Search Documents

By H. A. Doerner

From thermodynamic calculations3 Maier predicted that zinc oxide Land methane would react at specified temperatures substantially according to equation (1). (1) ZnO + CH; = Zn (gas) + CO + 2H2 Other reactions that may take place are: (2) CH4 = C + 2H2. (3) ZnO + CO = Zn (gas) + CO2 (4) ZnO + H 2 = Zn (gas) + H2O . Maier predicted that 870°C. would be the critical temperature above which reaction (1) would take precedence over reaction (2) and that reaction (1), at equilibrium, would be substantially complete at or above 927°C.

Jan 1, 1931

By Martin Hertzberg

A comprehensive study of the flammability behavior of air-dispersed coal dust was made using an 8-liter Bureau of Mines system which included the following: (1) An optical probe to continuously monitor the dust concentration; (2) measurements of ignition energy requirements; (3) the use of several narrow size distributions ranging from 3 to 65 µm in average diameter; (4) measurements of the extent of flame propagation based on pressure attained at constant volume, residual O2 content after combustion, and flame and dust surface temperatures. The measured lean limit for near-horizontal propagation of Pittsburgh coal dust was about 135 mg/l (milligrams per liter), virtually independent of particle size. Required ignition energies were hundreds of joules and measured limit flame temperatures were 1,450 to 1,600° K. Data on inerting? requirements with KHC03, rock dust, and NaC1 gave approximately the same results as full-scale explosion tests. The good agreement suggests that the cause of earlier discrepancies between small-scale laboratory data and full-scale mine experiments may not have been the difference in size, but were rather a problem of proper care in isolating and controlling the significant experimental variables and in consistently defining the extent of flame propagation at the limits.

Jan 1, 1979

By F. Fraas, H. H. Storch

"In the second paper 4 of this series, data were presented concerning the decomposi¬tion of polyhalite by saturated salt solutions. It was found that uncalcined polyhalite upon leaching with boiling saturated sodium chloride solutions yielded a brine in which the (K2 Mg) /304 ratio was considerably higher than that obtained from the calcined material, and for this reason appeared more suitable for the production of potassium chloride. It was found, in fact, that the leach liquors from uncalcined polyhalite deposited a mixture of KC1 and NaC1 upon evaporation and subsequent cooling, whereas those from calcined polyhalite yielded mixtures which contained not only potassium and sodium chlorides but also large quantities of glaserite, K3Na (S04)2. Hence it was decided to study the evaporation of the uncalcined poly—halite leach liquor and postpone experiments on the calcined polyhalite liquors until such time as a process for further removal of sulphate was developed.A considerable body of equilibrium data is available in the literature on thesystem K+ Mg++ — Na+ Cl—S04 =,— H20 for temperatures up to 83º C. Owing, however, tothe lack of data other than that corresponding to the invariant points and the complete absence of data for temperatures of 100 to 115°C., and owing to the fact that supersaturation phenomena render unsafe the prediction of the behavior of such a system upon evaporation, it was considered essential to obtain the necessary data by actual evaporation and analysis of the brines thus obtained."

Feb 1, 1931

By R. M. Creamer

Attempts have been made to electroplate titanium and zirconium from aqueous, nonaqueous, and fused-salt electrolytes. Metals were produced only in fused-salt electrolytes, the major product being sponge metal. All other electrolytes gave only partial reduction of the metal ions. Fused alkali borate electrolytes containing titanium salts gave titanium boride powders and coatings of poor adherence. Some of the problems encountered in the deposition of these metals and some of the aspects of titanium and zirconium chemistry involved are discussed. INTRODUCTION Titanium and zirconium are both relatively light, noncorrosive metals with both military and civilian uses. This has led to intensive investigations into the metallurgy of these metals. Both metals are high in the Electrochemical Displacement Series and are difficult to prepare in a pure state. At present they are prepared by reducing their chlorides, using magnesium. Electrolytic reductions have resulted in the preparation of fine powders or sponge of variable quality. It is believed that a good process of electroplating these metals on a baser metal would result in a very desirable product. The objective of the research summarized in this report was to investigate methods of electrodepositing these metals, with the idea of producing uniform, coherent plates. Most of the work was concentrated on titanium, the more abundant of the two metals. A system developed for titanium should be applicable to zirconium owing to their chemical similarity. Information gained from these experiments may also be applicable to the electro-winning of the metal.

Jan 1, 1954

By Thomas E. Lobb, Harry C. Verakis

Significant progress has been made in the reduction of serious injuries and fatalities resulting from mine blasting operations. Despite the progress, injuries and fatalities continue to occur. A leading cause of injuries and fatalities from blasting continues to be inadequate blast area security. Even though significant improvements in technology have been made, insuring adequate blast area security remains a challenge and requires constant vigilance. The advances in technology have created safer blasting products and have improved productivity and economics by enabling large, more efficient and effective blasts. However, as blasts grow larger in size, the complexity of adequately securing the blast area increases even more. Periodically the basic fundamentals involved in blasting safety should be reviewed, particularly for securing a blast site regardless of the size of the planned blast. Factors such as flyrock and toxic fumes must be taken into account to insure the safety of persons and property from the results of a blast. This paper examines the factors related to injuries due to inadequate blasting shelters and blast area security, and identifies mitigation techniques. The key concepts are: (a) accurate determination of the bounds of the blast area, (b) clearing employees from the blast area, (c) effective access control, (d) use of adequate blasting shelters, (e) efficient communications, and (f) training. Fundamentals are reviewed with an emphasis on analyzing task elements and identifying root causes for selected blasting accidents. Mitigating techniques are presented along with discussions and examples.

By R. R. French

The industrial minerals industry in the Atlanta, Ga., area was studied in order to better understand problems associated with exploiting mineral resources in and near metropolitan areas. A method for delineating the Atlanta urban area and its component parts was developed so that the factors affecting the location of the minerals industry could be viewed mere objectively in the urban context. Major attention is focused on the area's dominant crushed stone subindustry Demographic and socioeconomic analysis of the Atlanta, Ga., area shows that expansion of the metropolis and its environs will probably eliminate potential mineral resources from the mineral resource base in the area, and that the expanding metropolis will be the primary determinant of future mining sites. Competition for land is accentuated to varying degrees by the incompatibility of wining operations with residential and other environmental requirements. Areas of consideration are suggested to provide maximum development of land and resources for greatest economic benefits it minimum social cost. Further research is recommended to determine market locations in urban areas, optimum operating levels for industrial minerals plants, and alternatives to surface mining.

Jan 1, 1970

By Robert C. Gabler

Evaluation of incinerated sewage sludge as a secondary resource for aluminum, phosphorus, and minor constituents such as copper and zinc was initiated as part of the Bureau of Mines secondary resource program. The elemental composition of sludge ash for 14 plants in 11 U.S. cities was determined. Comparing industrialized cities with cities where most of the sewage is domestic, significant differences in heavy metal content were noted. Various parameters were investigated affecting the extraction of metals and phosphorus from a typical industrial city sludge ash and from a Palo Alto, Calif., sludge ash with a high precious metal content. Three extraction-recovery procedures for metals and phosphorus using sulfuric acid leaching, ion exchange, and various precipitation techniques were investigated. The last procedure developed was a combination approach using a three-stage countercurrent sulfuric acid leach that recovered most of the economic values from the sludge ash and also removed the leachable fraction of elements of environmental concern.

Jan 1, 1979

By NIOSH Publications

In 2004, 14,478 mining operations reported employment statistics to the Mine Safety and Health Administration (MSHA). Almost half (48.9%) were sand and gravel mines, followed by stone mines (30.4%), coal mines (13.9%), nonmetal mines (5.1%), and metal mines (1.7%).

Sep 1, 2007

By Allan E. Martin, George Glocker, C. E. Wood

"INTRODUCTION As part of a comprehensive investigation of the mechanism of defurization of iron and steel by slags, the Blast Furnace Studies Section, Metallurgical Division, Bureau of Mines, in cooperation with the Institute of Technology, University of Minnesota, has made a study of the forms in which sulfur occurs in blast-furnace slag. This report presents data on the three sulfides most important in iron smelting, namely, ferrous sulfide, manganous sulfide, and calcium sulfide. The tendency of these sulfides to form colloids in the molten slag was determined by an examination of quenched samples with an ultramicroscope.Vogt/ conducted experiments on sulfide silicate melts and examined synthetic blast-furnace slags in a partly crystallized condition. His conclusions were that FeS, CaS, and MnS, or isomorphous compounds, such as (FexCay)S and (MnxCaa)S, were precipitated from the melt, depending on the composition of the slag. In all specimens sulfides were visible and were spherical.Coloration of glass by sulfur also provides indirect information on the nature of sulfur in blast-furnace slags./ There seems to be a general agreement at present among the workers in the field of colored glasses that ferrous sulfide is a strong color producer. Colors that have been attributed to this compound include yellow, orange, brown, blue, and black. Apparently the ferrous sulfide is considered to be dissolved in these glasses. There is no indication that any of them have been examined for a colloidal phase.Lorenz 7/ investigated a single manganese slag in the glassy state and observed a Tyndall beam in an ultramicroscope. His conclusion was that either a manganese compound had precipitated in a finely divided condition or that metallic manganese had volatilized and penetrated into the slag as a vapor and thus formed colloidal particles."

Feb 1, 1941

By Timothy W. Beck

Roof bolter occupations in underground coal mines continue to experience overexposure to respirable dust. One potential source of dust in roof bolting operations is the exhaust from the roof bolter dust collection system. A wet exhaust conditioner (?water box?) has been developed to reduce dust emissions from the exhaust of the vacuum dust collection system on roof bolting machines. The exhaust conditioner consists of a muffler chamber and a water chamber with four internal partitions to direct airflow over the surface of the water. The National Institute for Occupational Safety and Health conducted a series of laboratory tests to assess the respirable dust capture ability of this device as compared to the standard exhaust muffler. To determine the dust collection efficiency, both devices were placed in the exhaust stream of a simulated roof bolter dust collection system. Gravimetric samplers were operated upstream and downstream of the exhaust conditioner and muffler to evaluate the ability to capture both respirable coal and limestone dust. Researchers observed a 41 percent reduction in dust concentrations for the water exhaust conditioner in the laboratory configuration. Significant levels of dust deposition in the sampling chambers may have contributed to this effective capture rate.

Jan 1, 2010

Recommendations from 44 mining industry workshops are summarized and reviewed in the context of Bureau of Mines research and development programs on-going during the period 1974-1977. Approximately 1,000 specific recommendations for research and development are summarized in a systematic and comprehensive format appropriate for review by mining research and development program managers. Relevant Bureau of Mines research programs are briefly described and some opportunities for future research and development are identified.

Jan 1, 1979

By A. T. Iannacchione

Roof-rock instability in advancing sections of underground coal mines is a major contributing factor to accidents resulting in fatalities and injuries. Such roof-rock conditions can also result in loss of production due to additional cleanup time and increased amounts of reject material. The Bureau of Mines is investigating fundamental geologic factors affecting coal mine roof-rock instability in order to develop techniques to predict zones of potential unstable roof-rock. Two distinct directional trends of unstable shale roof-rock in a mine working the Upper Kittanning Coalbed are delineated: one trend is associated with the sandstone-shale transition zone, the other with a fault system. The unstable shale roof-rock associated with the transition zone, a consequence of differential compaction, is comprised of slickensided roof-rock. Whereas, the unstable shale roof-rock associated with the fault system, a consequence of structural deformation of the strata, is comprised of fault planes. These faults, small in comparison to the sandstone-shale transition zone, are difficult to delineate with a standard drilling program. Trends of the transition zone associated with the sedimentary facies change are projected into unmined portions of the coalbed with the aid of exploration core data.

Jan 1, 1981

By L. C. IlsLey

Cooperation between the United States Bureau of Mines and the Safety in Mines Research Board of Great Britain, continuous since 1924, has made possible this and other papers on safety subjects. Grateful acknowledgment is made to representatives of the Safety in Mines Research Board of the Mines Department for their assistance in arranging visits to several mine-safety stations, and to F. H. Wynne, Deputy Chief Inspector of Mines, Great Britain, for arranging visits to mines in Great Britain, Belgium, France, and Germany. During the summer of 1927 the writer had the privilege of visiting the mine-safety testing stations in Great Britain, Belgium, Germany, and France, in the order named. All of these countries have large coal mines, many of which are rated as gassy. Therefore, when the installation of electrical equipment is contemplated, each of these countries is confronted with the same safety problem as in the United States - the development of electrical equipment that will not ignite gassy mine atmospheres, should such atmospheres through neglect or accident surround the equipment. The means used by those countries in safeguarding gassy mines should therefore be of general interest to safety engineers in American coal mines, and it is proposed to give a brief survey for each of the four countries mentioned. The first of these surveys will cover conditions in Great Britain.

Jan 1, 1929

By E. G. Baglin

The Bureau of Mines devised a procedure for selectively extracting platinum-group metals (PGM) and gold from Stillwater Complex flotation concentrate. The Stillwater Complex is the only major U.S. PGM resource. Development of a suitable extraction technique will contribute to its exploitation. The concentrate was roasted at 1,050° C to convert host base-metal sulfides to oxides and the PGM from sulfide minerals to their elemental states. The roasted concentrate was preleached with dilute sulfuric acid to remove easily soluble gangue minerals. After pre-leaching, the concentrate was slurried with 6M HCI and leached at ambient temperature and pressure with a strong-oxidizing agent. Hydrogen peroxide, chlorine, sodium hypochlorite, nitric acid, and a persulfate salt were the oxidants investigated. The two-stage leaching scheme ex-tracted up to 97 pct of the platinum, 92 pct of the palladium, and 99 pct of the gold from the roasted concentrate. The base metals were not solubilized and reported to the residue. No attempt was made to devise a procedure to recover the copper and nickel because they comprise less than 5 pct of the value of the concentrate. Viable techniques for recovering the precious metals from the pregnant solution were sulfide precipitation, cementation with nickel, or adsorption on activated carbon.

Jan 1, 1985

By Wilford S. Wright, Harold E. Heide, Robert S. Sanford

"INTRODUCTION The United States production of tin has always been negligible, and domestic requirements have been met almost entirely by imports. The advent of war in Europe in 1939 brought a threat to our foreign source of supply, and steps were taken by Congress to forestall shortages of tin and other metals. By authority of the Strategic Minerals Act, passed by Congress in 1939, the Bureau of Mines and Geological Survey conducted investigations of domestic tin deposits.An examination of Alaska deposits was undertaken in 1940 and 1941 by J. B. Mertie, Jr., and Robert R. Coats of the Geological Survey.H. B. Heide conducted a preliminary examination of lode and placer-tin deposits at Cape Mountain in 1942, which was followed in 1943 and 1944 by a program of exploration by churn drilling in the placer area and trenching and sampling the lode deposits.Placer tin, found at the head of Goodwin Gulch, Cape Creek, First Chance Creek, and Boulder Creek, indicates that the mineral was derived from the vicinity of lode cassiterite occurrences on Cape Mountain. Placer tin led to the discovery of at least one, cassiterite vein by the Geological Survey and the Bureau of Mines."

Dec 1, 1946

By G. A. Smyres

The Bureau of Mines investigated a HCI-02 leaching procedure to recover Cu, Ni, and Co from a low-grade bulk sulfide flotation concentrate prepared from the Duluth gabbro complex. Since the Duluth gabbro complex is the largest known and unexploited Ni resource in the United States, the development of options for extracting the metal values from the flotation concentrate of this domestic resource is necessary. Conditions were determined for producing a pregnant solution low in Fe to facilitate recovery of the metal values. Leaching experiments were conducted at 15 pct solids, 1000 to 1200 C, 0.2 to 0.3 g HCI per gram concentrate in a 50-gal reactor pressurized to 50 pSig with 02. Base metal extractions from the concentrate were, in percent, 90 to 92 Cu, 99 Ni, 97 to 99 Co, and 0.1 .Fe. Precious metals extractions were erratic and unpredictable; at best their extractions were, in percent, 55 Au, 90 Ag, 40 Pt, and 45 Pd. The reaction time at 1200 C was 0.5 h. The use of compressed air instead of 02 as the oxidant was also investigated. Solvent extraction using LIX 622 was used to remove Cu from the pregnant solution. Cementation on Cu was tested for precious metals recovery, while sulfide precipitation was used to produce a Ni-Co product. A conceptual flowsheet for treating the Duluth gabbro concentrate is proposed.

Jan 1, 1985

By K. O. Bennington

The thermodynamic properties of two manganese silicates, pyroxmangite and fowlerite (zincian rhodonite), were experimentally determined by the Bureau of Mines. The standard enthalpies of formation were determined by hydrofluoric acid (HF) solution calorimetry, the low-temperature heat capacities by adiabatic calorimetry, and the high-temperature heat capacities by differential scanning calorimetry over the range 322 to 1,372 K. Data for the standard enthalpy of formation (AH298), the derived standard entropy (S298), and the standard Gibbs energy of formation (AGf 298) are as follows: Pyroxmangite [(Mn0.9554Cao,0446)(Si03)J- AHf298 319.668±0.46 kcal/mol AH298 (from oxides)... -7.215±0.11 kcal/mol 5295 23.785±0.048 cal/(mol'K) AGf298 -301.190±7.96 kcal/mol Fowlerite [(Mno.7o3Zno.0884Ca0.2086)(Sio3)]--AHf298 ?... -329.914±0.419 kcal/mol AH298 (from oxides)... -8.400±0.104 kcal/mol 5598 21.949±0.059 cal/(mol-K) AGf298 -310.716±7.99 kcal/mol These experimentally determined values were combined with data from the literature to calculate the Gibbs energies and equilibrium constants of formation over the temperature range of the measurements. Standard enthalpies, Gibbs energies, and equilibrium constants of formation are given as a function of temperature from both the elements and the constituent oxides.

Jan 1, 1987

The Department of Interior, U.S. Bureau of Mines performs the task of estimating the quantity of coal reserves existing in each state on a county by county basis. As a part of Information Circular 8655, the Bureau of Mines established the criteria for the uniform estimations of coal reserves and listed the most recent estimates of coal reserves by county and by seam. At the same time however, the Bureau recognized that these figures represented the upper bound with regard to the estimated actually usable or obtainable reserves. Recovery of these reserves are subject to the mining methods used and to the resolution of such problems as the use of poor quality coal and competition provided by conflicting land use. These problems, in practice restrict the recovery of the estimated quantities of coal reserves listed in IC 8655. Another impact, the subject of this manual, is the impact resulting from previous mining activities. In particular, many of the reserve seams included in the reserve estimates overlie or underlie mined-out coal beds. Portions of these reserve seams may therefore be unmineable or at best may have a reduced quantity of extractable coal. In order to improve the accuracy of the coal reserve base estimates, the Bureau of Mines funded an effort1 to develop a systematic methodology for estimating the coal loss associated with the impact of previous mining activity. The coal loss calculation model (CLCM) described in this manual is a result of that effort and addresses the percentage of coal loss in reserve seams due to previous overmining or undermining.

Jan 1, 1976

By Michel C. Frippel

This section of the Minerals Yearbook reviews the minerals industries of 27 countries: the 12 nations of the European Community (Belgium, Dermark/Greenland, France, Germany, Greece, Ireland, Italy, Luxembourg, the Netherlands, Portugal, Spain, and the United Kingdom); 6 of the 7 nations of the European Free Trade Association (Austria, Finland, Iceland, Norway, Switzerland, and Sweden); Malta; the 8 Eastern European economies in transition (Albania, Bulgaria, Czechoslovakia, Hungary, Poland, Romania, and Yugoslavia); and the U.S.S.R. Western Europe Western Europe [loosely defined to include the 12 nations of the European Community (EC) and the 7 nations of the European Free Trade Association (EFTA)] is the single largest trading area and consumer of raw materials in the world. If Western Europe was at one time an important mining sector, it has now increasingly relegated the role of supplying minerals for its minerals processing industry to the more minerally endowed countries in North and South America, Africa, and Australia. In this regard, Western Europe is the most important determinant of raw materials consumption (and thus, indirectly, raw materials production). Western Europe has significant reserves of industrial minerals but has limited availability of metalliferous raw materials. It, therefore, imports significant quantities of the latter and ranks along with the United States and the U.S.S.R. in the production of refined metals. Nonetheless, there is an inherent tendency to underestimate the importance of Western Europe in the world of minerals, both as a minerals processor and raw materials buyer. The reason for this is that Western Europe is generally thought of on the basis of individual nations rather than as a whole. Viewed in this limited context, the United States, the U.S.S.R., and Japan appear to dominate the world economy. Viewed as one regional area, however, Western Europe includes the fourth (FRG), fifth (France), sixth (United Kingdom) and seventh (Italy) largest economies of the world, all bordering on one another. With the remaining 15 EC and EFTA countries, Western Europe has a land area approximately 40 % of that of the United States, exceeds the U.S. population by 50 % and has a gross domestic product about the same as that of the United States.

Jan 1, 1993

By Marvin E. Lane

This paper , which describes the mining methods and practices at the Hayden Creek lead mine of St. Joseph Lead Co. in southeast Missouri , is one of a series being prepared by the Bureau of Mines on mining methods , practices , and costs in various mining districts of the United States . The Hayden Creek mine is in the W 1/2 sec . 7 , T. 36 N. , R. 4 E. , St. Francois County , Mo. , about 1 mile southwest of the town of Frankclay ( fig . 1) . The mine is on the west edge of the mining district known as the Lead Belt . However , neither the ore body nor the underground workings are connected with those of any other mine in the district . In contrast with most operations in the district , underground haulage is entirely trackless , and nearly complete delineation of the large , well -defined ore body by drilling permitted comprehensive planning of development and mining in advance of shaft sinking . The ore differs in character and occurrence from that of the main ore deposits in the Lead Belt in that the lead mineral , galena , occurs in the dolomitic matrix enclosing granite boulders instead of in dolomite limestone .

Apr 1, 1957