a table in the appendix. Aluminothermic and silicothermic methods for the reduction of chromium oxide and the aqueous electrolysis have been disregarded in this investigation.

Jan 1, 1950

By Gordon E. Green

This report addresses remote monitoring of coal waste impoundments for stability. Existing automated geotechnical monitoring systems are described and reviewed along with details of instruments suitable for such systems. An impoundment in West Virginia which was in the construction stage was instrumented and monitored between July 1979 and may 1981. Sensors which measure surface and subsurface parameters including settlement, horizontal deflection, surface tilt, pore water pressure, seepage, pond level, and meteorological parameters were installed. Data from the 37 sensors were collected by on-site logger and transmitted by telephone to a central processing station in Seattle for recording and interpretation. Difficulties were encountered with telephone and powerline outages and malfunction of electronic units. Detailed descriptions of the design and performance of the system are provided along with evaluation and comparison with other systems. Recommendations for improving and expanding the capabilities of the monitoring system are given.

Jan 1, 1982

By Rita D. Sylvester

"This compilation lists and summarizes publications by Bureau authors published in the regular Bureau of Mines series, in scientific, technical, or trade journals, or in other media; those available from the Bureau of Mines are indicated. Patents issued to Bureau personnel are also listed, and instructions are given on how to apply for permission to use them. One of the outstanding features of this Special Publication is an exhausive subject and author index. IntroductionThe Bureau of Mines was established in the public interest to conduct inquiries and scientific and technologic investigations concerning mining and the preparation, treatment and utilization of mineral substances; to promote health and safety in the mineral industries; to conserve material resources and present their waste; to further economic development; to increase efficiency in the mining, metallurgical, quarrying, and other mineral industries; and to inquire into the economic conditions affecting those industries, The organic act of the Bureau, as amended by Congress and approved February 25, 1913, made it the province and duty of the Bureau to ""disseminate information concerning these subjects in such manner as will best carry out the purposes of this Act.""In accordance with this directive, the Bureau reports the findings of its research and investigations in its own series of publications and also in articles that appear in scientific, technical, and trade journals; in proceedings of conventions and seminar's; in reference books; and in other non-Bureau publications. The number of these reports, the wide range of subjects they cover, and the variety of mediums in which they appear make the kind of list and index presented in this special publication both necessary and valuable. This issue describes reports and articles published during the period January 1, 1970, to December 31, 1974. It supplements the 50-year list of Bureau publications issued from July 1, 1910, to January 1, 1960;2 the 50-year list of articles by Bureau authors published outside the Bureau from July 1, 1910, to January 1, 1960;3 and the 5-year lists of Bureau publications and articles from January I, 1960, to December 31, 1964,4 and from January I, 1965, to December 31, 1969.5 It includes all the material in the four annual lists of Bureau publications and articles from January 1, 1970, to December 31, 1973."

Jan 1, 1975

The inherently explosion-proof mine (EPM) concept is based upon the non-flammability of certain combustible-oxidant-inert gas mixtures, and the effect of partial pressure of gases on physiological reactions. In a properly controlled underground environment, gas explosions are impossible, men can do work, and relatively high concentrations of methane would be permitted. A systems analysis has been performed to examine the physiological, engineering, and economic feasibility of such a concept, and methods and equipment are recommended for maintaining an EPM atmosphere in a bituminous coal mine producing a nominal two million tons of clean coal per year. It is concluded that: engineering feasibility can be demonstrated using subsystems and components that can be designed and built within the present state-of-the-art, that economic feasibility is possible within approximately five years, and that physiological feasibility is sufficiently promising to warrant continued investigation.

Jan 1, 2012

By E. W. Dean, H. H. Hill

Gasoline has become of such commercial and military importance that it is now practically indispensable. This product is of special interest because, in addition to realizing its value, the Nation is learn- ing that the raw materials from which gasoline is obtained are not unlimited. ACTIVITIES OF THE BUREAU OF MINES IN PROMOTING EFFICIENCY IN THE PRODUCTION AND UTILIZATION OF GASOLINE. The Bureau of Mines has directly and indirectly worked for the conservation and efficient utilization of this important product. Some of the bureau's activities have been along lines widely different from those reported in this bulletin. The work of the bureau toward the increase in efficiency of processes for the production and refining of crude oil is too well known to need mention here. Another line of activity in which the bureau has engaged is the collection and publi- cation of statistics on refinery operations. Finally, as immediate preparation for the present bulletin, two surveys of the gasoline mar- keting situation have been made. The primary object of this bul- letin is to make available to the public information obtained in con- nection with these surveys. PURPOSE OF THE GASOLINE SURVEYS OF 1917 AND 1919. Shortly after the United States declared war on Germany the bureau collected gasoline samples in the retail market throughout various parts of the country. Information regarding the sources of these gasolines and the details of marketing them was obtained, and they were subjected to analytical tests which furnished conclusive informa- tion regarding their properties. The information obtained through this survey proved of inestimable value both to the bureau and the United States Fuel Administration, particularly in drawing up speci- fications and in ascertaining the best means of obtaining supplies of particular types of gasoline that were needed. A similar and more extensive survey was made in the months of April and May, 1919, in order to obtain data needed for the revision of the Federal motor gasoline specification. The specification adopted during the war had been the subject of numerous complaints, and it seemed desirable to determine whether or not these objections were valid before attempting revision.

Jan 1, 1920

By Audrey A. Soja

The Bureau of Mines investigated beryllium resources, production methods, and production costs to estimate the quantity of beryllium available for future use. Eight mining districts and 12 deposits are included in the study; lack of data precluded the evaluation of resources from 6 nonproducing and undeveloped deposits. The study revealed that demonstrated beryllium-bearing resources should be sufficient to meet domestic needs and those of other market economy countries (MEC's) well into the 21st century. Total demonstrated beryllium-bearing in situ resources from MEC's are estimated at 118 million metric tons (Mmt) of ore containing approximately 33,000 mt beryllium metal. Approximately 111 Mmt ore containing 29,000 mt beryllium was included in the cost analysis and availability sections of this study. Three Brazilian districts currently produce beryl ore, and one domestic company, Brush Wellman Inc., produces bertrandite ore. Brush Wellman Inc. owns and operates the only MEC facility in the Western Hemisphere for extracting beryllium values from beryl and bertrandite and is the beryllium industry's only fully integrated corporation.

Jan 1, 1986

By Others, C. M. Weld

During the past two years the Bureau of Mines has issued a series of mimeographed reports giving the results of research work and experiments conducted as part of its war minerals investigations. In this bulletin the reports on manganese are presented, which range in scope from the beneficiation of the ore to the utilization of the metal. The bulletin is in eleven chapters, each comprising a separate report, arranged in the order given below. 1. General information regarding manganese, by C. M. Weld. 2. Uses of manganese other than in steel making, by W. C. Phalen. 3. Problems involved in the concentration and utilization of domestic low-grade manganese ores, by Edmund Newton. 4. Preparation of manganese ore, by W. R. Crane. 5. Leaching of manganese ores with sulphur dioxide, by C. E. Van Barneveld. 6. The Jones process for concentrating manganese ores; results of laboratory investigations, by Peter Christianson and W. H. Hunter. 7. Cost of producing ferromanganese ores, by C. M. Weld and W. R. Crane. 8. Production of manganese alloys in the blast furnace, by P. H. Royster. 9. National importance of allocating low-ash coke to the man- ganese-alloy furnaces, by P. H. Royster. 10. Electric smelting of domestic manganese ores, by H. W. Gillett and C. E. Williams. 11. Use of manganese alloys in open-hearth steel practice, by Samuel L. Hoyt. As each chapter was originally prepared as a unit, there is neces- sarily some duplication and overlapping. With certain exceptions, however, each paper is reproduced in practically its original form. In chapter 1, covering certain general phases of the industry, such as uses, specifications, prices, and statistics, the subject matter has been somewhat modified in view of changes in conditions.About 95 per cent of the manganese consumed in the United States goes into the manufacture of steel. The remaining 5 per cent is used in a number of minor industries, the chief of which is the manufacture of dry cells. These minor uses are described in chapter 2. No discussion of the geology of manganese eres is presented, but a short bibliography on the subject is appended. With few excep- tions the manganese deposits of the United States are irregular, pockety, and uncertain. Largely for this reason, mining methods are crude and hardly warrant descriptions. The concentration of manganese ores, however, is an important problem and involves some details not common to other ores. Chapter 3 discusses the concentration and utilization of low-grade ones, notes the relationship of concentration to metallurgical prao- tices, outlines concentrating processes, and treats of commercial problems. In general, as regards concentration methods, manganese ores may be divided into two groups, as follows: (1) Ores permitting mechanical separation of the manganese minerals and the gangue, and (2) ores in which the manganese minerals and the gangues are so intimately associated that separation requires some hydrometal- lurgical or pyrometallurgical process. Heretofore, attention has been confined almost wholly to mechanical separation, chiefly by gravity. In fact, so far as known, all production of concentrates has been by wet gravity methods, although during the war some companies investigated the commercial pessibilities of magnetic separation and reported favorable results, the construction of one magnetic con- centration mill being started. The usual wet gravity methods are described in chapter 4. During the war, the Bureau of Mines undertook investigations of methods applicable to ores of group 2. A hydrometallurgical process involving leaching with sulphur dioxide was studied at the mining experiment station of the bureau at Tucson, Ariz. The results of this work, presented in chapter 5, indicate that the process is metallurgically feasible but the cost makes it unattractive. The results of an investigation of a pyrometallurgical process known as the Jones process are presented in chapter 6. The process, which is still in the experimental stage, was found to be metal- lurgically sound. The manganese product is not a concentrate but an alloy, made directly from a lean unconcentrated ore. The custom- ary method is to manufacture alloys from high-grade ores or from concentrates of leaner ores. A discussion of the costs of ferro-grade manganese ores is pre- sented in chapter 7. This discussion is in general terms only, but should be of use in so far as it relates to competitive conditions.

Jan 1, 1920

By Peter Grandstone, D. A. Jessup, D. B. Taliaferro

"INTRODUCTION Water flooding of oil sands in Texas as a means of secondary recovery of oil has been practiced mainly in the north-central part of the State, which includes the old shallow fields in eight counties, extending south through Wichita and Clay Counties on the Red River into Brown County.The Texas Railroad Commission, is empowered ""to promote conservation and prevent waste in the drilling, completion, operation, and abandonment of oil wells"" and ""to issue regulations necessary for fulfillment of these ends,"" granted The Texas Co. the first permit to inject water into the oil-bearing sand on December 7, 1935. The permit was granted after the Commission had conducted a number of hearings, which were attended by many operators interested in that method of secondary recovery. Through December 31, 1944, the Commission had granted 50 permits for water flooding. Of that number, 45 permits were issued for projects in north Texas, the remaining 14 being distributed throughout west and south Texas. By the end of 1944, there were 33 active and 5 abandoned water-flooding projects in the North Texas area, as is in figure I.Oil production in the North Texas area started in 1904 from the shallow sands (ranging from 100 feet to 800 feet in depth) of the Petrolia (or Henrietta) field in northern Clay County. Development was rapid and unrestricted during the boom period from about 1911 to 1918, and considerable waste of both produced oil and reservoir energy resulted."

Jul 1, 1946

By B. R. Mohal, S. Chander

"A new technique to determine wettability of powders is presented in this paper. In this technique the times for immersion of individual particles from air into liquids, defined as imbibition times, are measured. Through the measurements of imbibition times for a large number of particles, it is possible to determine homogeneity/heterogeneity of a powder sample with regard to its wetting behavior. Quartz particles give a very narrow distribution of imbibition times showing a homogeneous wetting surface whereas coal particles give a broad distribution indicative of the heterogeneous nature of its surface. The imbibition time measurement technique is considered to have certain advantages over other methods to determine wettability of powders in surfactant solutions. In this study we have also compared the imbibition times with the wetting rate mea¬surements obtained by a modified Walker test.INTRODUCTIONSeveral methods are available for determining wetting characteristics of sol¬ids. Each of the methods has been used in the past to obtain very valuable information for comparing wetting behavior of various solids in a given liquid or for comparing the wetting behavior of several liquids for a given solid. Each method measures a somewhat different aspect of wetting and therefore quantitative correlations between techniques have been difficult. A general approach is to use a method in which close similarity between the technique and the application (where results of wetting measurements are to be used) can be maintained. The objective of this investigation was to develop a method which could be used to determine the wetting characteristics of single particles in surfactant solutions. Wetting of individual particles is of importance in cap¬ture of dust particles by sprays of surfactant solutions.METHODS FOR DETERMINING WETTING — A BRIEF REVIEWThe various methods available for measuring wetting characteristics of solids include: contact angle, immersion/sink time, bubble pick-up, induction time, capillary rise, and displacement method measurements. Some of the methods are briefly reviewed in the paragraphs that follow."

Mar 1, 1989

By Edward L. Tullis

Numerous widely distributed pegmatites of the southern Black Hills of South Dakota contain small amounts of beryl, and two minor deposits are known in the northern Black Hills. Few mines have produced more than 50 tons, and the current, rate of production for the area is about 100 tons annually. Total production, since the first records, is 2,358 tons. Most of the deposits contain less than 1 percent beryl, although the beryl zones in several deposits contain 2 percent beryl or more. Estimated reserves of beryl total 11,824 tons, and an additional 234 tons has been measured; there are other unestimated reserves. The pegmatites are in a belt about the margin of the Harney Peak batholith in the southern Black Hills, although they fail into three districts. The most important, from the point of view of production and reserves, is the Keystone district. Many deposits also are found in the vicinity of Custer and Pringle. Small amounts of beryl occur in the dikes near Hill City. A little beryl has been produced from the Tinton district in the northern Black Hills, and an undeveloped dike has been discovered on Whitewood Peak near Deadwood. The beryl-bearing pegmatites are principally coarse-grained intergrowths or massive segregations of feldspar, quartz, and mica. Some of them contain notable amounts of lithium minerals, as well as some tantalite, columbite, and cassiterite.

Jan 1, 1952

By A. B. Hooker, E. J. Coggeshall

"Dry cells are modified wet primary cells in which the electrolyte is held by absorbent material so that it does not spill aid the cell jars are sealed to prevent evaporation of the absorbed electrolyte. Most dry cells in commercial use are modifications of the Leclanche wet cell. In their usual form they have a hollow cylindrical zinc negative pole that constitutes the containing vessel. An absorbent material, either as a lining in the zinc jar or a bag, separates the zinc cylinder and a rod or flat plate of carbon placed axially inside. A mixture of crushed coke, graphite, and manganese dioxide is tamped about the carbon rod, and the whole mass is saturated with salaanoniac-zinc chloride solution.Dry cells are suitable for services that require minute currents continuously or larger, though limited, amounts of current intermittently. Though limited in this way, they have a wide use, even in underground mining. This paper details some of the applications of dry cells in mines, particularly from the standpoint of greater safety through their use.APPLICATIONSThere are four fields of application of dry cells to mining: (1) Electric shot firing; (2) auxiliary lighting; (3) signaling; and (4) testing.SHOT FIRINGFiring an electric detonator requires very little electrical energy because although the current flow may be 1 to 3 amperes the duration of flow is so small (1 to 4 milliseconds) that the energy withdrawal per shot is almost negligible. Batteries for shot firing need not be large; they may be used for firing either single or multiple shots."

May 1, 1934

By H. H. Schrenk

The purpose of respiratory protective equipment is to prevent the inhalation of harmful or objectionable atmospheres. Although constituents or contaminants that may render an atmosphere irrespirable or objectionable are numerous, they may be classified broadly as follows: I. Gaseous substance: n. A. Toxic. B. Inert (oxygen deficiency). II. Particulate matter (dispersoids). A. Solid. a. Dust (formed by disintegration). b. Pure (formed by condensation). B. Liquid. a. Mist (formed by disintegration). b. Fog (former by condensation).

Jan 1, 1940

Mine drainage and mine reclamation are topics of major interest to the mining industry, federal and local governments, and the general public. This publication and its companion three volumes are the proceedings of a conference held in Pittsburgh, Pennsylvania, April 24-29, 1994. There were twelve sessions (69 papers) that dealt with mine drainage, including modeling, geochemistry, prediction, treatment, control strategies, characterization, hydrology, and case studies. These sessions comprise volumes 1 and 2. The six sessions (34 papers) that dealt with reclamation and revegetation of disturbed lands are included in volume 3. Volume 4 includes the six sessions (34 papers) that dealt with such topical issues as fires at abandoned mine sites, subsidence, hydrology, mine wastes, and policy. Poster session presentations are represented by 49 papers and 92 abstracts that have been placed in the back of volumes 2, 3, and 4, consistent with the subject of that volume.

Jan 1, 1994

This Bureau of Mines publication summarizes the industrial minerals industry of Idaho. It contains information on 119 principal deposits of 21 commodities in the State and describes the institutional and infrastructural factors affecting mineral development.

Jan 1, 1991

By Charles Enzian, Donald F. MacDonald

It is a far cry from the small and uncertain mining efforts of 50 years ago to the splendidly equipped and solidly financed organiza- tions that now handle thousands of tons of ore per day. The old mining was largely speculative; the new is practically on a manu- facturing basis. In the old days of mining the aim was, chiefly, to find comparatively rich ore; modern practice looks more toward efficiency in mining and milling, so that vast tonnages of low-grade material may be worked at a profit. The old operators had faith and hoped for good returns; the new ascertain with a fair degree of precision what the available tonnage is, what the cost of mining and treating the ore will be, the time necessary to exhaust the deposit, the capital required, and the net profits to be made. The old mining was financed on a highly speculative basis, and the value of mining stock was largely controlled by the imaginations of the promoters and of the individual holders. In the new régime the financing of mines is often as conservative as the financing of manufactures or railroads, and the value of stock, quoted on the leading exchanges, is controlled by the carefully estimated profits in sight. Of course, with every legitimate industrial enterprise go certain business risks, and mining is not exempted from these. Then, too, valueless mining as well as valueless industrial stocks are sometimes offered for sale by the intentionally dishonest, or the ignorant. However, the prospective purchaser of a mine nowadays, if he is willing to pay for the services of reputable mining engineers, can obtain information on which to base an opinion as to the quality of his investment. The relatively recent development of cheap and efficient methods of mining and of ore dressing has given value to low-grade ore bodies that a few years ago were almost valueless. The iron mines of northern Minnesota have been fruitful in developing efficiency in mining methods, notably the open-cut methods in which steam shovels strip off the overburden and then load the ore directly into railroad trains for transport to the furnace. In 1907 open-cut mining was applied to the low-grade copper ores of Bingham, Utah, with splendid results, and since then it has won a most important place in the min- ing of large masses of low-grade ores in several other mining regions, especially at Santa Rita, N. Mex.

Jan 1, 1916

By H. D. Hunt

This paper which describes the milling practice of the Miami Copper Co. is one of a series being prepared by the United States Bureau of Mines. LOCATION The mine, concentrator, and other surface plants of the Miami Copper Co. are located near the town of Miami in the Globe-Miami mining district of Gila County, Ariz.

Jan 1, 1932