Search Documents

By R. J. Kuczynski

The U.S. Bureau of Mines operated a 2,000-g (4.4-lb) batch process development unit for recovering platinum-group metals (PGM) from automobile catalysts. Virgin monolith, used pellet, and used monolith catalyst samples were tested. Leaching twice with 1-pct sodium cyanide (NaCN) solution at 1600 C for 1 h dissolved more than 95 pct of the PGM from virgin catalysts and more than 90 pct from used pellet catalysts. More than 85 pct of the PGM was dissolved from used monolith catalysts when a third autoclave step was added. Solid PGM concentrates containing more than 99.8 pct of the dissolved PGM and analyzing greater than 70 pct PGM were recovered by heating the pregnant leach solutions from virgin catalysts to 2500 C and used catalyst to 2750 C for 1 h. The solution after heating contained less than 0.2 ppm. total cyanide. The virgin residues passed the EPA Extraction Procedure Toxicity Test (EP Tox Test), the EPA Toxicity Characteristic Leaching Procedure (TCLP), and the California Waste Extraction Test (WET) for all elements except Ba. Adding sodium sulfate (Na2S04) to the virgin leach residues reduced the amount of Ba dissolved to an acceptable level. The used leach residues passed the EP Tox Test for all elements but failed the WET and TCLP for Pb.

Jan 1, 2010

By Sam S. Taylor

[The discovery of many oil fields in Illinois since 1936 and their rapid development have brought tine problem of brine disposal to the foreground in that State. The ultimate magnitude of the is not yet known, but already it is great enough to warrant technical investigation. The Bureau of Mines, therefore, has made a general survey of the methods of handling oil-field brines in Illinois and has studied in detail three subsurfaces disposal systems.]

Jan 1, 1940

By A. B. Campbell

The mines in the eastern part of the now active region of the Tri-State zinc district of Missouri, Kansas, and Oklahoma have unusually acid water, which during periods of moderate or no rainfall As used in the mills to replace losses from evaporation, seepage, and tailings disposal. Its use has caused difficulties by corrosion of equipment and by interference with flotation. The growing importance of flotation- Which requires good water, and the increasing troubles caused by the corrosion of the milling equipment have prompted the Mississippi Valley Experiment Station of the United States Bureau of Mines, in cooperation with the Missouri School of Mines and Metallurgy, Rolla, Mo., to investigate the action of the waters on flotation and to undertake to develop means of obviating their harmful effects.

Jan 1, 1932

By James S. Browning

[The objective of this project wan to determine the technical feasibility of recovering the associated copper, lead, and zinc from the pyrrhotite axe, of the Great Gossan lead, which has bon pined only for it:, sulfur and iron contents so far. The report constituted a description and discussion of small-scale Preliminary studies. This great pyrrhotite or body has strategic value, inasmuch it contains considerable quantities of zinc, copper, and lead, as well as the iron rend sulfur. The recovery of the: copper, lead, and zinc, associated with certain of the pyrrhotite ore bodies, could augment our domestic supply of these metals.]

Jan 1, 1953

By Sidney Katell

This Bureau of Mines study estimates typical capital investments, operating costs, and selling prices for two bituminous coal strip mines in the Eastern and Interior provinces and a subbituminous coal operation in the Northern Great Plains province. The annual productions were based on tonnage required to fuel a 250-million-standard-cubic-foot-per-day, high-Btu gas plant. The annual tonnage for the Eastern province mine is 4.8 million tons; for the Interior province mine, 6.72 million tons; and for the Northern Great Plains province mine, 9.2 million tons. It is assumed that the mines have a 20-year life. Wages and union welfare payments are considered as of December 6, 1974, under the terms of the Bituminous Wage Agreement of 1974, and costs for material and equipment are based on 1975 indexes. Initial capital investment varies: $65,137,900 for the 4.8-million-ton-per-year (MM tpy) mine in the Eastern province, $78,514,600 for the 6.72-MM-tpy mine in the Interior province, and $42,050,100 for the 9.2-MM-tpy mine in the Northern Great Plains province. Total capital investments for the Eastern province mine, the Interior province mine, and the Northern Great Plains province mine are $86,969,900, $109,378,500, and $78,543,500, respectively. Corresponding selling prices for the coal, per ton, are $6.94, $6.03, and $3.39, assuming a 15-percent discounted cash flow rate of return after Federal income taxes. These studies are considered typical for the areas involved. Costs will vary depending on specific locations in these areas.

Jan 1, 1976

Toward the goal of maximizing minerals and metals recovery from domestic resources, the Bureau of Mines, U.S. Department of the Interior, has conducted in situ corrosion studies at the Salton Sea Known Geothermal Resources Area (KGRA) in the Imperial Valley, Calif., to evaluate and characterize materials of construction for geothermal resources recovery plants. General-, pitting, and crevice-corrosion characteristics of 13 commercially available alloys were investigated for periods of 15 and 30 days in seven process environments expected to be found in typical geothermal resources plants. Stainless steel alloy 29.4, Inconel 625, and the Hastelloys G, S, and C-276 were the most resistant to general corrosion, did not pit, and exhibited little susceptibility to crevice corrosion. Stainless steel alloys 430, E-Brite 26-1, and 6X had low general corrosion rates, but pitted and were susceptible to crevice corrosion. Stainless steel alloy 316 L had a low corrosion rate, but corroded intergranularly, pitted, and was susceptible to crevice corrosion and to stress-corrosion cracking. Titanium-1.5 nickel and TiCode-12 had low corrosion rates, did not pit, and were not susceptible to crevice corrosion. Carbon and 4130 steels had high corrosion rates, pitted, and had high susceptibilities to crevice corrosion. The major scale-forming mineral on the corrosion samples in most of the process environments studied was galena mixed with lesser amounts of other minerals.

Jan 1, 1979

By T. M. Garland

This report presents a more extensive perspective of the calculated profitability of developing and producing crude oil and associated natural gas by primary methods from selected onshore areas of the United States. Estimates were made for cost of drilling, completing, equipping, and producing oil wells at four depths in seven onshore producing areas. A computer program was developed for calculating the discounted cash flow rate of return for the 64 different models in each area resulting from varying the oil-producing rate and production decline rate. The results of these calculations provide data that vividly illustrate the change in rate of return to changes in well depth, initial producing rate, and production decline rate, as well as to variations in development cost and operating expense. Cost per barrel of oil produced in terms of annual cost and total cost is also discussed. Included in the report are explanations of the method of determining costs and the procedure used for profitability analysis. Summaries of all cost estimates and results of profitability analyses are presented in the appendix in tabular form for each of the seven producing areas.

Jan 1, 1972

The Objective: To reduce the noise generated by the exhausting air from a pneumatic roof bolting drill to a maximum of 90 decibels. Any attachment used for this purpose must be lightweight and must not cause a significant increase in back pressure. The Approach: Absorb the noise with a properly designed muffler that will permit sufficient airflow without affecting the normal operation of the drill. How It Works: The air exhausted by the drill enters the muffler through perforated disks into a resonator chamber. It then passes through a series of expansion and contraction chambers and is expelled to the atmosphere through another perforated disk. The basic muffler design for the pneumatic drill was established by using both digital computer analysis and experimentally simulated noise tests. The measured parameters used in the computer program consisted of inlet and outlet pressures, temperatures, airflows and exhaust areas. United

By Terry Muldoon

In conventional noncoal, room-and-pillar mining, the cutting machine is frequently a major source of airborne dust. Water is often used for dust control. An evaluation of typically used water systems during this program showed that they reduced dust levels by 60 to 70 percent over dry cutting when at least 0.5 gpm of water was applied. These systems, however, are only marginally effective in maintaining compliance levels and the added moisture causes operational problems. During the program, three additional dust control systems were designed, fabricated, and evaluated. The first, a hollow cutter bar, was designed to capture dust in the kerf at the cutting zone. The system was only marginally effective in reducing dust levels due to its lack of control of other sources. Large quantities of material captured by the system made it operationally questionable. The second, a machine mounted exhaust system, was extremely effective in capturing virtually all the dust generated in the heading. The captured dust was ducted out of the heading and exhausted downstream in the crosscut. Exhausting the dust without scrubbing, however, creates problems for personnel working downstream of the cutting machine. Successful application would require changes to the mine ventilation system and mining sequence. The third, foam, injected foam from an onboard generator through a channel to the cutting zone at the tip of the bar. Test results showed that foam, using 1/3 to 1/2 the total fluid quantity, was equally effective when compared to the mine's current water system.

Jan 1, 1983

By M. Hayashi

The Bureau of Mines conducted laboratory studies on Idaho mudstones to examine techniques for extracting vanadium. Recovery of vanadium from low-grade sources could contribute to future vanadium production and reduce reliance on imports. An Idaho mudstone surface sample containing 0.30 pct V205 and an underground sample containing 0.21 pct V205 were used in the extraction tests. Leaching of the surface sample for 18 h at 800 C with the addition of up to 1,000 lb/ton H2S04 recovered 70 pct of the vanadium. How-ever, leaching of the underground sample under the same conditions re-covered only 47 pct. By adding 15 wt pct NaCl and roasting the samples at 7500 C for 2 h, followed by leaching with 800 lb/ton H2S04, vanadium extractions were increased to 78 pct from the surface sample and 83 pct from the underground sample. Water leaching of samples roasted at 7500 C for 4 h with a 25-wt-pct NaCI addition yielded about 60 pct of the vanadium from both surface and underground samples. Autoclave leaching at 2000 C for 3 h with 1,000 Ib/ton H2S04 extracted 97 pct of the vanadium from the surface sample and 86 pct from the underground sample. An exploratory solvent extraction investigation to purify and concentrate vanadium in the leach solution using several organic reagents was also conducted.

Jan 1, 1985

By S. M. Runke

"During the past three years the Bureau of Mines has carried on an extensive research program at the Rolla Laboratory for the beneficiation of low-grade Arkansas baixites by ore dressing methods. As a result of this study a 50-ton pilot mill was designed and constructed at Bauxite, Arkansas, by the Bureau to continue the investigation on a semi-commercial scale. The built both to reduce the experimental work to practice and to obtain operating data that cannot be determined by laboratory or small scaleTen samples of bauxitic material were mined and stockpiled at the plant site to ensure an ample supply of material for milling in the pilot plant. These samples were obtained from various bauxite deposits in Saline and Pulaski Counties, Arkansas. The deposits were selected as typical of a wide range of bauxitic material which would necessitate treatment under different conditions and by various concentration methods. All of the samples contained a higher silica content than permissible in Bayer-grade bauxite and several contained so much iron oxide that the available alumina content of the ore was mate¬rially lowered. From data obtained by milling operations on these ten samples, milling characterietics of most of the ores in the district should be predictable. This paper summarizes the results obtained in the laboratory testing of representative samples of each stock pile, and the results of small scale continuous testing of the composite sample of the ten stock piles in the gravity-flotation pilot plant at the Rolla Laboratory."

Aug 1, 1946

By Richard A. Dick

Eight blasts were fired in a 2-1/2-ft bench in the Stewartville member of the Galena Limestone formation in an aggregate quarry near Stewartville, Minn. The shots were dimensionally proportional to production-size bench blasts and were about 5 to 10 percent of full scale. The effects of site, timing of initiation, and burden-to-spacing ratio were studied in a 2 x 2 x 2 factorial experiment, using three boreholes, caw;, containing a 1/2-in charge diameter of high-density ammonia dynamite, in each blast. Detonation velocity measurements indicated that the dynamite detonated satisfactorily in the 1/2-in charge diameter. The effects of the three experimental variables were analyzed by weight for the percentage of oversized material produced and for size distributions determined by screening the entire muckpiles. The bench faces were painted before each shot in an effort to determine the origin of the oversized material. The square pattern (burden and spacing = 15 in) produced finer overall fragmentation and less oversized material than the rectangular pattern (burden = 15 in; spacing = 22-1/2 in). Sites 1 and 2 were about ft apart. Although site 2 produced slightly better overall fragmentation than site 1, the amounts of oversized material produced showed no significant difference. The timing of initiation (instantaneous or delayed) did not significantly influence the overall fragmentation or the amount of oversized material produced.

Jan 1, 1973

By H. C. Miller

"Introduction**The progress of the ""Safety First"" movement in the oil fields of California during the past few years has been remarkably rapid. It has been generally concede by those who have learned to value the life and limbs of their employees, that safety is essential to efficiency and no company that has a high accident rate can be considered an efficient organization. Accidents have a destructive effect on the morale of any body of workers and cause disorganization and delays.The increasing danger to life and limb involved in the drilling for and the production of oil and gas, has become so great that it is clearly evident that everything possible must be done to keep it within the narrowest possible limits.There is a tendency toward carelessness, especially by men who are employed in hazardous occupations. This is brought about by the familiarity of the risk under which they are working and in no industry is this more forcibly exemplified than in the oil fields. Men have performed the same or similar duties for many years and have worked around similar hazards and unprotected machinery until many have can entire disregard for the dangers surrounding then. Very often familiarity with a hazard occasions a contempt for that hazard which only too often results disastrously."

Dec 1, 1923

Multiple-seam interactions are a major ground control hazard in many U.S. underground coal mines. In some U.S. coalfields, particularly in central Appalachia and the West, the majority of today’s mines are operating above and/or beneath previously mined seams. The effects of multiple-seam interactions can include roof falls, rib spalling, and floor heave. These can seriously disrupt mining operations and threaten the safety of miners. In early 2006, a West Virginia coal miner was killed by rib roll that occurred in a high-stress zone beneath a remnant structure in an overlying mine. Fortunately, not every multiple-seam situation results in hazardous conditions. Indeed, the vast majority do not. For the past several years, the National Institute for Occupational Safety and Health has been conducting research to develop better techniques for predicting the location and severity of multiple-seam interactions. During this investigation, more than 50 mines were visited across the U.S. coalfields. Nearly 300 case histories were collected and analyzed using multivariate statistical techniques. The study also employed the numerical model LaM2D to estimate the multiple-seam stress, the Analysis of Longwall Pillar Stability (ALPS) and the Analysis of Retreat Mining Pillar Stability (ARMPS) programs to determine pillar stability factors (SFs), and the Coal Mine Roof Rating to measure roof quality. The study focused on the two most common types of multiple-seam interactions: • Undermining, where stress concentrations caused by previous full extraction in an overlying seam is the main concern; and • Overmining, where previous full extraction in an underlying seam can result in stress concentrations and rock damage from subsidence. The study confirmed that overmining is much more difficult than undermining, and isolated remnant pillars cause more problems than gob-solid boundaries. For the first time, however, it was possible to quantify these effects in terms of the equivalent thickness of interburden needed to compensate for them. The study also found that pillar design is a critical component of multiple-seam mine planning. Many of the failed cases involved pillars whose SF seemed inadequate once the multiple-seam stresses were accounted for. Weaker roof was also found to significantly increase the risk of multiple-seam interactions. The most important result of the study is an equation that predicts the critical thickness of the interburden required to minimize the likelihood of a multiple-seam interaction. This equation was incorporated into a step-by-step methodology that allows mine planners to evaluate each potential interaction and take steps to reduce the risk of ground control failure. Such measures could include installing cable bolts or other supplemental support, increasing the pillar size, or changing the mine layout to avoid the remnant structure entirely. These Proceedings also contain several previously published papers that cover other facets of multiple-seam mining research. Two papers describe the LaModel family of software developed by Professor Keith A. Heasley of West Virginia University. The LaModel programs were designed for calculating the stresses and displacements in coal mines or other thin, tabular seams in layered media. The original three-dimensional version of LaModel is essential for detailed analyses of complex multiple-seam scenarios. LaM2D, by contrast, implements a simplified two-dimensional model that is suitable for quick approximations of the multiple-seam stresses and strains. Three additional papers in these Proceedings describe the extensive multiple-seam experience of the Harris Mine, examples of extreme multiple-seam mining from the central Appalachian coalfields, and longwall mine experiences in Pennsylvania, West Virginia, and Utah. The final paper reports on a numerical modeling study that provided some insight into the mechanics of multiple-seam mining.

Jan 5, 2007

By Forrest T. Moyer

INJURY experience and employment data are presented in this chapter for metal and nonmetal mines, stone quarries, sand and gravel pits, iron blast-furnace slag plants, and metallurgical plants (including ore-dressing and nonferrous reduction plants and refineries) in the United States. Employment and injury experience data for all mineral industries are given in volume II. The 1962 figures are preliminary summations which are subject to revision. They were compiled from all reports from producers received by the Bureau of Mines through April 15, 1963. The data for metal, nonmetal (except well and brine operations), stone, and sand and gravel operations were collected by a mandatory reporting system under the provisions of the act of September 26, 1961, Public Law 87-300 (75 Stat. 649). The act authorized the Secretary of the Interior to study the various aspects of safety in metal and nonmetal mines (excluding coal mines) and report the findings 2 years sub-sequent to the enactment of the law. Data on nonmetal well and brine plants and nonferrous reduction plants and refineries were reported voluntarily by the operators. METAL MINES Preliminary data for the metal mining industry comprise reports on 1,871 mines and pits. The combined fatal and nonfatal injury-frequency rate was 31.95 per million manhours in 1962, a decrease of 8 percent from the similar rate of 34.54 in 1961. Metal operations reported a total of 61 fatal and 3,201 nonfatal injuries.

Jan 1, 1963

By William H. Lesser

Never before have mine managers in the anthracite region of Pennsylvania been so seriously concerned about the rising cost of pumping mine water. Many of them know that future pumping charges may affect their operating profits adversely to an extent that will make it necessary to abandon some mines. Increased pumping charges in the anthracite industry are currently comparable in importance with higher mining costs; in fact, profitable operation of some mines depends not only upon the cost of mining coal but also upon whether they can be kept free from water at reasonable cost. Pumping charges are relatively low during the early development of a mine, but they increase rapidly as development progresses. Numerous crop falls, strippings, and. abandoned adjacent properties contribute unfavorably to the volume of water produced during mining. The foregoing conditions and the existence of large underground pools below existing mining levels present water problems of such magnitude and cost that some mine owners cannot continue to operate profitably.

Jan 1, 1950

By W. W. Adams

With production of coal per man-hour of work highest in history, the coal mines of the United States established a lower accident-frequency4 rate in 1942 than in any year since 1930, the first for which the Bureau of Mines, United States Department of the Interior, collected complete reports of nonfatal as well as fatal injuries. Reports from mine operators and State mining departments showed that 530,861 men were employed in and about coal mines during the calendar year 1942. This number does not include office employees or coke-oven workers. The figure represents a decrease of 15,831 men from the previous year, owing to losses of men to the military services and to more lucrative employment in the munitions and other industries. The loss of men was offset to some degree by an increase in the number of days of mine activity and the average number of hours of work per man during the year. The volume of work done during 1942 was 910 million man-hours, 11 percent more than in 1941. The average employee worked 243 days, 30 days more than in 1941. Production reached the unprecedented total of 640 million short tons, an increase of 12 percent over 1941; 582 million tons came from the bituminous fields of the United States and 58 million tons from the anthracite fields of Pennsylvania. To produce this quantity of coal 1,471 men sacrified their lives, and 69,564 men suffered nonfatal injuries that disabled them for more than the remainder of the day on which the accident occurred. The nonfatal injuries were divided into three groups: 65 caused permanent total disability, 2,045 caused permanent partial disability, and 67,454 caused temporary disability of 1 day or more but did not result in the loss of, or permanent loss of use of, any part of the body.

Jan 1, 1944

By Kenneth D. Winters

This Bureau of Mines report presents a Fortran IV computer program for the structural analysis of (1) protective canopies used in underground mines to protect equipment operators from roof falls and (2) rollover protective structures (ROPS) used in surface mines to protect equipment operators during vehicle overturn accidents. The program, entitled PLASTIC CANOPY, permits rapid and inexpensive calculation of the ultimate strength and deformation characteristics of a canopy for a variety of static loading conditions. The structure is modeled as a series of interconnected beam and/or plate elements. Stresses in, and displacements of, each structural element are computed and printed out at the yield strength of the canopy, at several intermediate load levels between the yield and ultimate strength of the canopy, and at the ultimate strength of the canopy. Other features of the program include prediction of buckling of a beam member under combined axial compression loading and bending, plotting of the input geometry of the structure, and plotting of the deformed shape of the loaded structure. Program description, input instructions, program listing, and four example problems are included.

Jan 1, 1979

By S. A. Bortz

This report presents the results of an extensive laboratory testing program to determine the physical properties of shotcrete including the use of fast-set agents, controlled set cements, and both wet and dry shotcreting equipment. Shotcrete was placed under simulated field conditions using the dry and wet processes. Mechanical properties obtained for accelerated and nonaccelerated shotcretes include compressive, flexural, and shear strength, elastic modulus and Poisson's ratio, and shear and tensile properties of shotcrete bonded to coal, sandstone, and shale. Physical properties measured were unit weight and permeability to methane gas. The data show that rapid setting shotcrete has the potential for improved coal mine ground control. There is no clear evidence that either wet or dry process shotcrete is superior to the other; however, indications are that regulated set cement is preferred to cement containing fast-setting admixtures.

Jan 1, 1973

By Albert H. Fay

Through the hearty cooperation of the State coal-mine inspectors, the bureau is able to present in this paper a a complete statement of the coal-mine fatalities occurring throughout the United States during the calendar year 1919. The reports received from the inspectors for the year just closed show a reduction of 10.58 per cent in coal-mine fatalities as compared. with 1918, while in 1918 the reduction was 4.3 per cent from 1917 figures. The total number killed was 2,307 in 1919 and 2,580 in 1918, a reduction of 273. There was a decrease of 128, or 25 per cent, in fa tali ties resulting from mine cars and locomotives, and a decrease of 198, or 15 per cent, in the fa tali ties due to fall of coal or rock. Surface accidents show a decline of about 25 per cent as compared with the previous year. There were, however, increases in accidents due to gas and dust explosions and also explosives. There occurred during the year nine disasters in which five or more men were killed, representing a total of 201 fatalities. The worst disaster of the year was the one occurring at the Baltimore Tunnel No. 2, Wilkes-Barre, Pa., resulting from the explosion or burning of a number of kegs of powder, by which 92 lives were lost. This disaster emphasizes the need for stricter regulations relating to hauling men and explosives into the mine at the same time. The question of whether electricity was responsible or not does not affect the consideration of the various dangers which arise in underground transportation and handling of explosiveB. At best the handling and hauling of explo.sives is hazardous and such being the case, no one, other than the necessary attendants, should be permitted to ride in cars or cages transporting explosives. As a result of this disaster, the report b of the coroner's jury to the governor of Pennsylvania brings out some important dangers to be avoided in the use and transportation of explosives.

Jan 1, 1920