Search Documents

By Thomas L. Chapman

The San Manuel is a deposit of low-grade disseminated copper ore. It was brought to the attention of the government in October 1942 through an application to the Reconstruction Finance Corporation for a development loan, supported by a report by Henry W. Nichols. Nichols' sampling of two outcrops containing copper silicate and his geologic map indicated that a minable body of copper ore might be developed. The Federal Geological Survey was requested to examine the property. The Survey mapped the geology in March 1943 and cut a few check samples, which substantially confirmed Nichols' sampling of the outcrops and a few shallow workings. The geologists of the Survey recommended some test drilling by the Bureau of Mines. The property was examined by the author and Wm. D. Hughes, associate engineer of the Bureau of Mines on March 22 and 26, 1943, and a preliminary drilling campaign was recommended. Five shallow churn-drill holes totaling 1,480 feet were put down under the supervision of Chas. A. Kumke, one of the Bureau's engineers, from November 23, 1943, to January 13, 1944. This work indicated that the deposit extended deeper than the 350-foot depth attained in the deepest hole and might have very considerable areal extent. Additional funds were allotted, and the drilling contract was extended twice to a final maximum of 17,000 feet with 2,000 feet maximum depth of hole. Drilling was continued by the Bureau of Mines until February 2, 1945, when 15,844 feet of hole had been drilled. The Magna Copper Co. took options on this and adjoining property in September 1944 and commenced drilling with two machines. It also engaged the two contract drills used by the Bureau after it stopped drilling. It exercised its options in August 1945 and organized the San Manuel Copper Corp. to operate the property. That company is continuing to explore the ore body with six churn drills. Thomas Lyon took options early in 1945 on holdings adjoining the San Manuel property on the east and is operating two churn drills. Exploration up to the completion of the last holes started by the Bureau of Mines indicated a block of ore 3,100 feet long, 400 to 800 feet wide, and 500 to 900 feet thick, and averaging about 0.8 percent copper. Subsequent drilling showed that the ore body extends considerably beyond this block. The axis of the ore body strikes about N. 61° E. Copper minerals are disseminated in hydrothermally altered quartz monzonite and monzonite porphyry. Ore outcrops in two small areas over the northeast part of the block. Elsewhere the copper-bearing rocks are capped by Gila conglomerate, which thickens toward the west and south. Drilling showed that the ore is in a thick, tabular body with a steep dip to the south. The ore body lies near the surface in the northeastern part of the block. The south side of the block is much farther below the surface than the north side. There the upper part of the copper-bearing rocks is lightly mineralized, so that the hanging wall of minable ore lies deeper than the base of the conglomerate cap, which thickens southward.

Aug 1, 1947

By Thoms L. Chapman

The San Manuel is a deposit of low-grade disseminated copper ore. It was brought to the attention of the government in October 1942 through an application to the Reconstruction Finance Corporation for a development loan, supported by a report by Henry W. Nichols. Nichols’ sampling of two outcrops containing copper silicate and his geologic map indicated that a minable body of copper ore might be developed. The Federal Geological Survey was requested to examine the property. The Survey mapped the geology in March 1943 and cut a few check samples, which substantially confirmed Nichols’ sampling of the outcrops and a few shallow workings. The geologists of the Survey recommended some test drilling by the Bureau of Mines. The property was examined by the author and W. D. Hughes, associate engineer of the Bureau of Mines on March 22 and 26, 1943, and a preliminary drilling campaign was recommended. Five shallow churn-drill holes totaling 1,480 feet were put down under the supervision of Chas. A. Kumke, one of the Bureau’s engineers, from November 23, 1943 to January 15, 1944. This work indicated that the deposit extended deeper than the 350-foot depth attained in the deepest hole and might have very considerable areal extent. Additional funds were allotted, and the drilling contract was extended twice to a final maximum of 17,000 feet with 2,000 foot maximum depth of hole. Drilling was continued by the Bureau of Mines until February 2, 1945, when 15,844 feet of hole had been drilled. The Magma Copper Co. took options on this and adjoining property in September 1944 and commenced drilling with two machines. It also engaged the two contract drills used by the Bureau after it stopped drilling. It exercised its options in August 1945 and organized the San Manuel Copper Corp. to operate the property. That company is continuing to explore the ore body with six churn drills. Thomas Lyon took options early in 1945 on holdings adjoining the San Manuel property on the east and is operating two churn drills. Exploration up to the completion of the last holes started by the Bureau of Mines indicated a block of ore 5,100 feet long, 400 to 800 feet wide, and 500 to 900 feet thick, and averaging about 0.8 percent copper. Subsequent drilling showed that the ore body extends considerably beyond this block. The axis of the ore body strikes about N. 61º E. Copper minerals are disseminated in hydrothermally altered quartz monzonite and monzonite porphyry. Ore outcrops in two small areas over the northeast part of the block. Elsewhere the copper-bearing rocks are capped by Gila conglomerate, which thickens toward the west and south. Drilling showed that the ore is in a thick, tabular body with a steep dip to the south. The ore body lies near the surface in the northeastern part of the block. The south side of the block is much farther below the surface than the north side. There the upper part of the copper-bearing rocks is lightly mineralized, so that the hanging wall of minable ore lies deeper than the base of the conglomerate cap, which thickens southward.

Aug 1, 1947

By J. F. Shultz

The Bureau of Mines investigated the hydrogenation of carbon monoxide and carbon dioxide over Raney nickel catalyst and nitrided fused-iron catalyst using both a single-pass and a recycle system. Activation energy over Raney nickel catalyst is 29 to 32 kcal/mole for synthesis from either CO or CO2, Pressure dependence of the gas conversion is to the 0.3 power for synthesis from CO and to the 0.5 power for synthesis from CO2. Nitrided fused-iron catalysts were tested using high recycle rates and 3H2+lCO, 2H2+lCO, and 1H2+lCO feed gas at 21.4 atmospheres absolute pressure. The relative usage of hydrogen (moles H2 consumed per moles Ha+CO consumed) was larger than in corresponding single-pass tests, and the relative usage of hydrogen approached the feed gas ratio monotonically as conversion increased. Activation energy was found to be 12 or 13 kcal/mole fresh feed gases of 3H2+lCO or 2H2+lCO. For single-pass operation the activation energy under the same conditions was 19 to 21 kcal/mole.

Jan 1, 1967

By R. D. Currie

Haulage accidents in the anthracite region cause fewer fatal and lost-time accidents per million man-hours than similar accidents in bituminous mines, a fact that may be accounted for in several ways, but primarily because haulage, in a large part of the region, is restricted to haulage crews operating only on the gangways where most of the miners seldom come in contact with movement or handling of cars and locomotives. Generally in underground mines the number of men injured compared with the number killed is greater for haulage than for roof-fall accidents, while the number of men killed by haulage is second only to the number killed by roof falls.

Jan 1, 1939

By R. G. Nelson

The mechanical properties of low-hafnium, arc-melted, Kroll-process zirconium are presented. The effect of temperature on the ultimate strength, yield strength, proportional limit, elongation, hardness, Young's modulus, electrical resistivity, and impact strength are shown, The effects of cold work and annealing on the tensile properties, bend radius, and formability, as determined by cupping tests, are also given, Tensile properties are compared, in part, to those obtained on earlier graphite-melted zirconium and on crystal-bar zirconium. INTRODUCTION The commercial production of high-purity, low-hafnium bearing zirconium has been achieved, and this metal is becoming available for industrial use. However, there is little published information regarding the physical and mechanical properties of this product; and, since there have been many improvements in the production and arc-melting techniques of zirconium in the past 3 years, it was considered advisable to present the properties of the vastly improved zirconium representative of current production.

Jan 1, 1954

By H. W. St. Clair

This study of the rate of evaporation of zinc was undertaken as a part, of a general investigation on refining mixtures of metals resulting from melting reclaimed scrap. One of the methods by which the more volatile metals, such as zinc, magnesium, and cadmium, may be separated is by distillation. Distillation may be carried out at lower temperatures if it is done in an evacuated enclosure. The immediate purpose of the present investigation was to determine accurately the effect of temperature, pressure, and other factors on the rate of evaporation of zinc.

Jan 1, 1950

By M. J. Beus

The Bureau of Mines, under a cooperative agreement with Hecla Mining Co., is conducting a rock mechanics study of the 6,200-ft-deep circu-lar, concrete-lined Silver Shaft in northern Idaho. The objective of the project was to instrument and evaluate lining behavior and rock de-formation when a deep shaft is constructed in a high in situ stress field and anisotropic rock mass. Rock mass displacements were moni-tored with multiple-position borehole extensometers. Liner stress and strain were measured with concrete pressure cells and embedment strain gauges. Field data from the 5,955-ft test level show that rock displacement is controlled by rock mass anisotropy. Liner stress and strain levels reflect the high in situ stress field as well as nearby station and raise construction. Maximum stresses measured in the lining, as a result of shaft excavation, are about one-third of its compressive strength. Subsequent loading pocket excavation resulted in signifi-cantly increased stress and strain levels in the liner. Continued monitoring and preliminary analysis of the data indicate that concrete-lined, circular shafts are stable for the high, unequal horizontal stress fields and rock anisotropy encountered in deep-level mining. Adjacent development work can be expected to significantly alter the initial stress and displacement conditions.

Jan 1, 1984

By Anthony W. Sparks

The Bureau of Mines conducted tests designed to compare its breathing metabolic simulator (BMS) with other methods that are currently used to evaluate the performance of respiratory protective equipment. The BMS is a commercially developed device that uses a piston cylinder to simulate breath movement. Using a propane furnace that consumes oxygen and forms CO2, the BMS also simulates the respiratory metabolism of humans. The breathing and metabolic subsystems of the BMS are described in detail in this report. Results are compared from tests that used the BMS to evaluate respiratory equipment and from tests that used human subjects for the same purpose. The BMS was also tested against a pulsatile breathing machine (PBM) previously designed by the Bureau. Both machines were used to test respiratory equipment, and the test results are compared in this report. To illustrate typical applications of the BMS, the report briefly describes how the BMS was used to test two different types of closed-circuit respiratory apparatus, and the test results are presented. This research showed that BMS test results compared more closely to the results of tests that used human subjects than did results obtained using the PBM.

Jan 1, 1980

By Aleksandar D. Bugarski

Three types of uncatalyzed diesel particulate filter (DPF) systems, three types of high-temperature disposable filter elements (DFEs), and one diesel oxidation catalytic converter (DOC) were evaluated in underground mine conditions for their effects on the concentrations and size distributions of diesel aerosols. Those effects were compared with the effects of a standard muffler. The experimental work was conducted directly in an underground environment using a unique diesel laboratory developed in an underground experimental mine. The DPF systems reduced total mass of aerosols in the mine air approximately 10-fold for light-load and 20-fold or more for high-load test conditions. The DFEs offered similar reductions in aerosol mass concentrations. The efficiency of the new DFEs significantly increased with accumulation of operating time and buildup of diesel particulate matter in the porous structure of the filter elements. A single laundering process did not exhibit substantial effects on performance of the filter element. The effectiveness of DPFs and DFEs in removing aerosols by number was strongly influenced by engine operating mode. The concentrations of nucleation mode aerosols in the mine air were found to be substantially higher for both DPFs and DFEs when the engine was operated at high-load modes than at low-load modes. The effects of the DOC on mass and number concentrations of aerosols in mine air were relatively minor when compared to those of the DPF and DFE systems.

Jan 1, 2009

By Jennifer S. Riefenberg

The U.S. Bureau of Mines conducts basic and applied research related to predicting, eliminating, and/or controlling rock bursts in underground hard-rock mines and coal bumps in underground coal mines. An important element in this research is the development of a reliable and efficient microseismic source location technique. This report presents the results of a Bureau study to develop and evaluate a new algorithm to locate microseismic events based on the Simplex method, a powerful linear programming technique. The technique was tested on both field data and simulated data. Microseismic event source locations obtained with this new Simplex-based algorithm were shown to have less error than those locations obtained using a least squares method. It was concluded that the Simplex approach to source location of microseismic events can be used effectively in microseismic monitoring.

Jan 1, 1989

By H. H. Schrenk, Carlton E. Brown

"INTRODUCTION The angle at which a hole is drilled has long been thought to affect the amount of dust disseminated into the air during wet drilling. The amount disseminated has been reported as increasing rapidly with the approach of the angle of the hole to the vertical (up) position. 4/ This has been explained commonly as being caused by a decrease in contact of water with the face of the drill hole; increase in amount of sludge dropping through the air; and increase in amount of sludge running down the drill steel and being thrown into the air by the rotation of the drill steel and by leakage of air from the front head of the drill.The steep up angles of the holes drilled are responsible, at least partly, for the higher dust concentrations found in such places as raises, compared with those at level faces, where most of the holes are drilled at angles farther from the vertical (up) position. The mining industry is coming to realize more and more the importance of the angle of the drill hole as a contributing cause of the high dust concentrations found in some raises. Much work is being done to counteract the effect of the angle of the drill hole on dust dissemination. The rate of rater flow through drill steels is being increased by the use of water tubes of larger diameter or by higher water pressures to obtain better contact between water and the face of the drill hole. Traps are being developed to catch the sludge from the drill hole and allow it to drain down through a special pipe before it drops through the air or runs down the drill steel. Drills that permit little or no air to leak from the front head along the drill steel are being designed and used. Care is being taken to prevent the exhaust from the drill dispersing the sludge into the air."

Feb 1, 1938

By Albert J. Rambosek

The results obtained in a study of the stress conditions existing in a drill bit-point area and in the underlying rock, when the bit was in full but nonpenetrative contact with the rock, are presented. This investigation by the Bureau of Mines was the preliminary exploratory phase of a long-range program of research on rock drilling to establish criteria for the maximum economically feasible rate of rock penetration. The photoelastic technique of experimental stress analysis was the principal method used to obtain the data. Transparent models and transmitted light were employed to investigate patterns in drill-bit models and isotropic materials under the bit when subjected to a concentrated static load. Comparative stress data for anisotropic rock were obtained by the reflective photoelastic technique. Brittle lacquer and an extensometer were used obtain supplementary information wherever substantiating data were desired to check photoelastic results. The zone of maximum shear occurs along an arc near the contact face of the bit. The stress distribution pattern in an isotropic model rock near the area contacted by the bit was nearly a mirror image of that exhibited within a similar areal zone of the bit. The stress pattern in granodiorite specimens was similar, though not symmetric, to the pattern in the isotropic model rock. The asymmetry of the stress pattern in the granodiorite was attributed to the anisotropic characteristics of the constituent minerals of various sizes.

Jan 1, 1963

By L. A. Neumeier

The Bureau of Mines evaluated the properties and anisotropy in properties of rolled Zn-Cu and Zn-0.12 pct Ti-Cu alloys with various copper additions to 1.25 pct. The alloys were rolled cold and at various hot-rolling temperatures to reductions as high as 92 pct after breakdown rolling. The properties are extremely sensitive to various combinations of composition, rolling temperature, and rolling reduction, Zn-Cu alloys can develop good creep resistance, but they are inferior in that respect to Zn-Ti-Cu alloys. For alloys either with or without the titanium addition, cold-rolling results in recrystallization of the matrix and rejection of copper from solution, causing poor hardness, tensile, and creep properties, but high ductility. Peak tensile strengths develop when the alloys are rolled in the range 320° to 400° F, Best creep resistance for Zn-Cu alloys requires higher rolling temperatures when copper content is increased. Creep resistance is best for Zn-Ti-Cu alloys with about 0.75 to 1.0 pct CU rolled near 480° F. Some copper is soluble in the TiZn15 phase, which forms into "stringers" during rolling. The possible contributions to creep behavior of factors such as distribution of second-phase particles, grain size, and preferred orientation are discussed.

Jan 1, 1970

Although the technology involved in removing material from below the earth's surface has a long history, communication systems in underground workings are relatively new to the industry. Communication equipment did not begin appearing in underground mines until the early 1900's. Figure 1-1 shows a miner using a Western Electric standard telephone set for underground mines in 1913. These early phones were essentially the same as those used aboveground, except that they were enclosed in cast-iron boxes as protection against moisture, acid fumes, and gases.

Jan 1, 1984

By Frank J. Wiebelt

Work on the Abbott-quicksilver property was part of the general program of th~ Bureau of Mines in its investigation of domestic mineral resources, which are essential to national defense or industry and of which our present or probable future supplies are inadequate. The mine was discovered in 1862, and the intermittent production up to 1947 has totaled around 37,500 flasks of quicksilver. Output has come from ore shoots formed in the vicinity of fault intersections in a narrow zone composed of lenses of silicified serpentine breccia interbedded with shale. Work by the Bureau included the drilling of six diamond-drill holes aggregating 2,845 feet. Several possible ore zones were intersected by the drill holes. Field work was begun in April 1948 and concluded in October of the same year. This report gives detailed results of the diamond drilling and a brief account of the history and description of the ore deposits.

Jan 1, 1949

By Ernest L. Corp

Seepage forces computed by a finite-element flow program are combined with gravity forces in an elastic-plastic stress-analysis program to determine the stability of mine-waste slopes. Computer output provides a cross-sectional plot of the dam or embankment showing the safety factors for each element. The combined finite-element program called SEEP-SLOPE was used to analyze several trial embankments and the 1972 Buffalo Creek Dam failure Safety factors computed by the finite-element method (FEM) were compared with those computed by Bishop limiting-equilibrium method. For individual slip circles, there was little correlation between the factors of safety computed by the two methods. Both predict failure, but FEM shows a different mode of failure plus development of potential failure zones not indicated by conventional methods. Besides having a better theoretical basis than the Bishop method, FEM requires no assumptions regarding the location or geometry of the failure surface. As a result, the program will show progressive development of a failure zone, and areas can be pinpointed where remedial measures should be taken. In addition, nonhomogeneous cross sections can be analyzed, and zones of potential piping can be defined.

Jan 1, 1975

By Maria I. De Rosa

The U.S. Bureau of Mines performed experiments to determine the embedded hydrogen chloride (HCI) and smoke particle characteristics during combustion of polyvinyl chloride (PVC) and chlorinated mine materials for development of a test parameter. The experiments were conducted in an approximately 20-L furnace at set furnace temperatures of 250° and 1,000° C, for a 14-min duration, with an airflow through the furnace of 10 L/min. The variables studied, as a function of time, were hydrogen chloride embedded on smoke particles, hydrogen chloride concentrations in the gas phase, smoke particle average diameter (dg) and particle concentration (no), and product of smoke particle diameter and concentration (dgno). Other variables included carbon monoxide (CO), carbon dioxide (CO2), and oxygen (O2) concentrations; sample mass weight loss; and furnace temperatures. Results show that there is a correlation between embedded hydrogen chloride, hydrogen chloride gas concentrations, and inverse of the smoke particle diameter-concentration product (1/dgno); the higher the hydrogen chloride gas concentrations, the higher the embedded hydrogen chloride, the higher the 1/(dgno) values. These correlations will enable development of a simple test parameter to assess the toxic hazard that these materials pose during fire.

Jan 1, 2010

By D. H. Baker

THIS REPORT presents the technique and equipment used in determining the hardness of titanium sponge. Detailed descriptions are given of the methods used in preparing test samples for chemical analysis and hardness testing, the method of melting and surfacing test ingots, and the technique of reading Brinell-hardness impressions. The arc-melting furnace described, for which engineering drawings are included, will produce from 70 to 90 double-melted buttons each 8 hours of operation. Experimental data are also presented depicting the effect on hardness of the methods of surfacing specimens, temperature of test specimens, and the effect of time at test load. These data show that surfacing of the specimen involves no critical machining operations but that the test surface must be paralleled by a relatively flat surface for contact with the anvil of the Brinell tester. The heating of a specimen to 150° C. during surfacing does not materially affect the results if the ingot is cooled to room temperature before the hardness impressions are made. The optimum time at load appears to be approximately 30 seconds, but load times of as much as 1/ ½ minutes will not cause major errors.

Jan 1, 1959

By Roy L. Wilfong, LeRoy R. Furlong, Louis P. Domingues

The bulk and apparent densities , particle size , and surface area of ceria powders derived from the ammonium sulfate , carbonate , nitrate , oxalate , and sulfate salts and heated at 950 ° to 1,500 ° C for 1 to 24 hours were studied . The bulk and apparent densities and particle size generally increased , and surface area decreased with increase in temperature and time of heating ; surface area was more sensitive to changes in temperature and time than the other properties studied . These properties of the ceria powders had a marked dependence on temperature and a lesser dependence on duration of heating at a given temperature ; and the source of oxide and thermal treatment cannot be considered optional in the preparation of refractory powders by thermal decomposition . The ammonium sulfate and sulfate salts heated at 950 ° and 1,200 ° C produced oxide powders with the lowest bulk density , the smallest particle size , and the highest surface area . The highest apparent densities were achieved for oxides resulting from the carbonate and the sulfate but the carbonate - derived material was considerably coarser . The surface areas of ceria powders derived from cerium salts decrease in the order of sulfate , ammonium sulfate , nitrate , oxalate , and carbonate . The observation of these physical properties are useful in predicting the sintering behavior of various oxide powders .

Jan 1, 1964

By Linda C. Carrico

Those who manage the Nation's mineral resources rely upon a variety of organizations both public and private--to give them accurate mineral data, technical guidance, and expert advice. This directory provides a list of such organizations--a list that should prove a useful tool for those seeking mineral-related information and technical assistance. The directory lists Federal and State governmental agencies and national, regional, and State associations with activities in the mineral, metal, and material sectors of the economy. These organizations regulate mining, monitor mineral production, establish and enforce health and safety standards, identify and evaluate mineral resources, conduct scientific research, predict market trends, resolve environmental issues, and promote the interests of the mineral industry, its individual sectors, and its workers--to name a few of their functions. The listings in this directory--arranged by State--should help users who manage mineral resources identify agencies and organizations that can provide mineral-related information or technical assistance.

Jan 1, 1993