Search Documents

By Diana K. Schimmelpfennig

Assessment of revegetation success on mined lands is a difficult, time consuming task and has been the subject of a number of controversies. Present regulations require that both plant cover and aboveground plant biomass be measured for use in making that assessment. Of these two variables, biomass is the most time consuming to measure and requires destructive sampling, a most undesirable requirement on fragile, recently revegetated areas. On the other hand, plant cover can be estimated using the point-frame method which is relatively nondestructive. In addition, vegetation can be sampled more uniformly with the point frame and in less time if species composition measures are to be made. A study was done to evaluate the predictability of aboveground biomass production on revegetated mined sites and adjacent native prairies using plant cover estimates made with the point frame method. The predictability of biomass production by cover estimates bears on the need for both measurements in assessing revegetation success. In general, a positive, statistically, significant correlation was demonstrated between plant cover (estimated by the point frame) and aboveground biomass (estimated by the harvest method) regardless of community type (mined or native), species composition, diversity or level of biomass production. However, the latter did have their effects on the relationship and must be accounted for in any predictive equations (that is to say, the predictive equations must be considered site-specific). Considering the relationship observed between the two parameters, cover estimation may be a sufficient indicator of revegetation success, especially where time and minimization of disturbance are critical.

Jan 1, 1982

By Richard D. Miller

The helium resources base of the United States was estimated by the Bureau of Mines to be 1,070 Bcf as of January 1, 1985. These resources are divided into four categories in decreasing degree of assurance of their existence: (1) helium in storage and in proved natural gas reserves, 280 Bcf, (2) helium in probable natural gas resources, estimated at 243 Bcf, (3) helium in possible natural gas resources, estimated to be 287 Bcf, and (4) helium in speculative natural gas resources, which makes up the remaining 260 Bcf. These helium resources are further divided into depleting, non-depleting, and stored classifications. The depleting resources are those associated with natural gasfields that are, or will be, produced for the natural gas they contain. Almost all of the helium in potential (probable, possible, and speculative) natural gas resources is included in this classification. These depleting resources are estimated to contain 900 Bcf of the total helium resource base. Helium resources contained in nondepleting natural gas resources, those in shut-in, abandoned, or otherwise nonproducing natural gasfields, are estimated to total 133 Bcf. There is 37 Bcf of helium in storage in the Federal Government-owned Cliffside Gas Field near Amarillo, TX.

Jan 1, 1987

By C. H. Fisher

Sulphuric acid of various concentrations has long been used as a reagent in the determination of olefins and aromatics in hydrocarbon oils4 such as gasoline, kerosene, and neutral oils from coal-tar distillates. Despite its long use, however, there is no general agreement as to optimum conditions and concentration of acid, and numerous methods and modifications have been recommended. In most cases, treatment of the neutral oil with 80 to 90 percent sulphuric acid, followed by distillation to the original endpoint to remove olefin polymers, is recommended for the estimation of unsaturated hydrocarbons. The distillate thus obtained is taken as olefin-free oil and used in later stages of the anlysis. Aromatic hydrocarbons generally are determined in the olefin-free oil by suphonation with more concentrated acid (96 to 100 percent and fuming sulphuric acid are recommended), the hydrocarbons not attacked and removed as water-soluble sulphoric acids being considered as saturated hydrocarbons. In some cases the saturates are examined further by differentiating between cyclic (naphthenes) and acyclic hydrocarbons (paraffins), Generally this is achieved by physical methods, although strong sulphuric acid is known to react preferentially with some types of saturated hydrocarbons. It was the purpose of the present work to make a general study of this type of analysis and to investigate the reactions of hydrocarbons under conditions often used in analyses that employ sulphuric acid reagents. Since previous work is not in good agreement, the optimum concentrations of acid for the different stages of the analysis were determined. Several sulphuric acid methods previously recommended and new modifications were compared, two synthetic solutions being used as the reference oil. The results obtained are presented below under separate headings.

Jan 1, 1937

By C. H. Fisher

Sulphuric acid of various concentrations has long been used as a reagent in the determination of olefins and aromatics in hydrocarbon oils4 such as gasoline, kerosene, and neutral oils from coal-tar distillates. Despite its long use, however, there is no general agreement as to optimum conditions and concentration of acid, and numerous methods and modifications have been recommended. In most cases, treatment of the neutral oil with 80 to 90 percent sulphuric acid, followed by distillation to the original endpoint to remove olefin polymers, is recommended for the estimation of unsaturated hydrocarbons. The distillate thus obtained is taken as olefin-free oil and used in later stages of the anlysis. Aromatic hydrocarbons generally are determined in the olefin-free oil by suphonation with more concentrated acid (96 to 100 percent and fuming sulphuric acid are recommended), the hydrocarbons not attacked and removed as water-soluble sulphonic acids being considered as saturated hydrocarbons. In some cases the saturates are examined further by differentiating between cyclic (naphthenes) and acyclic hydrocarbons (paraffins), Generally this is achieved by physical methods, although strong sulphuric acid is known to react preferentially with some types of saturated hydrocarbons. It was the purpose of the present work to make a general study of this type of analysis and to investigate the reactions of hydrocarbons under conditions often used in analyses that employ sulphuric acid reagents. Since previous work is not in good agreement, the optimum concentrations of acid for the different stages of the analysis were determined. Several sulphuric acid methods previously recommended and new modifications were compared, two synthetic solutions being used as the reference oil. The results obtained are presented below under separate headings.

Jan 1, 1937

By O. M. Bishop

From October 1943 to March 1944, the Bureau of Mines conducted core drilling at the Victory fluorspar mine, Hardin County, Ill. to test the Fredonia limestone and the included sub-Rosiclare sandstone zone beneath the existing stopes. Twenty-one vertical holes were drilled to an average depth of 60 feet. Ore was penetrated in six holes. Since its discovery in 1927, the Victory mine has produced approximately 5 percent of the total fluorspar mined in the United states after that date. The ore discovered in the early mine development is now exhausted, except that contained in pillars drifting to the northeast has partly developed one substantial ore body, and company drilling has indicated another nearby. The increasing need for fluorite for war use in 1943 suggested the desirability of mining the pillars, provided it could be established that no ore beds existed below the stopes or in areas to which access would be obtained through the present workings. This work describes the work accomplished during the project and presents the data obtained.

Jan 1, 1948

By L. J. Prosser

The Bureau of Mines has completed an underground degasification project in which an underground piping system was used to transport methane from the coalbed to the surface. In a la-month period four horizontal holes were drilled to an average depth of 1,450 feet. All four holes were surveyed vertically and azimuthally. In 991 days of degasification, 255 MMcf of gas was drained from the coalbed. The underground piping system proved to be a safe and effective means of transporting methane from the coalbed to the surface.

Jan 1, 1981

By H. H. Schrenk

[There is a need for method of determining: benzene vapor in air which is simple and accurate and suitable for making industrial hygiene surveys. The most widely used method in this country is the modification of the Elliott and Dalton6/ procedure. This depends on the nitration of the benzene to reduction to phenylenediamine with all excesses of standard titanous chloride; solution, and titration with e standard ferric ammonium sulphite solution. This method has the disadvantages of being what time consulting: and cumbersome it requires considerable apparatus, and a special modification is necessary in the presence of toluene.]

Jan 1, 1935

By A. G. Loomis

Although secondary-recovery methods have not been applied widely in California, it is apparent that increasing attention and effort must be given to this phase of recovery if the State is to maintain its high rank as a petroleum producer. Steadily increasing demands for petroleum products and decreasing rates of discovery of new oil fields, with rapid depletion of existing reserves, emphasize the prospect of an adverse situation of supply and demand in the not-far-distant future. If the trend of discoveries becomes more favorable or if more complete economic recovery of the oil in place can be obtained by secondary recovery, this situation can be averted. Not only are these reserves of economic importance to the petroleum industry for meeting increasing market demands; but economic reclamation of such reserves is an important conservation measure, which will prolong the productive life of many fields. Accordingly, progressive operators in California are alert to the possibilities of secondary recovery and have done much to implement such operations wherever feasible. Most current operations are of the pressure-maintenance type, in which the reservoir pressure is maintained or partly maintained by injecting natural gas to in-crease oil recovery. The possibilities of recovering additional oil from stripper fields by gas drive and water flooding (including water disposal) also are being tested in experimental field projects. Table 1 summarizes current gas-and water-injection projects in California.

Jan 1, 1952

By T. W. Johnson

One of the common methods of increasing recovery of oil from partly depleted oil sands is to inject natural gas, air, or air-gas mixtures into the sand, thereby supplying energy to move oil into the well bore. Where natural gas is not available, air or an air-gas mixture is used as the repressuring medium. Air-gas mixtures are obtained from the casing-heads of oil-producing wells in the areas repressured with air or air-gas mixtures and consist usually of varying amounts of the hydrocarbon gases, nitrogen, oxygen, and carbon dioxide. Laboratory experiments have been conducted by the Bureau of Mines to determine the effect of air on crude oils.4/ In these experiments the crude oils were oxidized by the air, and the degree of oxidation depended not only upon the chemical composition of the crude oil but also upon the duration and method of contact between the oil and air, the temperature of the fluids and the concentration of the oxygen. When the crude oils were oxidized the following results and changes in the oils were obtained:

Jan 1, 1937

By T. W. Johnson

One of the common methods of increasing recovery of oil from partly depleted oil sands is to inject natural gas, air, or air-gas mixtures into the sand, thereby supplying energy to move oil. into the well bore. Where natural gas is not available, air or an air-gas mixture is used as the repressuring medium. Air-gas mixtures are obtained from the casingheads of oil-producing wells in the areas repressured with air or air-gas mixtures and consist usually of varying amounts of the hydrocarbon gases, nitrogen, oxygen, and carbon dioxide. Laboratory experiments have been conducted by the Bureau of Mines to determine the effect of air on crude oils.4/ In these experiments the crude oils were oxidized by the air, and the degree of oxidation depended not only upon the chemical composition of the crude oil but also upon the duration and method of contact between the oil and air, the temperature of the fluids and the concentration of the oxygen. When the crude oils were oxidized the following results and changes in the oils were obtained:

Jan 1, 1937

By R. J. Leary

The natural gas-air burner described in this report was designed and constructed to meet the thermal requirements of a convective process for heating steel scrap. This process involved downward combustion of natural gas with air, blending the combustion products with diluent air, and then passing this tempered stream of gases downward through a porous bed of steel scrap contained in the furnace chamber. The scrap would be heated to a temperature limited by the adiabatic flame temperature of the gas stream in a period that depended on the rate at which heat was supplied per unit of bed cross section. The temperature of the gas stream would be limited to that beyond which an objectionable degree of oxidation would occur; for carbon steel this limit had been found to vary from 1,900° to 2,100° F. with the superficial velocity of the gas stream. The productivity of the process was dependent on the rate of heat input per unit of furnace cross section; for the 3-foot-diameter experimental furnace an input of 680,000 B.t.u. per hour was desired. The burner described was designed to meet these conditions of temperature and heat input. It provided for three streams of entering gases: (1) A primary air-fuel mixture too rich to be combustible, that is, above the upper flammable limit; (2) secondary air for combustion of the primary mixture; and (3) tertiary air, principally for cooling the combustion products to the temperatures desired for process operation. Downward combustion of the primary and secondary streams occurred in a flame stabilized on an annular port, while tertiary air flowed in an annular path surrounding the port and also through an axial channel whose wall formed the inner ring of the annular port. This burner performed beyond the designed heat-input rates while producing stable flames, which were adjusted readily to the temperatures desired. Gas-stream temperatures were easily controlled to within 15° F. of the desired value by simple manual adjustment of the flow valves.

Jan 1, 1959

By N. S. Dalal, Xiaoya Sun, Xianglin Shi

"The in vivo toxicity of vanadium(V) has been found to correlate with the depletion of cellular glutathione and related non-protein thiols. With a view to understanding the mechanism for this observation, we have investigated the oxidation of glutathione, cysteine N·acetylcystcinc and pcnicil· lamine by vanadium(V), using electron spin resonance (ESR) and ESR spin trapping methodology. The spin trap used was 5,5-dimethyl-l-pyrroline I-oxide (DMPO). It is found that the oxidation of these thiols by vanadium(V) generates the corresponding thiyl radicals and vanadilim- (IV) complexes. The results suggest that free radical reactions play a significant role in the depletion of cellular thiols by vanadium(V) and hence in vanadium(V) toxicity. 1. INTRODUCTIONThis communication reports on the identification of thiyl radicals formed as intermediates in the reaction of vanadium(V) with glutathione (GSH) and related nonprotein thiols. This study was undertaken because the biochemical mechanism of vanadium toxicity is still not fully understood,. despite being a topic of current research activity [1-20). As to possible clues, it is known that vanadium is most toxic when administered in its pentavaient state [21), and that vanadium(V) administration into laboratory mice reduces cellular levels of NAD(P)H and GSH [22). While the oxidation of NAD(P)H by vanadium has been studied extensively [16-20), that of glutathione and related non-protein thiols has been paid less attention. On the other hand, GSH and related thiols are important cellular antioxidants [23). Their functions include decomposing lipid peroxides and protecting cell membranes [23-25). Thus any reduction in the cellular contents of such nonprotein thiols after vanadium exposure may result in the accumulation of lipid peroxides which might ultimately lead to tissue injury. With a view of finding the mechanism for this thiol depletion process, we have investigated reactions of non-protein thiols with vanadium(V). Particular attention has been paid to the detection of thiyl radicals, since it has been postulated [l] (but not experimentally proven) that the glutathionyl radical (GS·) might be an intermediate in the reaction between vanadium(V), NADH and GSH. We have used electron spin resonance (ESR) and ESR spin trapping methodology for investigating the reactions of GSH, cysteine, N-acetylcysteine and penicillamine with vanadium(V). The results show that the corresponding thiyl radicals are indeed formed in the one-electron reduction of vanadium(V) by all of the above mentioned thiols."

Jan 1, 1990

By Arthur L. Miller

Recent studies suggest that trace metals emitted by internal combustion engines are derived mainly from combustion of lubrication oil. This hypothesis was examined by investigation of the formation of particulate matter emitted from an internal combustion engine in the absence of fuel-derived soot. Emissions from a modified CAT 3304 diesel engine fueled with hydrogen gas were characterized. The role of organic carbon and metals from lubrication oil on particle formation was investigated under selected engine conditions. The engine produced exhaust aerosol with log normal-size distributions and particle concentrations between 105 and 101 cm-3 with geometric mean diameters from 18 to 31 nm. The particles contained organic carbon, little or no elemental carbon, and a much larger percentage of metals than particles from diesel engines. The maximum total carbon emission rate was estimated at 1.08 g h-1, which is much lower than the emission rate of the original diesel engine. There was also evidence that less volatile elements, such as iron, self-nucleated to form nanoparticles, some of which survive the coagulation process.

Jan 1, 2007

By H. J. Heinen

To maximize productivity through improved minerals processing technology, the U.S. Department of the Interior, Bureau of Mines, is investigating particle agglomeration techniques as a means of increasing the percolation rates of leach solutions in heap leaching of clayey gold-silver ores. Simulated heap leach experiments were conducted on 50-pound charges of ore that were contained in 5.5-inch-diameter columns, 5 feet in height. Results indicated that the percolation rate of cyanide leach solution could be enhanced markedly by mixing the ore with controlled amounts of lime, flocculants, and water, and then aging the mixture prior to the column leach step. Experimental results obtained on 20-mesh silver tailings and gold ore crushed to 3/8 inch and to 1 inch showed that it was possible to increase percolation rates as much as 100-fold without sacrificing silver-gold extraction. Larger scale tests conducted in 24-inch-diameter, 16-foot-high columns closely paralleled bench-scale results. By improving percolation leaching, these techniques have the potential of helping to solve environmental problems associated with tailings disposal as well as making an important economic impact on gold-silver recovery operations. Investigations are continuing to develop binders superior to lime for particle agglomeration pretreatment.

Jan 1, 1979

By S. M. Shelton

The widespread occurrence of domestic manganese deposits and the shortage of ferromanganese-grade ore have been sources of much speculation and investigative effort for many years. The present emergency has intensified the search by the Bureau of Mines for methods of producing ferromanganese-grade concentrates4/ from low-grade ores.

Jan 1, 1941

By S. M. Shelton

[The widespread occurrence of domestic manganese deposits and the shortage of ferromanganese-grade ore have been sources of much speculation and investigative effort for many years. The present emergency has intensified the search by the Bureau of Mines for methods of producing ferromanganese-grade concentrates4/ from low-grade ores.]

Jan 1, 1941

By D. P. Schlick

The German experience in dealing with the health hazard of respirable dust in underground mines is reported from first-hand observation in this Bureau of Mines paper. The report covers-- 1. The control of dust by water infusion, water spraying, and ventilation. 2. The sampling devices (tyndalloscope , konimeter , and BAT-I) and methods used to determine the dust concentrations in mines. 3. The systems of classifying hazardous and safe dust levels in mines. 4. The research facilities devoted to theoretical and applied work on mine dust and pneumoconiotic disease. Tile major research projects on dust and disease now underway in West Germany are outlined in an appendix.

Jan 1, 1970

By R. L. Lincoln

The effects of adding from 1 to 50 atomic percent (a/o) to vanadium were investigated by the Bureau of Mines. Properties studied included as-cast and annealed hardness, microstructure, fabricability at room temperature and elevated temperature, tensile strength, electrical resistivity, and oxidation resistance at 625° and 800° 2. Additions of small amounts of hafnium resulted in lessened as-cast hardness, decreased electrical resistivity, impaired roll- ability, increased oxidation resistance, and greater tensile strength. Larger amount of hafnium caused greater as-cast hardness, increased electrical resistivity, further impaired rollability, continued increase in oxidation resistance, and lessened tensile strength. INTRODUCTION The purpose of this study was to determine the effect of hafnium additions on the properties of vanadium and to learn if this binary alloy had any special or unusual properties. This investigation is a part of a larger research project in which new and expanded uses of vanadium are being sought. Domes tic vanadium is found frequently in combination with uranium, and because of the demand for uranium as a nuclear fuel, there now exists a surplus of vanadium-bearing minerals and vanadium pentoxide as a byproduct of uranium production. Primary principles of conservation demand that greater use be made of this readily available surplus; finding suitable metals to alloy with vanadium to enhance its properties is one way to increase its utilization. This report is the result of an investigation of the effects on the properties of vanadium when hafnium is added in amounts from 1 to 50 a/o.

Jan 1, 1962

By G. E. McElroy

[The ventilation of development faces In nines for diluting Gas or dist concentrations and, in hot nines for providing air-motion cooling effect, by fan-pipe units discharging high-velocity steams of air close to the face, is an important phase of mine ventilation. The effectiveness of such units depends largely on the air-flow distribution between the pipe discharge and the face, n subject on which little definite information is available. A study of the air flow from grills into rooms3/ has provided some basic data, but under conditions so different from mine fan-pipe installations in development ends that the data are of doubtful application to mine installations, owing to differences in air-flow conditions.]

Jan 1, 1940

By Michael R. Norland

Surface and subsurface stabilization of mining-related wastes through revegetation depends upon the physical, chemical, and biological condition of the waste following mining. Mining disturbances can significantly alter the soil physical, chemical, and biological characteristics of a site, reducing or eliminating mycorrhizal fungi from the soil. Mycorrhizae are economically and ecologically important because they can alleviate environmental stresses caused by lack of proper soil condition and because they are vital to stabilization of mining waste by increasing plant survival and biomass through increased nutrient and water uptake. This report discusses some of the ecological factors that may affect mycorrhizae-plant associations on mining-related wastes and provides general information on mycorrhizae inoculation technology.

Jan 1, 1993