Search Documents

By W. W. Adams, V. E. Wrenn

"Production of explosives in the United States during the calendar year 1935 decreased 2 percent from 1934, according to reports covering all companies engaged in the manufacture of explosives during those years.Reports from manufacturers showed a total production of 308,381,250 pounds of explosives; this quantity included 39,170,016 pounds of permissible explosives 5/ 200,323,559 pounds of high explosives other than permissibles, and 68,887,675 pounds of black blasting powder of which 34,222,625 pounds were granular powder and 34,665,050 pounds pellet powder.Coal mines consumed 89 percent of the total production of blasting powder, 99 percent of the total output of permissible explosives, and 11 percent of the output of other high explosives.The metal mines of the United States used 28 percent of all high explosives other than permissloles, less than 1 percent of all permissibles, and 1 percent of all black powder produced.Quarries and nonmetallic-mineral mines consumed 17 percent of the high explosives other than pormissibles, less than 1 percent of the permissible., and 3 percent of the blasting powder.Construction work required the largest quantity, 40 percent of all high explosives manufactured during the year. Less than 1 percent of the permissibles and 6 percent of the black powder produced during 1935 was used in construction work."

Nov 1, 1936

By George S. Rice, W. L. EGY, H. P. Greenwald, L. M. JONES

CHAPTER I. INTRODUCTION AND SUMMARY. BY GEORGE S. RICE. PREFATORY STATEMENT. This bulletin describes the second series of coal-dust explosion tests conducted by the Bureau of Mines in the experimental mine near Bruceton, Pa. It covers a period from 1913 to 1918, inclusive, of more or less consecutive testing, during which many important conclusions were drawn regarding the way a coal-dust explosion may originate, the mechanism of an explosion, and the methods of pre- venting explosions and of limiting incipient explosions. The manuscript was prepared in 1918, but its publication had to be put aside during the World War for more pressing publications and it was not until this fiscal year 1922 that funds could be allotted for its printing. Meantime the general facts concerning methods of preventing explosions have been made known to the mining industry, with great advantage, it is believed, as explosions of coal dust in mines in the United States have become infrequent. This fact, however, must not lull the consciousness of mining men to the terrible potential danger that lurks in untreated coal dust. The experiments described in this volume should be of aid to them in planning to keep the ever present coal dust in an innocuous condition. The first series-reported in Bulletin 56, "First Series of Coal-Dust Explosion Tests in the Experimental Mine"-included only pre- liminary tests of the ability to start explosions of coal dust under the conditions in the experimental mine. After this fact had been determined and several violent dust explosions had been demon- strated before large audiences of mining men, the work had to be suspended in order that necessary repairs and extensions might be made in the fall and winter of 1911-12. Although the question of the possibility of coal dust causing explo- sions had been considered for more than a century, and much testing in laboratory apparatus and in small surface galleries had been done, coal-mining men generally did not believe that coal dust was explo- sive and considered that fire damp or gases of unknown composition were responsible for the mine explosions that had cost thousands of lives in the various coal-mining countries during the last century. As coal mines increased in number, size, and depth, explosions became alarming in their frequency. Finally came the Courriéres disaster in northern France, 1906, by which 1,100 lives were lost, and the following year in this country, the Monongah mine explosion, in West Virginia, which killed 361 men, and the Darr explosion, in Pennsylvania, which killed 239 men. These two disasters, both in December, 1907, led Congress to make an appropriation for an in- vestigation of the causes of mine explosions. The funds became available July 1, 1908, and the work was placed under the United States Geological Survey's technologic branch, with the late Dr. Joseph A. Holmes in charge. Before undertaking the investigations Dr. Holmes visited Europe, accompanied by the senior author of this bulletin, to study the methods foreign countries used to prevent mine explosions, to obtain details regarding tests being made in several countries, to procure safer explosives and better safety lamps for use in gaseous and dusty mines, and to study the methods used in coal-dust explo- sion tests in the recently completed galleries at Altofts, England, and Liévin, France, and in the older galleries at Gelsenkirchen, Germany, and Frameries, Belgium. At all of these stations the explosions tests were made in surface galleries. The Austrian gallery at Segengottes, near Brünn, Moravia, visited by the writer in 1911, is an underground gallery, but the testing done in it was limited, dealing with ignition of coal dust rather than with propagation. Although the results obtained in the foreign galleries had indicated that coal dust was explosive, mining men in the respective countries were of the opinion that the dust would not explode under mine con- ditions. This situation led Dr. Holmes to the conclusion that testing must be done in a real mine, to make certain that the conclusion would be reliable and would be accepted by the mining public as decisive.

Jan 1, 1922

By C. Q. Cupps, R. F. Zaffarano, J. Fry

Reservoir oil analyses from seven wells in the Greater Clareton area have been included in a study of the original characteristics of oil in the Newcastle sandstone reservoir . These data correlated with areal location of the wells show an increase of saturation pressure in a general north - south or downdip direction . The increase amounts to about 500 psi in more than 17 miles , which corresponds to a depth increase of about 1,600 feet . To facilitate application of the data to engineering analyses , average characteristics are given for arbitrary north and south divisions of the 22 - mile - long producing area . The downdip increase of saturation pressure is taken as evidence of updip diffusion of solution gas from a somewhat higher concentration at the bottom of the reservoir . This effect is opposite to that previously observed in two prominent high- relief reservoirs in the Rocky Mountain area . The increasingly greater saturation pressures southward or downdip in the Greater Clareton area suggest a continuing migration of fluids into the structure .

Jan 1, 1964

By Kevin Malone

Chrysotile asbestos occurs in many counties in California, and a small production had been reported at times, but development of deposits had been disappointing. A reconnaissance survey by the Bureau of Mines indicated that several deposits in the serpentine belt in Shasta, Trinity, and Siskiyou Counties might contain enough asbestos of filler grade to supply the growing demand on the west coast. Accordingly from 1956 to 1958 parts of the Mount Eddy and Shasta View deposits were investigated by trenching and diamond drilling to determine their potential. The work comprised construction of roads, bulldozer trenching, excavation of areas for diamond drilling, sampling, and upping. The trenches were excavated to expose the surface extent of some of the asbestos-bearing areas, To determine the downward continuation of asbestos-bearing sections and to secure samples for test purposes, six diamond drill holes, totaling 1,738 linear feet, were drilled in two selected areas. The trenching and core-drilling indicated that the asbestos-bearing material occurs as ribs and lenses of varying thicknesses in a broad belt of serpentine, about 600 feet wide and several miles long,

Jan 1, 1962

By Loren R. Anderson

This is an Appendix of Volume I. It contains the results of the electric cone penetrometer soundings from the first phase of the testing program.

Jan 1, 1982

By Mukund O. Gangal

A deep cutting continuous miner, HH456, was tested under production-mining conditions at the Joanne Mine, Rachel W. Va., for about 1 ½ years (226 production days). The miner was run in two modes: a low head-rpm, deep cutting and high rpm, shallow-cutting mode. These tests confirmed that deep cutting and slow cutter speed reduce respirable dust significantly under production mining conditions. Quantitative reductions in dust, in deep vs shallow cutting, were 73°; in return air and 63% at the operator's location. Production rate, (tons/shift), and bit consumption rate did not show any relationship to deep or shallow cutting. Reliability and maintainability of the miner were worse in deep cutting mode due to cutter drive shaft failures; the cutter shaft problem was solved through improved material and design. Excluding the cutter shaft repairs. maintainability war similar for deep and shallow cutting,

Jan 1, 1979

By Thomas M. Garland

A field study was made by the Bureau of Mines in cooperation with oil companies to determine the feasibility of changing the injection profile of water-input wells after water breakthrough at producing oil wells. A secondary objective was to study the particle size and quantity of plugging material required to change the input profile and the methods of applying these materials. Fifty-three injection wells were treated with various amounts and types of plugging materials and the injection profile was definitely changed in most of the wells treated. Increased efficiency of water injection after treatment was indicated by tracer surveys and injection-well performance. There were some indications that the rate of water production was reduced and the rate of oil production was increased as a result of selective-plugging treatments, but ,s found that an immediate change in the rate of oil and water production did not normally occur. In many cases, beneficial results from a treatment may never be observed in the rate of oil or water production due to the many factors that affect the performance of producing and injection wells.

Jan 1, 1966

By John K. Alley

Fibrous silicon carbide was produced by thermal decomposition of certain silicates contained in graphite crucibles. Induction heating was used to produce the necessary temperature and thermal gradients. Both green and white fibers were mainly the beta modification even though each color grew within a different temperature zone. Alpha silicon carbide, present in insufficient amounts for X-ray detection, was identified by electron diffraction. The white fibers formed in a zone between 1,365° and 1,634° C (±50° C). The green fibers (less contaminated) formed in a much more narrow zone between 1,650° and 1,672° C (±50° C). The average lengths and widths of microscopic fibers grown by this method were 1.5 mm/0.002 mm (white) and 1.2 mm/0.0035 mm (green); however, same fibers observed by electron microscope had cross-sectional measurements of 150 to 300 A. Both differential thermal analysis and thermogravimetric analysis showed that silicon carbide fibers oxidized in air at temperatures above 500° C. Fibrous silicon carbide was indexed as a cubic cell with the dimensions a = 4.358 A. The density calculated from X-ray data was 3.217 g/cm3.

Jan 1, 1963

By Dennis R. Dolinar

Physical property tests were conducted on drill core from three exploratory holes on the Naval Oil Shale Reserve near Anvil Points, Colo. Data and regression analysis curves are presented. Data obtained above the Mahogany zone were used to estimate the potential zone of surface effects from under-ground mining. Single specimen testing was primarily used to obtain Mohr's envelope and subsequent rock properties. The technique is shown to provide satisfactory results for this rock type with a significant reduction of core preparation and testing time.

Jan 1, 1981

By D. Bienstock, J. H. Field, M. J. Lempel

A computer program is presented to perform the detailed and numerous calculations required for determining the interface temperatures and steady - state heat flow through a furnace wall composed of several refractories in layers . A method is developed that will allow the designer to determine the various thicknesses for each refractory layer to minimize either the total wall thickness or the cost of the wall per unit of area . A sample problem is presented and analyzed to illustrate the techniques involved .

Jan 1, 1964

Any communication system requires at least three elements in order to function: a transmitting device, a receiving device, and a transmission line or propagation medium. Even the device children use, tin cans connected with string, consists or these three elements. One speaks into one can (transmitter), which vibrates at the same frequencies as the voice. The string (transmission path) picks up the vibrations of the can and carries them along its entire length. The other can (receiver) detects the vibration and reproduces the original sounds to a lesser extent depending on distance, tightness of string, type of string, etc. All communication systems depend on these three elements: transmitter, transmission path, and receiver. Communication systems can be divided into three fundamental categories: wired phone systems, radio systems, and carrier current systems. Sections 2.2, 2.3, and 2.4, respectively, describe these systems and explain the basic principles of how each works. Hybrid systems are those systems that use various combinations of the three basic communication methods. Hybrid systems are described in section 2.5. There are some other methods of signaling (stench warning, bell signaling, etc.) that can be used in underground mines to transmit or convey information. These systems, although they cannot be considered true communication systems since they do not provide voice or even two-way communication, are briefly described in section 2.6. 2.2 Wired Phone Systems Wired phone systems are all those that depend on a wire connection between phones with the wire carrying the voice signals. Figure 2-1 is a diagram of two typical wired phone systems.The top panel shows a simple single pair party line system. In this system each phone is connected to a common pair of wires, and a person speaking into one phone will be heard at all the other phones on the line. The bottom panel shows a multipair private line phone system. In this type of system, each phone is connected by its own individual pair of wires to a central switch or telephone exchange. To establish a call between two phones in this system, the lines between the two phones must be connected (switched together) within the telephone exchange. In early exchanges, the connections were made manually by an operator. These exchanges are called Private Branch Exchanges (PBX's). Today, equipment within the exchange can automatically connect each phone to any other phone in the system. These exchanges are called Private Automatic Branch Exchanges (PABX's). There are many different types of automatic exchanges. Some utilize switches to physically make each connection according to the number dialed. Other, more advanced exchanges are completely solid state and may even be computer controlled. [ ]

Jan 1, 1984

By John S. Berber

Olefin and paraffin mixtures (C10-C16 and C10-C22) were separated from low-temperature lignite tar by urea adduction and sulfated to yield secondary alkyl sulfate detergents. The C10 ?C16 secondary alkyl sulfate showed a 99.3 percent biodegradability, and the C10-C22 fraction showed a 96.8 percent biodegradability, exceeding the required standard of 80 percent for the biodegradability of anionic detergents in washing and cleaning compounds. Chlorination of paraffins yielded a detergent of 93.2 to 93.4 percent biodegradability.

Jan 1, 1968

By Jack C. White

This U.S. Bureau of Mines report assesses the resource potential of trace metals present in commercial Ti mineral concentrates. Metals of greatest interest: are those defined as "strategic and critical" by the U.S. Congress in 1981. Metals of interest in Ti mineral concentrates are Cb, Cr, Ta, Th, U, V, and Zr. Commercially available Ti mineral concentrates were studied. Characterization and analysis of major and minor constituents were performed by X-ray diffraction, neutron activation, inductively coupled plasma emission, atomic absorption, and classical wet chemical techniques. Of the metals investigated, the Cb, Ta, and V content of some concentrates may be a significant potential resource, depending on their amenability to recovery.

Jan 1, 2010

By R. J. Leary

Significant improvements in surface conditions or mechanical properties of steels have been attributed by several investigators to ladle additions of small quantities of rare-earth metals or their oxides. To investigate systematically these effects in wrought and in cast plain carbon and alloy mechanical steels containing approximately 0.35 percent carbon, heats of four representative compositions were melted by the Bureau of Mines in a 4-ton open-hearth furnace. Each heat was cast into three sets of ingots to exemplify respectively, treatments with (1) rare-earth metals, (2) rare-earth metal oxides, and (3) an untreated set as a control. The development of melting, casting and rolling practices is described and discussed. Lance injection of oxygen shortly after melt raised the temperature of the metal immediately as much as 500° F., principally because mechanical agitation exposed the high-carbon metal to the flame and furnace root. An exceptional degree of superheat in the metal at the termination of the refining period was attributed to oxygen injection during the refining period. Bath temperatures higher than industrial practice were permitted by the all-basic furnace lining. Rates of carbon elimination as high as 0.036 percent carbon per minute were achieved by oxygen injections.

Jan 1, 1961

By Abrasive Materials

Table 1.-Salient abrasive statistics in the United States [ ]

Jan 1, 1967

By V. E. Edlund

Laboratory batch flotation tests were conducted on copper converter slags to evaluate the relative merits of recovering copper from slow-cooled versus water-quenched slags. Three slags containing 1.6, 5.0, and 6.6 percent copper were used. More than 90 percent of the copper was recovered in a rougher concentrate leaving a 0.2- to 0.3-percent copper tailings when treating slow-cooled slag. Lower recoveries and higher copper tailings ranging from 0,5 to 0.6 percent copper were obtained from quenched slag. Grindability studies were made on the respective heat-treated slags. Quenched slags proved more difficult to grind than slow-cooled slags. Cost studies showed that (1) the cost of slow cooling and crushing off-sets any advantages of higher copper recoveries from slow-cooled slag, and (2) water-quenched slag, which requires no crushing preparatory to grinding, could be treated more economically. Costs based on processing 1,000 tons of slag per day would be $1.85 per ton for quenched slag versus $2.37 per ton for slow-cooled slag.

Jan 1, 1971

By Michael S. Wieland

This report investigates whether it is tractable and thereupon reasonable to remove the booster influences when ranking the toxic fumes of non-cap-sensitive mining explosives. The hazard potential is represented by relative fume toxicity RFT, the resultant influence computed from a formulated rule with a restricted set (tally) of fume components and multiplying constants. The RFT result is compared to the rule criterion that represents the worst case tolerable toxicity stipulated by regulations or otherwise. The typical nonstoichiometric booster composition can render notable unwanted influence on the RFT ranking results. Historically, the remedy was to shoot the booster separately and reduce the trial concentrations by the relevant subtractions. Unreal negative concentration results were noted on rare occasions, revealing the faulty nature of the reduction procedure. With thermodynamic reaction chemistry codes TDRC, on the other hand, the booster ingredients can be retained in or removed from the reactant tabulation, yielding reduction factors taken as the concentration ratios for the two circumstances. The underlying presumption regarding reduction factors is that the ratios of component concentrations with and without the booster ingredients when resolved theoretically ought to equal those rendered experimentally, when tractable. Upon rearranging the presumed relationship, the unadjusted fume concentrations divided by theoretical reduction factors yield the wanted readjusted fume concentrations, thereby removing the booster influence without generating unreal negative concentrations. The work principle from thermodynamics restricted by the constraint of zero-net interaction loss is utilized in conjunction with the TDRC to resolve the wanted (Z-state) fume spectrum. This circumvents the recognized difficulty with traditional hydrodynamic detonation theory that is related to the nonideal reaction characteristics of typical mining explosives. The tacit characteristic of the Z-state resolved from the non-trajectory work principle is that it can not be remedied or tampered with, unlike the traditional trajectory techniques where the reaction products can be readjusted by changing formula representations, nullifying specific reactions or otherwise manipulating the thermodynamic trajectory process. Though the work principle theory is an unfinished formulation, the Z-state results prove worthy enough for rendering trends and comparisons and reaching otherwise useful conclusions. Further refinements should yield more reliable fume spectra and indicate explosive composition readjustments that would reduce toxic effects within underground mines and the wider world environment.

By J. A. Lamonica

The Bureau of Mines studied a pulsation damping device designed to smooth pulsating flow in personal respirable dust samplers. The effect on the pulsation dampener efficiency of six parameters was investigated, as follows: Volume, diaphragm elasticity, diaphragm area, center orifice area, inlet-outlet orifice area, and geometry (LID ratio). The results indicate that volume pre-dominates in determining snubber efficiency, while the other parameters become important at small volumes. Geometry has no effect on snubber efficiency. Criteria for an efficient pulsation dampener construction were obtained.

Jan 1, 1971

By D. J. Bauer

The Bureau of Mines demonstrated the feasibility of fractionating lanthanide nitrates with a tertiary amine on lanthanum-cerium and thulium-ytterbium pairs. Optimum values were determined for pH, phase concentration, and percent chelation of metal ions in the aqueous phase. Percent extraction is markedly dependent on the concentration of lithium nitrate in the aqueous phase. Selective masking of the heavier element in each extraction system with DTPA or EDTA aqueous-phase chelating agents resulted in lanthanum-cerium separation factors of 8.5 and thulium-ytterbium separation factors of 3.4.

Jan 1, 1966

By V. A. Marple, K. L. Rubow, Y. Tao

"A personal diesel exhaust aerosol sampler has been designed and evaluated in both laboratory and field settings. The sampler uses size selective sampling for the determination of the respirable mass concentrations of mineral dust and diesel exhaust particulate matter found in underground coal mines. This design is based on the premise that diesel exhaust particulate matter is predominantly less than 0.8 um while mineral dust is greater than 0.8 gm. Operating at a flow rate of 2 L/min, the sampler consists of a 10 mm Dorr-Oliver respirable dust cyclone followed by an 0.8 gm cutpoint impactor and an afterfilter. Field evaluations consisted of sampling at 6 different locations in these underground coal mines. Measured aerosol concentration less than and greater than 0.8 um have been compared with a well characterized cascade impactor.Techniques must be developed for measuring the mass concentration of diesel exhaust particulate matter found in underground coal mines due to the health concerns associated with worker exposure to diesel exhaust particulate matter. Diesel exhaust particles are in the respirable size range and have been regarded as a potential occupational carcinogen by NIOSH (1988). Furthermore, a 1988 MSHA advisory committee directed MSHA to develop a sampling protocol for assessing worker exposure to diesel exhaust particles.The University of Minnesota and the Bureau of Mines, over the past 4 years have measured the size distribution of diesel exhaust particles and mineral dust, both in the laboratory and underground mines (Cantrell, 1987; Cantrell et al., 1987; Cantrell and Rubow. 1988; Marple et al, 1986; Rubow et al., 1988: and Watts et al., 1989). To date, measurements have been made in nine coal mines. Seven mines utilized diesel-powered equipment at the mine face while two used electric-powered equipment. The results of these field tests indicate that mineral dust and diesel exhaust particles can be differentiated on the basis of particle size. The measured particle size distributions have been found to be bimodal with a saddle point at 0.8 um. This has led to the hypothesis that one method for measuring worker exposure to diesel exhaust particles would be to collect size fractionated particle samples separated at 0.8 um with the diesel particles being less than 0.8 um and the mineral dust particles greater than 0.8 um.Aerosol size distribution measurements, using a micro-orifice uniform deposit impactor (MOUDI), have been conducted in the mine intake air portal, intake entry to the working section, haulageway, and section return entry. The MOUDI is a ten stage cascade impactor with particle cutpoints ranging from 0.1 to 15 um aerodynamic diameter (Marple and Rubow. 1984b; Marple et al., 1989). The sampling flow rate is 30 L/min."

Mar 1, 1992