Search Documents

By R. V. Ramani, W. Miola, R. Srikanth, S. C. Soboleski

"Dust control in high-production longwalls requires attention to operating practices and ventilation schemes. Several studies have shown that the shearer is the major source of dust on a longwall face. Support movement has not been regarded as a major source of dust in US longwalls. Yet, under certain conditions, 31% of the shearer operator's dust exposure can be due to support movement.Several methods have been developed for the control of shield-generated dust. But the need for better methods is apparent. In this paper, the amount of airborne, respirable dust generated per shield move is estimated from specially designed experiments on longwall faces. Ten experiments were conducted on five longwall faces in four mines. Each experiment involved one face visit and lasted three to six hours. The contribution of shield movement to the airborne, respirable dust concentration immediately downwind of the shield move varied between 0.12 and 1.75 mg/m3 in the five longwall faces. The mass of airborne, respirable dust gener-ated by shield movement was found to vary between 39 and 386 mg per shield move. The results from this study reveal that control of dust from longwall shields requires a combi-nation of approaches involving alternative operating prac-tices, reducing shield dust generation rate, increasing face air flow and decreasing personnel exposure.IntroductionIn 1992, longwall mining accounted for about 36% of US underground coal production, a 240% increase from a decade ago. The absolute longwall tonnages were 46 and 133 Mt (51 and 146 million st), respectively. Compared with room-and¬pillar mining systems, the longwall mining system is charac¬terized by higher recovery, enhanced safety and higher pro¬ductivity.However, personnel dust exposure on a longwall face is higher than in other types of mining. According to Mine Safety and Health Administration (MSHA) data, fewer longwalls were in continuous compliance with the applicable dust standard in 1992 than in 1989.Controlling shearer-generated dust and reduction of per-sonnel exposure to airborne dust have commanded attention in the design of longwall faces, operational practices and ventilation schemes. Studies in the United States and abroad have revealed that support-generated dust can be a major obstacle to compliance under certain conditions (Becker et al., 1989; Bradley et al., 1983; Jankowski and Organiscak, 1983; Jankowski et al., 1990; Organiscak et al., 1985)."

Dec 1, 1996

By J. W. Paul

This report is one of a series of papers on coal mining methods and costs which are being prepared through the sponsorship of the U. S. Bureau of Mines for the purpose of bringing to the industry a knowledge of methods as they are used at the present time, and data on certain features which govern costs, safety, and conservation. The methods employed are, influenced by local conditions with respect to the character and dip of the coal, the nature of the, roof and the thickness of the overburden, and the means employed for roof support and its control.

Jan 1, 1929

By Joseph A. DeCarlo, Eugene T. Sheri dan

The process of converting coal into coke is known as carbonization. Essentially, carbonization is destructive distillation in which the volatile matter of coal is released when coal is heated above its decomposition temperature and passes through a plastic stage before solidifying and forming coke. The mechanics of coke formation are complex, and the specific properties of certain coals that allow them to "cake" or form coke are still unknown. Coke is a hard, cellular, carbonaceous mass, formed by heating coal in the absence of air. It is porous, irregular in size and shape, and is similar in appearance to wood charcoal. Coke, however, is denser, more porous, and more abrasive than charcoal. Coke has been in use for several thousand years. History has recorded its use in Greece before the birth of Christ, and it is thought to have been used in China even before that time. It was not until the l6th century, however, that a method for coking was developed in Europe that subsequent ly evolved into the coking process that is known today. The coke industry in the United States began in the latter half of the 19th century when beehive-coke ovens were built to supply fuel for iron blast furnaces. Before this time, an iron industry fueled principally by charcoal had been in existence for several hundred years. With the depletion of timber resources, coke gradually replaced charcoal as blast-furnace fuel, and by 1875 more iron was made with coke than with any other fuel. Before 1893 a 11 coking was done in beehive ovens. These ovens are refractory kilns with arched roofs, sometimes joined together to form batteries.

Jul 1, 1964

By George S. Rice

"The author was a member of a Commission sent by the Secretary of the Interior to France to investigate developments in mining and metallurgy under stress of war conditions, and also to observe the extent and character of the destruction of the collieries and the steel and iron plants, and methods which were being taken to reestablish them. This commission consisted of F. G. Cottrell, Chief Metallurgist of the Bureau of Mines, Frank H. Probert, Dean of the University of California Mining School, and George S. Rice, Chief Mining Engineer of the Bureau. While conducting this investigation a trip was made to the Saar Basin to observe the conditions there. Following this Mr. Rice acted as advisor on mining matters to the Representative of the Economic Council in an Interallied conference held at Cologne in April 1919, and subsequently visited the mining districts in central and southern France, Belgium, and Great Britain.The Germans, in planning a campaign for world supremacy, had as one of their first objectives the seizing of the important Briey iron ore deposits of France and the coal fields of Belgium and northern France.Large resources of coal and iron have led to the commercial greatness of the countries possessing them, as exemplified by the great development first in England then in the United States, and in Germany when the minette high phosphorus iron ores became useful through the invention of the Thomas and Gilchrist dephosphorizing process in 1878. However, this development was anticipated by the German scientific advisors in 1871, and led to the then known deposit of minette ore in Lorraine being taken from France by Germany.When these ores became available, Germany made such tremendous strides that its minette ore developments were not sufficient and importation of ore was necessary. Meantime France, by drilling, had established the extension of the minette ore field into French Lorraine. Then it was discovered that France had greater resources, while the German resources were being rapidly depleted.Although Germany, in its Westphalian basin, possessed the most important coal field on the Continent, containing the largest resources in coking coal outside of Great Britain, its coal was distant from the sea coast, so it could not be an important factor in the export business. No doubt this fact caused the German Imperialists to look forward: to securing the coal basin of Belgium and northern France for future ocean trade.It was a striking feature in the German conduct of the war that, although the steel and iron plants of Belgium and France and other industrial establishments in the invaded regions of Belgium and France were utterly destroyed, the iron mines in French Lorraine were not destroyed nor materially damaged by the Germans in their retreat, while the destruction in France continued until the day of the Armistice. The other striking fact is that the coal mines Of Belgium were not destroyed. It can only be conjectured whether this was due to President Wilson's threat of retribution, which did not stay their hand in France, or was due to the fact that they did not consider Belgium as a real competitor. It was evident they wished to cripple France industrially when they could not hold these northern provinces."

Dec 1, 1919

By Kenneth Wardell

Criteria have been fully developed for determining the optimum size of oil and gas well blocks. The criteria lead to the formation of well barrier pillars which are, of themselves, inherently stable and take account of variable mine roof and floor conditions. The criteria ensure, through considerations of ground movement, that strains transmitted to well casings, are within tolerable limits of casing specifications. The criteria cater for well barrier pillars in multi-seam mining situations and where previous old mining has taken place. The criteria maintain flexibility in being adaptable to local mine design situations. The criteria are applicable to proposed extraction thicknesses up to 15 feet at depths up to 2,400 feet. The criteria are related to producing wells and to abandoned wells. In the latter connection, various states of well abandonment are recognised.

Jan 1, 1980

By J. Wade Watkins, Joseph W. Horne, Arthur Matzick

"A successful procedure for the recovery of a valuable product from weathered tank-bottom settlings has been developed in the laboratories of the Bureau of lines and used in a field pilot plant. These heavy emulsion settlings, generally regarded by the industry as waste material, have usually been drained into open pits or storage ponds and eventually destroyed.Laboratory examination of the waste material shows it to consist essentially of a ""water-in-oil"" emulsion containing a considerable volume of congealed ""paraffin."" This paraffin is mainly high-melting-point wax; known in the industry as microcrystalline wax, for which there is an increasing demand.Because of the physical properties of this wax, the tank-bottom settlings are not responsive to conventional methods used for demulsifying ordinary crude-oil emulsions.The work upon which this report is based was conducted by the Bureau of Mines in cooperation with -the Kansas State. Board of Health and with special cooperative agreements-with the Cities Service Oil Co, Bartlesville, Okla., and the Bareco Oil Co,. Barnsdall, Okla. The studies were made under the general supervision of R. A. Cattell, chief engineer, Petroleum and Natural-Gas Division, Bureau of Mines, Washington; D. C., and H. C. Fowler, supervising engineer, Petroleum Experiment Station, Bureau of Mines, Bartlesville, Okla., and under the direct supervision of Ludwig Schmidt, senior petroleum engineer, Bureau of Mines, Bartlesville, Okla.Gratefully acknowledged are the assistance and cooperation given by the Cities Service Oil Co. of Oklahoma and especially by M. J. Kirwan, manager of production, and by Q. E. Beecher, general superintendent of production, Bartlesville, Okla., and to members of their staff at Oil Hill, Kans.The assistance and suggestions of V. R. Oakley, general superintendent, E. R. Wiles, director of research, L. G. Willis, field engineer in charge crude-oil supply, and Gerald DeWalt, chief chemist, and his staff of the Bareco Oil Co., Barnsdall, Okla., were of much value in the laboratory and recovery work."

Mar 1, 1946

By J. S. Berber

Bastnasite is a natural fluocarbonate of the cerium group and affords an abundant and high-grade source of the lighter rare-earth elements. As part of a broad research program in rare-earth element technology, the Federal Bureau of Mines directed extensive experimental work to separating and purifying the rare-earth elements in bastnasite. By the use of a combination of techniques--classical chemical, ion exchange, and solvent extraction--the processing of a bastnasite concentrate to obtain the individual rare-earth elements, or groups of elements, was accomplished. A bastnasite concentrate, containing about 60 percent rare-earth oxides, was sulfated with concentrated sulfuric acid to eliminate the carbon dioxide, fluorine, and silica. Calcination at 1,200° F. made the gangue matter insoluble, thus permitting the separation of the soluble rare-earth sulfates. Essentially 100 percent of the rare-earth elements were recovered by this procedure. Since the rare-earth sulfate solution contained only trace amounts of nonrare-earth elements, subsequent separation procedures were simplified.

Jan 1, 1960

By H. Britton

This bulletin is the seventh in the series of petroleum bibliographies published by the Bureau of Mines, Bulletins 149, 165, 180, 189, 216, and 220 being compilations for the years 1915, 1916, 1917, 1918, 1919-20, and 1921, respectively. In this bulletin the same general plan of classification of references has been followed, but several additions have been made. ACKNOWLEDGMENTS Acknowledgment is made to the following organizations for the use of their libraries in the preparation of this bulletin: University of California, Stanford University, California State Mining Bureau, Union Oil Co. of California, Standard Oil Co. of California, and the Mechanics Mercantile Library of San Francisco; acknowledgment for their assistance is also made to H. H. Hill, C. P. Bowie, A. L. Foster, M. J. Gavin, H. C. Miller, E. B. Swanson, and Miss Louise Janssen, all of the Bureau of Mines, and to Miss Elizabeth H. Burroughs of the Union Oil Co. of California.

Jan 1, 1929

By R. S. Dean

"INTRODUCTION The metallurgical research program of the Bureau of Mines has been somewhat disorganized, but generally advanced by the increased activities of the war period. The present report is for the purpose of summarizing the work of the Bureau in this field for the past 15 years and indicating its future plan.Fifteen years ago the Bureau turned from its pioneer work on the physical chemistry of steelmaking to an emphasis on raking a pure steel synthetically, rather than by refining, that is, :producing each of the steel 'constituents in the pure state and combining them by simple melting. Such a procedure permits the use of less high-grade ores, not only of iron, but of the ferroalloy metals, such as manganese and chromium,This program has led to extensive work on iron-ore concentration, agglomeration, reducibility of ores and agglomerates, direct reduction of iron ores and concentrates by a wide variety of processes; special refining processes for iron, the production of pure mangenese, chromium, and cobalt from low-grade ores by electrolytic processes, the production of ferrochromium, ferronickel, and ferronickel-cobalt from low-grade domestic ores, and the development of many special alloys to effectively use the new products.The status of the work in each of these fields and the future program of work, together with a bibliography of papers and patents by the Bureau staff on each of these subjects, are given."

Jul 1, 1946

By Norman] [Seldle

This report describes the development of a mine machinery training system from initial conception through a task and skill analysis, a training system analysis, implementation of a prototype system, and initial validation of the prototype system. The objectives of the training are to improve safety and productivity simultaneously via complete, thorough training. A task and skill analysts was executed for shuttle cars, continuous miners, cutters, loaders, face drills, tractors, and scoops. The prototype training system is for shuttle car operator training.

Jan 1, 1976

By L. E. Cardwell

This Bureau of Mines publication contains routine analyses and related source data for 495 natural gas samples from 21 States and three foreign countries. Of this total, 376 samples were collected during calendar year 1968. The remaining 119 analyses are of samples collected during previous years, but releases granting permission to publish the results Here not received until 1968. All samples were collected as a part of a continuous survey of the free world for occurrences of helium in natural gas. This survey has been conducted in the United States by the Bureau of Mines since 1917 and in late 1965 was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus which are described in Bureau of Mines Bulletins 4863 and 576.4 Ten previous publications have presented results of 8,165 gas analyses made by the Bureau of Hines Helium Activity prior to 1968. The first three, Bulletins 486, 576,6 and 617,7 contain analyses and related source data on

Jan 1, 1970

By K. L. Paciorek

The primary objective of this program was to determine the toxic fume and fire hazard of materials used in the construction of mine stoppings and in the sealing and reinforcing of mine ribs and roofs. The materials investigated were: silicone, phenolic, and isocyanate-based rigid foams, as well as epoxy and acrylate mine sealants. Of the rigid foams tested, the X-156 urethane foam presented the greatest toxic hazard based on toxic load values hydrogen chloride was the main toxic species evolved by this foam. In 'lone of the isocyanate-based compositions was hydrogen cyanide the major component, but its contribution increased with temperature. The FS-24 urethane and Celotex Max-Seal isocyanurate foams had the lowest toxic load values, although these two foams have different applications for in-mine use. Of the two mine sealants tested, the latex /acrylic coating presented the greater toxic hazard with acetic acid being the main toxic species evolved.

Jan 1, 1983

By S. J. Hemberger, F. W. Lee

"This project constitutes the results of a geophysical field investigation undertaken in the mining areas in the vicinity of Marion, Crittenden County, Kentucky.Results were obtained at well-known mines being worked for fluorspar. Of special interest was the determination of mineral trends at such mines, particularly in relation to the fault patterns, because of ore in them.This work also constitutes a comparison between the field information that can be obtained by purely geological means and the additional information obtained by applying geophysical surveys to the same areas.As the mineralization in this area is controlled almost surely by the faults therein, the great importance of locating faults cannot be over emphasized. Accordingly, there has been incorporated herein the analyses as well as the application of electrical resistivity methods for fault determinations.In the western part of Kentucky, particularly in that area designated as the Cave-In-Rock quadrangle by the United States Geological Survey, is located the center of the fluorspar mining district of Kentucky. From the mining as well as commercial viewpoint, this area is of considerable interest and importance. It has been described by Currier4/ as a large structural dome that collapsed, through faulting, into a mosaic composed of a main fault pattern that has a strike to the northeast in sedimentary formations. Accompanying this main fault pattern are a large number of irregular faults. This fault complex is also traversed by a dike pattern that has a regional strike for this region focusing a northwesterly direction. The faulting occurred before the dike intrusions, the latter being composed largely of peridotite rocks. According to Reed,5/ most of the metallic mineralization, composed chiefly of galena and sphalerite, occurs at or near the Intersection of the dikes with the faults, indicating a possible igneous origin of the ore deposits. Reed adds that the fluorspar generally does not follow this rule but may also be found in other portions of the faulted zone not directly related to dike intrusions. The area may be considered of equal interest in the occurrence of lead and zinc and in the occurrence of fluorspar controlled by the faults. Hatmaker and Davis6/ give detailed information concerning the form of the ore bodies and economic factors that control ore production in this area; they also suggest the application of geophysical methods in this territory. Ulrich and Smith7/ also discuss geological details in this area. This area is therefore of interest, whether examined from a large structural point of view or from a very detailed angle. The former will assist in determining the origin of the mineralization and its economic possibilities, whereas the latter will give details concerning fault locations and their geologically and geophysically controlling features. This work was undertaken as a pilot investigation relating to the study of the location of fault occurrences, in which it was attempted to determine the location of faults as well as the fault patterns in certain isolated areas. No effort was made to identify the mineralization from the gouge material in the faulted zones; this problem was left for subsequent investigations."

Jun 1, 1946

By Robert W. Thomas

This paper describing the mining practices at the Ray mines at Ray, Arizona, is one of a series being prepared by the Bureau of Mines on mining practices, method and costs in the various mining districts of the United States. At the present time (1929) all mineral Production of the Ray district comes from the Ray Mines of the Nevada Consolidated Copper Co. The ore body is being worked from two shafts, designated as No. 1 and No. 2. An undercut block-caving method of mining is used, variations of which are employed to fit different conditions. The present method has been developed by making improvements as experience was gained or when conditions changed. Refinements in practice are continually being made. The Ray mine was the first in the Southwest to use a caving system of mining on a large scale.

Jan 1, 1929

By Otto Ruhl

The zinc-lead ore reserves of the Tri-State district of Kansas, Missouri, and Oklahoma, as of December 31, 1947, are estimated at a total of 66,100,000 tons of crude ore containing 2.18 percent metallic zinc and 0.38 percent metallic lead. The Bureau of Mines began estimating the reserves in October 1945 and completed the' work December 31, 1947. A total of 38,900 acres of land representing approximately 5 percent of the area of the district is covered in this report. The work was confined for the most part to properties developed or partly developed by drilling and underground workings, and to acreage sufficiently drilled out to indicate ore of enough tonnage to make a commercial undertaking. The acreage in which ore reserves exist is widely distributed in all three States. A map of the Tri-State area is shown in figure 1. The remaining 95 percent of the area is not necessarily nonproductive but represents, possibilities for future exploration and development of additional mineral resources when and if economic conditions or national necessity encourage such work. Of the total reserves, 41 percent are in Missouri, 38 percent in Kansas, and 21 percent in Oklahoma.

Jan 1, 1949

[ ]

Jan 1, 1981

By Rolland L. Blake

The Bureau of Mines investigated the mineralogy, tonnage, and beneficiating characteristics of oxidized (nonmagnetic) taconite iron resources of the Western Mesabi Range as part of its program to insure adequate future domestic mineral supplies. Magnetic taconite currently provides about 95 pct of Mesabi production, but the large tonnages of oxidized taconite between the magnetic deposits will be needed to help meet future domestic demand for iron ore. Three bulk samples that represent large tonnages from the Western Mesabi Range were selected to determine their mineral composition and liberation by light optical microscopy and to test their beneficiating response. This report describes the mineralogy and liberation characteristics of the three samples of the Biwabik Iron-Formation for 26.5 mi (42.7 kID) from Keewatin to Grand Rapids, MN. (Details of response to beneficia-tion were reported previously.) The samples represent mostly material from the Lower Cherty Member of the Biwabik-Iron Formation, although one sample included some Upper Cherty Member. Minerals of all three samples were quartz (chert), hematite, goethite, and minor to trace amounts of magnetite, iron carbonate, and iron silicates. It was concluded that the oxidized taconites of the Western Mesabi Range represent a subeconomic indicated resource that can be selectively mined and beneficiated as a future large source of iron feed for steelmaking.

Jan 1, 1983

By R. V. Lundquist

The compound 2Na2O?3CaO?5Al2O3 occurs as a minor phase in lime-soda sinters prepared for extracting aluminum from siliceous aluminum-bearing materials. About 99 percent extraction of sodium and aluminum from synthesized 2Na2O.3CaO.5Al2O3 was obtained in solutions of NaOH-Na2CO3 at leaching temperatures of 50° C and above. Extractions in water were low because insufficient NaOH was generated by hydrolysis. Extractions in NaOH solutions were limited to about 80 percent owing to the precipitation of hydrated calcium aluminates. Rapid extractions of 100 percent were obtainable in NaaC03 solutions, but the subsequent rapid precipitation of alumina trihydrate caused losses in alumina recovery.

Jan 1, 1965

By Charles E. Munroe

At the outset of the war the uncontrolled production and possession of explosives obviously became a serious menace to the safety of persons and property and the successful conduct of military opera- tions. Even in the years immediately preceding the entrance of the United States into the Great War explosives were employed in attempts to wreck munitions plants as at Eddystone, Pa., or to inter- rupt transportation and conveyance by demolition of munition-laden cars as at Black Tom Island, N. Y., or by attacks on ships, bridges, and viaducts. Outrages with explosives, such as that which Holt inflicted on the Senate reception room, United States Capitol, were not infrequent, and often caused serious loss of life and injury to persons as well as destruction of property. The regular manufacturers of explosives were keenly alive to this menace and early took such steps as lay within their power to meet it as is shown by the following letter:

Jan 1, 1921

By C. W. Owings

"Ventilation is one of the most important features of coal mining, and if a mine is exceptionally gassy it is often difficult to ventilate it in such a way as to make it safe. The general system of splitting the main air current so that two, three, or more sets of room entries are ventilated by the same current of air does not provide a safe method if non-permissible electrical equipment, such as cable-reel, crab-reel, or trolley locomotives are used on gathering haulage, or if open-type hoist or pump motors are used. The problem has been greatly simplified at the Crucible mine of the Crucible Fuel Co. at Crucible, Pennsylvania.The system is not only applicable to the room-and-pillar method of mining, but it may be adopted for any panel system of mining. There also appears to be a definite application in mechanized mining, where the rapid extraction often results in inadequate attention to ventilation and where the gassiness of the section generally increases because, as compared to hand loading, the methane has less time to drain off. The system to be described should commend itself to coal-mining men.ACKNOWLEDGMENTSThis investigation was made possible through the courtesy of H. J. Nelms, general superintendent. E. M. Marshall, safety inspector, E. G. Sauers, assistant superintendent, and Thomas Mark, mine foreman, assisted in the collection of information."

Sep 1, 1931