Search Documents

By Stephen C. Tadolini, Thomas M. Barczak, Peter (Yunqing) Zhang

A cooperative study was conducted with Emerald Coal Resources, L.P., an affiliate of Foundation Coal Corporation, and the National Institute for Occupational Safety and Health (NIOSH) to evaluate the effectiveness of (partially) pre-driven longwall recovery rooms supported with pumpable roof supports. This paper evaluates the load transfer mechanics associated with the advancement of the longwall face into the pre-driven recovery room and the widening of the room to recover the longwall shields. The results show that the yielding of the panel fender produced uncontrollable convergence that caused yielding of the shields and stiff pumpable roof supports when the face was approximately 10 ft from the recovery room. The shields continued to yield until the face advanced into the recovery room. Convergence in the pre-driven recovery room typically reached 6-8 in once the pumpable supports yielded and shed load through a declining residual load capacity prior to being cut out by the longwall shearer. Roof deformations occurred beyond the 32-ft horizon with total deformation ranging from 2 to 4 in, indicating that standing support was necessary to help control the span as the longwall face advanced into the pre-driven recovery room. Stability improved as the pumpable supports were cut out, thereby reducing the span between the shields and the outby pillars. In the end, the shields were successfully recovered under stable ground conditions. However, a disconcerting discovery was the load shedding of the outby pillars as the recovery room was mined into. It is postulated that this may be due to the progression of the rear “abutment” moving toward the recovery room as the panel fender and standing support in the recovery room yield and shed load. This behavior was not expected with a relatively narrow room that is fully supported with standing support. If this mechanism is indeed occurring, the width of the room and performance of the standing support becomes even more critical. Premature failure of the support can lead to excessive convergence on the shield line that cannot be controlled even with modern shields, resulting in roof instabilities that can lead to catastrophic results.

By T. M. Ruff

A prototype mucking machine designed to operate in narrow-vein stopes was developed by Foster- Miller, Inc., Waltham, MA, under contract with the U.S. Bureau of Mines. The machine, called a compact loader-trammer, or minimucker, was designed to replace slusher muckers in narrow-vein underground mines. The minimucker is a six-wheel-drive, skid-steered, load-haul-dump (LHD) machine that loads muck at the front with a novel slide-bucket system and ejects it out the rear so that the machine does not have to be turned around. To correct deficiencies of the tether-remote-control system, a computer-based, radio-remote-control system was retrofitted to the minimucker. Initial tests indicated a need to assist the operator in guiding the machine in narrow stopes. An automatic guidance system that used ultrasonic ranging sensors and a wall-following algorithm was installed. Additional tests in a simulated test stope showed that these changes improved the operation of the minimucker. The design and functions of the minimucker and its computer-based, remote-control system are reviewed, and an ultrasonic-sensor-based guidance system is described.

Jan 1, 1992

By J. Walden, J. Rhoades, R. E. Miller, R. Gibbs, P. Boman

Accelerometers and pressure transducers, mounted in suspension components, can be used to monitor the ride of haulage trucks. Presently, it is difficult to tell what caused a jolt to the truck using either pressure or acceleration data alone. When information from a global positioning system (GPS) is recorded at the same time as shock pressures or acceleration data, the exact location of an event can be determined. Mine management can then determine what caused the jolt to the truck. This research is part of a National Institute for Occupational Safety and Health (NIOSH) project called "Engineering controls for reduction of jolting/jarring injuries in surface mines." NIOSH is investigating how the work environment of haulage truck drivers can be improved. The US Mine Safety and Health Administration (MSHA) notes that, between 1986 and 1995, 60% of the back injuries were to haulage truck drivers in metal/nonmetal surface mining. Personnel from Phelps Dodge suggested that combining acceleration data with information obtained from a GPS could generate results with a variety of uses. Therefore, researchers at the Spokane Research Laboratory (SRL) began investigating how to tie acceleration and GPS data together. It was originally thought that this tool would be used primarily for road and truck maintenance. However, as research progressed, it became apparent that it would also be useful in providing feedback about equipment operations and identifying unusual causes of jolting. Experimental approach Available components that function well by themselves were linked for the purpose of proof of concept. Using a Modular Mining Systems (MMS) product called Vital Signs, SRL researchers took an Aero-Marine Products (AMP) acceleration recorder and hardwired it to MMS Dispatch equipment already installed on a truck. AMP is one of several manufacturers of acceleration recorders frequently used to monitor freight during shipping. MMS Dispatch is used for production accounting and truck dispatching and uses GPS tracking. Through Vital Signs, an analog or digital alarm signal can be recorded. Steve Rhoades, of MMS, wrote unique code that links the Vitals Signs data and GPS location and stores this data in an ASCII log file. SRL researchers installed the equipment in a Caterpillar 793 haul truck. The result was a working prototype. Figures 1 and 2 show the instrument installation in the truck. Discussion From 8:30 pm on Sept. 14, 1998 until 6:50 am on Sept. 15 1998, 899 jolts above a threshold of 2 g (1 g is the acceleration of gravity. It is either 9.81 m/s2 or 32.17 ft/ s2.) were measured on the test truck. Some sections of the haulage road produced most of the events, while

By Thomas E. Lobb, Harry C. Verakis

This article examines the factors related to injuries due to inadequate blasting shelters and blast area security, and identifies mitigation techniques. The key concepts are:(a) accurate determination of the bounds of the blast area, (b) clearing employees from the blast area, (c) effective access control, (d) use of adequate blasting shelters, (e) efficient communications, and (f)training. Fundamentals are reviewed with an emphasis on analyzing task elements and identifying root causes for selected blasting accidents. Mitigating techniques are presented along with discussions and examples.

By R. G. Gürtunca

Over the past century coal miner safety and health has seen tremendous improvements, the fatality and injury rates continue to decrease while productivity continues to increase. Many of the hazards that plagued miners in the past, such as coal bumps, methane and coal dust explosions, ground fall accidents and health issues have been significantly reduced. The contribution of NIOSH research includes products for prevention and survival of mine fires, methane control measures, design procedure for underground coal mines, methods for excavation surface controls, methods and procedures for blasting, laser usage in underground mines and prevention of electrocution from overhead power lines that have reduced accidents and injuries in underground coal mines. Health research has produced products such as the personal dust monitor, noise abating technologies and ergonomic solutions for equipment operators. Research priorities at NIOSH are set by considering surveillance statistics, stakeholder inputs and loss control principles. Future research in coal mining is directed towards respiratory diseases, noise induced hearing loss, repetitive musculoskeletal injuries, traumatic injuries, falls of ground and mine disasters. The recent spate of accidents in coal mines resulted in the Miner Act of 2006 which includes a specific role for NIOSH in future mine safety research and development. The mine safety achievements in the USA reflect the commitment of industry, labour, government and research organizations to improving the safety of the mine worker.

By Robert J. Tuchman

This report presents the origins of the Bureau of Mines and the evolution of the Pittsburgh Research Center from its inception to its present form. Areas of major research emphasis over the years, as well as administrative reorganizations, are discussed.

Jan 1, 1998

By S. M. Shelton, M. M. Fine, T. L. Johnston

"INTRODUCTION The Bynum property is about 15 miles west of Gadsden and 1 mile north of Walnut Grove, Etowah County, Ala. The ore lies in layers and as irregular masses and pockets in the clay residue from decomposed quartzite and limestone formations to the district.The property has been developed by means of numerous shallow shafts sunk to water level - about 25 foot. Operations are confined to small-scale, selective mining of pockets of high-grade ore. The ore is marketed directly, without beneficiation. The property does not yield a large amount of manganese ores. No estimates of reserve ore tonnages are available.A 206-pound sample was furnished for test. It was taken at random from a stock rile estimated to contain 130 tons of ore. The sample con¬sisted of a mixture of manganese oxides, iron oxides, and siliceous fragments in clay. The manganese occurred largely as soft, unconsolidated pyrolusite and wad. Some hard, crystalline pieces of psilomelane were distributed through the soft material. Small amounts of iron oxides were associated with the manganese oxides. Chert, quartzite, and clay comprised the gangue minerals.Dry analysis of the sample was as follows: 36.0 percent manganese, 6.1 percent iron, 2: .0 percent silica, 1.5 percent calcium carbonate, 0.36 percent phosphorus, 3.0 percent alumina, 2.2 percent barium, and 0.31 percent zinc."

May 1, 1942

To provide operators of large-opening mines with a ventilation planning tool that will help them develop a healthier, safer, and more efficient ventilation system in the underground workplace.

Jan 3, 2006

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature of ash, the free-swelling index, and the Hardgrove grindability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions~ issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor and, if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1956

By Claude W. Sill

In the usual volumetric determination of uranium, the solution containing uranium is reduced in a Jones reductor, yielding a mixture of trivalent and tetravalent uranium; the trivalent uranium is oxidized to the tetravalent state by bubbling a stream of air through the solution. The resulting solution of. Tetravalent uranium is titrated with a standard oxidant, generally sulfatoceric acid, dichromate, or permanganate; It seemed likely that the, same general procedure could be used in determining semimicro quantities of uranium if the conditions affecting the variables involved were understood more clearly than at present. In the method described below, the use of ferric sulfate to oxidize tetravalent uranium allows the titration to be made at room temperature in an essentially colorless solution with sulfatoceric acid. The latter oxidant its turn permits the use of the very stable indicator, ferroin, with its sharp color.., change and exactly reproducible blanks. Solutions of uranyl sulfate were prepared by diluting a stock solution that had been standardized gravimetrically according to the method of Lundell and Knowles (8).3/ Solutions of sulfatoceric acid were prepared according to the directions of G. F. Smith (12) and were standardized against arsenic trioxide in the presence of osmic acid according to the directions of Gleu. The cerium solutions were stored in 18-liter carboys fitted with siphon arrangements so that the bottles did not need to be opened and protected from light in a dark cupboard. Under these conditions, even the 0.01 N solution changed by less than 1 part per thousand over a period of about 6 months.

Jan 1, 1952

By D. Gearhart

Full-scale tests are conducted on mine roof supports using protocols developed by the National Institute for Occupational Safety and Health (NIOSH) using the unique capabilities of the Mine Roof Simulator (MRS). These protocols simulate the loading conditions that the support will be exposed to in an underground mine to determine the performance capabilities and limitations of the support. Some tests are conducted with rigid boundary conditions, creating uniform contact and near ideal axial loading conditions. These tests are used to determine the ultimate performance potential of a support, including the strength, stiffness, and stability. For prop supports where stability is a critical design issue, tests are implemented to induce buckling by a modified end condition, eccentric contact, or biaxial loading. It is important to determine the cpacity of the support design when the support is subjected to unpredictable loading conditions. This paper examines the effect of end conditions and load profiles on prop support performance and applies a new analysis methodology based on eccentric loading to determine a factor of safety for load capacity. Recommendations for installation practices that minimize eccentricity and therefore preserve capacity are also provided.

By Mark Colwell, Christopher Mark

This paper summarises the results of a research project whose goal was to provide the Australian coal industry with a rib support design methodology and software tool that could be utilised by suitably qualified colliery staff. The project was primarily funded by Australian Coal Association Research Program (ACARP) and further supported by several Australian longwall operations. The outcome of the project is a design methodology and software tool called, Analysis and Design of Rib Support (ADRS). ADRS is an empirical technique, which recognises that several geotechnical and design factors affect ribline performance and in addition that operational and safety issues essentially dictate the level of performance required. Therefore, the design recommendations associated with ADRS are specific to the Australian coal industry; however the procedure(s) for data collection and analysis could be applied to other countries' 'underground coal industries. Case history data were compiled from 34 longwall and two bord and pillar operations resulting in 204 case histories with each case history data set being defined by approximately 130 individual data fields. In addition monitoring (incorporating stress cells and extensometers) was undertaken at 10 collieries to assess and quantify the effectiveness of different rib support patterns and hardware on rib performance. The monitoring sites allowed for an improved understanding of the mechanisms of rib failure and degradation in terms of its interaction with the installed support and at the various stages of the mining cycle. The design methodology deals with both mains development and gateroad development specific to Australian longwall mines. This paper focuses on longwall gateroads subjected to abutment loading and in particular the travel road which becomes the tailgate of the subsequent panel. The statistical analyses associated with these cases suggested that the level of rib support should be based primarily on the development height and the pillar stress level. The ADRS software guides users through the design process, allowing them to develop rib support plans based on sound science and a broad base of in-mine experience To the best of the authors’ knowledge ADRS is the first systematic rib support design technique to be developed for any country’s underground coal industry. The development and use of empirical models in mining have substantially contributed to improving safety and productivity. ADRS further demonstrates that empirical techniques are particularly relevant and beneficial in dealing with the complexities of geotechnical design associated with underground coal mining.

Jan 6, 2008

By Susan B. Robertson, Gregory E. Hinshaw

Many injuries are caused each year by rock falls in coal mines. Most of these injuries are not caused by major roof collapses, but from falls of smaller rocks from the immediate top or roof skin. Various surface controls are used in mines to control this surface rock. One that has been found to be very effective is roof screening. Depending on the size of the screen, roof coverage approaching 100%can be achieved. Many mines are reluctant to use screen for primary skin control because of additional costs of time and materials, but others are having great success at both controlling costs and surface rock. Data is presented from two mines that show a dramatic reduction in roof skin injuries when screening is used. Much of this success is due to innovations in roof bolting machines. Four case studies of roof screen experience are presented along with associated costs of materials, impact on bolting advance rates, and potential ergonomic risks. The effects of roof screening on skin control and safety are also included. Finally, this paper will provide information about features of different roof bolting machines that affect production and safety.

By Elaine T. Cullen

Miners, like many skilled blue-collar workers, are not traditional learners. They have not always been successful in classroom-type settings, preferring to learn on the job in a hands-on environment. U.S. law requires that miners have a minimum of 8 hours of safety training annually, plus 40 hours for underground miners and 24 hours for surface miners when they enter the industry. However, miners rarely view this training time positively. In fact, it has been called “safety jail” by many, who regard it as a time to get a little extra sleep While mining has become far safer in the past 100 years, it is still a dangerous occupation. The Office for Mine Safety and Health Research, a part of the National Institute for Occupational Safety and Health (NIOSH), has funded a project for the past 4 years to address this challenge. The purpose of the research was to find a way to develop effective safety training for these people. Miners are born story tellers. They share “near miss” stories, stories about master miners they have known, and stories about how things used to be. These stories not only pass along information about what will happen if a miner fails to respect the mining environment, they also instruct listeners in the culture of mining and the values that it embraces. Stories, it seems, are a way to get safety messages across to miners, especially inexperienced ones, and using older, wiser miners in these stories is an obvious choice. This paper will discuss how a series of training videos was developed, how “master miners” and story lines were chosen, and how the resulting videos have been received in the mining industry.

By Gregory M. Molinda

The Coal Mine Roof Rating (CMRR) was developed 10 years ago to fill the gap between geologic characterization and engineering design. It combines many years of geologic studies in underground coal mines with world-wide experience with rock mass classification systems. Like other classification systems, the CMRR begins with the premise that the structural competence of mine roof rock is determined mainly by the discontinuities that weaken the rock fabric. However, the CMRR is specifically designed for bedded coal measure rock. Since its introduction, the CMRR has been incorporated into many aspects of mine planning, including longwall pillar design, roof support selection, feasibility studies, extended-cut evaluation, and others. It has also become truly inter-national, with involvement in mine designs and funded research projects in South Africa, Canada, and Australia. This paper discusses the sources used in developing the CMRR, describes the CMRR data collection and calculation procedures, and briefly presents a number of practical mining applications in which the CMRR has played a prominent role.

Jan 5, 2007

By Jeff Kravitz, John Kovac, Wayne Duerr

Since 198 1, Federal mining law has required every miner working in underground coal mines to have a self-contained, self-rescuer (SCSR) available for use in emergencies. Some miners that have escaped from fires using SCSR's have reported that they had to remove their mouthpiece to talk during escape, thus compromising the protection afforded by the SCSR. If miners are in thick smoke during an escape, they may have trouble if they become separated from their group. The visibility can be so poor that separation can occur at very short distances. To address this problem, two-way, FM radios were built into the SCSR to improve the ability to communicate should the miners be separated over relatively short distances. The SCSR prototypes built and used in testing included both two-way radios and improved mouthpieces. Comparison studies were conducted using combinations of the new and old mouthpieces, and trials using the radio or not using the radio. Subjective judgments indicate that communication ability was significantly improved using the prototype devices. Communication problems have been encountered with teams using standard voice- powered communications systems. Mine rescue teams perform rescue and recovery work under extremely hazardous conditions, life lines are a standard part of mine rescue team equipment. Leaky feeder and quasi-leaky feeder life line communications systems provide significant improvements over standard systems. These improved systems allow all members of the team to communicate with each other and their base of operations. These innovations will significantly enhance the safety of mine rescue operations.

By J. Chilton

The fact that methane ignitions continue to occur at the mining face indicates that monitoring with machine-mounted methanometers does not always indicate the presence of high methane concentrations. Methane concentrations at the face change quickly due to changes in airflow. By measuring these changes in airflow, it may be possible to predict changes in face methane levels more quickly. Currently there are no techniques or instruments to accurately measure airflow in by the mouth of the ventilation curtain or tubing. Tests conducted in the NIOSH ventilation test gallery compare the data provided by one-, two-, and three-axis ultrasonic anemometers. The effects of changes in airflow direction and turbulence on instrument readings are discussed, and guidelines are given for selecting the type of instruments to be used for monitoring airflow near the mining face.

By Gerald T. Homce, James C. Cawley

Arc flash generally refers to the dangerous exposure to thermal energy released by an arcing fault on an electrical power system, and in recent years, arc flash hazards have become a prominent safety issue in many industries. This problem however, has not been effectively addressed in the mining industry. MSHA data for the period 1990 through 2001 attributes 836 injuries to “non-contact electric arc burns”, making it the most common cause of electrical injury in mining. This paper presents results from several elements of a recent NIOSH study of arc flash hazards in mining, and provides information and recommendations that can help reduce these injuries. Characteristics of past arc flash injuries in mining are first outlined, such as the electrical components and work activities involved (based on MSHA data). This is followed by a review of important concepts and terminology needed to understand this hazard. Next, methods for identifying, measuring, and managing arc flash hazards on a power system are covered, with emphasis on recommendations found in NFPA 70E, Standard for Electrical Safety in the Workplace. Finally, results are presented from a detailed arc flash hazard analysis performed on a sample mine electrical power system using IEEE 1584-2004a, focusing on components and locations presenting severe hazards as well as engineering solutions for reducing the risk to personnel. Index terms – electrical arcing, electrical burns, mining, arc flash hazard analysis

By D. J. Bauer

Oxidation of mixed lanthanide solutions with ozone at pH 4.5 and at ambient temperature resulted in precipitation of 98 percent of the original cerium present. Corresponding cerium purity was increased from 50 to 98 percent. A second ozone oxidation-precipitation step produced cerium of 99.9 percent purity in high yield from the 98-percent-pure material. Alternately, ozonation at pH 6.5 and 85° C differentially precipitated cerium and rare-earth elements heavier than cerium and left 89 percent of the original lanthanum in solution at a purity of 95 percent. Subsequent recovery of cerium from the heavier rare-earth elements in the precipitate was accomplished by dissolving the precipitate in dilute mineral acid and reoxidizing the cerium with ozone at pH 4.5 and at ambient temperature. The filtrate contained an enriched praseodymium-neodymium-samarium-europium mixture that is amenable to separation by ion exchange or solvent extraction.

Jan 1, 1968

By Keith A. Heasley, John L. Ellenberger, Paul W. Jeran

In this paper, a state-of-the-art, three-dimensional, full waveform, microseismic system was used to analyze the rock failure around a deep (> 750 m (2500 ft) of cover) bump-prone longwall panel. The microseismic system consisted of both underground and surface geophones coupled through radio telemetry and a fiber-optic network to produce pseudo real-time detection and location of seismic events surrounding the coal seam. This was the first microseismic installation of this scope at a U.S. coal mine, and the system was intended to help determine the exact strata mechanics associated with the redistribution of stress and the associated gob formation at one of the U.S.’s deepest longwall mines. Overall, 5,000 calibrated seismic events were recorded during the mining of one panel, including a Richter magnitude 4.2 event which occurred inside of the array. Analysis of these events provides a number of notable insights into the rock mass behavior. For instance, the longwall panel was widened during the retreat process, and the mining-induced seismicity shows a distinctly different behavior between the start of the panel, the mining of the narrow part of the panel and the mining of the wider part of the panel. Also, in itself, the acquisition of the ML 4.2 event was a major milestone in geomechanical and bump research. This is the first time that such an event has been recorded with this detail and accuracy at a bump-prone coal mine in the U.S. The analysis of this single event has set distinct new limits on the relationship between mining seismicity and coal bumps.